Petsafe Electric Pet Fence PIF 300 User Manual

Model Number  
PIF-300  
wireless  
pet containment system  
operating and training guide  
Please read thIs eNtIre guIde beFore begINNINg  
 
These steps will help keep your pet safe and comfortable. Millions of pets are comfortable while they wear  
stainless steel contacts. Some pets are sensitive to contact pressure. You may find after some time that  
your pet is very tolerant of the collar. If so, you may relax some of these precautions. It is important to  
continue daily checks of the contact area. If redness or sores are found, discontinue use until the skin has  
fully healed.  
You may need to trim the hair in the area of the Contact Points. Never shave the dog’s neck; this may lead  
to a rash or infection.  
Always remove your dog’s Receiver Collar before performing any Transmitter testing.  
The Receiver Collar should not be on your dog when the system is tested. Your pet may receive an  
unintended correction.  
The Boundary Width of the system must be tested whenever an adjustment is made to the containment  
field to prevent unintended corrections to your pet.  
If you use a collar and leash for training, be sure the extra collar does not put pressure on the contact  
points.  
Never remove power from the system when the collar is on the pet. This may activate the Receiver Collar.  
®
Radio Systems Corporation recommends the use of an Uninterruptible Power Supply (UPS) for use with  
your wireless fence. Should the power go out at your home, your pet will be unprotected. Power outages  
can be unpredictable, and the use of a UPS will provide you with some time to properly restrain your pet.  
In rare instances, if your pet is near the boundary at the time when the power fails, it is possible that your  
pet will receive a correction. This correction will stop after a 30 second timeout period has been reached.  
This is due to the operation of the collar: the collar is activated by the absence of the containment signal.  
While results will vary depending on the UPS manufacturer’s specifications the following are typical  
examples to guide your choice of UPS:  
Using a 400 VA UPS a consumer should expect 3 hours of backup time.  
Using a 900 VA UPS a consumer could expect 8 hours of backup time.  
If settings below maximum fence size are used, additional backup time will result. At minimum fence size  
settings backup time may be more than two times the backup time estimated at maximum fence size.  
To prevent an unintended correction, after the Boundary Flags have been placed, be sure to set the static  
correction on the Receiver Collar back to level 1 tone only.  
Do not place anything on the top of the Transmitter or cover any ventilation holes. This may overheat the  
Transmitter and cause early transmit failure.  
Do not place Transmitter in a closet or any other confined, unventilated area.  
3
 
®
Thank you for choosing PetSafe brand. You and your pet deserve a companionship  
that includes memorable moments and a shared understanding together. Our products  
and training tools promote a lifestyle of protection, teaching, and love — essentials that  
influence memories for a lifetime. If you have any questions about our products or training  
at 1-800-732-2677.  
To get the most protection out of your warranty, please register your product within 30 days  
full warranty and should you ever need to call the Customer Care Center, we will be able to  
®
help you faster. Most importantly, PetSafe will never give or sell your valuable information  
Table of Contents  
Components...................................................................................................................5  
Other Items You May Need ...........................................................................................5  
How the System Works ..................................................................................................6  
Key Definitions ...............................................................................................................6  
Operating Guide..........................................................................................................7  
Set Up the Transmitter.................................................................................................7  
Prepare the Receiver Collar.........................................................................................7  
Battery Contact Verification.........................................................................................8  
Adjust the Pet Area to Desired Size ............................................................................9  
Transmitter Range Chart............................................................................................10  
Place the Boundary Flags ..........................................................................................10  
Fit the Receiver Collar ...............................................................................................11  
Training Guide ...........................................................................................................12  
Be Patient With Your Pet ...........................................................................................12  
Day 1 - Boundary Awareness.....................................................................................13  
Days 2 thru 4 - Continue Boundary Awareness .........................................................14  
Days 5 thru 8 - Distraction Phase...............................................................................14  
Days 9 thru 14 - Unleashed Supervision....................................................................15  
Days 15 thru 30 - Pet Monitoring ..............................................................................15  
Taking Your Pet Out of the Pet Area............................................................................15  
Wireless - To - Go.........................................................................................................16  
Accessories...................................................................................................................16  
Frequently Asked Questions...................................................................................16  
Troubleshooting ........................................................................................................18  
Re-synchronize the System ..........................................................................................20  
Terms of Use and Limitation of Liability ......................................................................20  
Compliance ..................................................................................................................21  
Customer Care International........................................................................................21  
Perchlorate Battery ......................................................................................................21  
Mounting Template......................................................................................................24  
4
1-800-732-2677  
 
Components  
Receiver  
Collar  
Transmitter  
Battery  
(PetSafe RFA-67)  
®
Power  
PM  
u
m
o
de  
l
F-30  
N
I
be  
0 r  
Adapter  
Test Light  
Tool  
pe  
wi  
t
cont  
o
r
e
a
le  
in  
in  
P
p
L
e
inment  
E
A
S
r
a
t
s
E
ing  
R
E
s
A
a
n
d
D
T
H
t
IS  
r
a
E
s
N
T
ys  
IR  
E
g
g
GU  
u
id  
t
em  
ID  
e
E
B
E
F
OR  
E
B
E
GI  
N
N
IN  
G
Boundary Flags - 50  
Operating and  
Training Guide  
Other Items You May Need  
Pliers  
Scissors  
Lighter  
Drill & mounting hardware  
Tape measure  
Non-metallic collar and leash  
®
Want professional installation help? Invisible Fence Brand installers will come to your home and install your  
®
new PetSafe System for an additional cost. Contact your local dealer at 1-877-866-DOGS(3647) or visit our  
5
 
