PL1IRR Remote Control
User’s Guide
IMPORTANT INFORMATION
Warnings and Notices
When using electrical equipment, basic safety precautions should always be followed including the following:
a. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
b. Do not use outdoors.
c. Do not use near gas or electric heaters.
d. The use of accessory equipment not recommended by the manufacturer may cause an unsafe
condition.
e. Do not use this equipment for other than intended use.
f. Refer service to qualified personnel.
SAVE THESE INSTRUCTIONS.
WARNING: You must have access to a main circuit breaker or other power disconnect device
before installing any wiring. Be sure that power is disconnected by removing fuses or turning the
main circuit breaker off before installation. Installing the device with power on may expose you to
dangerous voltages and damage the device. A qualified electrician must perform this installation.
WARNING: Refer to National Electrical Code® and local codes for proper use specifications.
WARNING: This equipment is intended for use in accordance with the National Electric Code® and
local regulations. It is also intended for installation in indoor applications only. Before any electrical
work is performed, disconnect power at the circuit breaker or remove the fuse to avoid shock or
damage to the control. It is recommended that a qualified electrician perform this installation.
WARNING: The PL1IRR Remote Control contains a Class 2 laser. Do not look directly into laser
beam or damage to eye may result. Handle with caution.
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
LASER DIODE
WAVELENGTH: 630 - 680 nm
MAX OUTPUT: <5 mW
Philips Selecon Limited Three-Year Warranty
Philips Selecon offers a three-year limited warranty of its products against defects in materials or workmanship
from the date of delivery. A copy of Philips Selecon three-year limited warranty containing specific terms and
Philips Selecon office.
1
User’s Guide
PL1IRR Remote Control
TABLE OF CONTENTS
Philips Selecon Limited Three-Year Warranty............................................................................................... 1
Product Description......................................................................................................................................... 3
Infrared Remote Control Features................................................................................................................... 4
2
TABLE OF CONTENTS
PL1IRR Remote Control
User’s Guide
PREFACE
About this Guide
The document provides installation and operation instructions for the following product:
• PL1IRR Remote Control (includes two AAA batteries and user’s guide)
Please read all instructions before using this product. Retain this manual for future reference. Additional information
Product Description
The PL1IRR Remote Control is used to remotely program and control presets (1 through 6 and Off) of PL1 LED
luminaires (IR-enabled models only) over an unobstructed range of approximately 100 feet. IR-enabled PL1 LED
Luminaires have an integrated infrared (IR) receiver that allows them to receive IR commands from the PL1IRR
Remote Control. Using the Remote, colors (full color mixing)/presets/intensity can be programmed/selected, raised
and lowered, and fixtures may be turned On and Off.
Before Using the Infrared Remote
To install two AAA batteries (included)
in PL1IRR remote:
Step 1. At rear of remote, remove battery
access panel by sliding it as
indicated.
Step 2. Note orientation of batteries as
indicated in battery compartment
of remote.
Step 3. Install batteries.
Step 4. Reinstall battery access panel.
Step 5. Remote is ready for use.
PL1IRR Remote
WARNING! PL1IRR Remote contains a
Class 2 laser. Do not stare or look directly
into laser beam.
LASER RADIATION
DO NOT STARE INTO BEAM
_
CLASS 2 LASER PRODUCT
LASER DIODE
+
WAVELENGTH: 630 - 680 nm
MAX OUTPUT: <5 mW
+
_
Slide battery access panel away
from remote to install batteries.
AAA Battery (2 each -
supplied with remote)
Battery Compartment
Access Panel
Figure 1: PL1IRR Remote Battery Installation
3
User’s Guide
PL1IRR Remote Control
PL1IRR PROGRAMMING REMOTE OVERVIEW
Infrared Remote Control Features
Laser / IR Window -
Laser and IR programming emits from
this end.
Program -
Enter - After the luminaire to be
programmed is selected (by Laser),
press Enter to set the luminaire to
programming mode.
PL1IRR LED (indicator) -
PROGRAM
Laser (Luminaire Selector) - Press
Laser to select individual luminaire for
programming / adjustment.
The LED indicator will flash each time
a button is pressed.
