Paradyne Network Router 9123 User Manual

FrameSaver® SLV  
Configuration Reference  
Document No. 9000-A2-GB31-00  
December 2002  
 
Contents  
9000-A2-GB31-00  
December 2002  
i
 
Contents  
Assigning a Synchronous Data Port to Network or DSX-1 Time Slots 3-  
n
ii  
December 2002  
9000-A2-GB31-00  
 
Contents  
iv  
December 2002  
9000-A2-GB31-00  
 
About This Guide  
Purpose and Intended Audience  
This document lists and describes the configuration options of the following  
FrameSaver SLV CSU/DSUs and routers running firmware release 2.1 or above:  
9123, 9126, 9128 standalone, 9128 carrier-mount, 9520, 9520-ILM, 9623, 9626,  
9720, 9783, 9788, 9820-2M, 9820-8M, and 9820-45M.  
Features introduced in firmware release 2.1 are described in this manual but may  
not be available in all models.  
Document Organization  
Section  
Description  
Shows how to access and save configuration  
options.  
Describes the Easy Install screens, how to set up  
RIP, and using Auto-Configuration.  
Chapter 3, Configuration Options Describes configuration options for CSU/DSUs and  
routers.  
Provides procedures for setting up internal and  
external modems, Data Backup Modules (DBMs),  
and back-to-back operation.  
Lists key terms, acronyms, concepts, and sections.  
A master glossary of terms and acronyms used in Paradyne documents is  
available on the World Wide Web at www.paradyne.com. Select Support  
Technical Manuals Technical Glossary.  
9000-A2-GB31-00  
December 2002  
v
 
           
About This Guide  
Product-Related Documents  
Complete Paradyne documentation for this product is available at  
www.paradyne.com. Select Support Technical Manuals FrameSaver Frame  
Document  
Number  
Document Title  
The FrameSaver SLV reference library contains:  
9000-A2-GB30  
9000-A2-GB31  
9000-A2-GB32  
9000-A2-GB33  
9000-A2-GB34  
FrameSaver SLV Technical Description  
Describes the features, interfaces, and cables for FrameSaver SLV  
CSU/DSUs and routers.  
FrameSaver SLV Configuration Reference  
Lists and describes the configuration options available for  
FrameSaver SLV CSU/DSUs and routers.  
FrameSaver SLV SNMP Reference  
Describes MIB details, SNMP traps, and RMON data collection  
used for FrameSaver SLV CSU/DSUs and routers.  
FrameSaver SLV Operations Guide  
Explains how to operate and troubleshoot FrameSaver SLV  
CSU/DSUs and routers.  
FrameSaver SLV Router Command Line Interface  
Describes special configuration procedures and the command line  
interface for FrameSaver SLV routers.  
Other FrameSaver model-specific documentation includes:  
9000-A2-GN19  
9000-A2-GN1D  
9123-A2-GN10  
9126-A2-GN11  
9126-A2-GN12  
9128-A2-GN10  
FrameSaver SLV ISDN Installation Instructions  
9000 Series Access Carrier Installation Instructions  
FrameSaver FLEX 9123 Installation Instructions  
FrameSaver SLV 9126 1-Slot Unit Installation Instructions  
FrameSaver SLV 9126 Router Installation Instructions  
FrameSaver SLV 9128 1-Slot Housing-to-9000 Series Access  
Carrier Upgrade Instructions  
9128-A2-GN11  
FrameSaver SLV 9128 Network Access Module (NAM) Installation  
Instructions  
9128-A2-GN12  
9520-A2-GN10  
9520-A2-GN11  
9623-A2-GN10  
9626-A2-GN10  
9783-A2-GN10  
FrameSaver SLV 9128 1-Slot Unit Installation Instruction  
FrameSaver SLV 9520 Installation Instructions  
FrameSaver SLV 9520-ILM Installation Instructions  
FrameSaver FLEX 9623 Installation Instruction  
FrameSaver SLV 9626 Installation Instructions  
Framesaver DSL 9783 CSU/DSU Installation Instructions  
vi  
December 2002  
9000-A2-GB31-00  
 
           
About This Guide  
Document  
Number  
Document Title  
9783-A2-GN11  
9788-A2-GN10  
9788-A2-GN11  
9820-A2-GN10  
FrameSaver DSL 9783 Router Installation Instructions  
Framesaver DSL 9788 CSU/DSU Installation Instructions  
Framesaver DSL 9788 Router Installation Instructions  
FrameSaver SLV, Models 9820-2M and 9820-8M, Installation  
Instructions  
9820-A2-GN11  
FrameSaver SLV, Model 9820-45M, Installation Instructions  
To order a paper copy of this or any of the above documents:  
n
n
Within the U.S.A., call 1-800-PARADYNE (1-800-727-2396)  
Outside the U.S.A., call 1-727-530-8623  
9000-A2-GB31-00  
December 2002  
vii  
 
About This Guide  
Conventions Used  
Convention Used  
When Used  
Italic  
To indicate variable information (for example, DLCI nnnn,  
where nnnn denotes a 4-digit number).  
Menu sequence:  
To provide an abbreviated method for indicating the  
selections to be made from a menu or selections from within  
a menu before performing a procedural step.  
For example,  
Main Menu Status System and Test Status indicates  
that you should select Status from the Main Menu, then  
select System and Test Status.  
(Path:)  
To provide a check point that coincides with the menu path  
shown at the top of the screen. Always shown within  
parentheses so you can verify that you are referencing the  
correct table (e.g., Path: main/config/alarm).  
Brackets [ ]  
To indicate multiple selection choices when more than one  
selection is available (e.g., Performance  
StatisticsStatus[Network/Port-1]).  
Text highlighted in blue  
To indicate a hyperlink to additional information when viewing  
this manual online. Click on the highlighted text.  
viii  
December 2002  
9000-A2-GB31-00  
 
   
Configuration Procedures  
1
This chapter includes the following:  
n
n
n
n
n
9000-A2-GB31-00  
December 2002  
1-1  
 
     
1. Configuration Procedures  
Configuration Menu  
Configuration option settings determine how the FrameSaver unit operates. Use  
the FrameSaver unit’s Configuration Edit/Display menu to display or change  
configuration option settings.  
Configuration options available depend on the model and its features. The  
Configuration Edit/Display menu shown below is for a FrameSaver SLV 9128 with  
the optional ISDN backup feature.  
Configuration Menu Example  
main/config  
9128-II  
Device Name: Node A  
11/01/2002 09:32  
CONFIGURATION EDIT/DISPLAY  
System  
Network  
DSX-1  
Data Ports  
ISDN  
Time Slot Assignment  
PVC Connections  
Management and Communication  
Auto Backup Criteria  
--------------------------------------------------------------------------------  
Ctrl-a to access these functions, ESC for previous menu  
Save  
MainMenu  
Exit  
Changing an Auto-Configuration setting can also change the FrameSaver unit’s  
Configuration, for additional information.  
1-2  
December 2002  
9000-A2-GB31-00  
 
       
1. Configuration Procedures  
Configuration Option Areas  
The FrameSaver unit arrives with configured factory default settings, which are  
located in the Factory Default Configuration option area. You can find the default  
settings for configuration options in the Configuration Option Tables in Chapter 3,  
If the factory default settings do not support your network’s configuration, you can  
customize the configuration options to better suit your application.  
Four configuration option storage areas are available.  
Configuration Option Area Description  
Current Configuration  
The currently active set of configuration options.  
Customer Configuration  
An alternate set of configuration options that you can set  
up and store for future use.  
Scratchpad Configuration  
An alternate configuration area for temporary use. The  
Scratchpad configuration is reset to the factory default  
settings when the unit is powered off and on.  
Default Factory Configuration A read-only configuration area containing the factory  
default set of configuration options.  
You can load and edit default factory configuration  
settings, but you can save changes only to the Current,  
Customer, or Scratchpad configuration option areas.  
9000-A2-GB31-00  
December 2002  
1-3  
 
     
1. Configuration Procedures  
Accessing and Displaying Configuration Options  
To access and display configuration options, load (copy) the applicable  
configuration option set into the edit area.  
Procedure  
To load a set of configuration options for editing:  
1. From the Main Menu, press the down arrow key so the cursor is on  
Configuration.  
2. Press Enter to display the Configuration menu. The Load Configuration  
From: menu appears.  
NOTE:  
Loading a configuration with many DLCIs from a unit’s Customer or  
Scratchpad configuration option area may take time. Allow a minute or  
more for the file to be loaded.  
3. Select the configuration option area from which you want to load configuration  
options and press Enter (Current Configuration, Customer Configuration,  
Scratchpad Configuration, or Default Factory Configuration).  
The selected set of configuration options is loaded into the configuration edit  
area and the Configuration Edit/Display menu appears.  
This sequence of steps would be shown as the menu selection sequence:  
Main MenuConfiguration  
1-4  
December 2002  
9000-A2-GB31-00  
 