How the System Works  
®
®
The PetSafe Wireless Pet Containment System has been proven safe, comfortable, and effective for pets over  
8 pounds. The system works by transmitting a radio signal up to 90 feet in all directions. You temporarily define  
the Pet Area with Boundary Flags for a visual aid in training your pet. Your pet wears a Receiver Collar with  
Contact Points that touch his neck, and, once trained, is allowed to roam freely in the Pet Area. When your pet  
reaches the Boundary Zone, the Receiver Collar gives a warning beep before delivering a safe Static Correction  
through the Contact Points to get his attention until he returns to the Pet Area.  
Key Definitions  
Transmitter: Transmits the radio signal and is the center  
of the Pet Area.  
Pet Area: Distance from the Transmitter where your pet  
can roam freely.  
Boundary Zone: 2 to 3 foot wide area outside  
the Pet Area where your pet’s Receiver Collar will  
begin to beep and then begin to deliver a Static  
Correction. The correction will start in the Boundary  
Zone and continue anywhere beyond the Pet Area.  
Note: The Receiver Collar is equipped with a safety  
time-out feature that will stop correcting after 30  
seconds if your pet remains outside the Pet Area.  
Receiver Collar: Receives the radio signal from  
the Transmitter.  
Correction Level Button: Adjusts the level of Static  
Correction your pet receives outside the Pet Area.  
Receiver Indicator Light: Indicates the level of  
correction at which the Receiver Collar is set. This light  
also serves as a low battery indicator.  
Note: In many  
neighborhoods,  
nearby property  
lines may limit  
how large the  
Pet Area can be.  
Transmitter  
PET AREA  
Maximum  
90 ft. range  
(45 average steps)  
Contact Points: Deliver the safe Static Correction when  
your pet moves into the Boundary Zone.  
Power Jack: Where the Power Adapter plugs into the  
Transmitter. The Transmitter is powered by a standard  
120-volt outlet.  
Boundary Switch: Adjust according to the size of the Pet Area desired. Note: Adjusting the  
switch does not change the level of Static Correction on the Receiver Collar.  
Power Light: Indicates when the Transmitter is on.  
Boundary Control Dial: Adjusts the distance from the Transmitter to the Boundary Zone.  
Note: Adjusting the dial does not change the level of Static Correction on the Receiver Collar.  
Transmitter  
Receiver Collar  
Receiver  
Battery  
Indicator  
Light  
Power Jack  
Boundary Switch  
Power Light  
Boundary Control Dial  
On/Off Switch  
Washers  
Contact Points  
6
1-800-732-2677  
 
Operating Guide  
Step Set Up the Transmitter  
Important: You may need to move the Transmitter several times before determining the final location.  
The Transmitter is located at the exact center of the Pet Area. Place the Transmitter:  
At least 2 feet above the floor located on the ground floor of your home.  
In a dry, well ventilated, protected area.  
In an area where temperatures do not fall below freezing (e.g., garage, shed, closet).  
On a non-metal table or mount on a wall (1A). A mounting template is included on the back of  
this guide.  
At least 3 feet from large metal objects, as these items may reduce the size and shape of your  
Pet Area (1B).  
1
Boundary  
To maximize your Pet Area, make  
Switch  
1B  
1C  
1A  
Low  
sure the Boundary Switch is on  
“High” and the Boundary Control  
Dial is set to “8” (1C). Plug Power  
Adapter into Power Jack and  
standard 120-volt outlet. Turn the  
Transmitter on.  
High  
Powe  
r
3ft.  
Wall  
Mount  
Y
7
8
CONTROL  
BOUNDAR  
Tabletop  
8
Step Prepare the Receiver Collar  
Your Receiver Collar comes with short Contact Points. Long Contact Points for  
pets with long or thick hair are available through our Customer Care Center at  
1-800-732-2677. Tighten the Contact Points using the Test Light Tool (2A) one-half  
2A  
2
turn beyond finger tight. Check the tightness weekly.  
To Insert and Remove the Receiver Collar Battery  
Note: Do not install the battery while the Receiver Collar is on your pet.  
®
This Receiver Collar utilizes a replaceable PetSafe battery (RFA-67). This unique  
battery is designed to make battery replacement easier and increase water  
protection.  
2B  
2C  
To insert the battery, align the symbols on the battery (arrow) and Receiver  
Collar (triangle) (2B). Use the edge of the Test Light Tool (2B) to turn the  
battery clockwise until the arrow lines up with the lock symbol on the housing.  
To remove the battery, turn the battery counter-clockwise using the edge of  
the Test Light Tool (2C). DO NOT attempt to cut into or pry open the battery.  
Be sure to discard the used battery properly.  
®
A replacement PetSafe battery (RFA-67) can be found at many retailers.  
Contact the Customer Care Center at 1-800-732-2677 or visit our web site at  
7
 
