PLD58MUT
OWNER'S MANUAL
Mobile Video System
Motorized Slide Down And Detachable Panel
3.6 Inch Wide TFT Color Monitor
Car DVD/VCD/CD/MP3 Player/TV Tuner
AM/FM Digital Pll Tuning Radio
MPEG4 Player
USB Connect
Remote Control
SAFETY INFORMATION
CAUTION:
THIS DVD PLAYER IS A CLASS I LASER PRODUCT. HOWEVER THIS DVD
PLAYER USES A VISIBLE/INVISIBLE LASER BEAM WHICH COULD CAUSE .
HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE
THE DVD PLAYER CORRECTLY AS INSTRUCTED.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.DO NOT OPEN COVERS AND DO NOT
REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR MOISTURE.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, AND ANNOYING
INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES.
THIS DEVICE IS INTENDED FOR CONTINUOUS OPERATION.
This product incorporates copyright protection technology that is protected
by method claims of certain U.S. Patents and other intellectual property rights
owned by Macrovision Corporation and other rights owners.Use of this
copyright protection technology must be authorized by Macro vision Corporation,
and is intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
REGION MANAGEMENT INFORMATION:
This DVD Player is designed and manufactured to respond to the Region
Management Information that is recorded on a DVD disc. If the Region number
described on the DVD disc does not correspond to the Region number of this
DVD Player, this DVD Player cannot play this disc.
2
DISC NOTES
unusable) depending on your handle it
and conditions in the usage environment.
Note these scratches are not an
Disc formats supported by this
player
DVD
12 cm disc
V I D E O
indication of any problem with the player.
Label side
up
(Single-sided disc only)
Video CD
12 cm disc
CD
Do not touch
the
underside
of the disc
12 cm disc
MP3
12 cm disc
MP3
CD-RW
Do not
bend
Discs which cannot be played
with this player
DVD-ROM
DVD-R/DVD-RAM
CDV
Wipe the disc from
center
toward the outside
edge
CD-G
Handling and Cleaning
Dirt, dust, scratches and warping disc
will cause misoperation.
Do not place stickers or make
scratches on discs.
Preparing New Discs with Rough
Spots
A new disc may have rough edges on
its inside and outside edges.If a disc
with rough edges is used, the proper
setting will not be performed and the
player will not play the disc.Therefore,
remove the rough edges in advance
by using a ball point pen or pencil as
shown on the right.To remove the
rough edges, press the side of the pen
or pencil against the inside and outside
edges of the disc.
Do not warp discs.
A disc should always be kept in its
case when not in use to prevent from
damaging.
Do not place discs in the following
places:
1.Direct sunlight
2.Dirty, dusty and damp areas
3.Near car heaters
4.On the seats or dashboard
Rough spots
on
outside edge
Disc Cleaning
Use a dry soft cloth to wipe the surface.
If the disc is quite dirty, use a soft cloth
slightly moistured with isopropyl (rubbing)
alcohol. Never use solvents such as
benzine, thinner or conventional record
cleaners as they may mar the surface of
the disc.
Ball point pen
or pencil
Rough spots
on inside
edge
Note:
A disc may become somewhat scratched
(although not enough to make it
3
INSTALLATION
NOTES:
Choose the mounting location where the unit will not interfere with the normal
driving function of the driver.
Before finally installing the unit, connect the wiring temporarily and make sure
it is all connected up properly and the unit and the system work properly.
Use only the parts included with the unit to ensure proper installation. The use
of unauthorized parts can cause malfunctions.
Consult with your nearest dealer if installation requires the drilling of holes or
other modifications of the vehicle.
Install the unit where it does not get in the driver's way and cannot injure the
passenger if there is a sudden stop, like an emergency stop.
If installation angle exceeds 30 from horizontal, the unit might not give its
optimum performance.
30
Avoid installing the unit where it would be subject to high temperature, such
as from direct sunlight, or from hot air, from the heater, or where it would be
subject to dust, dirt or excessive vibration.
DIN FRONT/REAR-MOUNT
This unit can be properly installed either from "Front"(conventional DIN
Front-mount) or "Rear"(DIN Rear-mount installation, utilizing threaded
screw holes at the sides of the unit chassis). For details, refer to the following
illustrated installation methods.
4
INSTALLATION
DASH BOARD
HEX NUT
METAL MOUNTING
STRAP
SPRING WASHER
PLAIN WASHER
TAPPING SCREW
CONSOLE
SLIDE BRACKET
HOUSING
HEX BOLT
KEY PLATE
PLASTIC COVER
KEY PLATE
If you want to take CHASSIS out of the SLIDE BRACKET HOUSING,
first remove the PLASTIC COVER of the both sides away, then insert
the two KEY PLATE into left and right side of chassis as above illustration.
5
INSTALLATION
How To Remove And Install The Front Panel
When detaching or attaching the control panel, be careful not to damage the
connectors on the back of the control panel and on the panel holder.
