HTP-2500/2600 Quick Start Guide
Connect each speaker to the receiver using the
supplied speaker wires.
To connect, insert the colored wire into the matching colored (+) tab
and the other wire into the black (–) tab as shown below. Connect the
center speaker the same way (matching the wire the color-coded label).
Check that you have all the
accessories.
Put the batteries in the remote
control and stick the non-skid pads
to the base of the speakers.
1
3
2
Surround right
Surround left
STANDBY/ON
MUTE
Open the battery compartment on
the rear of the remote control.
1
SLEEP
STATUS
DIMMER
Note that the color-coded tabs are as follows:
INPUT SELECTOR
DIGITAL STB DVD/DVR
TUNER
EDIT
Speaker cord (x1)
• Red : Front right speaker
• White : Front left speaker
• Green : Center speaker
• Purple : Subwoofer
• Grey : Surround right speaker
• Blue : Surround left speaker
FM/AM TAPE/VCR
TV
CLASS
Insert the supplied batteries
2
TUNING
STATION
–
+
–
+
following the markings inside the
SYSTEM
SETUP
CH LEVEL
VOLUME
battery compartment to align
them correctly.
+
FM wire antenna
ENTER
ROOM
SETUP
TEST
TONE
–
AUTO
SURROUND STEREO
Replace the battery compartment
cover.
3
Receiver
OFF SOUND TONE
MPX
Batteries (x2)
BASS
TREBLE
–
+
–
+
Listening position
Stick the self-adhesive non-skid
4
pads to the underside of each
speaker, and to the underside of
the subwoofer. Use four pads per
speaker (see below).
SPEAKERS
SUB
RECEIVER
FRONT
SURROUND
R L
CENTER
R
L
WOOFER
+
+
AM loop
antenna
Subwoofer
Remote control
–
–
Brackets (x4)
You should also have:
• Speakers (x5)
• Subwoofer
Screws (x4)
For the best surround sound, set up your
speakers like this. The front left and right
speakers should be about 6–9 feet apart.
Non-skid pads
(1x20, 1x4)
• Operating instructions
• Warranty card
Front right
Center
Front left
Subwoofer
Front and surround speakers
Center speaker
Plug the receiver, DVD player/
After switching on, make any
Connect the receiver to your DVD
player/ recorder.
Use a coaxial digital cord (not supplied) to connect the digital
output of your DVD player/ recorder to the DIGITAL INPUT
(COAXIAL) DVD/DVR jack.
Connect antennas
4
6
7
5
recorder and TV into a convenient
necessary settings required by the
DVD player/ recorder, then you're
ready to start enjoying your home
theater system.
AC outlet.
Connect the FM wire antenna and fully extend along a
window frame or another suitable place that gives good
reception.
1
1
2
Press ꢀ STANDBY/ON to switch on the receiver.
1
Refer to the receiver's operating instructions for a detailed
explanation of this system's surround sound features.
Use a red/white stereo audio cord (not supplied) to connect the
AUDIO TV IN jack on the receiver to the audio output on your
TV.* This will allow you to listen to your TV through this
speaker system.
To connect the AM loop antenna, twist the exposed wire
strands together and insert into the terminal, then snap
the connector shut as shown below.
2
ꢀ
STANDBY/ON
INPUT SELECTOR
AUTO
SURROUND STEREO
VOLUME
* Note that you must also connect the DVD player/ recorder's
video output to your TV's video input to watch a DVD video
(video cable is not supplied).
DIGITAL
STB DVD/DVR
ꢀ
STANDBY/ON
+
AM loop
antenna
FM/AM TAPE/VCR
TV
–
Receiver
DIGITAL INPUT
(COAXIAL)
DVD/DVR
FM wire antenna
Switch on your DVD player/ recorder and TV, and set the TV to
the correct video input.
Receiver
AUDIO
TV IN
2
+
+
IN
ANTENNA
OUT
–
–
L
FM
UNBAL
VIDEO 1
75Ω
ꢀ
AM
LOOP
VIDEO SELECT
Receiver
ꢀ
STANDBY/ON
TV
L
R
VIDEO
IN
AUDIO
OUT
TV
ꢀ
STANDBY/ON
VIDEO
OUT
DIGITAL
OUT
3/8 in.
(10mm)
DVD player/ recorder
DVD player/ recorder
For detailed instructions, see the Operating Instructions supplied and / or contact one of our knowledgeable Pioneer Customer Service Representatives at 1 - (800) 421-1404.
|