Pella Window 80KM0103 User Manual

Part Number: 80KM0103  
©2008 Pella Corporation  
INSTALLATION INSTRUCTIONS  
HINGED PATIO DOOR - SOUTHWESTERN WALL WITH HARD COAT STUCCO  
Installation Instructions for Typical Wood Frame Construction.  
These instructions were developed and tested for use with typical wood frame wall construction in a wall system designed to manage water.  
These instructions are not to be used with any other construction method. Installation instructions for use with other construction methods,  
multiple units or bow and bay windows, may be obtained from Pella® Corporation or a local Pella retailer. Building designs, construction methods,  
building materials, and site conditions unique to your project may require an installation method different from these instructions and additional  
care. Determining the appropriate installation method is the responsibility of you, your architect, or construction professional.  
YOU WILL NEED TO SUPPLY:  
TOOLS REQUIRED:  
s #EDAR OR )MPERVIOUS SHIMSꢀSPACERS ꢁꢂꢃ TO ꢃꢄ  
s 4APE MEASURE  
s ꢃꢅ GALVANIZED ROOlNG NAILS ꢁꢂꢀꢆ LBꢇ  
s ꢋg ,EVEL  
s #LOSED CELL FOAM BACKER RODꢀSEALANT BACKER ꢁꢂꢃ TO ꢈꢄ FTꢇ  
s 0ELLA® 3MART&LASH- FOIL BACKED BUTYL WINDOW AND DOOR  
s 3QUARE  
flashing tape or equivalent  
s (AMMER  
s 3TAPLER  
s (IGH QUALITY EXTERIOR GRADE POLYURETHANE OR SILICONE SEALANT  
ꢁꢃ TO ꢈ TUBES PER DOOR  
4&"-"/5  
s 'REAT 3TUFF Window and Door Insulating Foam Sealant  
by the Dow Chemical Company or equivalent low pressure  
polyurethane window and door foam - DO NOT use high  
PRESSURE OR LATEX FOAMSꢇ  
s 0ELLA ALUMINUM SILL SUPPORT OR ꢃ X ꢆ WOOD BLOCKING  
s )NTERIOR TRIM ANDꢀOR JAMB EXTENSIONS ꢁꢂꢉ TO ꢆꢄ FTꢇ  
s ꢊꢅ WIDE &ORTIlBER mASHING PAPER OR EQUIVALENT  
s 3EALANT GUN  
s 3CISSORS OR UTILITY KNIFE  
s $RILL  
s 3CREWDRIVERS  
ꢁꢌꢃ 0HILLIPS WITH ꢍꢅ SHAFT AND SMALL mAT BLADE  
REMEMBER TO USE APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT.  
'JO  
/BJMJOHꢂ'JO  
$PSOFS  
ꢀꢁ  
ꢀꢁꢂXJEFꢂ'MBTIJOHꢂ1BQFS  
'
M
B
T
ꢀꢁ  
J
'
M
5PQ  
O
H
B
T
'MBTIJOH  
5BQF  
4JEF  
I
J
1
B
Q
F
S
'MBTIJOH  
5BQF  
O
H
*OUFSMPDLFS  
1
B
ꢀꢁꢂ'MBTIJOHꢂ1BQFS  
Q
F
S
4JEF  
'MBTIJOH  
5BQF  
4JMMꢂ4VQQPSU  
4JMMꢂ'MBTIJOHꢂ5BQFꢂꢃꢅ  
4JMMꢂ'MBTIJOHꢂ5BQFꢂꢃꢄ  
Always read the Pella® ,IMITED 7ARRANTY BEFORE PURCHASING OR INSTALLING 0ELLA PRODUCTSꢇ "Y INSTALLING THIS PRODUCTꢎ YOU ARE ACKNOWLEDGING  
that this Limited Warranty is part of the terms of the sale. Failure to comply with all Pella installation and maintenance instructions may void your Pella product  
warranty. See Limited Warranty for complete details at http://warranty.pella.com.  
 
2
SETTING AND FASTENING THE DOOR  
A. Remove plastic wrap and cardboard packaging from door. DO NOT remove plastic  
SHIPPING SPACERSꢇ 4HE SHIPPING SPACERS WILL HELP KEEP THE DOOR SQUARE DURING INSTALLATIONꢇ  
$/ ./4 UNLOCK OR OPEN THE DOOR UNTIL IT IS FULLY FASTENEDꢇ  
Ó
Note: If screens, grilles or hardware are removed from the door at this time, label  
them and store them in a protected area.  