Detaching The Control Panel
Before detaching the control panel, be sure to turn off the power.
1.Press the release button and the left hand side of the front panel will release.
(FIG. 1)
2.Pull-off the front panel (FIG. 2) and keep the front panel into the case (FIG. 3)
Install The Front Panel
First insert the right hand side of the front panel into the housing of the unit , then
push the left hand side of the front panel and make sure the panel is properly
installed(FIG.4),and then press the PWR button (2) briefly to switch the device ON.
FRONT PANEL
FRONT PANEL
RELEASE BUTTON
FIG.1
PROTECTIVE CASE
FIG.2
Installing The Front Panel
FRONT PANEL
FIG.4
FIG.3
6
CHAGNE ANGLE
CHANGING THE CONTROL PANEL ANGLE
When you want to change the viewing angle of the operating unit to play,
you can press the
as follows:
(angle)button repeatedly to select the desired angle
Angle 1
Angle 2
Angle 4
Angle 3
Caution:
Do not insert your finger behind the control panel.
7
ELECTRIC CONNECTION
WIRING CONNECTION
MAIN UNIT
(B+)12V
REAR CAMERA SWITCH
WHITE
GREEN
(B-)PARKING BRAKE
TV ANT IN
YELLOW
REAR CAMERA INPUT
AUX(optional)
VIDEO IN YELLOW
RCH IN RED
ANTENNA CONNECTOR
LCH IN WHITE
RCA CABLE
GREY SUBWOOFER
VIDEO OUT 2 YELLOW
IGNITION RED
SWITCH(B+)
COAXIAL OUT BROWN
RCH RED
REAR RCA OUTPUT
CABLE (optional)
CHOKE
BOX
MEMORY
BACK-UP(B+)
YELLOW
BLACK
LCH WHITE
FRONT RCA OUTPUT
CABLE
FRONT RCA RED
VIDEO OUT 1 YELLOW
FRONT RCA WHITE
R
GROUND(B-)
L
(FOR RCA LINE OUT VERSION ONLY)
FUSE
AUTO
ANTENNA
BLUE
GREY
WHITE
FRONT
FRONT
Rch SPK.
Lch SPK.
WHITE/BLACK
GREY/BLACK
VIOLET
REAR
GREEN
REAR
Rch SPK.
Lch SPK.
GREEN/BLACK
VIOLET/BLACK
Note:
the earth connection cable (parking brake B-) must be connected in order for DVD
pictures to be played back to the monitor. If the cable has not been correctly
connected, the message “PARKING BRAKE” appears on the monitor.
8
REMOTE CONTROL
15
16
3
17
7
5
1
19
2
13
20
21
22
6
23
12
14
24
18
9
25
11
10
26
4
8
Press it to change the display to clock display.
Press it to change between TV, RADIO ,DISC and AUX IN mode.
Press it to stop playback.
1.CLK
2.MODE
3.STOP
4.SETUP
5.MO/ST(AUDIO)
Display the SETUP menu.
In radio mode, press it to select STEREO or MONO mode (In disc
mode, press it to changing of the AUDIO soundtrack on multi-
audio soundtrack DVD disc. Changing of the sound mode of the
VCD/CD disc)
Changing of the SUBTITLE language on multi-subtitle language
DVD disc. In radio mode,.Press this button for distance reception
when you are located at weak signal location, depress it for
stronger signal.
6. SUBTITLE
LO/DX
Switch the Repeat mode of DVD/VCD/CD/MP3 disc.
Disc search button, cooperatively used with numeric buttons
7.REPEAT
8.GOTO
Press
to skip to the next track & press
to skip back one track.
9.
/
(Note:In DVD mode, press continually the twice to skip back one track.)
Press it repeatedly to change mode through volume , bass, treble,
balance , fader, color, bright, contrast and tint modes.
Press it to adjust volume level
10.SEL
11. VOL+/VOL-
12.
Cursor buttons in MENU mode. Note: For models without built-in
/
/
/
FM Modulator, the
control. In TV mode, press
to select channel upward and downward.
/
buttons can be used for volume up/down
/
to fine tune. Press the
/
Press it to display the root menu of the DVD disc. Press it long to switch
the Subwoofer ON and OFF.
Display statistical disc information during playback (To change
the band in radio stations)
13.MENU
SUB WOOFER
14.BAND(OSD)
Press it to turn on the unit ,press it again to turn off.
Press once to pause a play, press again to resume playback.
Press it to mute down sound.
15.POWER
16.PLAY/PAUSE
17.MUTE
Display the TITLE menu that is stored in DVD disc changing
between PBC ON and PBC OFF on the VCD disc.(Auto store
and preset scan function in radio stations .)
Press it to change the view angle.
18.TITLE/PBC
(A/P)
19.
Changing of the view angle on multi-angle DVD disc.
Press it to turn to equalization function.
20.ANGLE
21.EQ
22.SEARCH
In TV mode, Press it to search TV channel automatically.
In DISC mode, Press it to start forward rapidly.
