Pelco Switch C808M G User Manual

I N S T A L L A T I O N / O P E R A T I O N

VS5004/VS5008

Sequential Switcher

C808M-G (4/05)

Description

The VS5004 and VS5008 sequential switchers are designed to switch up to four (VS5004) or eight (VS5008) cameras manually or automatically to

one or two monitors with automatic response to alarm inputs. Both versions are Coaxitron^®compatible and can be placed on a desktop or rack

mounted.

MODELS

VS5004

VS5004/220

VS5008

Sequential switcher with four camera inputs and two monitor outputs, 120 VAC

Same as VS5004 except 230 VAC

Sequential switcher with eight camera inputs and two monitor outputs, 120 VAC

Same as VS5008 except 230 VAC

VS5008/220

C808M-G (4/05)

Installation

TERMINATED CAMERA INPUTS AND ONE MONITOR OUTPUT

1. Make all equipment connections. Refer to Figure 1 (VS5004) or Figure 2 (VS5008).

VS5008 only: When conﬁgured for one-monitor operation, the monitor must be connected to the MON 2 output. The MON 1 output must

be terminated with a 75-ohm BNC terminator.

2. Make alarm connections if required. Refer to Figure 3 (VS5004) or Figure 4 (VS5008) and do the following:

VS5004

a. Input: Connect the alarm contact between the appropriate input (pins 1-4) and common (pin 5) on the 6-pin connector receptacle.

Pins 1 thru 4 directly correspond with the like-numbered front panel camera switches of the VS5004. The alarm output is an

open-collector NPN transistor. Current from the output to circuit ground should not exceed 600 mA.

b. Output: To activate an external device during an alarm, connect the device at pins 5 and 6 on the 6-pin connector.

VS5008

a. Input: Connect the alarm contact between the appropriate ALARM INPUT (terminals 1-8) and common (COM) terminal. The alarm

output is an open-collector NPN transistor. Current from the output to circuit ground should not exceed 40 mA.

b. Output: To activate an external device during an alarm, connect the device at the ALARM OUT terminal and the common (COM)

terminal.

3. Set the ALARM switch to the ON position.

NOTES:

•

When an alarm occurs, the monitor immediately switches to the alarmed channel, and the associated LED blinks. Multiple alarmed

channels sequence every ﬁve seconds (VS5004) or three seconds (VS5008). The alarm has priority over the MONITOR/AUTO/BYPASS

switch settings.

•

Once triggered, the alarm remains on until the input condition is removed or the ALARM switch is moved to the OFF position.

When the ALARM switch is set to the OFF position, all alarm inputs are ignored.

4. For channels with cameras connected to the video inputs, set the front panel switches to the AUTO position. All unconnected video inputs

should have their channel switches set to the BYPASS position.

NOTE: All channels with a switch in the AUTO position will automatically sequence through the monitor. To view one speciﬁc channel

continuously, set the corresponding switch to the MONITOR position. To remove a channel from the sequence, set the corresponding switch to

the BYPASS position.

5. Connect the AC adapter to the 12 VAC input plug on the rear of the VS5004 or VS5008. Connect the transformer to a 120 VAC (VS5004 or

VS5008) or 230 VAC (VS5004/220 or VS5008/220) power source. After power up, the switcher will begin sequencing.

6. Using a screwdriver, adjust the DWELL interval control to the desired setting. This control adjusts the interval time from a minimum of

1 second to a maximum of 70 seconds nominal. To increase the interval, turn the control clockwise. To decrease the interval, turn the

control counterclockwise. The DWELL interval control is a precision 15-turn potentiometer. Each complete turn of this control will adjust the

time interval by approximately 4 to 5 seconds.

MON 1

BRIGHT

CONTRAST

12 VAC

INPUT

ALARM

MON 1

MON 2

IN 1 2 3 4

OUT 6

COMMON 5

Figure 1. VS5004 Terminated Camera Inputs - One Monitor

C808M-G (4/05)

NOTE: MON 1 MUST BE

TERMINATED.