To Set the Static Correction Level  
Read all steps before attempting to set  
the Static Correction Level.  
2E  
2D  
1. Remove the clear plastic cover with the  
edge of the Test Light Tool to expose  
the Correction Level Button (2D).  
2. With the battery installed, press the  
Correction Level Button and release  
when the Receiver LED Indicator Light  
lights up (2E).  
3. The Receiver LED Indicator Light will  
emit a series of flashes representing  
the Static Correction Level.  
4. Increase the Static Correction Level by  
pressing and releasing the Correction  
Level Button within 5 seconds of the  
previous series of flashes.  
5. After setting the Static Correction Level, replace the cover to protect the Correction Level Button.  
The Static Correction levels increase in strength from 1 to 6. Pushing the Correction Level Button  
while the Receiver Collar is on level 6 will cause the Receiver Collar to revert to level 1. Refer to the  
Function and Response Table to choose the Static Correction level that best fits your pet.  
The Receiver Indicator Light acts as a low battery indicator. The light will flash every 4 to 5 seconds  
when battery replacement is required.  
Battery Contact Verification  
Remove Receiver Collar from your pet. Press the button and verify that the LED light illuminates. If  
the LED light does not come on remove the battery. Locate the metal tabs in the battery well. Gently  
lift the tabs to ensure that the battery will make good contact. Replace the battery into the Receiver  
Collar. Press the button and check that the LED light illuminates.  
Function and Response Table  
Static  
Correction  
Level  
Indicator Light  
Response  
Receiver Collar Function  
Temperament of Pet  
1 Flash  
1
2
3
4
5
6
No Static Correction, Tone Only  
Low Static Correction  
Initial Training Mode  
Timid  
2 Flashes  
3 Flashes  
4 Flashes  
5 Flashes  
6 Flashes  
Medium-Low Static Correction  
Medium Static Correction  
Medium-High Static Correction  
High Static Correction  
Timid or Average  
Average Energy  
Average or High Energy  
High Energy  
Flashes once every  
4 to 5 seconds  
Indicates Low Battery  
Over Correction Protection  
If your pet enters the Boundary Zone or continues anywhere beyond the Pet Area, this feature limits  
the Static Correction duration to 30 seconds.  
In the unlikely event that your pet leaves the Pet Area, he will not receive a Static Correction upon  
return to the Pet Area.  
8
1-800-732-2677  
 
Step Adjust the Pet Area to Desired Size  
Make sure the entire Pet Area lies within your property boundaries (3A).  
3A  
Always start determining the Boundary Zone at the shortest distance from  
Transmitter. Place the Boundary Switch on “Low” if the Boundary Zone will  
be less than 45 feet from the Transmitter.  
3
Make sure the Receiver Collar battery is properly installed, the Static  
Correction level is set at 2 or greater, and the Test Light Contacts are  
touching the Contact Points (3B).  
Pet  
Area  
Note: If your next-door neighbor has an In-Ground containment system, see  
Troubleshooting section page 19.  
Test Light Instructions  
1. Set the Correction Level to 2 or above.  
2. Hold the Test Light Contacts to the Contact Points.  
3. Walk toward the Boundary Zone holding the Receiver collar at your pet’s  
neck level until the Test Light flashes.  
3B  
Save Test Light for future testing.  
Note: If the Test Light does not flash, install a new battery and re-test.  
If Test Light still does not flash, contact the Customer Care Center at  
1-800-732-2677.  
To maximize your Pet Area, make sure the Boundary Switch is on “High” and  
the Boundary Control Dial is set to “8”. Plug Power Adapter into Power Jack  
and standard 120-volt outlet.  
Two-Person Method  
Hold the Receiver Collar at your pet’s neck height (3C) with logo side facing  
away from the Transmitter and Contact Points facing upwards. Walk to the edge  
of the desired Pet Area. Facing away from the Transmitter, hold the Receiver  
Collar at the edge of the desired Pet Area (3D).  
Starting with the Boundary Control Dial set to “8”, have a second person  
turn the dial down SLOWLY. When the Receiver Collar starts to beep, tell the  
person to stop turning the Boundary Control Dial. Record your settings below  
for future reference.  
One-Person Method  
3C  
3D  
Measure the shortest distance from the desired Boundary  
Zone to the Transmitter. Find the distance on the Transmitter  
Range Chart on page 10 and set the Boundary Switch and  
Boundary Control Dial. Hold the Test Light Contacts to the  
Contact Points (3B). Take the Receiver Collar to the Boundary  
Zone with the logo side facing away from the Transmitter and  
Contact Points facing upwards (3C). Hold the Receiver Collar at  
your pet’s neck level (3D) until the Receiver Collar beeps and  
the Test Light flashes. If the Receiver Collar beeps before or  
after the desired Boundary Zone, return to the Transmitter and  
adjust the Boundary Control Dial. Repeat this process until  
the Receiver Collar is beeping at the desired location. Record  
your settings on page 10 for future reference.  
Pet  
Area  
9
 
Transmitter  
Range Chart Record Your Settings  
Boundary Boundary Boundary  
Final Boundary  
Switch Setting  
(HIGH or LOW)  
Final Boundary Receiver  
Control  
Dial  
Switch  
LOW  
Switch  
HIGH  
Control Dial  
Position (1-8)  
Static Cor-  
rection  
Position  
Level (1-6)  
1
2
3
4
5
6
7
8
5-10 ft.  
5-10 ft.  
5-10 ft.  
5-10 ft.  
Home  
Camping  
Vacation  
Other  
15-20 ft.  
20-25 ft.  
25-30 ft.  
35-40 ft.  
40-45 ft.  
40-45 ft.  
25-35 ft.  
42-55 ft.  
55-65 ft.  
75-85 ft.  
85-90 ft.  
85-90 ft.  
Note: These distances are approximate.  
Step Place the Boundary Flags  
The Boundary Flags are visual reminders for your pet of where  
the Boundary Zone is located. The Receiver Collar will activate  
within 2 to 3 feet of the Boundary Flags.  
4A  
4B  
4
1. Using the Test Light, with the Static Correction Level set at 2  
or greater, hold the Receiver Collar at your pet’s neck height  
with logo side facing away from the Transmitter.  
2. Walk towards the Boundary Zone until the Receiver Collar  
beeps and the Test Light flashes. (4A).  
3. Place a Boundary Flag in the ground (4B).  
4. Walk back into the Pet Area until the beeping stops.  
5. Repeat this process around the Boundary Zone until it is marked with Boundary Flags every 10 feet.  
The Boundary Flags may be in different parts of the Boundary Zone and may not be in a line. The  
Boundary Zone is 2 to 3 feet wide.  
10  
1-800-732-2677  
 