Óꢁ  
B. Fold out installation fin to 90°. "E CAREFUL NOT TO REMOVE OR TEAR THE lN CORNERSꢇ  
Note: If the fin is not at 90°, the door will not line up correctly on the interior.  
Óꢂ  
&YUFSJPS  
&YUFSJPS  
*OUFSJPS  
C. Place three 3/8" beads of sealant. 4HE lRST BEAD SHOULD BE APPROXIMATELY ꢈꢀꢆꢅ FROM  
THE EXTERIOR OF THE ROUGH OPENINGꢎ THE SECOND BEAD SHOULD BE PLACED SO IT IS UNDER THE  
WOOD INTERIOR THRESHOLD OF THE DOORꢇ 0LACEMENT WILL VARY DEPENDING ON WALL THICKNESS  
AND DOOR TYPEꢇ 0LACE A THIRD BEAD OF SEALANT IN THE GROOVE OF THE SILL SUPPORT OR ꢂꢀꢆꢅ  
FROM THE EXTERIOR EDGE OF THE WOOD BLOCKINGꢇ  
TWO OR MORE PEOPLE WILL BE REQUIRED FOR THE FOLLOWING STEPS.  
D. Insert the door FROM THE EXTERIOR OF THE BUILDINGꢇ $/ ./4 SLIDE THE BOTTOM OF  
the door into the opening. Sliding will damage the sealant lines. Place the bottom  
of the door at the bottom of the opening, then tilt the top into position. Center the  
door between the sides of the opening to allow clearance for shimming, and insert  
ONE ROOlNG NAIL IN THE lRST HOLE FROM THE CORNER ON EACH END OF THE TOP NAILING lNꢇ  
These are used to hold the door in place while shimming it plumb and square.  
Óꢃ  
E. Plumb and square door. 0LACE SHIMS AT EACH HINGE AND LOCK STRIKE LOCATION BETWEEN THE  
DOOR AND THE SIDES OF THE OPENINGꢇ )NSERT SHIMS IN OTHER LOCATIONS AS NEEDED STARTING UP ꢋꢅ  
FROM THE BOTTOM OF THE DOOR TO SQUARE IT IN THE OPENINGꢇ -AKE SURE THAT THE REVEAL AROUND  
THE DOORꢁS IS EQUALꢇ /N DOUBLE DOORSꢎ MAKE SURE THAT PANELS ARE EVEN ACROSS THE BOTTOMꢇ  
Note: On center latch double doors the lock strike will not be shimmed since it is  
located in the center of the unit. DO NOT over shim.  
Óꢃ  
Óꢃ  
Óꢃ  
F. Check the interior reveal. -AKE SURE THE MEASUREMENT FROM THE INTERIOR FACE OF THE DOOR  
to the interior face of the wall is equal at several points around the door.  
Óꢄ  
Note: If the dimensions are not equal, check to make sure the fins are folded out to 90°  
at all points.  
£
ꢇ ꢁꢆꢃ-  
ä
 
Ó
ä
Ó
Î
Î
{
ä
x
ä
È
ä
Ç
ä
 
'ꢇ Fasten the door to opening BY DRIVING ꢃꢅ GALVANIZED ROOlNG NAILS INTO EACH  
PREꢏPUNCHED HOLE IN THE NAILING lNꢇ  
&YUFSJPS  
Note: Make sure the fin corner is lying as flat as possible. When using  
the optional fin at the sill, attach the aluminum sill support or wood  
blocking under the sill of the door before proceeding to Step H.  
Óꢅ  
(Carefully open the door(s) and remove all shipping spacers.  
Note: Be sure to remove the spacers from the bottom edge of the door panel.  
Óꢇ  
Double doors with center latch:  
Designer Series Only: Use the construction handle to operate the active door  
HANDLEꢇ /PERATE THE mUSHBOLTS PER THE INSTRUCTIONS ON THE LABEL ON THE STRIKE  
located on the astragal.  
Architect Series Only: Use the construction handle to operate both the active  
and passive door panels.  
I. Out-swing doors: Place a dab of sealant in each of the pre-drilled holes in the bottom of the door frame, then insert a  
ꢌꢍ X ꢃꢅ mAT HEAD CORROSION RESISTANT WOOD SCREW ꢁPROVIDED INTO THIS HOLEꢇ  
Note: Single doors will have two pre-drilled holes, double doors will have four.  