CAMERAS

MON 1

ALARM

INPUT

COM

12 VAC

MON 2 MON X

INPUT

ALARM OUT

VS5008 (REAR)

Figure 2. VS5008 Terminated Camera Inputs - One Monitor

6-PIN CONNECTOR

RECEPTACLE

YEL

BRN

REAR VIEW

GRN

BLK

CAMERAS

12VAC

INPUT

ALARM

MON 1

MON 2

IN 1 2 3 4

OUT 6 -- TO VCR

COMMON

TO EXTERNAL

ALARM CIRCUITRY

Figure 3. VS5004 Alarm Connections

C808M-G (4/05)

UP TO EIGHT ALARM INPUTS (ALARM INPUT FROM

MOTION DETECTOR, DOOR CONTACT, ETC., THROUGH

NORMALLY OPEN SWITCH). EACH ALARM DEVICE MUST BE

CONNECTED TO THE "COM" TERMINAL.

UP TO EIGHT VIDEO INPUTS

CAMERAS

MON 1

ALARM

COM

12 VAC

INPUT

MON 2 MON X

ALARM OUT

VS5008 (REAR)

VCR

OPEN COLLECTOR OUTPUT FOR

VCR ACTIVATION IN ALARM

CONDITION. ONLY ONE VCR

CAN BE USED IN THIS

CONFIGURATION.

Figure 4. VS5008 Alarm Connections

C808M-G (4/05)

LOOPING CAMERA INPUTS AND ONE MONITOR OUTPUT

1. Convert the switcher to looping operation. Refer to Figure 5 and do the following:

NOTE: Looping and terminated inputs may be mixed.

a. Remove the cover.

b. Remove the rear panel of the chassis.

c. Locate the 75-ohm resistors located on the inside of the rear panel BNC jacks.

d. For each input to be looped, use wire cutters to clip one of the attached resistor leads.

e. Replace the cover.

2. Make all equipment connections. Refer to Figure 6 (VS5004) or Figure 7 (VS5008).

VS5008 only: When conﬁgured for one-monitor operation, the monitor must be connected to the MON 2 output. The MON 1 output must

be terminated with a 75-ohm BNC terminator.

3. Make alarm connections if required. Refer to Figure 3 (VS5004) or Figure 4 (VS5008) and do the following:

VS5004

a. Input: Connect the alarm contact between the appropriate input (pins 1-4) and common (pin 5) on the 6-pin connector receptacle.

Pins 1 thru 4 correspond directly with the like-numbered front panel camera switches of the VS5004. The alarm output is an

open-collector NPN transistor. Current from the output to circuit ground should not exceed 600 mA.

b. Output: To activate an external device during an alarm, connect the device at pins 5 and 6 on the 6-pin connector.

VS5008

a. Input: Connect the alarm contact between the appropriate ALARM INPUT (terminals 1-8) and common (COM) terminal. The alarm

output is an open-collector NPN transistor. Current from the output to circuit ground should not exceed 40 mA.

b. Output: To activate an external device during an alarm, connect the device at the ALARM OUT terminal and the common (COM)

terminal.

4. Set the ALARM switch to the ON position.

NOTES:

•

When an alarm occurs, the monitor immediately switches to the alarmed channel, and the associated LED blinks. Multiple alarmed

channels sequence every ﬁve seconds (VS5004) or three seconds (VS5008). The alarm has priority over the MONITOR/AUTO/BYPASS

switch settings.

•

Once triggered, the alarm remains on until the input condition is removed or the ALARM switch is moved to the OFF position.

When in the ALARM switch is set to the OFF position, all alarm inputs are ignored.

5. For channels with cameras connected to the video inputs, set the front panel switches to the AUTO position. All unconnected video inputs

should have their channel switch set to the BYPASS position.