Confirm the Track/Chapter selected with the number key or
selected with the cursor buttons on TV screen.
In TV mode, press it to ADD and DELETE channel .
In DISC mode, press it to reverse rapidly
23.ENTER
24.SKIP
Numeric buttons.
Tens digit select button, cooperatively used with numeric buttons.
Six preset memory buttons.
25. 0 - 9
26.+10
27. RADIO PRESET
9
REMOTE CONTROL
Preparing the Remote Control
Inserting the Batteries
1.First push to inside as the direction indicated by the arrow (See
1
)And then
).
Remove the battery holder as the direction indicated by the arrow (See
2
2.Replace the battery Set a new battery property with (+)side up as illustrated
(See ).
3
4
3.Insert the battery holder. Push in the holder to the original position(See
).
Using the Remote Control
Face the remote control towards the player front face IR mark (remote control signal
receiver).
Operation angle: About 30 degree in each the direction of the front of the IR mark.
10
BASIC OPERATION
1
3
18
15 14 11 6 13
5
10
SEL
4
8
12
16
9
17
7
2
1.REL BUTTON
Press the REL button to detach the removable front panel.
2.PWR On/Off BUTTON
Press this button to switch the device On, WELCOME appears in the display.
Press it again to switch the device Off, SEE YOU appears in the display.
3-4.VOL+/VOL- & SEL BUTTON
Press SEL(4) button briefly to across the sound/picture mode selection menu
by repeatedly pressing the SEL button you can select the individual menu items
such as volume, bass, treble, balance, fader, color, bright, contrast and tint .
Then rotate the VOL + / - to adjust the selected mode.
(The corresponding value will show on the display.)
When mode has not been adjusted for several seconds, display returns to normal
radio or CD display.
Volume
Bass
Treble
Balance
Fader
Tint Contrast
Bright
Color
A.Volume:Adjust volume level by using VOL + / - button.
Note: The unit is initially set to volume mode.
B.Bass:Press SEL button one time. Adjust bass level by using VOL + / - button.
C.Treble:Press SEL button two times. Adjust treble level by using VOL + / -button.
D.Balance:Press SEL button three times. Adjust sound balance between left
and right speakers by using VOL + / VOL - button.
E.Fader:Press SEL button four times. Adjust sound balance between front and
rear speakers by using VOL + / VOL - button.
(NOTE: the function of the Color, Bright, Contrast and Tint. Please see 16 page.)
5. BAND BUTTON
In RADIO mode, press the BAND button on the front panel or on the remote
controller to select your desired radio band and word which band is selected
will be displayed in the TFT . Press it to change the bands as below :
FM
MW
LW
FM
MW
FM
AM
For 3 Bands (Europe)
For 2 Bands (Europe)
For 2 Bands (USA)
11
BASIC OPERATION
6. EQ BUTTON
Swing the SEL knob in the direction of the EQ to turn to equalization function and
to select desired audio mode. There are four kinds of mode as below:
JAZZ
CLAS
POP
ROCK
7. APS/DISP BUTTON
In Radio Mode:
a) Memory function:
swing the SEL knob in the direction of APS/DISP for approximately 2 seconds
to active automatic station storage. The radio searches within the current
frequency band, e.g. FM1, for the strongest station are then allocated to the
corresponding storage locations. Then the station of the first storage location
is set. If you would like to search for more stations in the FM band, press the BND
button(5) in order to change to the FM2 or FM3 band. Swing the SEL button (4)
again in the APS/DISP direction for about 2 seconds to continue search.
b) Scan Function:
if the SEL knob is moved briefly in the direction of APS/DISP, the radio briefly
plays all the preset stations of the frequency band. (The scan function ends
automatically at the first storage location of frequency band FM1.)
In Disc Mode:
swing the SEL knob briefly in the direction of the APS/DISP on the front panel ,
the playback picture (the monitor on the unit only) will not to be shown, only the
audio will be heard. (Swing it again to resume the playback picture mode.) You
can press SEL knob briefly to select the “BG COLOR” by repeatedly pressing the
SEL knob, then rotate the VOL+/- to select the background color among of the
“AUTO, BG COLOR: 01........BG COLOR: 11”, in “ AUTO” mode, the monitor of
unit will change the background color automatically. also you can select the TV
system ( only in EUR frequency mode) among of the “PAL BG”, “PAL DK”, “PAL I”,
“PAL MN” by using the VOL+/VOL- .
8. MU BUTTON
Press it button to switch of the loudspeakers for a short period. The word MUTE
flashes in the display. Press it again to cancel the mute function. This function
can also be cancelled by rotating the VOL multifunction button.
9.
(ANGLE)BUTTON
you can change the viewing angle of the operating unit . Press this button up to
four times in order to select the desired position.
10.
BUTTON
button to interrupt playback of the CD (pause function). Press this
button again to cancel this function.
Press the
11.