)ꢂOut-swing double doors only: 0LACE A DAB OF SEALANT INTO THE CENTER HOLE OF THE STRIKE PLATE LOCATED AT THE SILL OF THE DOORꢇ  
)NSTALL A ꢌꢍ X ꢃꢅ mAT HEAD CORROSION RESISTANT WOOD SCREW ꢁPROVIDED INTO THIS HOLEꢇ  
Note: For masonry floors, use a #8 masonry screw instead of the wood screw.  
J. On center latching (double) doors: Place shims at the top of the door frame above  
THE CENTER STRIKE PLATEꢇ 3ECURE THE SHIMS BY INSERTING A ꢌꢍ X ꢈꢅ mAT HEAD CORROSION  
*OUFSJPS  
RESISTANT SCREW INTO THE UPPER DOOR FRAME THROUGH THE CENTER HOLE OF THE STRIKE PLATE  
and the shims into the rough opening.  
Óꢉ  
*ꢂOn center hinged double doors: Insert and attach shims directly  
above the astragal in the center of the unit.  
Note: Step K does not apply to center hinged doors.  
K. On each hinge, starting at the top, insert a 3" long screw ꢁPROVIDED INTO THE  
OPEN SCREW HOLEꢇ -AKE SURE THAT THE SCREW PASSES THROUGH THE SHIMS AND INTO THE  
structural framing.  
Óꢈ  
L. Check door operation. /PEN AND CLOSE THE DOOR TO CHECK FOR PROPER OPERATIONꢇ  
-AKE SURE THE DOOR WILL LATCH CORRECTLYꢇ  
Note: If there are any problems with the operation, recheck and adjust the reveal.  
M. Adjust the reveal if needed.  
Architect Series and Designer Series only: 4HE DOOR PANELS HAVE ADJUSTABLE HINGE LEAFSꢇ 5SING A ꢂꢀꢍꢅ ALLEN WRENCH  
TURN THE CENTER SCREW CLOCKWISE TO INCREASE THE SPACE BETWEEN THE HINGE SIDE OF THE FRAME AND THE DOOR PANELꢎ OR COUNTER  
CLOCKWISE TO INCREASE THE SPACE BETWEEN THE DOOR PANEL AND THE LOCK SIDE OF THE FRAMEꢇ $/ ./4 TURN THE SCREWS MORE  
THAN ꢈꢀꢆ TURN IN EITHER DIRECTIONꢇ )N SOME CASES IT MAY BE NECESSARY TO LOOSEN AND THEN TIGHTEN THE TOP AND BOTTOM HINGE  
screws to obtain full hinge adjustment. If necessary, loosen the top and bottom screws, and immediately retighten them.  
With the screws retightened, turn the adjustment hinge screw. If the hinge will not adjust any further then it is adjusted  
as far as it will go. If more clearance is needed adjust the shims between the frame and the rough opening.  
Note: DO NOT adjust the hinge with the top and bottom screws loose; this could force the hinge to adjust beyond  
its design capability which can cause the hinge to bind, damage the hinge and/or pull out the screws. A 3/4 turn of  
the center screw provides approximately 1/16" adjustment.  
Óꢊ  
Ó  
Note: For more issues with the adjustable strike latching, go to the troubleshooting section at the end of this instruction.  
ProLine Series only: Plastic shims located behind the hinges may be removed to adjust the reveal between the door panel  
and door frame. Additional hinge shims may be added if required.  
N. On doors with a lock strike in the side, DRILL A ꢂꢀꢍꢅ DIAMETER X ꢃꢅ DEEP PILOT HOLE THROUGH THE LOCK STRIKE AND INTO THE  
ROUGH OPENINGꢇ )NSERT A ꢌꢍ X ꢈꢅ CORROSION RESISTANT SCREW ꢁPROVIDED INTO THE PILOT HOLE MAKING SURE THAT IT PASSES THROUGH  
the shim and into the stud.  
Note: This step does not apply to center latching double doors.  
O. Install a #8 x 3" flat head corrosion resistant screw INTO THE HOLE LOCATED APPROXIMATELY ꢍꢅ FROM THE TOP OF THE  
door frame, on the latch side of the frame.  
 
3
INTEGRATING THE DOOR TO THE BUILDING FELT  
Note: The flashing tape must be applied approximately 1/2" onto the frame cladding at the jambs and  
head. Pre-folding the tape at 1/2" before removing the paper backing will make it easier to apply the  
tape correctly. If the siding is less than 1/2" thick, adjust the dimension of the fold so the exterior sealant  
line will cover the exterior edge of the tape.  
