Always there to help you
Register your product and get support at
SBT10
Question?
Contact
Philips
User manual
SBT10_37_UM_V1.0_EN.indd
1
7/29/2013 4:01:48 PM
Contents
1 Important safety instructions
2
2 Your portable speaker
Introduction
3
3
3
4
What's in the box
Overview of the speaker
3 Get started
Charge the built-in battery
Power on/off
5
5
5
4 Use Bluetooth devices
Connect a device
6
6
6
7
7
Play audio via Bluetooth
Make a call
Clear the pairing information
5 Listen to an external device
8
6 Product information
General information
Bluetooth
9
9
9
9
Amplifier
7 Troubleshooting
General
10
10
10
About Bluetooth device
8 Notice
11
11
Compliance
Disposal of your old product and
batteries
Trademark notice
Copyright
11
12
12
EN
1
SBT10_37_UM_V1.0_EN.indd
1
7/29/2013 4:01:48 PM
•
Danger of explosion if battery is
incorrectly replaced. Replace only with
the same or equivalent type.
1 Important safety
instructions
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
d Follow all instructions.
e Do not use this apparatus near water.
f Clean only with dry cloth.
Warning
• Never remove the casing of this apparatus.
• Never lubricate any part of this apparatus.
• Never place this apparatus on other electrical
equipment.
g Do not block any ventilation openings.
Install in accordance with the
manufacturer's instructions.
h Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that
produce heat.
Caution
• Removal of the built-in battery invalidates the warranty
and may destroy the product.
i Only use attachments/accessories
specified by the manufacturer.
Always bring your product to a professional to
remove the built-in battery.
j Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
k Apparatus shall not be exposed to
dripping or splashing.
Note
• The type plate is located on the back of the product.
l Do not place any sources of danger on
the apparatus (e.g. liquid filled objects,
lighted candles).
m Battery shall not be exposed to excessive
heat such as sunshine, fire or the like.
•
Perchlorate Material - special handling
hazardouswaste/perchlorate.
2
EN
SBT10_37_UM_V1.0_EN.indd
2
7/29/2013 4:01:49 PM
2 Your portable
speaker
Congratulations on your purchase, and
welcome to Philips!To fully benefit from the
support that Philips offers, register your product
Introduction
With this speaker, you can
•
•
•
listen to audio from an external device via
Bluetooth connection,
listen to audio from an external device
through the AUX socket, and
make phone calls.
What's in the box
Check and identify the contents of your
package:
•
•
•
Main unit
USB cable
Short user manual
Always there to help you
Register your product and get support at
SBT11
Question?
Contact
Philips
Short User Manual
EN
3
SBT10_37_UM_V1.0_EN.indd
3
7/29/2013 4:01:49 PM
Overview of the speaker
a
b
c
d
g
h
e
f
d Bluetooth indicator
a
•
Indicate the current Bluetooth
•
•
Power the speaker on or off.
When the speaker is powered
off, press and hold to clear pairing
information.
connection status.
e AUX
•
Connect to an external player.
f DC 5V
b
c
•
Recharge the built-in battery.
•
During a call, mute the integrated
microphone or release it from mute
status.
g Integrated microphone
h BATT
•
During charging, indicate the current
•
•
•
•
Start, pause, or resume play.
Press to answer an incoming call.
Press to end the current call.
Press and hold to reject an incoming
call.
battery status.
•
•
Press twice to dial the last called
number.
Press twice to hold on the current call
and answer another incoming call.
4
EN
SBT10_37_UM_V1.0_EN.indd
4
7/29/2013 4:01:50 PM
3 Get started
Power on/off
Press and hold for 2 seconds.
Always follow the instructions in this chapter in
sequence.
Note
• If an audio input cable is connected to the AUX socket,
this product does not automatically power off.To save
battery power, disconnect the audio input cable or
manually power off the product after use.
Charge the built-in battery
• In Bluetooth mode, if Bluetooth connection is invalid for
15 minutes, this product automatically powers off.
The speaker is powered by a built-in
rechargeable battery.
Note
• Before use, fully charge the built-in battery.
Connect the USB cable between
•
•
the DC 5V socket on the speaker, and
a USB socket of a computer.
Charging indicator
The indicator on the bottom indicates the
battery status during charging.
