I N S T A L L A T I O N
TW3004P
Passive Four-Channel
Video Transceiver
C1665M-A (1/06)
Description
The TW3004P is a four-channel passive video transceiver that can transmit multiple video signals over
unshielded twisted pair (UTP) cable. The transceiver can be mounted into a fiber rack (RK5000PS-3U/
RK5000-3U). Each transceiver has four rubber feet for placement on a flat surface, such as a desk or
shelf.
The transceiver can be used at the camera and/or monitoring location. It allows for easy connectivity
with any video source or destination device, such as cameras, monitors, and matrix switchers. This
multichannel transceiver will transmit video (color/black-white) and Coaxitron® (up-the-coax) PTZ
control signals on the same pair of UTP wires.
Although the transceiver is passive and requires no power, the Pelco badge on the front of the unit illu-
minates when inserted into a fiber rack. The transceiver has built-in surge suppression.
PARTS OF THE TRANSCEIVER
ᕢ
ᕣ
ᕥ
4
2
3
1
ᕡ
ᕤ
Figure 1. TW3004P Parts
ᕡ Pelco Badge
ᕤ BNC Connector (4)
ᕢ 4-Pin Power Connector
ᕣ 8-Pin Terminal Block Connector
ᕥ Rubber Feet (4)
C1665M-A (1/06)
3
Installation
Make sure all parts are present for the unit.
1
1
Terminal block (with tension clamps)
Wall clip
MOUNTING
The TW3004P transceiver is three rack units high and can be mounted into a fiber rack or onto a wall
using a fiber wall mount kit or the supplied wall clip.
USING A RACK
You can mount a TW3004P into either an RK5000PS-3U or an RK5000-3U. For additional information,
refer to the RK5000PS-3U/RK5000-3U Fiber Rack Mount Chassis Installation manual.
USING WALL MOUNT KITS
The optional WM5001-3U wall mount base kit allows attachment of a single TW3004P to a wall.
Up to two WM5001-3UEXP wall mount expansion kits can be used to allow attachment of two
additional transceivers to the wall. For additional information, refer to the Fiber Wall Mount Kits
Installation manual.
USING A WALL CLIP
To attach the TW3004P transceiver to a wall using the supplied wall clip, refer to Figure 2 and do the
following:
1. Attach the wall clip to a wall using two screws (not supplied).
2. Slide the transceiver into the clip until the two holes on the bottom of the transceiver align with
the two holes on the lower flange of the clip.
3. Attach the transceiver to the clip using the two Phillips pan head screws provided with the clip.
4
C1665M-A (1/06)
UPPER
FLANGE
VERTICAL
MOUNTING HOLE (2)
HORIZONTAL
MOUNTING HOLE (2)
TW3004P
LOWER
FLANGE
SCREW, PHILLIPS
PAN HEAD WITH
LOCK WASHER (2)
WALL CLIP
Figure 2. Mounting the TW3004P Using the Wall Clip
APPLICATIONS
Figures 4 through 7 show how to use the transceivers in various applications. For example, the
TW3004P can be connected to a Spectra® or a Camclosure®. The terminal block on the back of the
TW3004P has tension clamps instead of screw terminals.
To connect the UTP wires to the terminal block:
1. Use a small screwdriver to open the clamps (+ and -) for each channel.
4
3
2
1
Figure 3. Terminal Block UTP Connections
C1665M-A (1/06)
5
Table A shows the distance in feet with Coaxitron or video only when using a particular type of
Cat cable. Table B shows the maximum allowable wire gauge for single wire and stranded wire.
Table A. Cable Distance
Distance
(with Coaxitron)
Distance
(video only)
Cable Type
Cat3
Cat5
Cat5e
Cat6
300 ft
500 ft
750 ft
750 ft
400 ft
650 ft
750 ft
750 ft
NOTE: Cat5e cable is recommended for optimum video performance.
Table B. Wire Gauge
Wire Gauge (maximum allowable)
24 AWG (1.5 mm2)
24 AWG (1.0 mm2)
Single Wire (solid)
Stranded Wire (flexible)
TW3004P
TW3004P
POWER CONNECTOR
FOR PELCO BADGE
UTP
4
2
4
2
3
1
3
1
MONITOR
FIXED CAMERA
Figure 4. Connecting Two Transceivers
6
C1665M-A (1/06)
10 PINS (5-/6+)
TW3004P
PIN 5 +
PIN 4 -
POWER CONNECTOR
FOR PELCO BADGE
FIXED CAMERA
8 PINS (4-/5+)
UTP
4
2
3
1
MONITOR
Figure 5. Connecting a UTP Camera to a UTP Receiver
NOTE: UTP cameras have a 10-pin RJ-45 connector. Standard RJ-45 connectors have 8 pins. Refer to
Figure 5 for correct pin outs.