     
1. Configuration Procedures  
Changing Configuration Options  
Procedure  
To change configuration option settings:  
1. From the Configuration Edit/Display menu, select a set of configuration  
options and press Enter.  
For example:  
ConfigurationPVC Connections  
2. Select the configuration options that are applicable to your network, and make  
appropriate changes to the setting(s). See the FrameSaver SLV Operations  
Guide for additional information.  
When creating new PVC connections or management PVCs, some  
configuration options will be blank. For a valid setting to appear, Tab to the  
configuration option and press the spacebar.  
3. Repeat Steps 1 and 2 until all changes are complete.  
NOTES:  
— Only Security Access Level 1 users can change configuration options.  
— Security Access Level 2 users can only view configuration options and run  
tests.  
— Security Access Level 3 users can only view configuration options; they  
cannot change configuration options or run tests.  
9000-A2-GB31-00  
December 2002  
1-5  
 
       
1. Configuration Procedures  
Saving Configuration Options  
When changes to the configuration options are complete, use the Save function  
key to save your changes to either the Current, Customer, or Scratchpad  
configuration areas. Note that the Scratchpad configuration is reset to the factory  
default settings when the unit is powered off and on.  
Procedure  
To save the configuration option changes:  
1. Press Ctrl-a to switch to the function key area at the bottom of the screen.  
2. Type s or S to select the Save function and press Enter.  
The Save Configuration To: screen appears.  
NOTE:  
If you try to exit the Configuration menu without saving changes, a Save  
Configuration screen appears requiring a Yes or No response.  
— If you select No, the Main Menu screen reappears and the changes  
are not saved.  
— If you select Yes, the Save Configuration To: screen appears.  
3. Select the configuration option area to which you want to save your changes  
(normally the Current Configuration) and press Enter.  
When Save is complete, Command Completeappears in the message area  
at the bottom of the screen.  
NOTE:  
There are other methods of changing configurations, like SNMP and  
Auto-Configuration. Since multiple sessions can be active at the same  
time, the last change made overwrites any previous or current changes  
being made. For instance:  
— Saving your configuration changes would cause configuration  
changes made via another method to be lost.  
— If you are making changes and someone else makes changes and  
saves them, your changes would be lost.  
1-6  
December 2002  
9000-A2-GB31-00  
 
     
2. Basic Configuration  
Using the Easy Install Feature  
The Easy Install feature provides a straightforward installation menu that requires  
minimal configuration to get the FrameSaver unit up and running quickly, and to  
set up remote configuration and management via Telnet access from the NOC  
(Network Operations Center).  
Main MenuEasy Install  
Easy Install Screen Example – T1 Interface  
main/easy_install  
9126  
Device Name: Node A  
11/01/2002 02:01  
EASY INSTALL  
Service Type:  
Frame Relay  
Node IP Address:  
Node Subnet Mask:  
000.000.000.000  
000.000.000.000  
980  
Clear  
Clear  
TS Access:  
DLCI  
Create a Dedicated Network Management Link  
Ethernet Management Options Screen  
Time Slot Assignment Screen  
Network 1 Line Framing Format:  
Network 1 Line Build Out (LBO):  
Network 1 Line Coding Format:  
DS0 Base rate (Kbps)  
ESF  
0.0  
B8ZS  
Nx64  
--------------------------------------------------------------------------------  
Ctrl-a to access these functions, ESC for previous menu  
Save  
MainMenu  
Exit  
Easy Install Screen Example – T3 Interface  
main/easy_install  
Device Name: Wasau  
EASY INSTALL  
9520-ILM  
11/01/2002 12:01  
Node IP Address:  
Node Subnet Mask:  
TS Access: None  
010.102.070.014 Clear  
255.255.255.000 Clear  
Create a Dedicated Network Management Link  
Ethernet Port Options Screen  
Network 1 Line Build Out(LBO):  
Port 1 Line Build Out(LBO):  
Short  
Short  
-------------------------------------------------------------------------------  
Ctrl-a to access these functions, ESC for previous menu  
Save  
MainMenu  
Exit  
2-2  
December 2002  
9000-A2-GB31-00  
 
   
2. Basic Configuration  
Easy Install Screen Example – DDS Interface  
main/easy_install  
Device Name: Node A  
EASY INSTALL  
9623-SLV  
11/01/2002 02:03  
Service Type:  
Frame Relay  
Node IP Address:  
Node Subnet Mask:  
TS Access: DLCI  
000.000.000.000 Clear  
000.000.000.000 Clear  
980  
Create a Dedicated Network Management Link  
Ethernet Port Options Screen  
Transmit Timing:  
Receive  
DDS Line Rate (Kbps):  
Network Initiated DCLM:  
DSU Latching Loopback (64KCC):  
Initialize From Network  
V.54 & ANSI  
Enable  
Require DSU Latching Loopback Preamble: Enable  
--------------------------------------------------------------------------------  
Ctrl-a to access these functions, ESC for previous menu  
Save  
MainMenu  
Exit  
Easy Install Screen Example – DSL Interface  
main/easy_install  
9783  
Device Name: Node A  
09/06/2002 04:02  
EASY INSTALL  
DSLAM Type:  
Paradyne  
Node IP Address:  
Node Subnet Mask:  
TS Access: VPI,VCI  
000.000.000.000  
000.000.000.000  
0 , 35  
Clear  
Clear  
Create a Dedicated Network Management Link  
Ethernet Management Options Screen  
Network 1 DSL Line Rate (Kbps)  
AutoRate  
Network 1 FRF.8 Encapsulation Mode  
Transparent  
--------------------------------------------------------------------------------  
Ctrl-a to access these functions, ESC for previous menu  
Save  
MainMenu  
Exit  
To remotely access the FrameSaver unit in Frame Relay mode, use the Dedicated  
Network Management Link that was created during installation, using the Node IP  
Address that was entered for the unit.  
See the installation instructions shipped with your unit for additional information  
and installation procedures.  
9000-A2-GB31-00  
December 2002  
2-3  
 
 
2. Basic Configuration  
The menu structure and selections, and the features and functions of the  
FrameSaver unit, are changed based upon the type of service being used.  
Table 2-1, Easy Install Configuration Options, describes the entries on the Easy  
Install screens.  
Table 2-1. Easy Install Configuration Options (1 of 7)  
Service Type  
Possible Settings: Frame Relay, Leased Line, PPP  
Default Setting: [Depends on model]  
Specifies the type of service to which the unit is to be connected.  
Frame Relay – Frame Relay-aware mode, for connection to a frame relay service. This is  
the default operational mode, and it is used to configure the FrameSaver unit in frame  
relay mode so that frame relay parameters and SLV functionality can be set up.  
If a 9123 unit is set to Leased Line, then changed to Frame Relay, Time Slot Discovery is  
temporarily suspended until LMI communication is reestablished, and all frame  
relay-related configuration options previously set up are restored, except for the Sync  
Data Port Assignments. In this case, all port assignments set to S1Port-1 are converted to  
FrameRly1 assignments on the Frame Relay Network 1 Assignment timeslot assignment  
screen.  
Leased Line – Leased-line mode, for connection to a standard leased-line service. This  
mode provides a simple and straightforward screen to guide the installer during initial  
installation, and to set up remote access to the unit.  
When operating in leased-line mode, no frame relay-related statuses, performance  
statistics, tests, configuration options, or control features are available; only physical layer  
functions are available.  
If the unit is set to Frame Relay then changed to Leased Line, all frame relay-related  
screens and features are filtered so they are transparent to the user. All frame relay links,  
DLCIs. and PVCs are preserved. For 9123 units, all Frame Relay Network 1 FrameRly1  
time slot assignments are converted to S1Port-1 on the Sync Data Port Assignments  
screen.  
PPP – Point-to-Point Protocol mode. A single PPP circuit exists between Port1 and Net1.  
Changing to or from PPP mode causes a reset.  
2-4  
December 2002  
9000-A2-GB31-00  
 
           
2. Basic Configuration  
Table 2-1. Easy Install Configuration Options (2 of 7)  
DSLAM Type (9783)  
Possible Settings: Paradyne, Alcatel (NewBridge), PairGain, Nokia  
Default Setting: Paradyne  
Ensures interoperability with non-Paradyne DSLAMs, not just the Hotwire GranDSLAM.  
This option is only available from the Easy Install screen.  
NOTES:  
– The default is set before the unit is shipped, based upon the CLEC customer  
ordering the unit. If you change the default, you must Save the change for it to take  
effect, which will reset the unit.  
– When the default is changed, the default settings for other configuration options  
change.  
Paradyne – The FrameSaver device is used with a Hotwire GranDSLAM.  
Alcatel (NewBridge) – The FrameSaver device is used with Alcatel’s NewBridge  
DSLAM.  
PairGain – The FrameSaver device is used with PairGain’s DSLAM.  
Nokia – The FrameSaver device is used with Nokia’s DSLAM.  
Node IP Address  
Possible Settings: 001.000.000.000–126.255.255.255,  
128.000.000.000–223.255.255.255, Clear  
Default Setting: Clear (000.000.000.000)  
Specifies the IP address needed to access the node. Since an IP address is not bound to  
a particular port, it can be used for remote access via a management PVC.  
001.000.000.000 – 223.255.255.255 – Shows the IP address for the node, which can be  
viewed or edited. The first octet of the address cannot be decimal 0 or 127, or greater than  
223.  
Clear – Fills the node IP address with zeros.  
Node Subnet Mask  
Possible Settings: 000.000.000.000 – 255.255.255.255, Clear  
Default Setting: 000.000.000.000  
Specifies the IP address subnet mask that is needed to access the node. Since the  
subnet mask is not bound to a particular port, it can be used with the Node IP address for  
remote access via a management PVC.  
000.000.000.000 – 255.255.255.255 – Shows the subnet mask for the node, which can be  
viewed or edited.  
Clear – Fills the node subnet mask with zeros. When the node’s subnet mask is all zeros,  
the IP protocol creates a default subnet mask based upon the IP address class  
(Class A: 255.000.000.000, Class B: 255.255.000.000, or Class C: 255.255.255.000).  
9000-A2-GB31-00  
December 2002  
2-5  
 