Step Fit the Receiver Collar  
Important: The proper fit and placement of your Receiver Collar is important for effective training. The  
Contact Points must have direct contact with your pet’s skin on the underside of his neck.  
Please read and follow the instructions in this manual. Proper fit of the collar is important. A  
5
collar worn for too long or made too tight on the pet’s neck may cause skin damage. Ranging  
from redness to pressure ulcers; this condition is commonly known as bed sores.  
Avoid leaving the collar on the dog for more than 12 hours per day.  
When possible reposition the collar on the pet’s neck every 1 to 2 hours.  
Check the fit to prevent excessive pressure; follow the instructions in this manual.  
Never connect a lead to the electronic collar; it will cause excessive pressure on the  
contacts.  
When using a separate collar for a lead, don’t put pressure on the electronic collar.  
Wash the dog’s neck area and the contacts of the collar weekly with a damp cloth.  
Examine the contact area daily for signs of a rash or a sore.  
If a rash or sore is found, discontinue use of the collar until the skin has healed.  
If the condition persists beyond 48 hours, see your veterinarian.  
For additional information on bed sores and pressure necrosis, please visit our website.  
These steps will help keep your pet safe and comfortable. Millions of pets are comfortable  
while they wear stainless steel contacts. Some pets are sensitive to contact pressure. You  
may find after some time that your pet is very tolerant of the collar. If so, you may relax some  
of these precautions. It is important to continue daily checks of the contact area. If redness or  
sores are found, discontinue use until the skin has fully healed.  
You may need to trim the hair in the area of the Contact Points. Never shave the dog’s neck;  
this may lead to a rash or infection.  
To assure a proper fit, please follow these steps:  
5A  
1. Make sure that the battery is not installed in the Receiver Collar.  
2. Start with your pet standing comfortably (5A).  
3. To make it easier to hear the warning tone, place the Receiver Collar on your  
pet with the logo side of Receiver facing up.  
4. Center the Contact Points underneath your pet’s neck, touching the skin.  
You may need to trim the hair in the area of the Contact Points.  
Never shave the dog’s neck; this may lead to a rash or infection.  
5. Check the tightness of the Receiver Collar by inserting  
5B  
one finger between the end of a Contact Point and your  
pet’s neck. The fit should be snug but not constricting  
(5B).  
6. Allow your pet to wear the collar for several minutes  
then recheck the fit. Check the fit again as your pet  
becomes more comfortable with the Receiver Collar.  
7. Trim the collar as follows (5C):  
a. Mark the desired length of the Receiver Collar  
with a pen. Allow for growth if your pet is young or  
grows a thick winter coat.  
b. Remove the Receiver Collar from your pet and cut  
5C  
off the excess.  
c. Before placing the Receiver Collar back onto your  
pet, seal the edge of the cut collar by applying a  
flame along the frayed edge.  
8. Put battery in Receiver Collar.  
11  
 
To Re-Thread the Collar  
Slide Buckle  
The slide buckle prevents the collar from  
becoming loose around your pet’s neck.  
Ridges  
The ridges must be facing up; the collar  
will slip if it is not properly threaded.  
Training Guide  
Be Patient With Your Pet  
®
Important: Proper training of your pet is essential to the success of the PetSafe Wireless  
®
Pet Containment System . Read this section completely before beginning to train your pet.  
®
®
Remember that the PetSafe Wireless Pet Containment System is not a solid barrier.  
Have fun with your pet throughout the training process. Training should be  
S
M
T
W
T
F
S
6
7
1
8
2
3
4
5
fun, fair, rm and consistent.  
Train for 10 to 15 minutes at a time. Don’t try to do too much too  
quickly. More-frequent short sessions are better than less-frequent  
longer sessions.  
We suggest a minimum of 14 days of training. Depending on your pet  
and how he learns, the training could take more or less time.  
If your pet shows signs of stress, slow down the training schedule, add  
additional days of training, or increase the amount of play time with your  
pet in the Pet Area. Common stress signals include:  
-Pet pulling on leash toward the house  
13 14  
20 21  
9
10 11 12  
15 16 17 18 19  
22 23 24 25 2
0
8  
45  
15  
29 30 31  
min.  
30  
-Ears tucked  
-Tail down  
-Body lowered  
-Nervous / frantic movement or stiffening of pet’s body  
Your pet must be completely comfortable near the Boundary Flags at the end of every training  
session. Spend at least 5 minutes of “play time” at the completion of each session within 10 feet  
of the Boundary Flags.  
Finish each training session on a positive note with lots of praise and play.  
Remove the Receiver Collar after each training session.  
Be sure to contain your pet by another means during the training period (e.g. pen, tie-out, leash,  
etc.).  
During training, if you need to take your pet out of the Pet Area, remove the Receiver Collar and  
either pick your pet up or put him in the car to pass out of the Pet Area.  
Even if you think your pet is responding well to the training, complete the entire training.  
Reinforcement is important!  
12  
1-800-732-2677  
 