/
a) In DISC, USB mode:
BUTTONS (TUNE, SEEK, TRACK, SKIP UP/DOWN)
if you wish to jump forwards or backwards press the SEL button (4) briefly in
the or direction. (Note: in DVD mode, press the SEL button continually
twice in direction to skip back one track during playback.)
Note:For some VCD 2.0 dics(PBC-playback control),
be unavailable.
and
buttons may
12
BASIC OPERATION
To wind through the tracks keep the SEL button pressed in the or direction
for about 2 seconds. FF X2 appears in the display. Operating the SEL button
again, the speed of rapid forward/reverse changes according to the disc
as follow:
DVD/VCD/CD/MP3:
Normal Playback 2x
4x
8x
16x
b) In Radio Mode:
Move the SEL button in the direction of
or
in order to set a radio station
or direction in order to
manually. Keep the SEL taste pressed down in the
start the search for a radio station automatically.
12. MOD BUTTON
Press it repeatedly to select TV, AUX IN , RADIO and DISC mode.
During the USB playback, you can press STOP button and then press GOTO
button to select the DISC mode.
13.
(EJECT) BUTTON
Press this button to insert and eject the Disc . The operating unit swings down-
wards. Insert the Disc with the labelled side facing upwards gently into the CD
slot until the device draws in the CD/DVD automatically. The operating unit will
automatically swings back to the normal position.
14. RESET BUTTON
RESET button is placed on the housing and must be activated with either a
ballpoint pen or thin metal object. The RESET button is to be activated for the
following reasons:
A. Initial installation of the unit when all wiring is completed.
B. All the function buttons do not operate.
C. Error symbol on the display.
Note:If press RESET button , the unit can't work yet, please use a cotton swab
soaked in isopropyl alcohol to clean the socket on the back of the front panel.
15. IR (infrared)
Sensor for the remote control.
16. AUX IN SOCKET
The operation of the AUX , please see page 15.
17. USB CONNECT LINE SOCKET
The operation of the USB, please see page 17.
18. TFT Display (liquid crystal display)
The operation of the TFT, please see page 16.
13
BASIC OPERATION
TOP/RPT/INT/RDM FUNCTION (Only for the RC.)
A.To memorize the current frequency, press any one of the six preset buttons[1-6]
on the remote controller hold for more than 2 seconds.
B.To recall the preset memory, press one of the preset buttons [1-6].
C.Press 1/TOP button to select the first track/chapter to play.
a. In the state of VCD/CD/MP3 disc playing, press the button to select the
first track/chapter to play.(depend on the disc used for VCD)
b. In the state of DVD disc playing, the 1TOP button is not available.
D.Press REPEAT button briefly to select repeat mode as follow.
VCD/CD/MP3:
REP-ONE
DVD:
CHAPTER REPEAT ON
TITLE REPEAT ON
REP-ALL
REPEAT OFF
a. Continuously repeat at the current chapter/track, when selected
REP-ONE mode.
b. Select REP-ALL mode to continuously repeat all chapter/track on the
current disc.
c. REPEAT feature does not support VCD2.0 (with PBC ON).
E.Long Press 3/INT button to scan disc.
a. In the state of CD disc playing, press the 3/INT button to play the previous 6
seconds part of each track/chapter on disc.
b. In the state of Mp3 disc playing, the 3/INT button is not available.
c. In the state of VCD disc playing , long press the 3/INT button, the screen will
display as follow (long press it again will release this mode.):
SELECT DIGEST TYPE:
TRACK DIGEST
DISC INTERVAL
TRACK INTERVAL
/
/
/
1). you can use the
and then press the ENTER button to confirm .
2). In Track Digest OR Disc/Track Interval MODE.
You can use the buttons to select the items ,and then press the
ENTER to confirm .
buttons on the remote control to select the item,
/
/
/
You can also select the items using the corresponding number buttons, and
then press the ENTER to confirm .
d. In the state of DVD disc playing , long press the 3/INT button, the screen will
display as follow (long press it again will release this mode.):
SELECT DIGEST TYPE:
TITLE DIGEST
CHAPTER DIGEST
TITLE INTERVAL
CHAPTER INTERVAL
1). you can use the
and then press the ENTER button to confirm .
2). In Title/Chapter Digest OR Title/Chapter Interval MODE.
You can use the buttons to select the items ,and then press the
ENTER to confirm .
buttons on the remote control to select the item,
/
/
/
/
/
/
You can also select the items using the corresponding number buttons, and
then press the ENTER to confirm .
F. Long Press 4/RDM to play disc in random.
In the DVD/VCD/CD/MP3 disc playing, press the 4/RDM button on the front
panel to play in random (depend on the disc used for VCD).
14
BASIC OPERATION
MP3/WMA/JPEG DISC PLAY
1.When inserting an MP3/WMA/JPEG disc. Ex: When Mp3 file is detected.
4
5
6
1 .Current track(file)(highlighted bar)
.Current track (file) number/total
number of tracks(files) in the current
folder.