           
2. Basic Configuration  
Table 2-1. Easy Install Configuration Options (3 of 7)  
TS Access  
Possible Settings: None, DLCI, VPI,VCI, DLCI_on_VPI,VCI  
Default Setting: [Depends on model]  
Specifies the type of Virtual Circuit (VC) by which special troubleshooting (TS) access is  
provided to service providers.  
Display Conditions – This setting does not appear if Service Type is PPP.  
None – No special troubleshooting link is defined.  
DLCI – (Models whose network interface does not support ATM.) Allows the user to select  
a frame relay DLCI to be designated for special troubleshooting access.  
VPI,VCI – (Models whose network interface supports ATM.) Specifies an ATM VC on a  
specific ATM VPI,VCI for TS access. It specifies the VPI and VCI on the network interface  
for service provider troubleshooting. ATM data is presumed to be encapsulated according  
to RFC 1483. VPI 0,VCI 35 is the default management path between the  
FrameSaver device and the DSLAM. The VPI and VCI are entered separately.  
– VPI range is 0–15.  
– VCI range is 32–255.  
DLCI_on_VPI,VCI – (Models whose network interface supports ATM.) Specifies a frame  
relay DLCI VC on a specific ATM VPI,VCI for TS access. DLCI range is 16–1007. ATM  
data is presumed to be encapsulated according to RFC 1490.  
Create a Dedicated Network Management Link  
Possible Settings: 16 1007  
Default Setting: Initially blank  
Enter a DLCI number and (for units that support ATM) VPI,VCI for a dedicated network  
management PVC.  
NOTE: With the cursor on the Create a Dedicated Network Management Link field,  
press Enter. The Which DLCI would you like to Create a Dedicated  
Frame Relay Management PVC on?prompt appears. If the DLCI entered is over  
an ATM link, prompts for VPI and VCI also appear.  
Display Conditions – This setting does not appear if Service Type is PPP.  
16 1007 – Specifies the DLCI number be used.  
Ethernet Management Options Screen  
For units with an Ethernet port, provides a link to the Ethernet Management Options  
Screen. Press Enter and the screen appears. After configuring Ethernet options, press the  
Esc key to return to the Easy Install screen.  
Time Slot Assignment Screen (9123, 9126, 9128)  
For units with a T1 network interface, provides a link to the timeslot assignment screen  
appropriate to the Service Type. Press Enter and:  
If Service Type is Frame Relay, the Network 1 Frame Relay Assignments screen  
appears.  
If Service type is Leased Line, the Sync Data Port Assignments screen appears.  
After configuring timeslots, press the Esc key to return to the Easy Install screen.  
2-6  
December 2002  
9000-A2-GB31-00  
 
               
2. Basic Configuration  
Table 2-1. Easy Install Configuration Options (4 of 7)  
Network 1 Line Framing Format (9123, 9126, 9128)  
Possible Settings: D4, ESF  
Default Setting: ESF  
For units with a T1 network interface, specifies the framing format for transmitted and  
received signals on the T1 network interface.  
D4 – Uses D4 framing format.  
NOTE: This setting is not recommended by network carriers. False yellow alarms may  
occur after traffic has been running and the channel returns to idle, or when there is  
light traffic when other settings are selected. ESF format does not create this problem.  
ESF – Uses Extended Superframe framing format.  
Network 1 Line Coding Format (9123, 9126, 9128)  
Possible Settings: AMI, B8ZS  
Default Setting: B8ZS  
For units with a T1 network interface, specifies the line coding format for the network  
interface.  
AMI – Uses Alternate Mark Inversion (AMI) line coding format.  
B8ZS – Uses Bipolar 8 Zero Substitution (B8ZS) line coding format.  
Network 1 Line Build Out (9123, 9126, 9128)  
Possible Settings: 0.0, –7.5, –15, –22.5  
Default Setting: 0.0  
For units with a T1 network interface, specifies the line build out for the signal transmitted  
to the network.  
0.0, –7.5, –15, –22.5 – Specifies line build out in dB.  
Network 1 Line Build Out (9520, 9520-ILM)  
Possible Settings: Short, Long  
Default Setting: Short  
For units with a T3 network interface, specifies whether a line equalization filter is  
activated to simulate a longer cable.  
Short – The equalization filter is activated. Use this option for network cables less than  
100 feet long.  
Long – The equalization filter is not activated. Use this option for network cables 100 feet  
or longer.  
Port 1 Line Build Out (9520-ILM)  
Possible Settings: Short, Long  
Default Setting: Short  
For units with a T3 data port interface, specifies whether a line equalization filter is  
activated to simulate a longer cable.  
Short – The equalization filter is activated. Use this option for DTE cables less than 100  
feet long.  
Long – The equalization filter is not activated. Use this option for DTE cables 100 feet or  
longer.  
9000-A2-GB31-00  
December 2002  
2-7  
 
     
2. Basic Configuration  
Table 2-1. Easy Install Configuration Options (5 of 7)  
DS0 Base Rate (9123, 9126, 9128)  
Possible Settings: Nx64, Nx56  
Default Setting: Nx64  
Selects the base rate for the DS0s allocated to frame relay on the network interface.  
Nx64 – The base rate is 64 Kbps.  
Nx56 – The base rate is 56 Kbps.  
Network 1 Port Type (9820-2M, 9820-8M)  
Possible Settings: E530, V.35, X.21  
Default Setting: V.35  
Selects the type of port to be used for the network data port.  
E530 – The port is configured as an EIA-530-A-compatible DTE. An EIA-530 compatible  
DCE can be directly connected to the DB25 connector for this port on the rear of the  
FrameSaver unit.  
V.35 – The port is configured as a V.35-compatible DTE. A V.35-compatible DCE can be  
connected to the DB25 connector for this port using an adapter cable on the rear of the  
FrameSaver unit.  
X.21 – The port is configured as a V.11/X.21-compatible DTE. A V.11/X.21-compatible  
DCE can be connected to the DB25 connector for this port using an adapter cable on the  
rear of the FrameSaver unit.  
Network 1 DSL Line Rate Mode (9720, 9783, 9788)  
Possible Settings: Hunt (9783), AutoRate, Fixed  
Default Setting: AutoRate  
Specifies the mode to be used for rate selection.  
Hunt – (9783 only.) The unit attempts to train at rate specified by Network 1 DSL Line  
Rate. If that fails, the unit attempts to train at the next higher rate, and, if unsuccessful,  
cycles through all the rates until training is successful or the unit is reset.  
AutoRate – The unit automatically detects the line rate from the network interface.  
Fixed – The unit uses the line rate specified by Network 1 DSL Line Rate.  
2-8  
December 2002  
9000-A2-GB31-00  
 
   
2. Basic Configuration  
Table 2-1. Easy Install Configuration Options (6 of 7)  
Network 1 DSL Line Rate (9783)  
Possible Settings:  
If DSLAM Type is set to Paradyne, or if DSLAM Type is set to Nokia and Network 1  
DSL Line Rate Mode is set to Fixed: 144, 192, 208, 256, 272, 384, 400, 512, 528,  
768, 784, 1024, 1152, 1168, 1536, 1552, 2320  
If DSLAM Type is set to Alcatel (NewBridge): 208, 400, 784, 1168, 1552, 2320  
– If DSLAM Type is set to Nokia and Network 1 DSL Line Rate Mode is set to Hunt:  
192, 384, 768, 1152, 1536  
If DSLAM Type is set to PairGain: 144, 192, 208, 256, 272, 384, 400, 512, 528,  
768, 784, 1024, 1152, 1168, 1536, 1552, 2320  
Default Setting:  
– If DSLAM Type is set to Alcatel (NewBridge) and Network 1 DSL Line Rate Mode is  
set to Hunt: 208  
– If DSLAM Type is set to Nokia and Network 1 DSL Line Rate Mode is set to Hunt:  
384  
If DSLAM Type is set to PairGain and Network 1 DSL Line Rate Mode set to Fixed:  
784  
(If DSLAM Type is set to Paradyne, Network 1 DSL Line Rate Mode is set to  
AutoRate and Network 1 DSL Line Rate does not appear)  
Determines whether the rate on the DSL interface is set to a specific value or  
automatically detected using the Conexant AutoBaud algorithm.  
144 – 2320 – Sets the DSL line rate in kbps.  
Network 1 DSL Line Rate (9788)  
Possible Settings:  
If PSD Mask is Symmetric: 200, 264, 328, 392, 456, 520, 584, 648, 712, 776, 784,  
840, 904, 968, 1032, 1096, 1160, 1224, 1288, 1352, 1416, 1480, 1544, 1552, 1608,  
1672, 1736, 1800, 1864, 1928, 1992, 2056, 2120, 2184, 2248, 2312  
If PSD Mask is Asymmetric and Region Setting is Annex A: 776, 784, 1544, 1552  
If PSD Mask is Asymmetric and Region Setting is Annex B: 2056, 2312  
Default Setting: [None]  
Determines the rate on the DSL network interface. Valid rates, and the rates presented on  
the screen, depend on the values of Region Setting and PSD Mask on the Network  
Physical Interface Options screen. If a change to another configuration option renders the  
selected DSL Line Rate invalid, the line rate is set to AutoRate.  
Display Conditions – Network 1 DSL Line Rate does not appear if Network 1 DSL Line  
Rate Mode is set to AutoRate.  
200 – 2312 – The DSL line rate is set to the specified rate in kbps.  
Network 1 Operating Rate (9720)  
Possible Settings: AutoRate, 64, 128, 144  
Default Setting: AutoRate  
Determines the rate on the IDSL network interface.  
AutoRate – The unit automatically detects the line rate from the network interface.  
64, 128, 144 – The IDSL line rate is set to the specified rate in kbps.  
9000-A2-GB31-00  
December 2002  
2-9  
 