&YUFSJPS  
A. Apply side flashing tape. #UT ꢃ PIECES OF mASHING  
TAPE ꢆꢅ LONGER THAN THE FRAME HEIGHT OF THE DOORꢇ  
!PPLY ONE PIECE ꢂꢀꢃꢅ UP ONTO THE FRAME CLADDINGꢎ  
OVER THE NAILING lN AND ONTO THE mASHING PAPER TO  
EACH SIDEꢇ 4HE TAPE SHOULD EXTEND ꢃꢅ ABOVE THE TOP  
OF THE DOOR AND ꢃꢅ BELOW THE BOTTOM OF THE DOORꢇ  
0RESS THE TAPE DOWN lRMLY WHILE FOLDING DOWN THE  
EXCESS TAPE AT THE TOP AND BOTTOM OF THE DOORꢇ  
Îꢀ  
&YUFSJPS  
B. Apply top flashing tape. Cut a piece of flashing tape long enough to go across  
THE TOP OF THE DOOR AND EXTEND AT LEAST ꢂꢅ PAST THE SIDE mASHING TAPE ON BOTH SIDESꢇ  
!PPLY THE TAPE ꢂꢀꢃꢅ UP ONTO THE FRAME CLADDINGꢎ OVER THE TOP NAILING lN AS SHOWNꢇ  
&OLD THE OVERLAPPING TAPE DOWNꢎ AND PRESS ALL TAPE DOWN lRMLYꢇ  
Î
ꢅꢁ  
Note: The top flashing tape must overlap the side flashing tape to prevent  
water from getting behind it.  
C. Apply the top flashing paper. #UT ONE PIECE OF mASHING PAPER AT LEAST ꢃꢂꢅ LONGER THAN THE  
width of the rough opening. Position the bottom edge of the flashing paper flush with the  
frame of the door and center the flashing paper with the door. Staple the flashing paper to  
the header.  
Îꢁ  
Note: When applying the first layer of building felt, ensure the sill flashing paper  
overlaps the building felt. This will tie the door system into the building water  
management system.  
4
INTERIOR SEAL  
Caution: Ensure use of low pressure polyurethane window and door installation foams and strictly follow the foam manufacturer’s  
recommendations for application. Use of high pressure foams or improper application of the foam may cause the door to bow and  
hinder operation. DO NOT use fiberglass insulation.  
A. Apply insulating foam. &ROM THE INTERIORꢎ INSERT THE NOZZLE OF THE APPLICATOR APPROXIMATELY  
ꢂꢅ DEEP INTO THE SPACE BETWEEN THE DOOR AND THE ROUGH OPENING AND APPLY A ꢂꢅ DEEP BEAD  
OF FOAMꢇ 4HIS WILL ALLOW ROOM FOR EXPANSION OF THE FOAM AND WILL MINIMIZE SQUEEZE OUTꢇ )F  
*OUFSJPS  
USING FOAM OTHER THAN 'REAT 3TUFF - 7INDOW AND $OOR )NSULATING &OAM 3EALANT BY THE  
$OW #HEMICAL #OMPANYꢎ ALLOW THE FOAM TO CURE COMPLETELY ꢁUSUALLY ꢍ TO ꢃꢆ HOURS BEFORE  
PROCEEDING TO THE NEXT STEPꢇ  
Note: DO NOT completely fill the space from the back of the fin to the interior face of  
the opening.  
{ꢀ  
B. Check the door operation by opening and closing the door.  
Note: If the door does not operate correctly, check to make sure it is still plumb, level, square and  
that the sides are not bowed. If adjustments are required, remove the foam with a serrated knife.  
Adjust the shims, and reapply the insulating foam sealant.  
 
5
SEALING THE DOOR TO THE EXTERIOR WALL CLADDING  
Note: When applying the casing bead for stucco, leave 1/2" space between the  
head of the door and the casing bead, and 3/8" space between the door jambs  
and the casing bead for backer rod and sealant. Refer to the illustration  
(Southwestern Wall With Stucco).  
4065)8&45&3/  
8"--  
8*5)ꢂ  
456$$0  
Note: The sealant details shown are standard recommendations from the  
sealant industry. Contact your sealant supplier for recommendations and  
instructions for this and any other application.  