2
00:56
04:07
3
2
Repeat one
003/112
.Elapsed playing time of the current
track(not available for JPEG disc)
.total playing time.( not available for
JPEG disc)
3
4
Mp3
K
P
Mp3
Mp3
1
woman 1
ton
.Selected playback mode
.Operation mode icon.
5
6
..........n..e.w.
(Play),
(stop), (pause), (forward)
(reverse).
on the remote control to select the item or folder,
In stop mode , use
/
then press ENTER button to confirm.
Pressing REPEAT button repeatedly can select two kinds of repeat play mode.
2.REP-ONE:
Play the same song over and over again.
3.REP ALL:
Play all songs in the discover and over again.
In the playback, use
In the playback, face right or left swing the SEL knob
seconds ) on the front panel or short press
forward/reverse.
or
to skip an item ahead or back.
button (more than2
on the remote control to rapid
/
/
AUX IN Socket ( 16 )
To connect analogue replay devices. Use this jack to replay sound of other replay
equipment such as DVD players, computers, etc. Via the loudspeakers.
1). Please connect the external device with stereo jack plug the AUX IN socket.
2). Press the MOD button(12) to select the AUX IN connection.
3). Rotate the VOL+/- button (3) you can change the volume level.
ALTERNATE AUDIO/VIDEO SOURCE
To connect analogue replay devices. Use this jack to replay sound of other replay
equipment such as DVD players, computers, etc. Via the loudspeakers. (See fig.1)
1). Please connect the external device with stereo jack plug the Aux In socket(16).
2). Press the MOD button to select the AUX IN connection.
3). Use the buttons on the external device to operate the item of the playing.
Headphones
port
( fig.1)
( connect cable)
15
BASIC OPERATION
TFT MONITOR OPERATION
Press SEL(4) button briefly to across the sound/picture mode selection menu
by repeatedly pressing the SEL button you can select the individual menu items
such as volume, bass, treble, balance, fader, color, bright, contrast and tint .
Then rotate the VOL + / - to adjust the selected mode.
(The corresponding value will show on the display.)
When mode has not been adjusted for several seconds, display returns to normal
radio or CD display.
Volume
Bass
Treble
Balance
Fader
Tint Contrast
ADJUSTABLE ITEMS:
COLOR: 0 to 32
Bright
Color
Adjust the color fo the picture-lighter or darker.
BRIGHT: 0 to 32
Adjust if the picture is too bright or too dark.
CONTRAST: 0 to 32
Adjust the contrast of the bright ans dark portion.
TINT: 0 to 32
Adjust the tint if the human skin color is unnatural.
-Adjustable when “NTSC “ is selected for “NTSC/PAL “ .
(The function of the VOLUME, BASS, TREBLE, BALANCE and FADER, Please
see page 11.)
REAR VIEW CAMERA
When connecting the rear view camera.the mirror image of the rear view through
the rear view camera is automatically displayed on the monitor when you change
the gear to the back position.(The monitor on the unit only.)
NOTE(for the brake function)
if the parking brake is not engaged,“parking brake” flashes on the monitor,
and no playback picture will be shown. Only the audio will be heard.
-This warning appears only when the parking brake wire is connected to the parking
brake system built in the car. (See page .8)
MPEG4 DISC PLAY
MPEG4 disc is playing as the format
00:56
04:07
Repeat one
of FILE . For example:
In stop mode , use
001/001
/
on the
remote control to select the item ,
then press ENTER button to confirm.
Pressing REPEAT button repeatedly can
select three kinds of repeat play mode.
REP-ONE:
MAY-AUG
C14-Long-fright
..............
Play the same song over and over again.
REPEAT ALL:
Play all songs in the current directory in sequence, over and over again.
DISC REPEAT:
Play all songs in the discover and over again.
In the playback, use
In the playback, face right or left swing the SEL knob
and keep more than 2 seconds or short press
forward/reverse.
or
to skip an item ahead or back.
button on the front panel
on the remote control to rapid
/
/
16
BASIC OPERATION
USB Operation
On-Screen Display Function
Press the OSD button during playback
to display the contents of the current
disc on the screen.
A.Example for DVD:
a.Press OSD for the first time:
A.Plug the USB connect line to the USB
socket (see number 17) of the unit
properly,(See fig.1) when the USB
appliance connect to the USB port of
the connect line, the system star
playing track of the USB appliance
automatically.
TITLE ELAPSED
TT 01/01 CH 01/38
0:02:06
B. IN USB playing , you can press the
cursor button to select the item.Then
press ENTER button to playing.
also press numeric to play the
Title Number, Total Title Number,
Chapter Number, Total Chapter
Number of this Title of the disc
currently being played will be shown
on the screen,along with the elapsed
time.
corresponding track directly. Press
the
track or skip to the back one track
Press the button to fast forward
or fast reverse.
/
button to skip to the next
b.Press OSD for the second time:
/
TITLE REMAIN
TT 01/01 CH 01/38 3:24:36
Press the REPEAT button to select
repeat play mode.
You can press the EJECT button to
eject the disc or insert the disc into
the compartment.