NOTE: All channels with a switch in the AUTO position will automatically sequence through the monitor. To view one speciﬁc channel

continuously, set the corresponding switch to the MONITOR position. To remove a channel from the sequence, set the corresponding switch to

the BYPASS position.

6. Connect the AC adapter to the 12 VAC input plug on the rear of the VS5004 or VS5008. Connect the transformer to a 120 VAC (VS5004 or

VS5008) or 230 VAC (VS5004/220 or VS5008/220) power source. After power up, the switcher will begin sequencing.

7. Using a screwdriver, adjust the DWELL interval control to the desired setting. This control adjusts the interval time from a minimum of

1 second to a maximum of 70 seconds nominal. To increase the interval, turn the control clockwise. To decrease the interval, turn the

control counterclockwise. The DWELL interval control is a precision 15-turn potentiometer. Each complete turn of this control will adjust the

time interval by approximately 4 to 5 seconds.

C808M-G (4/05)

75-OHM RESISTOR

CLIP HERE

FOR EACH

CHANNEL

REAR PANEL (SWITCHER)

BNC CONNECTOR

Figure 5. Looping Conversion Modiﬁcation

MON 1

BRIGHT

CONTRAST

12 VAC

INPUT

ALARM

MON 1

MON 2

IN 1 2 3 4

OUT 6

COMMON 5

VIDEO INPUTS

ADDITIONAL EQUIPMENT

TERMINATED

Figure 6. VS5004 Looping Camera Inputs - One Monitor

C808M-G (4/05)

NOTE: IN THIS CONFIGURATION,

MON 1 MUST BE TERMINATED

AND THE UNIT MUST BE MODIFIED

TO BE LOOPING (REFER TO FIGURE 5).

CAMERAS

MON 1

ALARM

COM

12 VAC

INPUT

MON 2 MON X

ALARM OUT

VS5008 (REAR)

VIDEO INPUTS

ADDITIONAL EQUIPMENT

TERMINATED

Figure 7. VS5008 Looping Camera Inputs - One Monitor

TERMINATED CAMERA INPUTS AND TWO MONITOR OUTPUTS

1. Convert the VS5004 to dual-monitor operation. Refer to Figure 8 and do the following:

a. Remove the cover.

b. Remove the rear panel of the chassis.

c. Remove the four screws attaching the PC board to the chassis.

d. Pull the PC board and rear panel assembly out of the chassis.

e. Turn the PC board over and rewire.

Replace the PC board, rear panel assembly, and cover.

2. Make all equipment connections. Refer to Figure 9 (VS5004) or Figure 10 (VS5008).

VS5004 only: In this conﬁguration, MON 1 must be terminated with a 75-ohm terminator and MON 2 must be terminated in the HI Z position.

3. Make alarm connections if required. Refer to Figure 3 (VS5004) or Figure 4 (VS5008) and do the following:

VS5004

a. Input: Connect the alarm contact between the appropriate input (pins 1-4) and common (pin 5) on the 6-pin connector receptacle.

Pins 1 thru 4 correspond directly with the like-numbered front panel camera switches of the VS5004. The alarm output is an

open-collector NPN transistor. Current from the output to circuit ground should not exceed 600 mA.

b. Output: To activate an external device during an alarm, connect the device at pins 5 and 6 on the 6-pin connector.

VS5008

a. Input: Connect the alarm contact between the appropriate ALARM INPUT (terminals 1-8) and common (COM) terminal. The alarm

output is an open-collector NPN transistor. Current from the output to circuit ground should not exceed 40 mA.

b. Output: To activate an external device during an alarm, connect the device at the ALARM OUT terminal and the common (COM)

terminal.

C808M-G (4/05)

4. Set the ALARM switch to the ON position.

NOTES:

•

With all channel switches set to the AUTO position, both monitors immediately switch to the alarmed channel and the associated LED

blinks. Multiple alarmed channels sequence every ﬁve seconds (VS5004) or three seconds (VS5008). The alarm has priority over the

MONITOR/AUTO/BYPASS switch settings.

