Always there to help you
Register your product and get support at
AZ1837
Question?
Contact
Philips
User manual
Contents
1 Important
2
2
Safety
2 Your CD Soundmachine
Introduction
4
4
4
4
What's in the box
Overview of the main unit
3 Get started
Install batteries
Connect power
7
7
7
4 Use your CD Soundmachine
Play a CD
8
8
8
8
8
8
Play from USB device
Listen to radio
Control play
Select play modes
5 Other features
Program tracks
10
10
10
Listen to an external device
6 Product information
11
11
USB playability information
7 Troubleshooting
12
12
Troubleshooting
8 Notice
13
EN
1
•
Protect the power cord from being
walked on or pinched, particularly at plugs,
convenience receptacles, and the point
where they exit from the device.
Only use attachments/accessories specified
by the manufacturer.
Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer or sold with the device.
When a cart is used, use caution when
moving the cart/device combination to
avoid injury from tip-over.
1 Important
•
•
Safety
This 'bolt of lightning' indicates uninsulated
material within the device may cause an
electrical shock. For the safety of everyone in
your household, please do not remove the
covering.
The 'exclamation mark' calls attention to
features for which you should read the enclosed
literature closely to prevent operating and
maintenance problems.
WARNING:To reduce the risk of fire or electric
shock, the device should not be exposed to rain
or moisture and objects filled with liquids, such
as vases, should not be placed on the device.
CAUTION:To prevent electric shock, fully
insert the plug. (For regions with polarized
plugs:To prevent electric shock, match wide
blade to wide slot.)
•
•
Unplug this device during lightning storms
or when unused for long periods of time.
Refer all servicing to qualified service
personnel. Servicing is required when the
device has been damaged in any way, such
as power-supply cord or plug is damaged,
liquid has been spilled or objects have
fallen into the device, the device has been
exposed to rain or moisture, does not
operate normally, or has been dropped.
Battery usage CAUTION –To prevent
battery leakage which may result in bodily
injury, property damage, or damage to the
device:
•
•
•
•
Do not mix batteries (old and new or
carbon and alkaline, etc.).
Install the battery correctly, + and - as
marked on the device.
The batteries shall not be exposed to
excessive heat such as sunshine, fire or
the like.
Remove battery when the device is
not used for a long time.
Important Safety Instructions
•
•
•
•
•
Follow all instructions.
Heed all warnings.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings.
Install in accordance with the
manufacturer's instructions.
Do not install near any heat sources such
as radiators, heat registers, stoves, or other
device (including amplifiers) that produce
heat.
•
•
•
Device shall not be exposed to dripping or
splashing.
Do not place any sources of danger on
the device (e.g. liquid filled objects, lighted
candles).
•
2
EN
•
Where the plug of the Direct Plug-in
Adapter is used as the disconnect device,
the disconnect device shall remain readily
operable.
Warning
• Never remove the casing of this device.
• Never lubricate any part of this device.
• Never place this device on other electrical equipment.
• Keep this device away from direct sunlight, naked
flames or heat.
• Never look into the laser beam inside this device.
• Ensure that you always have easy access to the power
cord, plug, or adaptor to disconnect this device from
the power.
EN
3
2 Your CD
Soundmachine
Congratulations on your purchase, and
welcome to Philips!To fully benefit from the
support that Philips offers, register your product
Introduction
With the CD Soundmachine, you can:
•
•
•
•
play CDs, MP3/wma discs
play mp3/wma files on USB devices
listen to FM/MW radio
program the play sequence of tracks.
What's in the box
Check and identify the contents of the package:
•
•
•
•
Main unit (without batteries)
1 x AC/DC power adaptor
1 x MP3 link cable
User Manual
Overview of the main unit
4
EN
a b c
d
e
f
n m l k
j
i
h g
o
r
q
p
•
Adjust volume.
a Source selector: CD•USB/MW/FM/OFF
•
Select CD•USB, MW(AM), FM source,
or turn off the unit.
d Display panel
Show current status.
•
b
e OPEN/CLOSE
Press to open or close the disc
compartment.
•
USB socket.
•
c VOL+/-
EN
5
f Tuning
•
Tune to radio stations.
g USB
•
Select USB device source.
Select CD source.
h CD
•
i - ALBUM +
•
For MP3-CDs: skip to the next/
previous album in an MP3-CD.
j
/
•
•
Select the previous/next track.
Search backward/forward.
k
l
•
Pause or resume play.
•
•
Stop play.