Indicator Battery
Solid
green
Off
Under charging
Fully charged
EN
5
SBT10_37_UM_V1.0_EN.indd
5
7/29/2013 4:01:51 PM
Disconnect a device
4 Use Bluetooth
devices
On your device, disable the Bluetooth
connection with this product.
Note
With this speaker, you can listen to audio from
a player and make a call through Bluetooth.
• Before connecting another Bluetooth device, disconnect
the current device first.
Note
• Make sure that no audio input cable is connected to
the AUX socket.
• Philips does not guarantee the compatibility with all
Bluetooth devices.
• Before pairing a device with this system, read its user
manual for Bluetooth compatibility.
• The product can memorize a maximum of 8 paired
devices.
Reconnect a device
•
For a paired Bluetooth device on which
the automatic reconnection is enabled,
this product reconnects with it once it is
detected.
• Make sure that Bluetooth function is enabled on your
device, and your device is set as visible to all other
Bluetooth devices.
• Any obstacle between this system and a Bluetooth
device can reduce the operational range.
• Keep away from any other electronic device that may
cause interference.
•
For a paired Bluetooth device that does
not support the automatic reconnection,
reconnect it with this product manually.
Play audio via Bluetooth
Note
Connect a device
• If the connected Bluetooth device supports the
Advanced Audio Distribution Profile (A2DP), you can
listen to tracks that are stored on the device through
the system.
• If the device also supports the AudioVideo Remote
Control Profile (AVRCP), you can control play on this
product.
• If the connected device does not support the AVRCP,
control play on the connected device.
• If there is an incoming call on the connected mobile
phone, music play pauses.
1 Power on the speaker.
2 On your device, search for Bluetooth
devices.
3 In the device list, select PHILIPS SBT10.
•
•
If a message prompts for the
permission for Bluetooth connection
with PHILIPS SBT10, confirm it.
If a password is required, enter 0000
and then confirm.
Buttons Functions
Note: Make sure that no audio input cable is
connected to the AUX socket.
Bluetooth indicator
Start, pause, or resume play.
Indicator
Bluetooth connection
Blinking
blue
Connecting or waiting for
connection
Solid blue Connected
6
EN
SBT10_37_UM_V1.0_EN.indd
6
7/29/2013 4:01:51 PM
Make a call
Buttons Functions
Press to answer an incoming call.
Press to end the current call.
Press and hold to reject an incoming
call.
Press twice to dial the last called
number.
Press twice to hold on the current
call and answer another incoming call.
Mute the integrated microphone or
release it from mute status.
Clear the pairing information
When the product is powered off, press and
hold for 8 seconds.
EN
7
SBT10_37_UM_V1.0_EN.indd
7
7/29/2013 4:01:51 PM
5 Listen to an
external device
You can also listen to an external audio device,
for example, MP3 player, through this product.
1 Connect an audio input cable with a 3.5
mm connector on both ends to
•
•
the AUX socket on this product, and
the headphone socket on the external
device.
2
Play audio on the external device (refer to
its user manual).
8
EN
SBT10_37_UM_V1.0_EN.indd
8
7/29/2013 4:01:51 PM
6 Product
information
Note
• Product information is subject to change without prior
notice.
General information
Power Supply (through USB
socket)
5V, 0.6 A
Built-in Battery
Lithium
battery
Dimensions - Main Unit (W x
H x D)
107 x 71 x
36 mm
Weight - Main Unit
0.12 kg
Bluetooth
Bluetooth specification
Supported profiles
V2.1+EDR
HFP v1.6,A2DP v1.2,
HSP v1.2
Amplifier
Rated Output Power
Signal to Noise Ratio
AUX Input
1.2 W RMS
> 62 dBA
600 mV RMS, 22
kOhm
EN
9
SBT10_37_UM_V1.0_EN.indd
9
7/29/2013 4:01:52 PM
•
This product is already connected with
another Bluetooth-enabled device.
Disconnect that device and then try again.
7 Troubleshooting
The paired device connects and disconnects
constantly.
Warning
•
The Bluetooth reception is poor. Move the
device closer to this product or remove
any obstacle between them.
For some devices, Bluetooth connection
may be deactivated automatically as a
power-saving feature.This does not indicate
any malfunction of this product.