•

If a channel switch is set to the MONITOR position, Monitor 1 switches to the alarmed channel while Monitor 2 displays the selected

(MONITOR) channel.

•

If a channel switch is set to the BYPASS position, Monitor 1 switches to that channel if it is alarmed.

Once triggered, the alarm remains on until the input condition is removed or the ALARM switch is moved to the OFF position.

When in the ALARM switch is set to the OFF position, all alarm inputs are ignored.

5. For channels with cameras connected to the video inputs, set the front panel switches to the AUTO position. All unconnected video inputs

should have their channel switch set to the BYPASS position.

NOTES:

•

With all channel switches in the AUTO position, both monitors sequence simultaneously.

Monitor 2 can be manually switched to any channel for continuous viewing by setting the desired channel’s switch to the MONITOR

position. If multiple channels are set to MONITOR, only the lowest numbered channel will be displayed. This does not affect the

sequencing for Monitor 1.

•

To remove a channel from the sequence, set the corresponding switch to the BYPASS position.

6. Connect the AC adapter to the 12 VAC input plug on the rear of the VS5004 or VS5008. Connect the transformer to a 120 VAC (VS5004 or

VS5008) or 230 VAC (VS5004/220 or VS5008/220) power source. After power up, the switcher will begin sequencing.

7. Using a screwdriver, adjust the DWELL interval control to the desired setting. This control adjusts the interval time from a minimum of

1 second to a maximum of 70 seconds nominal. To increase the interval, turn the control clockwise. To decrease the interval, turn the

control counterclockwise. The DWELL interval control is a precision 15-turn potentiometer. Each complete turn of this control will adjust the

time interval by approximately 4 to 5 seconds.

MON 1 MON 2

PCB 90000101 COMPONENT SIDE

BLU

ORG

B2 V2

RED

BRN

B1 V1

MON1

GRN

W/RED

TO CONVERT PC BOARD TO TWO MONITOR OPERATION,

REROUTE THE JUMPER WIRES AS FOLLOWS.

WIRE COLOR

REMOVE WIRE

CONNECT WIRE

FROM PIN

TO PIN

BROWN

RED

ORANGE

YELLOW

GREEN

BLUE

WHITE/RED

Figure 8. VS5004 Conversion For Two-Monitor Operation

C808M-G (4/05)

MON 2

MON 1

BRIGHT

CONTRAST

BRIGHT

CONTRAST

12 VAC

INPUT

ALARM

MON 1

MON 2

IN 1 2 3 4

OUT 6

COMMON 5

NOTE: IN THIS CONFIGURATION, MON 1 MUST BE TERMINATED WITH A 75-OHM TERMINATOR

AND MON 2 MUST BE IN THE “HI Z” POSITION.

Figure 9. VS5004 Terminated Camera Inputs - Two Monitors

CAMERAS

MON 1

ALARM

INPUT

COM

12 VAC

INPUT

MON 2 MON X

ALARM OUT

VS5008 (REAR)

Figure 10. VS5008 Terminated Camera Inputs - Two Monitors

C808M-G (4/05)

LOOPING CAMERA INPUTS AND TWO MONITOR OUTPUTS

1. Convert the VS5004 to dual-monitor operation. Refer to Figure 8 and do the following:

a. Remove the cover.

b. Remove the rear panel of the chassis.

c. Remove the four screws attaching the PC board to the chassis.

d. Pull the PC board and rear panel assembly out of the chassis.

e. Turn the PC board over and rewire.

2. Convert to looping operation. Refer to Figure 5 and do the following:

NOTE: Looping and terminated inputs may be mixed.

a. Locate the 75-ohm resistors located on the inside of the rear panel BNC jacks.

b. For each input to be looped, use wire cutters to clip one of the attached resistor leads.

c. Replace the cover.