             
2. Basic Configuration  
Table 2-1. Easy Install Configuration Options (7 of 7)  
Network 1 Channel (9720)  
Possible Settings: B1, B2  
Default Setting: B1  
Specifies the B channel used for data transfer when the line rate is 64 kbps.  
Display Conditions – Network 1 Channel appears only when Network 1 Operating Rate  
is set to 64.  
B1 – The B1 channel is used for data transfer.  
B2 – The B2 channel is used for data transfer.  
Port-1 Port Type (9520, 9788, 9820-2M, 9820-8M)  
Possible Settings: E530, V.35, X.21, HSSI  
Default Setting:  
9520: HSSI  
9788, 9820-2M, 9820-8M: V.35  
Specifies the port type of the data port.  
E530 – The port is configured as an EIA-530-A-compatible DCE. An EIA-530-A-  
compatible DTE may be directly connected to the DB25 connector for the port.  
V.35 – The port is configured as a V.35-compatible DCE. A V.35-compatible DTE may be  
connected to the port using a DB25-to-MS34 adapter.  
X.21 – The port is configured as an X.21-compatible DCE. An X.21-compatible DTE may  
be connected to the port using a DB25-to-DB15 adapter.  
HSSI – The port is configured as a HSSI-compatible DCE. A HSSI-compatible DTE may  
be directly connected to the DB25 connector for the port.  
Port 1 Port Rate (9520)  
Possible Settings (HSSI): 7456, 11184, 17250, 25875, 44736, 51750  
Default Setting (HSSI): 51750  
Possible Settings (V.35): 512, 1025, 1537, 2050, 2562, 3074, 3587, 4099, 4611, 5124,  
5636, 6149, 6661, 7073, 7685, 8197  
Default Setting (V.35): 6149  
Selects the clock rate in Kbps for the user data port.  
Network 1 FRF.8 Encapsulation Mode (9783 and 9788)  
Possible Settings: Translational, Transparent  
Default Setting: Transparent  
Specifies the type of FRF.8 upper-layer protocol encapsulation used on the link for each  
pair of interoperable Frame Relay and ATM PVCs.  
Translational – Encapsulated data is translated (RFC 1490 to RFC 1483). FrameSaver  
multiplexing and SLV communications are not supported in this mode.  
Transparent – Encapsulated data is forwarded without being translated.  
2-10  
December 2002  
9000-A2-GB31-00  
 
                 
2. Basic Configuration  
Using RIP with FrameSaver SLV CSU/DSUs  
Using the system’s standard Routing Information Protocol (RIP) feature, routing  
information is passed to the router over the management PVC, so the router can  
learn routes to FrameSaver devices. Node IP information should be set up (see  
Procedure  
To set up your router and FrameSaver SLV CSU/DSU so that the router can learn  
routes to FrameSaver devices:  
1. Configure the router to receive RIP.  
For example, if using a Cisco router, you would use the commands  
config-t, router RIP, int serialx, IP RIP Receive version 1,  
then ctl-z WR.  
2. Create a Standard DLCI for the user data port.  
ConfigurationData PortsDLCI Records  
3. Create a Management PVC using the user data port DLCI just configured.  
ConfigurationManagement and CommunicationManagement PVCs  
4. Set Primary Link RIP to Standard_Out, and Save the configuration.  
Options, in Chapter 3, Configuration Options, for configuration information.  
9000-A2-GB31-00  
December 2002  
2-11  
 
     
2. Basic Configuration  
Entering System Information and Setting the System Clock  
Select System Information to set up or display the general SNMP name for the  
unit, its location, and a contact for the unit, as well as to set the system clock.  
Main MenuControlSystem Information  
The following information is available for viewing. Save any entries or changes.  
If the selection is . . . Enter the . . .  
Device Name  
Unique name for device identification of up to 20 characters.  
SNMP system name; can be up to 255 characters.  
System Name  
System Location  
System Contact  
System’s physical location; can be up to 255 characters.  
Name and how to contact the system person; can be up to  
255 characters.  
Date  
Time  
Current date in the month/day/year format (mm/dd/yyyy).  
Current time in the hours:minutes format (hh:mm).  
NOTE:  
To clear existing information, place the cursor in the Clear field (Tab to the  
Clear field) and press Enter.  
See the FrameSaver SLV Operations Guide to set up and administer logins.  
2-12  
December 2002  
9000-A2-GB31-00  
 
               
2. Basic Configuration  
Setting Up Auto-Configuration  
The auto-configuration feature is available in frame relay mode on all models  
except those with DSL interfaces. It allows you to select a method of automatic  
configuration and connection of DLCIs within the FrameSaver unit, as well as to  
automatically remove DLCIs and connections that are no longer supported by the  
network service provider.  
Main MenuAuto-Configuration  
Auto-Configuration Screen Example  
main/auto-configuration  
Device Name: Node A  
9128-II  
8/18/2000 23:32  
AUTO-CONFIGURATION  
Frame Relay Discovery Mode:  
1MPort  
Enable  
Automatic Circuit Removal:  
Automatic Backup Configuration:  
Single_Site_Backup  
--------------------------------------------------------------------------------  
Ctrl-a to access these functions, ESC for previous menu  
Save  
MainMenu  
Exit  
This feature also maintains associated DLCI option settings when Standard LMI is  
used on the network interface.  
If an ISDN DBM is not installed, Automatic Backup Configuration does not appear  
Configuration) for additional information).  
9000-A2-GB31-00  
December 2002  
2-13  
 
       
2. Basic Configuration  
Selecting a Frame Relay Discovery Mode  
When a Frame Relay Discovery Mode is active, the FrameSaver unit “discovers”  
network DLCIs from the network LMI status response message. It configures a  
network DLCI and a user data port DLCI, and automatically connects them to  
create a PVC.  
Main MenuAuto-ConfigurationFrame Relay Discovery Mode  
Automatically configured network DLCIs are multiplexed, and each automatically  
configured port DLCI carries the same DLCI Number as its corresponding network  
DLCI. These are the same DLCI numbers that would have been available had the  
FrameSaver unit not been inserted in the link, between your equipment and the  
network.  
NOTE:  
A local Management PVC (e.g., the PVC between the router and the  
FrameSaver unit’s user data port) must be configured manually.  
The following will occur when a Frame Relay Discovery Mode is selected:  
Discovery Mode  
Configuration Description  
1MPort  
Auto-configuration is enabled on Port-1.  
A management DLCI is configured.  
A multiplexed network DLCI containing two embedded  
DLCIs (EDLCIs) is configured for Port-1 user data and  
management data.  
A PVC connection is configured between the network  
and port DLCIs.  
1Port  
Auto-configuration is enabled on Port-1.  
No management DLCI is configured.  
A multiplexed network DLCI is configured for Port-1 user  
data.  
A PVC connection is configured between the network  
and port DLCIs.  
1PPort  
Auto-Configuration is enabled on Port-1.  
A Port-1 DLCI is created for each network DLCI and  
automatically cross-connected to it.  
Payload management is configured for the network  
DLCI and assigned the Node IP Address.  
2MPorts  
Auto-configuration is enabled on both Port-1 and Port-2.  
(only applies to models with  
multiple data ports)  
A multiplexed network DLCI containing three EDLCIs is  
configured for Port-1 customer data, Port-2 customer  
data, and management data.  
PVC connections are configured between the network  
and port DLCIs.  
A management PVC is configured on the network  
interface.  
2-14  
December 2002  
9000-A2-GB31-00  
 