• Never remove the casing of this device.
To keep the warranty valid, never try to repair
the system yourself.
•
If you encounter problems when using this
device, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips Web page (www.
philips.com/support).When you contact Philips,
make sure that the device is nearby and the
model number and serial number are available.
General
No power
•
Recharge your speaker.
No sound
•
•
Adjust volume on the connected device.
When you listen to audio through
Bluetooth, make sure that no audio input
cable is connected to the AUX socket.
Make sure that your Bluetooth device is
within the effective operational range.
•
No response from the speaker
Restart the speaker.
•
About Bluetooth device
The audio quality is poor after connection
with a Bluetooth-enabled device.
•
The Bluetooth reception is poor. Move the
device closer to this product or remove
any obstacle between them.
Cannot connect with the device.
•
The Bluetooth function of the device is not
enabled. Refer to the user manual of the
device for how to enable the function.
10 EN
SBT10_37_UM_V1.0_EN.indd 10
7/29/2013 4:01:52 PM
•
•
Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
8 Notice
Any changes or modifications made to this
device that are not expressly approved by
Philips Consumer Lifestyle may void the user’s
authority to operate the equipment.
RF Radiation Exposure Statement: This
equipment complies with FCC’s and IC’s RF
radiation exposure limits set forth for an
uncontrolled environment.The antenna(s)
used for this transmitter must be installed and
operated to provide a separation distance of
at least 20 cm from all persons and must not
be collocated or operating in conjunction with
any other antenna or transmitter. Installers must
ensure that 20cm separation distance will be
maintained between the device (excluding its
handset) and users.
Compliance
Notice for the USA and Canada
This device complies with Part 15 of the FCC
Rules and RSS standard of Industry Canada.
Operation is subject to the following two
conditions:
1 this device may not cause harmful
interference, and
Disposal of your old product
and batteries
2 this device must accept any interference
received, including interference that may
cause undesired operation.
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
Never dispose of your product with other
household waste. Please inform yourself about
the local rules on the separate collection of
electrical and electronic products and batteries.
The correct disposal of these products helps
prevent potentially negative consequences on
the environment and human health.
Your product contains batteries, which cannot
be disposed of with normal household waste.
Please inform yourself about the local rules on
separate collection of batteries.The correct
disposal of batteries helps prevent potentially
negative consequences on the environment and
human health.
additional information on a recycling center in
your area.
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules
and ICES-003 of Industry Canada . These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation.This equipment generates, uses,
and can radiate radio frequency energy and,
if not installed and used in accordance with
the instruction manual, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is encouraged
to try to correct the interference by one or
more of the following measures:
•
•
Relocate the receiving antenna.
Increase the separation between
equipment and receiver.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
EN 11
SBT10_37_UM_V1.0_EN.indd 11
7/29/2013 4:01:52 PM
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
Trademark notice
®
The Bluetooth word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by Philips is
under license.
Copyright
2013 © Koninklijke Philips Electronics N.V.
Specifications are subject to change without
notice.Trademarks are the property of
Koninklijke Philips Electronics N.V or their
respective owners. Philips reserves the right
to change products at any time without being
obliged to adjust earlier supplies accordingly.
12 EN
SBT10_37_UM_V1.0_EN.indd 12
7/29/2013 4:01:52 PM
PHILIPS LIMITED WARRANTY
ONE (1) YEAR
WARRANTY COVERAGE:
PHILIPS warranty obligation is limited to the terms set forth
below.
Philips, or (d) if any Philips serial number has been removed or
defaced, or (e) product, accessories or consumables sold “AS IS”
without warranty of any kind by including refurbished Philips
product sold “AS IS” by some retailers.
WHO IS COVERED:
Philips warrants the product to the original purchaser or the per- This Limited Warranty does not cover:
son receiving the product as a gift against defects in materials and
workmanship as based on the date of original purchase
(“Warranty Period”) from an Authorized Dealer. The original
sales receipt showing the product name and the purchase date
from an authorized retailer is considered such proof.
•
•
Shipping charges to return defective product to Philips.
Labor charges for installation or setup of the product, adjust-
ment of customer controls on the product, and installation or
repair of antenna/signal source systems outside of the product.