3. Make all equipment connections. Refer to Figure 11 (VS5004) or Figure 12 (VS5008).

(VS5004 only) In this conﬁguration, MON 1 must be terminated with a 75-ohm terminator and MON 2 must be terminated in the

HI Z position.

4. Make alarm connections if required. Refer to Figure 3 (VS5004) or Figure 4 (VS5008) and do the following:

VS5004

a. Input: Connect the alarm contact between the appropriate input (pins 1-4) and common (pin 5) on the 6-pin connector receptacle.

Pins 1 thru 4 correspond directly with the like-numbered front panel camera switches of the VS5004. The alarm output is an

open-collector NPN transistor. Current from the output to circuit ground should not exceed 600 mA.

b. Output: To activate an external device during an alarm, connect the device at pins 5 and 6 on the 6-pin connector.

VS5008

a. Input: Connect the alarm contact between the appropriate ALARM INPUT (terminals 1-8) and common (COM) terminal. The alarm

output is an open-collector NPN transistor. Current from the output to circuit ground should not exceed 40 mA.

b. Output: To activate an external device during an alarm, connect at the ALARM OUT terminal and the common (COM) terminal.

5. Set the ALARM switch to the ON position.

NOTES:

•

With all channel switches set to the AUTO position, both monitors immediately switch to the alarmed channel and the associated LED

blinks. Multiple alarmed channels sequence every ﬁve seconds (VS5004) or three seconds (VS5008). The alarm has priority over the

MONITOR/AUTO/BYPASS switch settings.

•

If a channel switch is set to the MONITOR position, Monitor 1 switches to the alarmed channel while Monitor 2 displays the selected

(MONITOR) channel.

•

If a channel switch is set to the BYPASS position, Monitor 1 switches to that channel if alarmed.

Once triggered, the alarm remains on until the input condition is removed or the ALARM switch is moved to the OFF position.

When in the ALARM switch is set to the OFF position, all alarm inputs are ignored.

6. For channels with cameras connected to the video inputs, set the front panel switches to the AUTO (center) position. All unconnected video

inputs should have their channel switch set to the BYPASS (down) position.

NOTES:

•

With all channel switches in the AUTO position, both monitors sequence simultaneously.

Monitor 2 can be manually switched to any channel for continuous viewing by setting the desired channel’s switch to the MONITOR

position. If multiple channels are set to MONITOR, only the lowest numbered channel will be displayed. This does not affect the

sequencing for Monitor 1.

•

To remove a channel from the sequence, set the corresponding switch to the BYPASS position.

C808M-G (4/05)

7. Connect the AC adapter to the 12 VAC input plug on the rear of the VS5004 or VS5008. Connect the transformer to a 120 VAC (VS5004 or

VS5008) or 230 VAC (VS5004/220 or VS5008/220) power source. After power up, the switcher will begin sequencing.

8. Using a screwdriver, adjust the DWELL interval control to the desired setting. This control adjusts the interval time from a minimum of

1 second to a maximum of 70 seconds nominal. To increase the interval, turn the control clockwise. To decrease the interval, turn the

control counterclockwise. The DWELL interval control is a precision 15-turn potentiometer. Each complete turn of this control will adjust the

time interval by approximately 4 to 5 seconds.

MON 2

MON 1

BRIGHT

CONTRAST

BRIGHT

CONTRAST

12 VAC

INPUT

ALARM

MON 1

MON 2

IN 1 2 3 4

OUT 6

COMMON 5

VIDEO INPUTS

ADDITIONAL EQUIPMENT

TERMINATED

NOTE: MON 1 MUST BE TERMINATED WITH A 75-OHM TERMINATOR AND MON 2 MUST BE IN

THE “HI Z” POSITION.

Figure 11. VS5004 Looping Camera Inputs - Two Monitors

NOTE: In this configuration

the unit must be modified in

order to be looping (refer to figure 5).