When insert the disc, the unit will
play the disc automatically .
C.In USB mode(when the disc in the unit)
Press the STOP button once , and
then press the GOTO button, the unit
will change the DISC mode to play,
In DVD/VCD/CD mode,
c.Press OSD for the third time:
CHAPTER ELAPSED
TT 01/01 CH 01/38 0:02:56
d.Press OSD for the fourth time:
CHAPTER REMAIN
TT 01/01 CH 01/38 0:04:32
e.Press OSD for the fifth time:
The message on the screen will be
cleared.
Press the STOP button twice, and
then press the GOTO button, the unit
will change the USB mode to play
In MP3 mode,
B.Example for VCD/SVCD/CD:
a.Press OSD for the first time:
press the STOP button once, and
then press the GOTO button, the unit
will change the USB mode to play.
Note:
SINGLE ELAPSED
TRACK 01/16
00:49
a:To prevent damage to the USB ,
during the playback don`t pull out.
b.Press OSD for the second time:
SINGLE REMAIN
b:In the state of the DISC playing ,
Best to pull out the USB.
TRACK 01/16
02:45
c.Press OSD for the third time:
TOTAL ELAPSED
TRACK 01/16
00:60
USB port
d.Press OSD for the fourth time:
TOTAL REMAIN
(USB connect line)
TRACK 01/16
78:46
(Fig.1)
17
BASIC OPERATION
Notes:
- The language number is different
according to the disc.
- Some discs only contain one subtitle
language.
- When no different subtitle language
e.Press OSD for the fifth time:
The message on the screen will be
cleared for SVCD and VCD.
C.Example for MP3:
Each time OSD is pressed, the
message displayed on screen changes
as follows:
are recorded, will be displayed
at screen left top corner.
SINGLE ELAPSED
SINGLE REMAIN
Multi-angle Function
Multi-audio Language Function
For DVD:
Press AUDIO during playback.
Each time the button is pressed,
number of the audio soundtrack
language changes on sequential order.
NOTES:
(for DVD Only)
Press ANGLE during playback. Each
time the button is pressed, number of
the angle changes in sequential order.
Notes:
- The angle number is different
according to the disc.
- The function only work for disc having
scenes recorded at different angles.
- When no different angle are recorded,
will be displayed at screen left top
corner.
- The language number is different
according to the disc.
- Some disc only contain one language
soundtrack
- When no different language
soundtrack are recorded
will be
display at screen left top corner.
For VCD/CD:
Press AUDIO during playback. It is
possible to switch the sound between
monaural and stereo sound.
TV Operation
Switching to TV mode
1.Connect the TV antenna to the TV.IN
(from Ant) jack on the back of the unit.
2. Press the mode button on the remote
control to select the TV mode.
Auto searching TV channels
Press the SEARCH button on the remote
controller to star search channel
automatically.
MONO LEFT
MONO RIGHT
MIX-MONO
STEREO
Title Menu Function
For DVD:
If the DVD has multiple titles recorded
on the disc. It can select preferred title
from the title menu to start playback.
- Press TITLE during playback.The title
menu is display.
- Press the cursor button shown in TV
screen, select preferred title by the
cursor button and confirmed by
ENTER key.
Selecting channel
- Press the
/
button to choose the
channel upward and downward.
- The numeric button (0-9) allow you to
select the corresponding channel directly.
Note:
In TV mode, the +10 button is not available.
Fine TV channel
You can press
/
button on the remote
For VCD:
controller to fine TV channel. It can be
improve the picture quality .
Channel ADD/DEL
In TV mode ,after search channel
automatically, when you want delete the
no sign channel, press the SKIP button (the
screen display SKIP),the channel will be
deleted. Also, you can press numeric button
to select channel, then press SKIP to add
channel(the screen display SAVE).
Press TITLE/PBC button on the remote
control while the disc is playing, you can
switch between "PBC on"and "PBC off"
mode.
Multi-subtitle Language Function
(for DVD Only)
Press SUBTITLE during playback.
Each time the button is pressed, number of
the subtitle language changes in
sequential order.
18
SETUP
GENERAL SETUP
--- GENERAL PAGE ---
DOLBY
DOLBY
-----General setup page----
-----General setup page----
TV Display
Normal/PS
Normal/LB
Wide
TV Display
LB
ON
Angle Mark
OSD Lang
Spdif Output
Captions
Angle Mark
OSD Lang
Spdif Output
Captions
ENG
SPDIF/RAW
ON
Screen Saver
Last Memory
Screen Saver
Last Memory
ON
ON
Set TV Display Mode
Go To General Setup Page
TV Screen
Video
Material
1. Press SETUP button on the remote
control .
Wide(16:9)
Pan Scan
Normal
Letter-box
4:3
2.The SETUP menu is displayed.
3.Select the preferred item by using the
/
/
/
buttons
4.Press ENTER button.
a.GENERAL SETUP
1.TV DISPLAY SETUP
This setup page includes the item
of TV display & audio output feature.