PhaseDay 1 - Boundary Awareness  
Tone Only Training Mode  
Perform three sessions on day 1, each training session lasting 10-15 minutes.  
Goal:  
1
To have your pet learn that the Boundary Flags and warning beep from the Receiver Collar define  
the new Pet Area.  
Setup:  
Program the Static Correction Level on the Receiver Collar to Level 1 Tone Only training mode.  
Put a separate non-metallic collar on your pet’s neck ABOVE the Receiver Collar and attach a  
leash.  
Be sure the extra collar does not put pressure on the Contact Points.  
Have tiny pieces of treats that your pet will find desirable available (hot dogs or lunch meat work  
well).  
Have your pet’s favorite play toy available.  
Steps:  
1. Begin by walking your pet on a leash in the Pet Area. Calmly praise and talk to your pet.  
2. Move toward the Boundary Flags (1A). Keep your mood happy.  
3. With full control of your pet on a leash, walk to the flags. As your pet enters the Boundary Zone, the  
Receiver Collar will begin to tone (1B). Allow your pet to stay in the Boundary Zone for up to 2 seconds  
then gently help him back into the Pet Area (1C). Immediately praise and offer your pet a treat as he  
enters the Pet Area, even if you have helped with the leash.  
4. Repeat this process at the same Boundary Flag until your pet resists going into the Boundary  
Zone.  
5. Aim to master 3-4 Boundary Flags per session. Make this FUN! Praise if your pet quickly retreats  
or resists going into the Boundary Zone.  
1A  
1B  
1C  
13  
 
PhaseDays 2 thru 4 - Continue Boundary  
Awareness  
Introduction to Static Correction  
2
Perform three sessions per day, each lasting 10-15 minutes.  
Goal:  
To train your pet to stay in the Pet Area and respect the boundary.  
Setup:  
Program the Static Correction Level on the Receiver Collar to Level 2.  
Put a separate non-metallic collar on your pet’s neck ABOVE the Receiver Collar and attach a leash.  
Be sure the extra collar does not put pressure on the Contact Points.  
Have tiny pieces of treats available (hot dogs or lunch meat work well).  
Have your pet’s favorite play toy available.  
Steps:  
1. Repeat steps 1-5 in Phase One.  
2. If your pet does not respond to the Static Correction, confirm that the Receiver Collar is fitting  
properly according to Step 5 on page 11.  
3. If the Receiver Collar is fitted properly and your pet does not respond to the Static Correction,  
increase the Static Correction Level by 1. Watch for slight reactions at first such as ears up, head  
turned, looking at the ground.  
4. Stay at the same flag until your pet resists going into the Boundary Zone.  
PhaseDays 5 thru 8 - Distraction Phase  
Perform three training sessions per day, each lasting 10 to 15 minutes.  
Goal:  
To train your pet to stay within the Pet Area with distractions outside of the Pet Area.  
3
Setup:  
Program the Static Correction Level on the Receiver Collar to level 2 or higher depending on the  
reaction results from days 2 thru 4.  
Put a separate non-metallic collar on your pet’s neck ABOVE the Receiver Collar and attach a leash.  
Be sure the extra collar does not put pressure on the Contact Points.  
Have tiny pieces of treats available (hot dogs or lunch meat work well).  
Have your pet’s favorite play toy available.  
Create distractions to tempt your pet to enter the Boundary Zone, such as:  
-Have a family member cross from inside the Pet Area to outside of it.  
-Throw a ball or treat outside of the Pet Area.  
-Have a neighbor walk their pet outside of the Pet Area.  
Gradually increase distraction level. Never coax or call your pet out of the Pet Area.  
Steps:  
1. With full control of your pet on a leash, have the distraction presented.  
2. If your pet does not move toward the distraction, praise and offer a treat.  
3. If your pet does react to the distraction, allow him to go into the Boundary Zone.  
4. Help your pet back into the Pet Area if he does not turn back after 2 seconds.  
5. Treat and praise your pet anytime he comes back into the Pet Area with or without help.  
6. Repeat this process with other distractions. Use other family members during this process.  
7. If your pet does not respond to the Static Correction, confirm that the Receiver Collar is fitting  
properly according to Step 5 on page 11.  
8. If the Receiver Collar is fitted properly and if your pet does not respond to the Static Correction,  
increase the Static Correction Level by 1.  
14  
1-800-732-2677  
 
PhaseDays 9 thru 14 - Unleashed Supervision  
Training sessions should start at 10-15 minutes, gradually increasing to  
over an hour.  
Your pet is ready for this step only when he clearly avoids the entire  
4
Boundary Zone, regardless of any distractions or temptations. During this  
step, do not leave your pet unattended.  
Goal:  
To give your pet free run of the Pet Area off the leash.  
Setup:  
Adjust the Receiver Collar to the permanent setting appropriate for your  
pet.  
Steps:  
1. Enter the Pet Area with your pet wearing the Receiver Collar.  
2. Walk around the yard and play with your pet, staying within the Pet Area at all times.  
3. Preoccupy yourself with another task in the yard while watching your pet.  
4. Should your pet escape, take the Receiver Collar off and lead him back into the Pet Area.  
PhaseDays 15 thru 30 - Pet Monitoring  
Your pet is ready to run! Check in on your pet at regular intervals.  
Note: After you are satisfied your pet’s training is complete, remove every other Boundary Flag every  
4 days until all flags are removed. Save Boundary Flags for future use.  
5
Taking Your Pet Out of the Pet Area  
Important: Remove the Receiver Collar and leave it in the Pet Area.  
Once your pet learns the Boundary Zone, he will be reluctant to cross it for walks or car rides.  
Option 1: Replace the Receiver Collar with a regular collar. Put your pet in a car  
that is within the Pet Area and drive him out of the Pet Area.  
Option 2: Replace the Receiver Collar with a regular collar and leash. Walk  
your pet out of the Pet Area while giving a command such as “OK” at a  
specific place of the Boundary Zone (the end of your driveway, sidewalk, etc.).  
Always leave the Pet Area with a leash at this place and your pet will associate  
leaving the Pet Area only on a leash, only at this place, and only with a person.  
You may initially need to convince your pet to leave the Pet Area with a food  
treat and lots of praise.  
Note: You may also carry your pet out of the Pet Area.  
Congratulations!  
You have now  
successfully completed  
the training program.  
15  
 