             
2. Basic Configuration  
Discovery Mode  
Configuration Description  
NetOnly  
Auto-configuration of a network DLCI only; no Port-1 or  
PVC connections are configured.  
No Port-1, PVC connection, or management DLCI is  
configured.  
Disable  
No frame relay discovery or automatic configuration  
takes place.  
The FrameSaver unit will be configured manually.  
NOTE:  
If the default setting (1MPort or 1PPort) is not the setting required for your  
application, change the Frame Relay Discovery Mode before connecting the  
network cable or editing discovered option settings. Otherwise, the  
FrameSaver unit will start discovering DLCIs as soon as it powers up.  
If this occurs, you can recover by deleting the discovered DLCIs. If only a local  
management PVC between the router and the FrameSaver unit has been  
configured, simply select the desired Frame Relay Discovery Mode and Save  
the change.  
The default discovery mode, depending on model, is 1MPort or 1PPort.  
When 1MPort mode is active, the unit creates for each DLCI discovered on the  
network a multiplexed network interface DLCI (which contains two EDLCIs: one for  
Port-1 data and the other for management), a standard Port-1 DLCI (with the  
same number as the network interface DLCI), and a Management PVC, then  
cross-connects them. When LMI is active on the network interface and PVC status  
information (with provisioned DLCI numbers) is next received from the network,  
the unit automatically saves the settings to the Current Configuration area.  
When 1PPort mode is active, the unit uses the Network DLCI values obtained from  
the Network LMI status response message to automatically configure for each  
DLCI a corresponding DLCI for Port 1 having the same numeric value as the  
Network DLCI, and automatically cross connects them. The DLCIs created on the  
network side are IP Enabled (not standard or multiplexed) DLCIs. In addition,  
payload management is configured for the network DLCI and assigned the Node  
IP Address.  
Configuration options set by selecting a discovery mode can be manually  
modified, refined, or deleted at any time using the Configuration menus. No  
previously discovered and configured DLCIs or cross-connections will be removed  
unless authorized or Automatic Circuit Removal is enabled (see Automatically  
Removing a Circuit on page 2-16). Additional discovered DLCIs will be configured  
according to the current Frame Relay Discovery Mode setting. Selecting or  
changing the setting will not affect IP Addresses or Subnet Masks.  
NOTE:  
When auto-configuration creates a multiplexed DLCI, but a standard DLCI is  
needed, change the DLCI to standard from the network DLCI Records screen:  
ConfigurationNetworkDLCI Records  
9000-A2-GB31-00  
December 2002  
2-15  
 
 
2. Basic Configuration  
When a Frame Relay Discovery Mode is changed and saved, the Saving will  
cause Auto-Configuration to update and Restart. Are you sure?  
prompt appears. No is the default for this prompt.  
n
If Yes (y) is entered, the Delete All DLCIs and PVC Connections?  
prompt appears. No is the default for this prompt.  
— If Yes is entered, all multiplexed DLCIs and PVC Connections are deleted,  
except for Management PVCs with the user data port as the primary  
destination and the Management PVC that is designated as TS  
Management Link.  
— If No is entered, previously discovered and auto-configured option settings  
will not be removed, but configuration updates due to LMI response  
messages are performed according to the just saved mode setting.  
n
If No (n) is entered, or if you exit the screen without responding to the prompt,  
no Auto-Configuration updates are performed and updates due to LMI  
response messages are performed according to the previously saved setting.  
Automatically Removing a Circuit  
Using the automatic circuit removal feature, which comes enabled, network DLCIs  
and PVCs can be automatically removed from the unit’s configuration when the  
network service provider no longer supports them. Automatic deletion is based  
upon information from a LMI full status response on an active frame relay link.  
When this feature is set to:  
n
Enable – The following will be automatically removed from the unit’s  
configuration:  
— Unsupported network DLCIs and PVC connections that include  
multiplexed network DLCIs.  
— Standard network DLCIs that are Payload Managed or IP Enabled.  
— Unsupported standard network DLCIs that are not configured as the  
primary destination in a management PVC.  
— Non-management PVCs in which unsupported standard network DLCIs  
are included.  
— DLCIs not included in three consecutive LMI full status response  
messages.  
— LMI status responses that indicate a Deleted status for the DLCI.  
All configured options relating to the deleted circuits are also deleted and they  
revert to their default settings.  
A DLCI will not be deleted if the physical interface or frame relay link is down,  
or if the DLCI is used for the TS Management Link.  
n
Disable – Unused network DLCIs, PVC connections, and management PVCs  
must be manually removed.  
If the model has ISDN backup capability, ISDN Link Profiles associated with  
the deleted records and alternate destinations will be deleted, as well.  
2-16  
December 2002  
9000-A2-GB31-00  
 
     
3. Configuration Options  
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
Table 3-8, T3 Network Physical Interface Options  
Table 3-9, DDS Network Physical Interface Options  
Table 3-10, IDSL Network Physical Interface Options  
Table 3-12, SHDSL Network Physical Interface Options  
Table 3-13, Synchronous Network Data Port Physical Interface Options  
Table 3-18, T3 User Port Physical Interface Options  
Table 3-28, Network ATM Options  
Table 3-30, IP Path List  
Table 3-32, Management PVC Options  
3-2  
December 2002  
9000-A2-GB31-00  
 
3. Configuration Options  
Configuring the Overall System  
The System menu options are explained in the following sections:  
n
n
n
n
n
Configuring Frame Relay and LMI for the System (CSU/DSUs)  
Select Frame Relay and LMI from the System menu to display or change the  
Frame Relay and LMI options for the entire system (see Table 3-1, System Frame  
Relay and LMI Options). The option appears only when Service Type is Frame  
Relay.  
Main MenuConfigurationSystem Frame Relay and LMI  
See Configuring PPP for an Interface on page 3-63 to set an interface’s frame  
relay options.  
Table 3-1. System Frame Relay and LMI Options (1 of 4)  
LMI Behavior  
Possible Settings: Independent,  
Net1-FR1_Follows_Port-1,  
Net1-FR1_Follows_Port-2,  
Net1-FR1_Follows_Rtr-S0,  
Port-1_Follows_Net1-FR1,  
Port-2_Follows_Net1-FR1,  
Rtr-S0_Follows_Net1-FR1,  
All_Ports_Follow_Net1-FR1,  
Port-1_Codependent_with_Net1-FR1,  
Port-2_Codependent_with_Net1-FR1,  
Rtr-S0_Codependent_with_Net1-FR1,  
Default Setting: Independent  
Configures the device to allow the state of the LMI to be passed from one interface to  
another, determining how the unit will handle a change in the LMI state. Sometimes  
referred to as LMI pass-through.  
Display Conditions – Port-n options are available on CSU/DSUs and Rtr-S0 options  
are available on FrameSaver SLV Routers. Port-2 options are available on units with  
two data ports.  
NOTE: LMI Behavior cannot be changed while Auto Backup is enabled. A warning  
message appears at the bottom of the screen if auto backup is enabled. First, disable  
Auto Backup, and then change LMI Behavior.  
Independent – Handles the LMI state of each interface separately so that the LMI state of  
one interface has no effect on the LMI state of another interface. Provides LMI Spoofing.  
This is the recommended setting when backup is configured, and for Network Service  
Providers (NSPs).  
9000-A2-GB31-00  
December 2002  
3-3  
 
                       
3. Configuration Options  
Table 3-1. System Frame Relay and LMI Options (2 of 4)  
LMI Behavior (continued)  
Net1-FR1_Follows_Port-1 – Brings LMI down on the network interface when LMI on  
Port-1 goes down, disabling the network interface and deasserting its control leads. When  
LMI on Port-1 comes back up, the network interface is reenabled. The LMI state on the  
network interface has no effect on the LMI state on Port-1. That is, the network interface’s  
LMI follows Port-1’s LMI. Used at central sites, this setting is useful when the remote site  
router on the other end of the PVC connection can initiate recovery via a redundant  
central site when there is a catastrophic central site LAN or router failure. Not  
recommended for NSPs.  
Net1-FR1_Follows_Port-2 – Reacts like the Net1-FR1_Follows_Port-1 selection, but for  
Port-2 instead.  
Rtr-S0_Follows_Port-1 – Brings LMI down on the network interface when LMI on Rtr-S0  
goes down, disabling the network interface and deasserting its control leads. When LMI  
on Rtr-S0 comes back up, the network interface is reenabled. The LMI state on the  
network interface has no effect on the LMI state on Rtr-S0. That is, the network interface’s  
LMI follows Rtr-S0’s LMI.  
Port-1_Follows_Net1-FR1 – Brings LMI down on Port-1 when LMI on the network  
interface goes down, disabling Port 1 and deasserting its control leads. When LMI on the  
network interface comes back up, Port-1 is reenabled and its control leads are reasserted.  
The LMI state on Port-1 has no effect on the LMI state on the network interface. That is,  
Port-1’s LMI follows the network interface’s LMI. This setting is useful if the router  
connected to Port-1 is used to initiate recovery when network failures are detected.  
Port-2_Follows_Net1-FR1 – Reacts like the Port-1_Follows_Net1-FR1 selection, but for  
Port-2 instead.  
Rtr-S0_Follows_Net1-FR1 – Brings LMI down on Rtr-S0 when LMI on the network  
interface goes down, disabling Rtr-S0. When LMI on the network interface comes back  
up, Rtr-S0 is reenabled. The LMI state on Rtr-S0 has no effect on the LMI state on the  
network interface. That is, Rtr-S0’s LMI follows the network interface’s LMI.  
All_Ports_Follow_Net1-FR1 – Brings LMI down on all user data ports when LMI on the  
network interface goes down, disabling all ports and deasserting their control leads.  
Allows LMI to come back up and reenables the ports when LMI comes up on the network.  
That is, LMI on each port follows the network interface’s LMI. The state of LMI on the port  
will not affect the state of LMI on the network interface.  
Port-1_Codependent_with_Net1-FR1 – Brings LMI down on the network interface when  
LMI on Port-1 goes down (or LMI down on Port-1 when LMI on the network interface goes  
down), and allows LMI to come back up when LMI comes back on the other interface.  
That is, the LMI state for one interface is dependent on the other. Use this setting when  
backup is through the router instead of the unit. It is not recommended since it makes fault  
isolation more difficult.  
Port-2_Codependent_with_Net1-FR1 – Reacts like the  
Port-1_Codependent_with_Net1-FR1 selection, but for Port-2 instead. The state of LMI  
on the network interface will not affect the state of LMI on Port-1.  
Rtr-S0_Codependent_with_Net1-FR1 – Brings LMI down on the network interface when  
LMI on Rtr-S0 goes down (or LMI down on Rtr-S0 when LMI on the network interface  
goes down), and allows LMI to come back up when LMI comes back on the other  
interface. That is, the LMI state for one interface is dependent on the other.  
3-4  
December 2002  
9000-A2-GB31-00  
 