The detail please refer to
This is to select the appropriate TV
aspect (4:3 or 16:9) according to the
connected TV set.
GENERAL SETUP MENU.
b.SPEAKER SETUP
Normal/PS (For 4:3 TV)
Played back in the PAN & SCAN style.
(If connected to wide-screen TV, the
left and right edges are cut off.)
Normal/LB (For 4:3 TV)
This is to activate the audio output
from DOLBY AC3 5.1 DOWNMIX
to 2 channel mode. Please refer to
SPEAKER SETUP MENU.
c.DOLBY DIGITAL SETUP
Please refer to DOLBY DIGITAL
SETUP.
Played back in letterbox style.
(If connected to wide-screen TV, black
bands appear at top and bottom of the
screen.)
d.PREFERENCE SETUP
This setup page includes all the
configuration of support feature.
The detail please refer to
Wide (For 16:9 TV)
Select when a wide-screen TV set is
connected.
PREFERENCES SETUP MENU.
19
SETUP
DOLBY
DOLBY
-----General setup page----
TV Display
-----General setup page----
TV Display
ON
Angle Mark
OSD Lang
Spdif Output
Captions
Angle Mark
Osd Lang
OFF
SPDIF OFF
SPDIF/RAW
SPDIF/PCM
Spdif Output
Captions
Screen Saver
Last Memory
Set Angle Mark
Screen Saver
Last Memory
Setup SPDIF
2.ANGLE MARK DISPLAY SETUP
If it is set to ON, when the multi-angle
4.SPDIF OUTPUT
This is to activate the audio output
from SPDIF OFF mode to SPDIF/RAW
mode to SPDIF/PCM mode.
DVD disc is playing,
(the angle
mark) will appears on the screen; if is
set to OFF, the mark will not appear.
DOLBY
DOLBY
-----General setup page----
TV Display
-----General setup page----
TV Display
English
French
Angle Mark
OSD Lang
Spdif Output
Captions
Angle Mark
OSD Lang
German
Spanish
Italian
ON
Spdif Output
OFF
Captions
Screen Saver
Last Memory
Screen Saver
Last Memory
Closed Caption
Portuguese
Set OSD Language
5.CAPTIONS SETUP
3.OSD LANG TYPE SETUP
Select the preferred OSD language
Activate the CAPTIONS feature by
selecting ON. And release this feat-
ure by selecting OFF.
by using the
/
buttons.
20
SETUP
SPEAKER SETUP
--- SPEAKER SETUP PAGE ---
DOLBY
DOLBY
-----General setup page----
TV Display
-----Speaker Setup Page----
Angle Mark
OSDLang
Spdif Output
Captions
DOWNMIX
LT/RT
STEREO
ON
Screen Saver
Last Memory
Screen Saver
OFF
Set Downmix Mode
This is to activate the audio output from
DOLBYAC3 5.1 DOWNMIX to 2 channel
mode. Select the preferred SPEAKER
connection by using the cursor buttons.
Select the LT/RT to activate the Dolby
surround compatible output.
6.SCR SAVER SETUP
Select the SCR SAVER output
ON/OFF.
Select the STEREO to activate simple
stereo mode.
DOLBY
DOLBY DIGITAL SETUP
DOLBY
-----General setup page----
TV Display
-----Dolby Digital Setup----
Angle Mark
OSD Lang
Spdif Output
Captions
FULL
6/8
DYNAMIC
4/8
2/8
ON
Screen Saver
OFF
OFF
Last Memory
Set Last Memory State
Set DRC OFF
DYNAMIC RANGE CONTROL
Select DRC and adjust the dynamic
range of a Doby Digital encoded
7.LAST MEMORY SETUP
Select the LAST MEMORY output
ON/OFF.
program. There are 8 steps between
full compression and off compression.
21
SETUP
PREFERENCES SETUP
--- PREFERENCES PAGE ---
DOLBY
DOLBY
-----Preference Page----
-----Preference Page----
TV Type
PAL
TV Type
English
French
Spanish
German
AUTO
NTSC
Audio
Audio
Subtitle
Disc Menu
Parental
Password
Default
Subtitle
Disc Menu
Parental
Password
Default
Italian
Portuguese
OFF
Set TV standard
Preferred Subtitle Language
1.TV TYPE SETUP
3.SUBTITLE LANGUAGE SETUP
Select the preferred SUBTITLE
language by using the cursor buttons.
This player can play discs recorded
in either PAL or NTSC format.Select
NTSC format, when you connected to
NTSC TV.Select PAL format, when
you connected to PAL TV.Select AUTO
format, the player TV output format
will according to the DVD disc format..
DOLBY
DOLBY
-----Preference Page----
TV Type
-----Preference Page----
TV Type
Audio
English
English
Audio
French
Subtitle
French
Disc Menu
Parental
Password
Default
Spanish
German
Italian
Subtitle
Spanish
Disc Menu
German
Parental
Italian
Portuguese
Password
Portuguese
Default
Preferred Menu Language
Preferred Audio Language
4.DISC MENU LANGUAGE SETUP
Select the preferred DISC MENU
language by using the cursor
buttons.