Erase a program.
m MODE
Select a play mode: REPEAT or
SHUFFLE.
•
n PROG
For MP3-CDs: program tracks and
browse the program.
•
o Telescopic antenna
•
Adjust FM reception.
p MP3 LINK
•
Socket for connecting an external
device.
q DC IN
•
Power supply socket.
r Battery compartment
6
EN
3 Get started
Connect power
Caution
Caution
• Risk of product damage! Make sure that the power
supply voltage corresponds to the voltage printed on
the back or the underside of the product.
• Risk of electric shock! When you unplug the AC power
cord, always pull the plug from the socket. Never pull
the cord.
• Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
radiation exposure or other unsafe operation.
• Before you connect the AC power cord, make sure that
you have completed all other connections.
Always follow the instructions in this chapter in
sequence.
If you contact Philips, you will be asked for the
model and serial number of this apparatus.The
model number and serial number are on the
bottom of the apparatus.Write the numbers
here:
Note
• To save energy: switch the source selector to OFF
after use.
• The device switches to standby mode if keeps inactive
for 15 minutes.
Model No. __________________________
Serial No. ___________________________
Install batteries
Note
• You can use both batteries and AC power as power
supply of this device.
1 Open the battery compartment.
2 Insert 6 x 1.5V R14/UM2/C CELL
batteries (not supplied) with correct
polarity (+/-) as indicated.
3 Close the battery compartment.
6 x 1.5V R14/UM2/C CELL
EN
7
4 Press
/
to select a file, and press
4 Use your CD
Soundmachine
to start play.
•
•
To stop play, press
To pause or resume play, press
.
.
Listen to radio
Play a CD
1 Switch the MW/FM selector to MW or
FM.
Note
2 Rotate TUNING until you find optimal
• You cannot play CDs encoded with copyright
protection technologies.
reception.
Tip
You can play commercially available audio CDs:
• To improve FM reception, you can extend, incline, or
turn the telescopic antenna for best reception.
• To improve MW reception, turn the device to face a
different direction.
•
•
•
•
CD-Recordables (CD-R)
CD-Rewritables (CD-RW)
MP3-CDs
WMA-CDs
1 Switch the source selector to CD•USB.
2 Press and open the lid of the CD
compartment.
Control play
3 Insert a CD with the printed side facing up,
Buttons Functions
and then close the CD lid.
VOL
Rotate to adjust the volume.
Stop play.
4 Press CD to select CD source, and press
to start play.
Pause or resume play.
Press to select a previous/next track.
Press and hold to fast backward/
forward.
» [ ] is displayed.
/
•
•
To stop play, press
To pause or resume play, press
.
.
Play from USB device
Note
• When search reaches the end of the last track, the CD
stops.
Note
• Make sure that the USB device contains playable audio
contents for supported formats.
1 Insert a USB storage device into the
Select play modes
socket.
2 Switch the source selector to CD•USB,
1 Press MODE repeatedly to select a play
and then press USB to select USB source.
mode:
•
[
] (repeat) – repeat a track
3 Press - ALBUM + to select a folder.
8
EN
•
[
ALL] (repeat all) - repeat an entire
CD/program
•
•
[
[
] (shuffle) - play tracks randomly
] (shuffle repeat all)
- repeat all tracks randomly.
2 To return to normal play, press MODE
repeatedly until play mode icons are no
longer displayed.
Tip
• Shuffle play cannot be selected when you play
programmed tracks.
EN
9
5 Other features
Program tracks
You can program up to 20 tracks in the desired
sequence.
1 In stop mode, press PROG to start to
program play sequence.
» [PROG] and [P01] are displayed.
2 For MP3-CDs, press - ALBUM + to select
an album.
3 Press
/
to select a track, and then
press PROG to confirm.
4 Repeat steps 2 to 3 to program more
tracks.
» When all 20 tracks are stored, no
more tracks can be selected and [FUL]
is displayed.
5 To play program, press
.
•
In stop mode, press and hold PROG to
browse programmed tracks.
6 To delete program, press in stop mode.
» [CLr] is displayed.
Listen to an external device
You can also listen to an external audio device
through this unit.
For an audio device with a headphone socket:
1 Connect the supplied MP3 LINK cable to:
•
the MP3-LINK socket on the back of
the unit.
•
the headphone socket on an MP3
player.
2 Start to play the MP3 player. (See the user
manual of the MP3 player.)
