®
Installation/Operation
PCM5000
Light-Duty Camera Mount for the
MR5000 Series Public Viewing System
C226M (9/01)
01142
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150 • DataFAX (800) 289-9108
International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120 • DataFAX +1(559) 292-0435
PelcoEurope BV • Dillenburg Center, Dillenburgstraat 7C • 5652 AM Eindhoven • The Netherlands
Tel +31(40) 251-9870 • FAX +31(40) 251-9835
DESCRIPTION
The PCM5000 is a light-duty camera mount system designed specifically for Pelco’s MR5000 Series
Public Viewing System. The mount can be used with a CC3500, MC3500, CC3600 or MC3600 Series
camera. Video and power connections are integrated into the mount making installation quick and easy.
Pelco’s MR5000 Series Public Viewing System is specifically designed for retail applications to provide a
clear, visual warning to potential shoplifters that these premises are under surveillance. When properly in-
stalled the station is an effective deterrent against shoplifting.
INSTALLATION
1. Install the Camera Assembly onto the MR5000 Series Mount:
a. Remove the top or bottom end cap from the MR5000 Series monitor mount arm.
b. Pull video and electrical wire/cable for the camera out through the end of the mount arm.
Make all camera video and electrical connections.
c. Connect the camera assembly onto the end of the MR5000 Series monitor mount arm.
Tighten the mount arm set screws to secure the camera assembly.
2. Do the following to place the camera in the desired viewing position:
a. Loosen the collar set screws and adjust the ball and swivel assembly of the mount.
b. When the camera is in the ideal viewing position, tighten set screws to secure assembly.
COLLAR SET
SCREWS
MOUNT ARM
SET SCREW
[
]
Pelco Manual C226M (9/01)
3
WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date
of shipment. Exceptions to this warranty are as noted below:
•
•
•
•
Five years on Pelco manufactured cameras (CC3500/CC3600 and MC3500/MC3600 Series); two years on all other cameras.
Three years on Genex® Series (multiplexers, server, and keyboard).
Two years on all standard motorized and fixed focal length lenses.
Two years on Legacy®, Camclosure™ Camera Systems, CM6700/CM6800/CM8500/CM9500/CM9740/CM9750/CM9760 Matrix, DF5 Series
and DF8 Fixed Dome products.
•
•
•
•
Two years on Spectra® and Esprit™, including when used in continuous motion applications.
Two years on WW5700 series window wiper (excluding wiper blades).
Eighteen months on DX Series digital video recorders.
Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan
modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be
sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not
covered under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products.
Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability,
relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special,
incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence
of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation
from state to state.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number
(RA), and provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written
explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an
authorization number (CA number if returned for credit, and RA number if returned for repair). Goods returned for repair or credit should be
clearly identified with the assigned CA/RA number and freight should be prepaid. All merchandise returned for credit may be subject to a 20%
restocking and refurbishing charge.
Ship freight prepaid to: Pelco
3500 Pelco Way
Clovis, CA 93612-5699
® Pelco, the Pelco logo, Spectra, Genex, and Legacy are registered trademarks of Pelco.
™ Esprit and Camclosure are trademarks of Pelco.
© Copyright 2001, Pelco. All rights reserved.
REVISION HISTORY
Manual #
Date
Comments
C226M
9/01
Original version.
[
]
4
Pelco Manual C226M (9/01)
|