C1665M-A (1/06)
7
TW3004P
VC-UTP BOARD
POWER CONNECTOR
FOR PELCO BADGE
SPECTRA
COAXITRON
UTP
4
2
3
1
MONITOR
VIDEO
MATRIX
Figure 6. Coaxitron PTZ Control
8
C1665M-A (1/06)
TW3004P
BLUE WIRE =
GRAY WIRE =
POWER CONNECTOR
FOR PELCO BADGE
CAMCLOSURE
UTP
4
2
3
1
MONITOR
Figure 7. UTP Camclosure to UTP Receiver
C1665M-A (1/06)
9
Specifications
ELECTRICAL
Power Source
Wire Type
Wire Category
12 VDC (for Pelco badge only)
Unshielded twisted pair (24 AWG maximum)
Cat3 or better
Wire Impedance
Wire Distance
100 ohms 20%
750 feet maximum
DC Loop Resistance
Differential Capacitance
Transient Immunity
Insertion Loss
52 ohms per 1,000 feet
19pF/ft max
300 W peak pulse power (8/20 US)
<1 dB; 0-8 MHz frequency range
VIDEO CHARACTERISTICS
Video Input/Output
Format
1, BNC; internally terminated in 75 ohms
NTSC, PAL, SECAM
Frequency Response
DC to 10 MHz
Common Mode/Differential
Mode Rejection
>60 dB typical
MECHANICAL
Connectors
BNC
Video input/output
8-Pin Terminal Block
4-Pin Connector
UTP input/output
Rack power for Pelco badge
Construction
Finish
Steel
Silver
GENERAL
Operating Temperature
Relative Humidity
Data Transmission
Dimensions
-40° to 185°F (-40° to 85°C)
0 to 90%, noncondensing
Supports Coaxitron up to 750 feet
8.75" D x 1.08" W x 4.81" H
(22.23 x 2.74 x 12.22 cm)
Unit Weight
1.46 lb (0.66 kg)
This equipment contains electrical or electronic components that must be recycled properly to
comply with Directive 2002/96/EC of the European Union regarding the disposal of waste
electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling
this equipment.
10
C1665M-A (1/06)
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of
shipment.
Exceptions to this warranty are as noted below:
•
•
•
•
Five years on FR/FT/FS Series fiber optic products and TW3000 Series unshielded twisted pair transmission products.
Three years on Spectra® IV products.
Three years on Genex® Series products (multiplexers, server, and keyboard).
Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and
MC3651H-2X camera models, which have a five-year warranty.
•
•
•
•
•
•
Three years on PMCL200/300/400 Series LCD monitors.
Two years on standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.
Two years on Spectra III™, Esprit®, ExSite™, and PS20 scanners, including when used in continuous motion applications.
Two years on Esprit and WW5700 Series window wiper (excluding wiper blades).
Two years (except lamp and color wheel) on Digital Light Processing (DLP®) displays. The lamp and color wheel will be covered for a period of
90 days. The air filter is not covered under warranty.
Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura™ Series distributed network-based video
products.
•
•
•
One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.
Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight
prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this
warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s
liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products
shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state
to state.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and
provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written
explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization
number (CA number if returned for credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate
address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the
following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco
Pelco c/o Expeditors
3500 Pelco Way
Clovis, CA 93612-5699 USA
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
REVISION HISTORY
Manual #
C1665M
C1665M-A
Date Comments
12/05 Original version.
1/06 Revised Table A.
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, Coaxitron, and Spectra are registered trademarks of Pelco.
Endura and ExSite are trademarks of Pelco.
©Copyright 2007, Pelco.
All rights reserved.
DLP is a registered trademark of Texas Instruments, Inc.
Worldwide Headquarters
3500 Pelco Way
Clovis, California 93612 USA
USA & Canada
Tel: 800/289-9100
Fax: 800/289-9150
International
Tel: 1-559/292-1981
Fax: 1-559/348-1120
ISO9001
Australia Canada Finland France Germany Italy Macau The Netherlands Russia Singapore
|
|
|
|
|
|
|
|
|
South Africa Spain Sweden United Arab Emirates United Kingdom United States
|
|
|
|
|
|