ENTER
LASER
EXIT
CANCEL
LEARN
Intensity Raise/Lower -
Exit - Press to exit programming mode.
Press top button to raise intensity and
bottom button to lower it. Tap the up
for 2% increase or tap down for a 1%
decrease. Press and hold (top or
bottom button) for sequential raise/
lower.
INTENSITY
COLOR
Cancel -
Cancels the learn features (any
programming made will not be
recorded) RGBW will not be changed.
S
T
S
S
T
S
T
T
RED
GREEN
BLUE
WHITE
Learn -
Individual LED Color Adjustment -
After adjustments are made, the Learn
button (in conjunction with a preset
button) stores the new settings to a
specific preset if desired.
Allows the raising or lowering of
individual LED colors. Press top
button to change color and bottom
button to lower it. Tap the up for 2%
increase or tap down for a 1%
decrease. Press and hold (top or
bottom button) for sequential raise/
lower.
PRESETS
WHITE
WARM
COOL
DAY
Preset (White Color Temperature) -
1
4
2
5
3
6
Presets (6 Levels or Off) -
Allows selection of Warm, Cool or Day
color temperatures.
Allows selection and programming of
one of six Presets (1 through 6) or
Preset Off.
OFF
PL1IRR
Note, only intensities may be stored
on White Color Temperature presets.
These presets cannot be edited or
changed
Note, Off cannot be edited or changed.
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
WARNING! THIS DEVICE IS A CLASS 2 LASER. DO
NOT STARE OR LOOK DIRECTLY INTO BEAM.
LASER DIODE
WAVELENGTH: 630 - 680 nm
MAX OUTPUT: <5 mW
Figure 2: PL1IRR Programming Remote
4
PL1IRR PROGRAMMING REMOTE OVERVIEW
PL1IRR Remote Control
User’s Guide
OPERATION AND PROGRAMMING
Using the PL1IRR Infrared Remote Control
To select and program PL1 LED luminaire with PL1IRR remote:
Note: The IR, on the PL1 LED luminaire, must be set to "Enabled" in order for the PL1IRR remote to communicate
and control the fixture. Refer to PL1 LED Luminaire Installation & User’s Manual on luminaire menu settings.
Step 1. Point PL1IRR programming remote
Laser / IR window directly at luminaire
PL1 LED Luminaire
IR programming window (as shown in
Figure 2) and hit "Enter" button. Note,
(IR-enabled model)
each luminaire to be programmed/
adjusted needs to be selected and
programmed/adjusted individually.
Step 2. Point PL1IRR remote directly at
luminaire IR window and hit "Laser"
button. Luminaire to be programmed or
adjusted is now selected.
PL1 IR
Port
Note: At luminaire IR port, a Blue LED will
illuminate when the fixture is in programming
mode and blink Red when buttons are pressed on
IR remote to confirm it sees the remote and is
receiving commands.
PROGRAM
ENTER
LASER
EXIT
CANCEL
LEARN
INTENSITY
COLOR
S
T
S
T
S
T
S
T
RED
GREEN
BLUE
WHITE
PL1IRR Remote Control
PRESETS
WHITE
WARM
COOL
DAY
1
4
2
5
3
6
OFF
PL1IRR
Step 3. Set luminaire to preset or make
adjustments as desired.
Step 4. To save settings, hit "Learn" button and
then hit any Preset button (except Off -
Off cannot be programmed). Preset is
Figure 3: PL1 LED Luminaire Programming / Control
now saved. To cancel programming, hit "Cancel" button.
Step 5. After programming or adjustments are complete, hit "Exit" button. Repeat, as desired, on additional
luminaires to be programmed/adjusted.
Note: Refer to PL1 LED Luminaire Installation & User’s Manual for additional information. This manual is
Troubleshooting
Description
Symptom
Possible Cause/Remedy
Luminaire not selected by laser...
Reselect luminaire by repeating luminaire selection step.
Not seeing IR remote control...
Make sure batteries are good in remote. Try fresh, fully charged
batteries.
Make sure IR is enabled in the fixture menu.
Insure IR remote is pointing at IR window in luminaire and that there
is nothing in between IR remote and luminaire IR window.
Clean luminaire IR window.
Fixture will not respond to IR
remote programming unit.
IR remote programming.
5
|