#BDLFSꢂ3PEꢂBOE  
4FBMBOUꢂUZQJDBM  
ꢅꢆꢄꢁꢂ$MFBSBODF  
"DDFTTPSZꢂ  
(SPPWF  
*OTVMBUJOH  
'PBN  
A. Install the hardware. 2EFER TO THE INSTRUCTIONS INCLUDED IN THE HARDWARE BOXꢇ  
ꢅꢆꢄꢁ  
B. Insert backer rod INTO THE SPACE AROUND THE DOOR LEAVING AT LEAST A ꢂꢀꢃꢅ  
CLEARANCE BETWEEN THE BACKER ROD AND THE EXTERIOR FACE OF THE CASING BEADꢇ  
Note: Backer rod adds shape and depth for the sealant line.  
C. Apply a bead of high quality exterior grade sealant  
to the entire perimeter of the door. At each end of the  
bottom of the door, insert sealant into the spaces between  
the bottom of the door and the sill support and connect  
it to the perimeter sealant.  
xꢁ  
D. Shape, tool and clean excess sealant. 7HEN lNISHEDꢎ  
x
the sealant should be the shape of an hourglass.  
Note: This method creates a more flexible sealant  
line capable of expanding and contracting.  
E. Remove plastic guards at the base of the door  
once construction is complete.  
6
INTERIOR FINISHING  
)F THE PRODUCTS CANNOT BE lNISHED IMMEDIATELYꢎ COVER WITH CLEAR PLASTIC TO PROTECT FROM DIRTꢎ DAMAGE AND MOISTUREꢇ 2EMOVE ANY CONSTRUCTION  
RESIDUE BEFORE lNISHINGꢇ 3AND ALL WOOD SURFACES LIGHTLY WITH ꢂꢍꢄ GRIT OR lNER SANDPAPERꢇ $/ ./4 USE STEEL WOOLꢇ "% #!2%&5, ./4 4/  
3#2!4#( 4(% ',!33ꢇ 2EMOVE SANDING DUSTꢇ  
0ELLA PRODUCTS MUST BE lNISHED PER THE BELOW INSTRUCTIONSꢐ FAILURE TO FOLLOW THESE INSTRUCTIONS VOIDS THE ,IMITED 7ARRANTYꢇ  
s /N CASEMENT AND AWNINGSꢎ IT IS OPTIONAL TO PAINTꢎ STAIN OR lNISH THE VERTICAL AND HORIZONTAL SASH EDGESꢇ  
s /N SINGLEꢏHUNG AND DOUBLEꢏHUNGꢎ DO NOT PAINTꢎ STAIN OR lNISH THE VERTICAL SASH EDGESꢎ ANY lNISH ON THE VERTICAL SASH EDGES MAY CAUSE THE SASH  
TO STICKꢐ IT IS OPTIONAL TO PAINTꢎ STAIN OR lNISH THE HORIZONTAL SASH EDGESꢇ  
s /N PATIO DOORSꢎ IT IS OPTIONAL TO PAINTꢎ STAIN OR lNISH THE VERTICAL AND HORIZONTAL PANEL EDGESꢇ  
Note: To maintain proper product performance do not paint, finish or remove the weather-stripping, mohair dust pads, gaskets or vinyl  
parts. Air and water leakage will result if these parts are removed. After finishing, allow venting windows and doors to dry completely  
before closing them.  
0ELLA #ORPORATION IS NOT RESPONSIBLE FOR INTERIOR PAINT AND STAIN lNISH IMPERFECTIONS FOR ANY PRODUCT THAT IS NOT FACTORYꢏAPPLIED BY 0ELLA  
#ORPORATIONꢇ 5SE OF INAPPROPRIATE lNISHESꢎ SOLVENTSꢎ BRICKWASHꢎ OR CLEANING CHEMICALS WILL CAUSE ADVERSE REACTIONS WITH WINDOW AND DOOR  
materials and voids the Limited Warranty.  
&OR ADDITIONAL INFORMATION ON lNISHING SEE THE 0ELLA /WNERꢑS -ANUAL OR GO TO www.pella.com.  
 
EXTERIOR FINISH  
4HE EXTERIOR FRAME AND SASH ARE PROTECTED BY ALUMINUM CLADDING WITH OUR TOUGH %NDURA#LAD® OR %NDURA#LAD 0LUS BAKEDꢏON FACTORY  
lNISH THAT NEEDS NO PAINTINGꢇ #LEAN THIS SURFACE WITH MILD SOAP AND WATERꢇ 3TUBBORN STAINS AND DEPOSITS MAY BE REMOVED WITH MINERAL  
spirits. DO NOT use abrasives. DO NOT scrape or use tools that might damage the surface.  