CAMERAS

MON 1

ALARM

COM

12 VAC

INPUT

MON 2 MON X

ALARM OUT

VS5008 (REAR)

VIDEO INPUTS

ADDITIONAL EQUIPMENT

TERMINATED

Figure 12. VS5008 Looping Camera Inputs- Two Monitors

C808M-G (4/05)

COAXITRON CONTROL

To convert for use with a Coaxitron transmitter, do the following:

1. Convert the VS5004 to dual-monitor operation. Refer to Figure 8 and do the following:

a. Remove the cover.

b. Remove the rear panel of the chassis.

c. Remove the four screws attaching the PC board to the chassis.

d. Pull the PC board and rear panel assembly out of the chassis.

e. Turn the PC board over and rewire.

2. Convert to looping operation. Refer to Figure 5 and do the following:

NOTE: Looping and terminated inputs may be mixed.

a. Locate the 75-ohm resistors located on the inside of the rear panel BNC jacks.

b. For each input to be looped, use wire cutters to clip one of the attached resistor leads.

c. Replace the cover.

3. Make all equipment connections. Refer to Figure 13 (VS5004) or Figure 14 (VS5008).

VS5004

•

The Coaxitron transmitter must be passive (nonampliﬁed).

To operate a camera via Coaxitron signals, the corresponding channel switch must be in the MONITOR position.

VS5008

•

The Coaxitron transmitter must be active (ampliﬁed).

4. Make alarm connections if required. Refer to Figure 3 (VS5004) or Figure 4 (VS5008) and do the following:

VS5004

a. Input: Connect the alarm contact between the appropriate input (pins 1-4) and common (pin 5) on the 6-pin connector receptacle.

Pins 1 thru 4 correspond directly with the like-numbered front panel camera switches of the VS5004. The alarm output is an

open-collector NPN transistor. Current from the output to circuit ground should not exceed 600 mA.

b. Output: To activate an external device during an alarm, connect the device at pins 5 and 6 on the 6-pin connector.

VS5008

a. Input: Connect the alarm contact between the appropriate ALARM INPUT (terminals 1-8) and common (COM) terminal. The alarm

output is an open-collector NPN transistor. Current from the output to circuit ground should not exceed 40 mA.

b. Output: To activate an external device during an alarm, connect the device at the ALARM OUT terminal and the common (COM)

terminal.

5. Set the ALARM switch to the ON position.

NOTES:

•

When an alarm occurs, the monitor immediately switches to the alarmed channel, and the associated LED blinks. Multiple alarmed

channels sequence every ﬁve seconds (VS5004) or three seconds (VS5008). The alarm has priority over the MONITOR/AUTO/BYPASS

switch settings.

VS5008 with two-monitor conﬁguration:

–

If a channel switch is set to the MONITOR position, Monitor 1 switches to the alarmed channel while Monitor 2 displays the selected

(MONITOR) channel.

–

If a channel switch is set to the BYPASS position, Monitor 1 switches to that channel if alarmed.

•

Once triggered, the alarm remains on until the input condition is removed or the ALARM switch is moved to the OFF position.

When in the ALARM switch is set to the OFF position, all alarm inputs are ignored.

C808M-G (4/05)

6. For channels with cameras connected to the video inputs, set the front panel switches to the AUTO position. All unconnected video inputs

should have their channel switch set to the BYPASS position.

NOTES:

•

VS5004 and VS5008 with one-monitor conﬁguration: All channels with a switch set in the AUTO position will automatically sequence

through the monitor. To view one speciﬁc channel continuously, set the corresponding switch to the MONITOR position. To remove a

channel from the sequence, set the corresponding switch to the BYPASS position.

•

VS5008 with two-monitor conﬁguration:

–

With all channel switches in the AUTO position, both monitors sequence simultaneously.

Monitor 2 can be manually switched to any channel for continuous viewing by setting the desired channel’s switch to the MONITOR

position. If multiple channels are set to MONITOR, only the lowest numbered channel will be displayed. This does not affect the

sequencing for Monitor 1.