10 EN
•
•
Directory nesting up to a maximum of
8 levels
Number of albums/ folders: maximum
99
Number of tracks/titles: maximum 999
ID3 tag v2.0 or later
File name in Unicode UTF8 (maximum
length: 128 bytes)
6 Product
information
•
•
•
Note
• Product information is subject to change without prior
notice.
Unsupported formats:
•
Empty albums: an empty album is an
album that does not contain MP3/
WMA files, and is not be shown in the
display.
Unsupported file formats are skipped.
For example,Word documents (.doc)
or MP3 files with extension .dlf are
ignored and not played.
AAC,WAV, PCM audio files
DRM protected WMA files (.wav, .m4a,
.m4p, .mp4, .aac)
Power supply
- AC/DC power
adaptor
Model: SEF0800100E1BA
Input: 100-240V~, 50/60
Hz, 0.3 A
Output: 8.0V 1.0 A
6 x 1.5V R14/UM2/C CELL
batteries
•
- Battery
•
•
Power
Active <12 W
consumption
Power output
USB
2 x 1 W RMS
300 mA
•
WMA files in Lossless format
Operating
temperature
range
-10 °C - 50 °C
14 °F -122 °F
Dimensions (W
x H x D)
Weight
341 x 122 x 236 mm
1.8 kg
USB playability information
Compatible USB devices:
•
USB flash memory (USB 2.0 or
USB1.1)
•
•
USB flash players (USB 2.0 or USB1.1)
memory cards (requires an additional
card reader to work with this
apparatus)
Supported formats:
•
•
•
USB or memory file format FAT12,
FAT16, FAT32 (sector size: 512 bytes)
MP3 bit rate (data rate): 32-320 Kbps
and variable bit rate
WMA v9 or earlier
EN 11
•
Make sure that the CD is a finalized CD/
CD-R/CD-RW.
Make sure that the laser lens is clean.
Make sure that the CD is not encoded
with copyright protection technologies.
7 Troubleshooting
•
•
The CD skips tracks
•
Make sure that the CD is not damaged or
dirty.
Troubleshooting
•
Make sure that program/shuffle mode is
deactivated.
Warning
• Never remove the casing of this device.
USB device or SD/MMC card not supported
•
The USB device or SD/MMC card is
incompatible with the apparatus.Try
another one.
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
device, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips Web page (www.
philips.com/support).When you contact Philips,
make sure that the device is nearby and the
model number and serial number are available.
No power
•
•
•
•
Make sure that the AC power plug of the
unit is connected properly.
Make sure that there is power at the AC
outlet.
Insert the batteries with their polarities
(+/– signs) aligned as indicated.
Replace the battery.
No sound
•
•
Adjust the volume.
Make sure that the track played is of a
compatible format.
Display does not function properly. /No
reaction to operation of any of the controls.
•
•
Disconnect the AC power cord.
Connect the AC power cord after a few
seconds.
Cannot play disc
•
Make sure that the disc label is inserted
with the printed side facing up.
Wipe the disc with fibre cleaning cloth
from the centre to the edge in a straight
line.
•
•
This disc may be defective. Play another
disc.
12 EN
because correct disposal helps to prevent
negative consequences for the environmental
and human health.
8 Notice
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
This product complies with the radio
interference requirements of the European
Community.
Any changes or modifications made to this
device that are not expressly approved by
Philips Consumer Lifestyle may void the user’s
authority to operate the equipment.
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
Windows Media and the Windows logo
are trademarks, or registered trademarks of
Microsoft Corporation in the United States
and/or other countries.
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/
EC.
Please inform yourself about the local separate
collection system for electrical and electronic
products.
The USB-IF Logos are trademarks of Universal
Serial Bus Implementers Forum, inc.
Recording and playback of material might
require consent. See Copyright Act 1956 and
The Performer’s Protection Acts 1958 to 1972.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste. Correct disposal of
your old product helps to prevent potential
negative consequences for the environment and
human health.
The making of unauthorized copies of copy-
protected material, including computer
programs, files, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal offence.
This equipment should not be used for such
purposes.
Your product contains batteries covered by
the European Directive 2006/66/EC, which
cannot be disposed with normal household
waste.Please inform yourself about the local
rules on separate collection of batteries
This apparatus includes these labels:
EN 13
Class II equipment symbol
This symbol indicates that the apparatus has a
double insulation system.
14 EN
Specifications are subject to change without notice
© 2012 Koninklijke Philips Electronics N.V.
All rights reserved.
AZ1837_12_UM_V2.1
|