 
3. Configuration Options  
Table 3-1. System Frame Relay and LMI Options (3 of 4)  
LMI Behavior (9783 and 9788)  
Possible Settings: Independent, Net1-FR1_Follows_Port-1,  
Port-1_Follows_Net1-FR1, Port-1_Codependent_with_Net1-FR1  
Default Setting: Port-1_Codependent_with_Net1-FR1  
For units that support ATM, configures the state of LMI on Port-1 and the state of the ATM  
link on the network interface to be passed from one interface to another.  
Independent – Handles the state of each interface separately so that the LMI state of  
Port-1 has no effect on the state of the ATM link on the network interface, and vice versa.  
Net1-FR1_Follows_Port-1 – Brings down VCs cross-connected to Port-1 on the network  
interface when LMI on Port-1 goes down, and sends F5 OAM cells on all network VCs  
cross-connected to Port-1 DLCIs to alert the network and far-end device that frame relay  
data can not be delivered through the device. When LMI on Port-1 comes back up, the  
network VCs are also re-enabled. This setting is useful at a central site when the remote  
site router on the other end of the PVC connection can initiate recovery via a redundant  
central site when there is a catastrophic central site LAN or router failure. Not  
recommended for NSPs.  
Port-1_Follows_Net1-FR1 – Brings down LMI on Port-1 when there is a physical failure  
or ATM failure on the network interface. When the alarm on the network interface is  
cleared, Port-1 is re-enabled and its control leads are reasserted. This setting is useful if  
the router connected to Port-1 is used to initiate recovery when network failures are  
detected.  
Port-1_Codependent_with_Net1-FR1 – The LMI state for Port 1 and the Net1-FR1  
interface are dependent on each other. If the LMI is down on either interface, the system  
will bring the LMI down on the other interface. When the LMI is up on either interface, the  
system will bring the LMI up on the other interface. When Port-1 LMI goes down, in  
addition to bringing down the internal network frame relay link, the unit also sends  
F5 OAM cells on all network VCs cross-connected to Port-1 DLCIs to alert the network  
and far-end device that frame relay data can not be delivered through the device. Use this  
setting when backup is through the router instead of the unit. Note that when the router is  
disconnected, the NSP cannot access the unit using multiplexed VCs.  
LMI Error Event (N2)  
Possible Settings: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10  
Default Setting: 3  
Configures the LMI-defined N2 parameter, which sets the number of errors that can occur  
on the LMI link before an error is reported. Applies to both the user and network sides of a  
UNI.  
1 – 10 – Specifies the maximum number of errors.  
LMI Clearing Event (N3)  
Possible Settings: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10  
Default Setting: 1  
Configures the LMI-defined N3 parameter, which sets the number of error-free messages  
that must be received before clearing an error event. Applies to both the user and network  
sides of a UNI.  
1 – 10 – Specifies how many error-free messages it will take to clear the error event.  
9000-A2-GB31-00  
December 2002  
3-5  
 
               
3. Configuration Options  
Table 3-1. System Frame Relay and LMI Options (4 of 4)  
LMI Status Enquiry (N1)  
Possible Settings: 1, 2, 3, 4, . . . 255  
Default Setting: 6  
Configures the LMI-defined N1 parameter, which sets the number of status enquiry polling  
cycles that the user side of the LMI initiates before a full status enquiry is initiated. Applies  
to the user side of a UNI only.  
1 – 255 – Specifies the number of status enquiry polling cycles that can be initiated before  
a full status enquiry is initiated.  
LMI Heartbeat (T1)  
Possible Settings: 5, 10, 15, 20, 25, 30  
Default Setting: 10  
Configures the LMI-defined T1 parameter, which sets the number of seconds between the  
initiation of status enquiry messages on the user side of the LMI. Applies to the user side  
of a UNI only.  
5 – 30 – Specifies the number of seconds between the initiation of status enquiry  
messages in increments of 5.  
LMI Inbound Heartbeat (T2)  
Possible Settings: 5, 10, 15, 20, 25, 30  
Default Setting: 15  
Configures the LMI-defined T2 parameter, which sets the number of seconds between the  
receipt of status enquiry messages on the network side of the LMI. Applies to the network  
side of a UNI only.  
5 – 30 – Specifies the number of seconds between the receipt of status enquiry messages  
in increments of 5.  
LMI N4 Measurement Period (T3)  
Possible Settings: 5, 10, 15, 20, 25, 30  
Default Setting: 20  
Configures the LMI-defined T3 parameter, which is the time interval (in seconds) that the  
network side of the LMI uses to measure the maximum number of status enquiry  
messages that have been received (N4) from the user side.  
5 – 30 – Specifies the interval of time in increments of 5.  
3-6  
December 2002  
9000-A2-GB31-00  
 
                   
3. Configuration Options  
Configuring PPP Options  
PPP options are selected from the System menu (see Table 3-2, PPP Options).  
The option appears only when Service Type is PPP.  
Main MenuConfigurationSystemPPP  
Table 3-2. PPP Options  
PPP  
Possible Settings: Independent, Port-1_Follows_Net  
Default Setting: Independent  
Allows you to pass the state of PPP from one interface to the other.  
Independent – The state of PPP on one interface does not affect the state of the other.  
Port-1_Follows_Net – The state of PPP on Port 1 depends on the state of PPP on the  
Network 1 interface. If PPP is down on Network 1, the system brings down PPP on the  
Port 1 interface and disables the port, causing the DSR, CD, and CSR control leads to be  
deasserted. If PPP is up on Network 1, the system enables Port 1 and asserts the control  
leads.  
9000-A2-GB31-00  
December 2002  
3-7  
 
         
3. Configuration Options  
Configuring Class of Service Definitions  
Select Class of Service Definitions from the System menu to display or change the  
Class of Service definitions to be used with latency, availability, and throughput  
measurements of IP traffic on IP Enabled circuits.  
Main MenuConfigurationSystem Class of Service Definitions  
The Class of Service Definitions screen appears.  
Procedure  
To create a new Class of Service definition:  
1. To manually assign definition names and code points, proceed to Step 4  
2. To automatically create Class of Service names and associate them with code  
points according to RFCs 2474, 2497, and 2498, select RfcCodePoints. The  
following settings are established:  
Field  
Setting After RfcCodePoints Selected  
Class of Service Name  
1 – NewCtrl  
2 – Expd Fwd  
3 – AFClass4  
4 – AFClass3  
5 – AFClass2  
6 – AFClass1  
7 – Default  
Measure Latency & Availability  
1 – N  
2 – Y  
3 – Y  
4 – Y  
5 – Y  
6 – Y  
7 – Y  
Code Points  
1 (NetwCtrl) – 110000, 111000  
2 (Expd Fwd) – 101110  
3 (AFClass4) – 100010, 100100, 100110  
4 (AFClass3) – 011010, 011100, 011110  
5 (AFClass2) – 010010, 010100, 010110  
6 (AFClass1) – 001010, 001100, 001110  
7 (Default)  
– 000000  
3. If these settings are satisfactory, proceed to Step 10.  
4. Type a name of up to 8 characters into one of the Name fields next to IDs 1–6.  
5. To unassign all code points by inserting blank names, select ClrAllCodePoints.  
To assign all Code Points to a Class of Service name of Default, select  
DefaultCodePoints.  
6. Select PgDn or PgUp. The Code Point Assignment screen appears.  
7. For any Code Point you want to assign to the name, type the name you  
selected in Step 4 into the Name field to the right of the Code Point.  
3-8  
December 2002  
9000-A2-GB31-00  
 
       
3. Configuration Options  
8. Select Save, then select PgDn or PgUp. The Class of Service Definitions page  
reappears. In the Code Points Assigned column next to your selected name  
there is now a Y for Yes.  
9. If latency and availability should be measured for the selected name, change  
the N in the Measure Latency & Availability column to Y.  
10. Select Save.  
To configure these options, Service Type on the Easy Install screen must be set to  
Frame Relay.  
Table 3-3. Class of Service Definitions  
Class of Svc Name  
Possible Settings: ASCII Text Entry  
Default Setting:  
For IDs 2–7: blank  
For ID 1: Default  
Specifies a name to identify a Class of Service definition.  
ASCII Text Entry Enter a unique name for the definition (maximum length  
8 characters).  
Measure Latency & Availability  
Possible Settings: N, Y  
Default Setting:  
For IDs 2–7: N  
For ID 1: Y  
Determines whether latency and availability are measured for this Class of Service ID.  
Display Conditions – This option is set to N and is read-only until the class of service is  
defined and code points are assigned to it.  
N – Latency and availability are not measured for this Class of Service ID.  
Y – Latency and availability are measured for this Class of Service ID.  
Code Points Assigned  
Possible Settings: Y, N  
Default Setting:  
For IDs 2–7: N  
For ID 1: Y  
This read-only field shows whether a Code Point has been assigned to this Class of  
Service ID on the Code Point Definitions screen.  
N – No Code Point is assigned to this ID.  
Y – At least one Code Point is assigned to this ID.  
9000-A2-GB31-00  
December 2002  
3-9  
 