Wireless - To - Go  
®
®
Your PetSafe Wireless Pet Containment System is completely portable. Follow the set-up procedures (steps  
1 through 4) wherever you wish to have containment of your pet. Reestablish the Pet Area and mark it with  
Boundary Flags so your pet knows his Boundary Zone. Note: If setting up in a metal building or vehicle, the  
maximum size of the Pet Area may be reduced. Be sure to remove the Receiver Collar battery before turning  
off the Transmitter. If you want to power the Transmitter from a car or other DC source, use an inverter rated  
for 50 watts or more.  
Accessories  
®
®
To purchase additional accessories for your PetSafe Wireless Pet Containment System , contact the Customer  
Component  
Part Number  
RFA-67D-11  
PIF-275-19  
RFA-374  
Battery - two pack  
Extra Wireless Containment System Receiver Collar  
Power Adapter  
Replacement Collar  
Extra Flags  
RFA-449  
RFA-2  
Extra Wireless Transmitter  
Accessory Pack  
IF-100  
RFA-281  
Stay + Play Wireless Fence Receiver Collar  
PIF00-12918  
PIF00-13210  
RFA-463  
Stay + Play Wireless Fence Transmitter and Adapter  
Stay + Play Receiver Collar Charger  
Frequently Asked Questions  
Is the Receiver Collar waterproof?  
Yes. When changing the battery, be sure to keep the battery area  
free from dirt and debris.  
®
Will the PetSafe Wireless Pet  
You can use another Wireless Transmitter with overlapping  
boundaries of at least 5-10 feet to increase the size of the Pet Area.  
®
Containment System cover a larger  
circle than 180 feet across?  
Will a sloping yard or hills affect the  
Pet Area?  
The Transmitter signal extends 90 feet in all directions. A sloping  
yard or a yard with hills can cause the Pet Area to appear less or  
more than expected. Consider repositioning the Transmitter to  
maximize your Pet Area.  
Can I use more than one Receiver  
Collar with the Wireless System?  
Yes. There is no limit to the number of pets you can contain with  
the Wireless System. You must purchase an additional Wireless Pet  
Containment Receiver Collar for each pet. Contact the Customer  
net to locate a retailer near you.  
Will the Wireless System keep other  
pets out of my yard?  
No. The Wireless System is only effective on pets who wear the  
Receiver Collar.  
Is there a hand-held remote  
Transmitter that will work with the  
Wireless System Receiver Collar?  
Is there a smaller Receiver Collar or  
another compatible Receiver Collar  
that I can use with the Wireless  
Transmitter?  
No. You would need to purchase a separate Remote Training  
System. Contact the Customer Care Center at 1-800-732-2677 or  
Yes. The Stay + Play Wireless Fence Receiver Collar is sized for  
pets weighing over 5 pounds with neck sizes from 6 inches to  
23 inches. A Receiver Collar charger is required for this  
Receiver Collar.  
16  
1-800-732-2677  
 
If I have a question about my Wireless Contact the Customer Care Center at 1-800-732-2677 or visit our  
System or need replacement parts,  
where can I get answers or service?  
Can I use the Wireless System on an  
aggressive pet?  
We do not recommend using any electronic training devices on  
aggressive pets. If you are unsure if your dog is aggressive, please  
consult your veterinarian or a certified trainer.  
Can I use the Wireless System on a cat? The Wireless System can be used as long as the cat can  
comfortably wear the Receiver Collar.  
What happens if the power goes out? The Wireless System is designed to recognize power outages and  
shuts down without activating the Receiver Collar. However, if your  
pet is near the Boundary Zone during the power failure, he may  
receive a Static Correction.  
What can happen if I turn off or  
unplug the Transmitter power?  
If your dog is wearing the Receiver Collar, he may receive an  
unintended correction. Always remove your dog’s Receiver Collar  
before removing power from the Transmitter or before performing  
any Transmitter testing.  
What if I lose the clear plastic cover  
for the Correction Level Button?  
The clear plastic cover prohibits the Static Correction Level from  
accidentally being changed and also helps keep the Receiver  
waterproof. Contact the Customer Care Center at 1-800-732-2677  
for a replacement.  
If my pet leaves the Pet Area, how  
long will he be corrected?  
Your pet will receive Static Correction as long as he is outside the  
Pet Area, for up to 30 seconds. The Receiver Collar has a safety  
time-out to stop correcting and toning after 30 seconds until it is  
returned to the Pet Area.  
How often do I need to replace the  
Receiver Collar battery?  
Battery life depends on how frequently your pet tests the Boundary  
Zone. The Receiver Indicator Light acts as a low battery indicator,  
flashing every 4 to 5 seconds when replacement is required.  
Can I place the Receiver on another  
collar?  
Yes. You may use any non-metallic collar. Make 2 holes in the collar  
to attach the Receiver. Use the collar in the kit as a template to  
locate the holes on the new collar.  
Do I need to perform maintenance on Check your pet’s neck daily for irritation from the Contact Points.  
my Wireless System?  
Check the Contact Points on the Receiver Collar weekly to make  
sure they are tight and clean.  
Check the fit of the Receiver Collar weekly.  
The Receiver Indicator Light acts as a low battery indicator, ashing  
every 4 to 5 seconds when replacement is required.  
How do I know the battery in the  
Receiver Collar is still working?  
Take the Receiver Collar off your pet and walk into the Boundary  
Zone. The Receiver Collar should tone. If not, replace the battery.  
Will vehicles, buildings and landscape Yes. Placing the Transmitter inside a metal building can reduce the  
features (trees, shrubs, etc.) affect the  
performance of the Wireless System?  
maximum range of the Wireless System.  
Parking a vehicle within the Pet Area, can reduce the range of the  
system and cause your pet to receive a Static Correction where it  
otherwise would not if the vehicle was not there.  
Fixed large metal objects such as metal sheds can affect the signal  
by reducing the maximum range of the system at the location of  
the object. As a result, your pet may receive a Static Correction.  
What do I do if my pet’s neck  
becomes red and irritated?  
This condition is due to the Contact Points irritating the skin.  
Discontinue use of the Receiver Collar for a few days. If the  
condition persists beyond 48 hours, see your veterinarian. Once  
the skin returns to normal, replace the Receiver Collar and monitor  
the skin condition closely.  
Can I attach a leash to the Receiver  
Collar?  
No. This can result in pulling the Contact Points too tightly against  
your pet’s neck. Attach a leash to a separate, non-metallic collar  
positioned above the Receiver Collar.  
Why does my Receiver Collar have a  
tone only mode?  
The tone only mode can be used in training your pet to his  
boundary or for well-trained pets that no longer require Static  
Correction.  
17  
 