–

To remove a channel from the sequence, set the corresponding switch to the BYPASS position.

7. Connect the AC adapter to the 12 VAC input plug on the rear of the VS5004 or VS5008. Connect the transformer to a 120 VAC (VS5004 or

VS5008) or 230 VAC (VS5004/220 or VS5008/220) power source. After power up, the switcher will begin sequencing.

8. Using a screwdriver, adjust the DWELL interval control to the desired setting. This control adjusts the interval time from a minimum of

1 second to a maximum of 70 seconds nominal. To increase the interval, turn the control clockwise. To decrease the interval, turn the

control counterclockwise. The DWELL interval control is a precision 15-turn potentiometer. Each complete turn of this control will adjust the

time interval by approximately 4 to 5 seconds.

C808M-G (4/05)

MON 1

COAXITRON®

RECEIVER

TO FIXED CAMERAS OR

ADDITIONAL RECEIVERS

BRIGHT

CONTRAST

12 VAC

INPUT

ALARM

MON 1

MON 2

IN 1 2 3 4

OUT 6

COMMON 5

VS5004 (REAR)

LOOPING

INPUT FROM OUTPUT FROM

OUTPUT

RECEIVER

MONITOR

COAXITRON® TRANSMITTER

(REAR)

Figure 13. VS5004 with Coaxitron Control

COAXITRON

RECEIVER

UP TO EIGHT RECEIVERS

CAMERAS

MON 1

ALARM

INPUT

COM

12 VAC

MON 2 MON X

INPUT

ALARM OUT

VS5008 (REAR)

LOOPING INPUT FROM OUTPUT TO

OUTPUT

RECEIVER

MONITOR

COAXITRON TRANSMITTER

(REAR)

NOTE: IN THIS CONFIGURATION, THE LOOPING OUTPUT (J8) IS UNTERMINATED.

Figure 14. VS5008 with Coaxitron Control

C808M-G (4/05)

Speciﬁcations

VIDEO

Inputs

Terminating (75 ohms) or looping

75 ohms

Outputs

Monitor 1

Monitor 2

VS5004

VS5008

Hi Z

75 ohms

Monitor X

VS5008

Coaxitron transmitter (nonampliﬁed) output

Unity

Gain

Dwell

Adjustable from 1-70 seconds nominal

Frequency

Response

Maximum

Signal Level

Tilt

Flat within +/-1 dB to 10 MHz

2 Vp-p

Less than 2%

Crosstalk

Better than -40 dB at 5.5 MHz

ELECTRICAL

Power Requirements

for Transformer

1.5 VA (0.125 A) at 12 volts RMS +/-15%, 50/60 Hz from a dedicated, isolated 120 or 230 VAC power

source. Wall transformer is provided with unit

NOTE: These units are also capable of operating on 12 VDC for mobile applications.

Connectors

Alarm In

BNC

Normally open relay contact, 10 V at 1 mA

Open collector

Alarm Out

GENERAL

Construction

Chassis

Cover

Steel, zinc plated

Steel, black polyester powder coat

Aluminum, black polyester powder coat with white silk screen

Panel

Environment

32° to 120°F (0° to 49°C)

Dimensions

VS5004

VS5008

1.75" H x 5.63" W x 8.75" D inches (4.45 x 14.30 x 22.23 cm)

1.75" H x 14.50" W x 8.50" D inches (4.45 x 36.83 x 21.59 cm)

Weight

VS5004

VS5008

2.5 lb (1.13 kg)

7 lb (3.17 kg)

Rating

Meets Nema Type 1 standards

C808M-G (4/05)

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or

workmanship for a period of one year after the date of shipment.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or

(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following

information:

Exceptions to this warranty are as noted below:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

•

Five years on FT/FR8000 Series ﬁber optic products.

Three years on Genex^®Series products (multiplexers, server, and keyboard).

If there is a dispute regarding the warranty of a product which does not fall under the

warranty conditions stated above, please include a written explanation with the product

when returned.