3. Configuration Options  
Code Point Definitions  
Select Class of Service Definitions from the System menu, then PgDn or PgUp, to  
display or change the Code Point definitions for a Class of Service ID. See  
Table 3-4. Code Point Definitions  
Code Pnt  
Possible Settings: 000000–111111  
Default Setting: None.  
This read-only field shows the possible Code Points. Code Points are described in  
RFC 2474.  
ID  
Possible Settings: 1–7  
Default Setting: 1  
This read-only field shows the ID associated with the Name field. If you change a name in  
a Name field on this screen and select Save, the ID changes to match the name.  
Name  
Possible Settings: ASCII Text  
Default Setting: Default  
The Name field specifies the Class of Service to which you want to assign the Code Point.  
ASCII Text – Specifies one of the Class of Service Names entered on the Class of  
Service Definitions screen.  
3-10  
December 2002  
9000-A2-GB31-00  
 
   
3. Configuration Options  
Configuring Service Level Verification Options  
SLV options are selected from the System menu (see Table 3-5, Service Level  
Main MenuConfigurationSystemService Level Verification  
Table 3-5. Service Level Verification Options (1 of 3)  
SLV Sample Interval (secs)  
Possible Settings: 10 – 3600  
Default Setting: 60  
Sets the inband communications interval between FrameSaver SLV devices. Inband  
communications are used to pass frames that calculate latency, as well as transmission  
success and other SLV information.  
10 – 3600 – Sets the SLV Sample Interval (secs) in seconds.  
SLV Synchronization Role  
Available Settings: Tributary, Controller, None  
Default Setting: Tributary  
Determines the role the unit plays in maintaining synchronization of user history data  
collection and storage between FrameSaver devices.  
Tributary – Uses network timing received from incoming SLV communications and  
provides network-based synchronization information to other devices in the network.  
Controller – Uses its own internal time-of-day clock and provides synchronization  
information to other devices in the network based upon its own clock.  
NOTE: Only one device in the network should be configured as the SLV  
synchronization controller.  
None – Incoming timing information is ignored and no timing information is sent out. This  
setting should only be used when network synchronization is not desirable, or when a  
single unit connects multiple networks or network segments.  
SLV Type  
Available Settings: Standard, COS 1–COS 7  
Default Setting:  
If SLV Feature is enabled: Standard  
If SLV Feature is disabled: COS 1  
Determines the type of SLV measurements to which these other SLV options apply:  
SLV Timeout Error Event Threshold  
SLV Timeout Clearing Event Threshold  
SLV Round Trip Latency Error Threshold  
SLV Latency Clearing Event Threshold  
SLV Packet Size  
Standard – The options selected apply to standard FrameSaver SLV measurements,  
utlizing an EDLCI for FrameSaver-to-FrameSaver communication. This option is not  
available if the SLV Feature is disabed or if Service Type is PPP.  
COS 1–COS 7 – The options selected apply to this Class of Service. Different settings  
may be saved for each Class of Service.  
9000-A2-GB31-00  
December 2002  
3-11  
 
                 
3. Configuration Options  
Table 3-5. Service Level Verification Options (2 of 3)  
SLV Delivery Ratio  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Determines whether communication of Frame and Data Delivery Ratios (FDR/DDR)  
between FrameSaver SLV devices is enabled. To use this capability, both ends of all  
PVCs must be FrameSaver SLV devices. If some of the units are FrameSaver 9124s or  
9624s, they must be running software version 1.2 or higher.  
Display Conditions – This option appears only if SLV Type is Standard and Service  
Type is not PPP.  
Enable – An extra byte for FDR/DDR statistics collection is included with each frame,  
which is used at the receiving end to determine the amount of data dropped by the  
network.  
Disable – Extra byte is not included.  
DLCI Down on SLV Timeout  
Available Settings: Enable, Disable  
Default Setting: Disable  
Determines whether missed SLV packets will be monitored along with the LMI status to  
determine the status of PVC connections to remote FrameSaver units.  
NOTE: This option does not apply to multiplexed DLCIs connected to a far-end unit  
with hardware bypass capability.  
Display Conditions – This option appears only if SLV Type is Standard and Service  
Type is not PPP.  
Enable – After the configured threshold for missed SLV packets has been exceeded,  
causing the DLCI’s status to turn Inactive, an alarm and SNMP trap are generated, and a  
Health and Status message created.  
Disable – Missed SLV packets are monitored, but the DLCI is not declared down.  
SLV Timeout Error Event Threshold  
Available Settings: 1, 2, 3, 4 . . . 20  
Default Setting: 3  
Specifies the number of consecutive missed SLV communications that must be detected  
before a DLCI Inactive status is declared.  
1–20 – Sets the limit for these error events.  
SLV Timeout Clearing Event Threshold  
Available Settings: 1, 2, 3, 4 . . . 20  
Default Setting: 1  
Specifies the number of consecutive SLV messages that must be received before the  
DLCI Inactive status is cleared.  
1 – 20 – Sets the limit for the clearing event.  
3-12  
December 2002  
9000-A2-GB31-00  
 
         
3. Configuration Options  
Table 3-5. Service Level Verification Options (3 of 3)  
SLV Round Trip Latency Error Threshold (ms)  
Available Settings: 50, 51, 52, . . . 10000  
Default Setting: 10000  
Specifies the number of milliseconds that must be exceeded before an SLV Latency  
Threshold alarm event is declared and backup, if configured, is initiated for a DLCI.  
If SLV Type is Standard, the latency applies to a multiplexed DLCI.  
If SLV Type is a Class of Service (COS 1 – COS 7), the latency applies to the COS on an  
IP Enabled path.  
50–10000 – Sets the limit for these error events.  
SLV Latency Clearing Event Threshold  
Available Settings: 1, 2, 3, 4 . . . 20  
Default Setting: 2  
Specifies the number of consecutive SLV latency measurements below the error  
threshold that must be received before the error status is cleared.  
1 – 20 – Sets the limit for the clearing event.  
SLV Packet Size (bytes)  
Available Settings: 64 – 2048  
Default Setting: 64  
Sets the size of packets, in bytes, that will be used for SLV communications. SLV packets  
are used to track latency and other SLV-related variables.  
When the packet size is changed, a new round trip and average latency calculation must  
be performed, so these measurements will not appear on the SLV Performance Statistics  
screen until a new sampling interval has occurred.  
64 – 2048 – Sets the packet size for SLV communications.  
9000-A2-GB31-00  
December 2002  
3-13  
 
       
3. Configuration Options  
Configuring General System Options  
Select General from the System menu to configure the general system  
configuration options (see Table 3-6, General System Options).  
Main MenuConfigurationSystemGeneral  
Table 3-6. General System Options (1 of 3)  
Test Timeout  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Determines whether or not loopback and pattern tests have a duration after which they  
are terminated automatically.  
Enable – All Loopback and Pattern tests have a timeout. This setting is recommended  
when the FrameSaver unit is managed remotely through an in-band data stream. If the  
FrameSaver unit is accidently commanded to execute a disruptive test on the interface  
providing the management access, control can be regained after the timeout expires,  
terminating the test.  
Disable – Loopback and pattern tests must be manually terminated.  
Test Duration (min)  
Possible Settings: 1 – 120  
Default Setting: 10  
Specifies the maximum duration of the tests.  
Display Conditions – This option only appears when Test Timeout is set to Enable.  
1 – 120 – Sets the Test Timeout period in minutes (inclusive).  
Primary Clock Source  
Possible Settings: Net1, DSX, Internal, DBM  
Default Setting: Net1  
Allows you to select the primary clock source for the unit. The source selected provides all  
of the timing within the FrameSaver unit and the clocks for all of the external interfaces.  
Failure of the clock specified by this configuration option results in automatic fallback to  
the Secondary Clock Source configuration option setting.  
NOTE: For the Primary and Secondary Clock Source options, only Internal can be  
selected for both options. All other selections must have different settings (e.g., if  
Primary Clock Source is set to Net1, Secondary Clock Source cannot be set to Net1).  
Net1 – The primary clock is derived from the Network1 T1 interface.  
DSX – The primary clock for the unit is derived from the DSX-1 interface. This setting only  
appears if the DSX-1 interface is enabled (see Configuring the T3 User Port (9520-ILM)  
Internal – The primary clock is the internal clock.  
DBM – The primary clock is derived from the DBM. This selection only appears if the DBM  
is installed and enabled.  
3-14  
December 2002  
9000-A2-GB31-00  
 