Troubleshooting  
The Receiver Collar is not beeping  
when setting up the Boundary Zone.  
The tone may be difficult to hear in a noisy environment.  
Use Test Light as explained in the “Test Light Instructions”  
section, and use it to determine the location of Boundary Zone.  
Check that the Transmitter is set up according to directions  
and install a new battery while standing within 5-10 feet of the  
Transmitter.  
Re-Synchronize the System. (Page 20)  
The Receiver Collar is not beeping or Check that the Transmitter is plugged into a working 120-volt  
administering a Static Correction.  
outlet, turned on, the Power Light is on, and the Transmitter  
controls are set at your desired settings.  
Check Receiver battery to make sure it is installed properly.  
When replacing the battery, do so while standing within 5-10 feet  
of the Transmitter.  
Re-Synchronize the System. (Page 20)  
The Receiver Collar is beeping  
everywhere.  
Check that the Transmitter is plugged into a working standard  
120-volt outlet, turned on, the Power Light is on, and the  
Transmitter controls are set at your desired settings.  
Bring Receiver Collar while standing within 5-10 feet of the  
Transmitter to reset.  
Re-Synchronize the System. (Page 20)  
The Receiver Collar is beeping inside It is recommended to remove the Receiver Collar from your pet  
the house.  
when indoors to avoid activation of the Receiver Collar.  
Make sure the Transmitter is on and set up according to the  
directions.  
Ensure the entire house is within the Pet Area. The Transmitter  
may need to be moved to adjust the Pet Area to include the  
entire house.  
If relocating the Transmitter, remove the Receiver Collar from your  
pet before turning the Transmitter off.  
My pet is receiving a Static  
Correction in his metal crate.  
The Receiver Collar activates when it loses the Transmitter signal.  
The metal crate may block the Transmitter signal which causes the  
Receiver Collar to activate.  
Remove the Receiver Collar from your pet when placing him in his  
metal crate.  
The Boundary Zone seems to  
fluctuate.  
This is normal for the electro magnetic field of the Wireless System.  
The field may be affected by surrounding “electronic noise,” which  
can cause it to fluctuate up to 5%.  
Where the Receiver Collar activates is influenced by the speed and  
orientation of the Receiver Collar as your pet enters the Boundary  
Zone.  
The Receiver Collar activates in the  
middle of the yard.  
The Receiver Collar activates when it loses the Transmitter signal.  
This sometimes occurs if a large metal object is between the  
Receiver Collar and Transmitter, if the orientation of the Receiver  
Collar changes near the Boundary Zone, or if the surrounding  
“electronic noise” interferes with the signal. If this continues to  
occur, consider relocating the Transmitter and resetting the Pet  
Area.  
Re-Synchronize the System. (Page 20)  
18  
1-800-732-2677  
 
The Receiver Collar is beeping but  
my pet is not responding to the  
Static Correction.  
Make sure the Static Correction Level is set at 2 or above.  
Test the Receiver Collar with the Test Light.  
If the Test Light flashes, check the fit of the Receiver Collar.  
Trim your pet’s fur where the Contact Points touch the neck and/  
or purchase long Contact Points by contacting the Customer Care  
Center at 1-800-732-2677.  
Increase the Static Correction Level.  
Repeat training steps to reinforce training.  
My pet reacts strongly to the Static  
Correction and has become fearful.  
Lower the Static Correction Level.  
Make sure you are in control of the situation when your pet  
receives his first Static Corrections (have him on a leash attached  
to a separate, non-metallic collar) and lead him into the Pet Area  
and praise him. If your pet remains fearful, suspend training and  
start again the next day. Make sure to end all training sessions on a  
positive note with lots of praise and play.  
The Power Light is not on.  
Make sure the Transmitter On/Off Switch is on and the Power  
Adapter is plugged into the Transmitter and a working standard  
120-volt outlet.  
I was setting up the Pet Area and  
after I turned down the Boundary  
Control Dial, the Receiver Collar  
would no longer beep or correct.  
You may have turned the Boundary Control Dial down too quickly,  
causing the Receiver Collar to go into power-fail mode. This is a  
safety feature designed to protect your pet when power to the  
Transmitter goes out. With the Receiver Collar while standing  
within 5-10 feet of the Transmitter, turn the Boundary Control Dial  
to “8” and reset the Boundary Zone, making sure to turn the dial  
down slowly.  
My next-door neighbor has an  
In-Ground Containment System and  
the Receiver Collar does not activate  
near their property.  
Your neighbor’s In-Ground Fence signal may interfere with the  
operation of the Receiver Collar preventing activation close to  
their fence. To minimize the interference, reduce the size of the  
Pet Area or move the Transmitter away from the In-Ground Fence  
System.  
Adjust the Pet Area so that the Receiver Collar activates for at  
least 5 feet beyond the reduced Boundary setting when walking  
towards the In-Ground Fence.  
The Receiver Collar has injured my  
pet’s neck.  
Failing to follow the important safety information at the front of  
the Operating and Training Guide has caused pressure ulcers.  
Some descriptions of advanced pressure ulcers describe the  
sores as looking like burns on the dog’s neck. Be assured that  
electronic collars do not use enough energy to create electrical  
burns. The energy in an output pulse is only a few thousandths  
of a Joule; it is similar in nature to the static pulse that you may  
feel when getting out of your car. In some cases, pressure ulcers  
are described as chemical burns.The RFA-67 battery is sealed  
when installed in the Receiver Collar housing. This sealing makes  
it virtually impossible, without misuse or abuse, for your Receiver  
Collar battery to leak onto your pet’s neck. Please review and  
follow the important safety information on page 2, and the  
instructions in Step 5 under the heading “Fit the Receiver Collar”  
on page 11.  
19  
 