5SE OF INAPPROPRIATE lNISHESꢎ SOLVENTSꢎ BRICKWASH OR CLEANING CHEMICALS WILL CAUSE ADVERSE REACTIONS WITH WINDOW AND DOOR MATERIALS AND  
voids the Limited Warranty.  
CARE AND MAINTENANCE  
#ARE AND MAINTENANCE INFORMATION IS AVAILABLE IN THE 0ELLA /WNERꢑS -ANUALꢇ 9OU CAN OBTAIN AN OWNERꢑS MANUAL BY CONTACTING YOUR LOCAL  
Pella retailer. This information is also available at www.pella.com.  
IMPORTANT NOTICE  
"ECAUSE ALL CONSTRUCTION MUST ANTICIPATE SOME WATER INlLTRATIONꢎ IT IS IMPORTANT THAT THE WALL SYSTEM BE DESIGNED AND CONSTRUCTED TO  
properly manage moisture. Pella Corporation is not responsible for claims or damages caused by anticipated and unanticipated water  
INlLTRATIONꢐ DElCIENCIES IN BUILDING DESIGNꢎ CONSTRUCTION AND MAINTENANCEꢐ FAILURE TO INSTALL 0ELLA PRODUCTS IN ACCORDANCE WITH 0ELLAꢑS  
INSTALLATION INSTRUCTIONSꢐ OR THE USE OF 0ELLA PRODUCTS IN WALL SYSTEMS WHICH DO NOT ALLOW FOR PROPER MANAGEMENT OF MOISTURE WITHIN THE  
wall systems. The determination of the suitability of all building components, including the use of Pella products, as well as the design  
and installation of flashing and sealing systems are the responsibility of the Buyer or User, the architect, contractor, installer, or other  
construction professional and are not the responsibility of Pella.  
Pella products should not be used in barrier wall systems which do not allow for proper management of moisture within the wall systems,  
SUCH AS BARRIER %XTERIOR )NSULATION AND &INISH 3YSTEMSꢎ ꢁ%)&3 ꢁALSO KNOWN AS SYNTHETIC STUCCO OR OTHER NONꢏWATER MANAGED SYSTEMSꢇ  
%XCEPT IN THE STATES OF #ALIFORNIAꢎ .EW -EXICOꢎ !RIZONAꢎ .EVADAꢎ 5TAHꢎ AND #OLORADOꢎ Pella makes no warranty of any kind on and  
assumes no responsibility for Pella windows and doors installed in barrier wall systems. In the states listed above, the installation  
of Pella products in barrier wall or similar systems must be in accordance with Pella’s installation instructions.  
0RODUCT MODIlCATIONS THAT ARE NOT APPROVED BY 0ELLA #ORPORATION WILL VOID THE ,IMITED 7ARRANTYꢇ  
TROUBLESHOOTING - Adjustable Strike Latching Issues  
Note: Troubleshooting is for Architect Series® and Designer Series® only.  
Issue 1:  
Door is difficult  
to latch. Remove  
THE STRIKE AND  
"EKꢉꢂ4USJLFꢂ4IJN  
ADJUSTABLE STRIKE  
FOEꢂWJFXꢈ  
shim then reinstall  
THE STRIKEꢇ  
'BDUPSZꢂ  
JOTUBMMFEꢂ  
TJEF  
4JEFꢂUPꢂCFꢂ  
VTFEꢂJOꢂ  
*TTVFꢂꢄ  
Issue 2:  
Door needs to close more  
tightly against the weather-  
strip. Remove  
5"#4  
THE STRIKE AND  
ADJUSTABLE STRIKE  
shim. Remove  
the tabs from the  
ADJUSTABLE STRIKE  
shim and install  
SO THAT THE THICKER  
side is visible at  
THE STRIKE EDGEꢇ  
2EINSTALL THE STRIKEꢇ  
"EKVTUBCMFꢂTUSJLFꢂTIJN  
TJEFꢂWJFXꢈ  
4USJLF  
GSPOUꢂWJFXꢈ  
 

Patton electronic Switch 457B User Manual
Peerless Industries Projector Accessories PRS 35 User Manual
Philips Battery Charger SCB1205 12 User Manual
Philips Car Stereo System CID3692 User Manual
Philips Headphones SBCHC8900 User Manual
Philips Projection Television 9P5044C1 User Manual
Philips Stereo System MME 100 User Manual
Philips TV Cables SWA2531 User Manual
Pinnacle Design TV Video Accessories TV30103 User Manual
PYLE Audio Music Mixer PMX 1205 User Manual