Product repair and/or part replacement because of improper
installation or maintenance, connections to improper voltage
supply, power line surge, lightning damage, retained images or
screen markings resulting from viewing fixed stationary con-
tent for extended periods, product cosmetic appearance items
due to normal wear and tear, unauthorized repair or other
cause not within the control of Philips.
Damage or claims for products not being available for use, or
for lost data or lost software.
Damage from mishandled shipments or transit accidents when
returning product to Philips.
A product that requires modification or adaptation to enable
it to operate in any country other than the country for which
it was designed, manufactured, approved and/or authorized, or
repair of products damaged by these modifications.
A product used for commercial or institutional purposes
(including but not limited to rental purposes).
•
WHAT IS COVERED:
The Philips warranty covers new products if a defect in material
or workmanship occurs and a valid claim is received by Philips
within the Warranty Period. At its option, Philips will either (1)
repair the product at no charge, using new or refurbished
replacement parts, or (2) exchange the product with a product
that is new or which has been manufactured from new, or ser-
viceable used parts and is at least functionally equivalent or most
comparable to the original product in Philips current inventory,
or (3) refund the original purchase price of the product.
Philips warrants replacement products or parts provided under
this warranty against defects in materials and workmanship from
the date of the replacement or repair for ninety (90) days or for
the remaining portion of the original product’s warranty,
whichever provides longer coverage for you. When a product or
part is exchanged, any replacement item becomes your property
and the replaced item becomes Philips’ property. When a refund
is given, your product becomes Philips’ property.
•
•
•
•
•
•
Product lost in shipment and no signature verification receipt
can be provided.
Failure to operate per Owner’s Manual.
Note: Any product sold and identified as refurbished or
renewed carries a ninety (90) day limited warranty.
TO OBTAIN ASSISTANCE IN THE U.S.A., CANADA,
PUERTO RICO, OR U.S. VIRGIN ISLANDS…
Contact Philips Customer Care Center at:
1-866-309-0845
Replacement product can only be sent if all warranty
requirements are met. Failure to follow all requirements
can result in delay.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS
WARRANTY IS THE EXCLUSIVE REMEDY FOR THE CON-
SUMER. PHILIPS SHALL NOT BE LIABLE FOR ANY INCIDEN-
TAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF
ANY EXPRESS OR IMPLIED WARRANTY ON THIS PROD-
UCT. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE
LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT
IS LIMITED IN DURATION TO THE DURATION OF THIS
WARRANTY.
WHAT IS NOT COVERED - EXCLUSIONS AND
LIMITATIONS:
This Limited Warranty applies only to the new products manu-
factured by or for Philips that can be identified by the trademark,
trade name, or logo affixed to it. This Limited Warranty does not
apply to any non-Philips hardware product or any software, even
if packaged or sold with the product. Non-Philips manufacturers,
suppliers, or publishers may provide a separate warranty for their
own products packaged with the bundled product.
Some states do not allow the exclusions or limitation of inciden-
tal or consequential damages, or allow limitations on how long an
implied warranty lasts, so the above limitations or exclusions may
not apply to you.
Philips is not liable for any damage to or loss of any programs,
data, or other information stored on any media contained within
the product, or any non-Philips product or part not covered by
this warranty. Recovery or reinstallation of programs, data or
other information is not covered under this Limited Warranty.
This warranty does not apply (a) to damage caused by accident,
abuse, misuse, neglect, misapplication, or non-Philips product, (b)
to damage caused by service performed by anyone other than
Philips or Philips Authorized Service Location, (c) to a product or
a part that has been modified without the written permission of
This warranty gives you specific legal rights. You may have other rights which vary from state/province to state/province.
P&F USA, Inc. PO Box 2248, Alpharetta, GA 30023-2248
3140 035 51091
SBT10_37_UM_V1.0_EN.indd 13
7/29/2013 4:01:52 PM
P&F USA Inc.
PO Box 2248
Alpharetta, GA 30023-2248
Phone 1 866 309 0845
Meet Philips at the Internet
Specifications are subject to change without notice
© 2013 Koninklijke Philips Electronics N.V.
All rights reserved.
SBT10_37_UM_V1.0
SBT10_37_UM_V1.0_EN.indd 14
7/29/2013 4:01:52 PM
|