Re-synchronize the System  
1. Remove the Receiver Collar from your pet.  
2. Remove the battery from the Receiver Collar. Discharge all power by holding the correction level button  
down until the LED is no longer illuminated.  
3. At the transmitter, move the Boundary Switch from the low to the high position.  
4. Slowly adjust the Boundary Control Dial up to 8, down to 1 and then back to the #4 position.  
5. Standing within 5-10 feet of the Transmitter, reinsert the battery into the Receiver Collar.  
6. Test the Boundary and verify operation by walking out into the Pet Area until your Receiver Collar  
responds. (With the Transmitter set to 4, it should activate approximately 40-50 feet away).  
Once you are confident that the system is working, reset the Transmitter controls to the original setting.  
Terms of Use and Limitation of Liability  
1. Terms of Use  
This Product is offered to you conditioned upon your acceptance without modification of the terms,  
conditions and notices contained herein. Usage of this Product implies acceptance of all such terms,  
conditions, and notices.  
2. Proper Use  
This Product is designed for use with pets where training is desired. The specific temperament of your pet  
may not work with this Product. If you are unsure whether this is appropriate for your pet, please consult  
your veterinarian or certified trainer.  
3. No Unlawful or Prohibited Use  
This Product is designed for use with pets only. This pet training device is not intended to harm, injure or  
provoke. Using this Product in a way that is not intended could result in violation of Federal, State or local  
laws.  
4. Limitation of Liability  
®
In no event shall Radio Systems Corporation be liable for any direct, indirect, punitive, incidental, special  
or consequential damages, or any damages whatsoever arising out of or connected with the use or misuse  
of this Product. Buyer assumes all risks and liability from the use of this Product.  
5. Modification of Terms and Conditions  
®
Radio Systems Corporation reserves the right to change the terms, conditions and notices under which  
this Product is offered.  
20  
1-800-732-2677  
 
Compliance  
USA/Canada  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant  
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful  
interference when the equipment is operated in a residential environment. This equipment generates, uses, and  
can radiate radio frequency energy and, if not installed and used in accordance with the instruction guide, may  
cause harmful interference to radio communications. However, there is no guarantee that interference will not  
occur in a practical installation. If this equipment causes harmful interference to radio or television reception,  
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
Relocate the interfered receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Contact the Customer Care Center at 1-800-732-2677.  
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)  
This device may not cause harmful interference, and (2) this device must accept any interference received,  
including interference that may cause undesired operation.  
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the  
following two conditions: (1) this device may not cause interference, and (2) this device must accept any  
interference, including interference that may cause undesired operation of the device.  
®
Unauthorized changes or modifications to the equipment, not approved by Radio Systems Corporation,  
could result in not meeting compliance with FCC or IC regulations and void the user’s authority to operate the  
equipment.  
Australia  
This device complies with the applicable EMC requirements specified by the ACMA (Australian  
Communications and Media Authority).  
Customer Care International  
USA & Canada - Tel: 800-732-2677  
Monday - Friday 8 AM - 8 PM / Saturday 9 AM – 5 PM  
Australia - Tel: 1800 786 608  
Monday - Friday 7:30 AM - 5 PM  
New Zealand - Tel: 0800 543 054  
Monday - Friday 10:30 AM - 7 PM  
This product has the benefit of a limited manufacturer’s warranty. Details of the warranty applicable to this  
®
envelope to PetSafe Ltd. Redthorn House, Unit 9, Chorley West Business Park, Ackhurst Road, Chorley,  
Lancashire PR7 1NL, United Kingdom.  
Perchlorate Battery  
21  
 
22  
1-800-732-2677  
 
®
Radio Systems Corporation  
10427 PetSafe Way  
Knoxville, TN 37932  
1-800-732-2677  
Protected by US Patents 6,879,300;  
6,921,089; 7,142,167 and D515,027.  
400-1422  
©2006 Radio Systems Corporation  
 

Peavey Musical Instrument Amplifier 7 9780300698 User Manual
Philips Blu ray Player BDP5005 User Manual
Philips Home Theater System SBC RU950 User Manual
Philips Laptop 13NB5604 User Manual
Philips Network Card SDJ6133W User Manual
Philips Universal Remote RU 600 User Manual
Philips VCR VRZ264AT User Manual
Poulan Tiller 418121 User Manual
Pride Mobility Wheelchair PMV 500 User Manual
Promise Technology Computer Hardware NS4300N User Manual