Three years on Camclosure^®and ﬁxed camera models, except the CC3701H-2,

CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and CC3651H-2X camera models,

which have a ﬁve-year warranty.

Method of return shipment shall be the same or equal to the method by which the item was

received by Pelco.

•

Two years on standard motorized or ﬁxed focal length lenses.

Two years on Legacy^®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series

ﬁxed dome products.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at

(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned

for credit, and RA number if returned for repair).

•

Two years on Spectra^®, Esprit^®, ExSite^™, and PS20 Scanners, including when used in

continuous motion applications.

•

Two years on Esprit^®and WW5700 Series window wiper (excluding wiper blades).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing

charge.

Eighteen months on DX Series digital video recorders, NVR300 Series network video

recorders, and Endura^™Series distributed network-based video products.

Goods returned for repair or credit should be clearly identiﬁed with the assigned CA or RA

number and freight should be prepaid. Ship to the appropriate address below.

•

One year (except video heads) on video cassette recorders (VCRs). Video heads will be

covered for a period of six months.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Six months on all pan and tilts, scanners or preset lenses used in continuous motion

applications (that is, preset scan, tour and auto scan modes).

Service Department

Pelco

3500 Pelco Way

Clovis, CA 93612-5699

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco

shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,

California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident

are not covered under this warranty.

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are

instructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from

the speciﬁc use or application made of the Products. Pelco’s liability for any claim, whether

based on breach of contract, negligence, infringement of any rights of any party or product

liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for

such Products. In no event will Pelco be liable for any special, incidental or consequential

damages (including loss of use, loss of proﬁt and claims of third parties) however caused,

whether by the negligence of Pelco or otherwise.

Pelco

3500 Pelco Way

Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors

473 Eccles Avenue

The above warranty provides the Dealer with speciﬁc legal rights. The Dealer may also have

additional rights, which are subject to variation from state to state.

South San Francisco, CA 94080 USA

Phone: 650-737-1700

Fax: 650-737-0933

REVISION HISTORY

Manual #

C808M

C808M-A

C808M-B

C808M-C

C808M-D

Date

7/87

2/91

4/90

9/92

4/95

Comments

Original version.

Updated format. Speciﬁcation section rewritten. Rack-mount instruction section dropped.

Incorporated addendum for dwell instructions.

Optional accessories updated. Changes to dwell adjustment procedure.

Added new Figure 5 drawing. Erroneous information on alarm operation (bridging) was deleted (ECO 94-222). Dwell internal timing changed from “3 to 70” to “1 to

70” seconds (ECO 93-062). Speciﬁcations updated. Two-column format.

C808M-E

C808M-F

C808M-G

6/98

12/99

4/05

Changed wiring color from blue to black in Figure 5. Changed manual format.

Added information on use with Coaxitron transmitter. Changed to new manual format.

Added VS5008 information from manual C809M-E.

Pelco, the Pelco logo, Spectra, Genex, Esprit, Camclosure, and Legacy are registered trademarks of Pelco.

Worldwide Headquarters

3500 Pelco Way

Clovis, California 93612 USA

USA & Canada

Tel: 800/289-9100

Fax: 800/289-9150

International

Tel: 1-559/292-1981

Fax: 1-559/348-1120

www.pelco.com

ISO9001

United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East

Perreaux Stereo Amplifier EP User Manual
Philips Cell Phone CD155 User Manual
Philips Indoor Furnishings P 5095 G User Manual
Philips Portable Speaker SPA5200 00 User Manual
Philips Work Light P 5722 C User Manual
Pinnacle Design TV Video Accessories TR4676FL User Manual
Pioneer Stereo Receiver VSX1017TXV User Manual
Planet Technology Switch FGSW 2620 User Manual
Pride Mobility Mobility Aid Jazzy Select 7 User Manual
ProForm Treadmill 1290 zlt User Manual