2.AUDIO LANGUAGE SETUP
Select the preferred AUDIO sound-
track by using the cursor buttons.
22
SETUP
DOLBY
DOLBY
-----Preference Page----
-----Preference Page----
TV Type
1KID SAF
2G
TV Type
Audio
Audio
3PG
Subtitle
Disc Menu
Parental
Password
Default
Subtitle
4PG13
5PGR
6R
Disc Menu
Parental
Password
Default
7NC 17
8 ADULT
OFF
RESET
Load Fcatory Setting
Set Parental Control
7.DEFAULTS
Select reset to become factory initial
setting.
5.PARENTAL
Select suitable parental guidance by
the cursor buttons and conformed by
pressing ENTER button.
DEFAULTS TABLE
DOLBY
TV DISPLAY
NORMAL/LB
ON
-----Preference Page----
TV Type
ANGLE MARK
OSD LANGUAGE
ENGLISH
SPDIF/RAM
ON
GENERAL SETUP
Audio
SPDIF OUPUT
CAPTIONS
Subtitle
Disc Menu
Parental
SCR SAVER
ON
LAST MEMORY
ON
DOWNMIX
SPEAKER SETUP
DOLBY DIGITAL
STEREO
OFF
Password
Default
CHANGE
DYNAMIC
TV TYPE
AUDIO
AUTO
ENGLISH
OFF
Change Password
SUBTITLE
6.PASSWORD
DISC MENU
Select the change and press ENTER
button. Type the old password (The
initial factory code is 1379) and key
in 4 characters password now you
want to use, and retype again to
confirm key in correctly.
PREFERENCES
ENGLISH
8 ADULT
1379
PARENTAL
PASSWORD
23
SPECIFICATION
GENERAL
Supply Voltage
Current Consumption
SIGNAL SYSTEM
: 12v Dc (11v-15v)
: More Then 10 A
: Compositive Video 1.0vp-p 75
DISCS PLAYED
(1) Dvd-video Disc
5"(12 Cm) Single-sided, Single-layer
5"(12 Cm) Single-sided, Double-layer
(2) Compact Disc (cd-da, Video Cd)
5"(12cm) Disc
AUDIO SIGNAL OUTPUT
CHARACTERISTICS
: 2ch&4ch Line Out
(1) Frequency Response 20 Hz - 20 Khz
(2) S/n Ratio
90 Db (jis)
(3) Wow And Flutter
Below Measurable Limits
RADIO
FM TUNER SECTION
Tuning Range
: 87.5-107.9MHz
: 10.7MHz
IF Range
Usable sensitivity(30dB)
AM TUNER SECTION
Frequency Range
IF Range
: 15dB
: 530-1710KHz
: 450KHz
Usable sensitivity(30dB)
: 45dB
TV TUNER
TV System
TV Sensitivity
: NTSC or PAL
:
TFT MONITOR
Monitor Screen Size
Number of Pixels
Color System
: 3.6 Inch Wide
: 960 X 234 pixes
: NTSC/PAL
NOTE:
Specifications and design are subject to modification, without notice, due to
improvements in technology.
24
TROUBLE SHOOTING
Before going through the check list, check wiring connection. If any of the problems
persist after check list has been made, consult your nearest service dealer.
SYMPTOM
CAUSE
SOLUTION
If the power supply is properly
connected to the car accessory
terminal,switch the ignition key
to "ACC"
The car ignition switch is
not on
No power
The fuse is blown
Replace the fuse
Presence of disc inside the Remove the disc in the player,
player.
then put a new one
Inserting the disc in reverse Insert the compact disc with
direction
Disc can not be
loaded or ejected
the label facing upward
Clean the disc or try to play a
new one
The disc is extremely dirty
or defective
Temperature inside the car
is too high
Cool off or until the ambient
temperature return to normal
The color system is
set incorrectly
Television/video
imageappears
black-white
Please switch to correct color
system from menu
Make proper connection
The unit is not connected
to the parking brake
detection switch
No television/video
image appears
according to“wire connection”
For safety reasons no television
/video images are displayed while
the vehicle is moving.
The parking brake is not
engaged
Engaging the parking brake will
cause images to be displayed.
Please the television mode of
the choice accommodation
The disc format is not
accordingto the TV-set
used (PAL/NTSC)
No color in picture
No JPEG files are recorded
on the disc.
JPEG disc can
not be played
back
Change the disc
Change the disc
Record JPEG files using a
compliant application
JPEG files are not recorded
in a compliant formant
The built-in microcomputer Press the RESET button.
is not operating properly
due to noise
The operation keys
do not work
Front panel is not properly fixed
into its place
The antenna cable is not
connected
The radio does not
work
Insert the antenna cable firmly
The signals are too weak
Select a station manually
888-J3007-01S
25
|