               
3. Configuration Options  
Table 3-6. General System Options (2 of 3)  
Secondary Clock Source  
Possible Settings: Net1, DSX, Internal, DBM  
Default Setting: Internal  
Provides a secondary clock source when the primary clock source fails. The source  
selected for this configuration option provides all of the timing within the unit and the  
clocks for all of the external interfaces.  
The clock source will switch back to primary when the primary clock source returns and is  
stable for 10 seconds. If the secondary clock source fails, the clock source will switch to  
internal. The clock source will switch back to primary when the primary clock source  
returns and is stable for 10 seconds.  
NOTE: For the Primary and Secondary Clock Source options, only Internal can be  
selected for both options. All other selections must have different settings (e.g., if  
Primary Clock Source is set to Net1, Secondary Clock Source cannot be set to Net1).  
Net1 – The secondary clock is derived from the Network1 T1 interface.  
DSX – The secondary clock for the unit is derived from the DSX-1 interface. This setting  
only appears if the DSX-1 interface is enabled.  
Internal – The secondary clock is the internal clock.  
DBM – The secondary clock is derived from the DBM. This selection only appears if the  
DBM is installed and enabled.  
9000-A2-GB31-00  
December 2002  
3-15  
 
   
3. Configuration Options  
Table 3-6. General System Options (3 of 3)  
System Alarm Relay  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Specifies whether an alarm condition for the unit will activate the system alarm relay. The  
alarm relay is deactivated when the condition causing the alarm is corrected. If more than  
one alarm condition is present, the alarm relay remains active until all alarm conditions  
are cleared.  
You can also deactivate an alarm via the System Alarm Relay Cut-Off selection from the  
Control menu; however, the alarm itself is not cleared. When another alarm condition is  
detected, the alarm is reactivated again, requiring another manual deactivation of the  
alarm relay.  
Display Conditions – This option only appears for a FrameSaver SLV 9128 installed in  
the 9000 Series Access Carrier.  
Alarm conditions are:  
Alarm Indication Signal (AIS) received at the Network, DSX-1, or PRI interface  
Continuous Loss of Signal (LOS) condition at the Network, DSX-1, or PRI interface  
CTS Down  
DBM Download Required  
DBM BRI Card Failed  
Device Fail  
DLCI Down  
DTR Down  
Ethernet Link Down  
Excessive Error Rate (EER) detected at the Network or PRI interface  
Internal Modem Failed  
ISDN Network Failure  
LMI Down  
Network Communication Link Down  
Out of Frame (OOF) at Network, DSX-1, or PRI  
Primary or Secondary Clock Failure  
Power Supply/Fan Failure  
RTS Down  
Self-Test Failure  
SLV Latency Exceeded  
SLV Timeout  
Suboptimal (Maximum) Link Rate Cannot be Achieved  
Two Level-1 Users Accessing Device  
Yellow Alarm Signal on the Network, DSX-1, or PRI interface  
Enable – Activates alarm conditions on the system alarm relay when an alarm condition  
occurs.  
Disable – Does not activate the system alarm relay when an alarm condition occurs.  
3-16  
December 2002  
9000-A2-GB31-00  
 
 
3. Configuration Options  
Configuring Physical Interfaces  
Characteristics for physical interfaces are explained in the following sections:  
n
n
n
n
n
Configuring the Network Interface  
When configuring the physical characteristics for the network interface, select  
Physical from the Network menu.  
Main MenuConfigurationNetworkPhysical  
See:  
n
n
n
n
n
n
n
Table 3-8, T3 Network Physical Interface Options (9520, 9520-ILM)  
Table 3-9, DDS Network Physical Interface Options (9623, 9626)  
Table 3-10, IDSL Network Physical Interface Options (9720)  
Table 3-12, SHDSL Network Physical Interface Options (9788, 9788 Router)  
Table 3-13, Synchronous Network Data Port Physical Interface Options  
(9820-2M, 9820-8M)  
n
9000-A2-GB31-00  
December 2002  
3-17  
 
       
3. Configuration Options  
T1 Network Interface  
FrameSaver Models 9123, 9126, and 9128 have a T1 network interface.  
Table 3-7. T1 Network Physical Interface Options (1 of 4)  
Line Framing Format  
Possible Settings: D4, ESF  
Default Setting: ESF  
Specifies the framing format for transmitted and received signals on the T1 network  
interface.  
D4 – Uses D4 framing format.  
NOTE: This setting is not recommended by network carriers. False yellow alarms may  
occur after traffic has been running and the channel returns to idle, or when there is  
light traffic when other settings are selected. ESF format does not create this problem.  
ESF – Uses Extended Superframe framing format.  
Line Coding Format  
Possible Settings: AMI, B8ZS  
Default Setting: B8ZS  
Specifies the line coding format for the network interface.  
AMI – Uses Alternate Mark Inversion (AMI) line coding format.  
B8ZS – Uses Bipolar 8 Zero Substitution (B8ZS) line coding format.  
Line Build Out  
Possible Settings: 0.0, –7.5, –15, –22.5  
Default Setting: 0.0  
Specifies the line build out for the signal transmitted to the network.  
0.0, –7.5, –15, –22.5 – Specifies line build out in dB.  
Bit Stuffing  
Possible Settings: 62411, Disable  
Default Setting: 62411  
Determines the type of bit insertion to provide ones density requirements for data  
transmitted to the network.  
Display Conditions – This option does not appear when Line Coding Format is set to  
B8ZS.  
62411 – Inserts a one in the data after 15 consecutive zeros are received or the density of  
ones falls below 12.5%. This setting complies with AT&T TR 62411, but is not  
recommended for frame relay data because it inserts errors in the data traffic.  
Disable – Disables bit stuffing. Ones density is not enforced on data sent to the network.  
3-18  
December 2002  
9000-A2-GB31-00  
 
               
3. Configuration Options  
Table 3-7. T1 Network Physical Interface Options (2 of 4)  
Transmit Timing  
Possible Settings: System, Interface  
Default Setting: System  
Allows transmit timing to be selected from either the system master clock source or from  
the currently selected interface.  
System – Transmit timing is derived from the current system clock source (see Table 3-6,  
Interface – Transmit timing is derived from this interface.  
NOTE: When Interface is configured, the clock must be synchronized to the system  
clock source.  
Network Initiated LLB  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Allows the initiation and termination of the line loopback (LLB) to be controlled by the  
receipt of LLB-Actuate and LLB-Release commands from the network.  
Enable – LLB is controlled by LLB-Actuate and LLB-Release commands. Receiving a  
LLB-Actuate command causes the FrameSaver unit to enter a line loopback (provided an  
LLB can be performed in the FrameSaver unit’s current state). Receiving an LLB-Release  
command terminates the LLB.  
Disable – The FrameSaver unit ignores the LLB-Actuate and LLB-Release commands.  
NOTE: When disabled, the system is not in compliance with ANSI T1.403 or  
AT&T TR 62411.  
Network Initiated PLB  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Allows the initiation and termination of the payload loopback (PLB) to be controlled by the  
receipt of PLB-Actuate and PLB-Release commands from the network.  
Display Conditions – This option only appears when Line Framing Format is set to  
ESF.  
Enable – PLB is controlled by PLB-Actuate and PLB-Release commands. Receiving a  
PLB-Actuate command causes the system to enter a payload loopback (provided a PLB  
can be performed in the unit’s current state). Receiving a PLB-Release command  
terminates the PLB.  
Disable – The FrameSaver unit ignores the PLB-Actuate and PLB-Release commands.  
NOTE: When disabled, the unit is not in compliance with ANSI T1.403 or  
AT&T TR 54016.  
9000-A2-GB31-00  
December 2002  
3-19  
 
     
3. Configuration Options  
Table 3-7. T1 Network Physical Interface Options (3 of 4)  
Network Initiated DCLB  
Possible Settings: Disable, V.54_&_ANSI  
Default Setting: V.54_&_ANSI  
Allows the initiation and termination of the Data Channel Loopback (DCLB V.54 Loop 2) to  
be controlled by the receipt of a DCLB-actuate or DCLB-release sequence (either V.54 or  
FT1-ANSI compliant) from the network on the DS0s used for the network frame relay link.  
When enabled and a DCLB-activate sequence is received, the unit initiates a DCLB on  
the network interface. When a DCLB-release sequence is received, the DCLB is stopped.  
Disable – DCLB-actuate and DCLB-release sequences are ignored.  
V.54_&_ANSI – DCLB-actuate and DCLB-release sequences that comply with either V.54  
or ANSI T1.403, Annex B standard will be recognized and will control initiation and  
termination of a DCLB for the network frame relay link. The actuate and release  
sequences do not need to match (for example, a DCLB started with a V.54 actuate  
sequence can be stopped with an FT1 release sequence).  
ANSI Performance Report Messages  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Specifies whether ANSI T1.403 compliance performance report messages (PRMs) are  
generated and sent to the network over the ESF facility data link every second.  
Display Conditions – This option only appears when Line Framing Format is set to  
ESF.  
Enable – Generates and sends PRMs.  
Disable – Does not generate and send PRMs.  
3-20  
December 2002  
9000-A2-GB31-00  
 
       
3. Configuration Options  
Table 3-7. T1 Network Physical Interface Options (4 of 4)  
Excessive Error Rate Threshold  
Possible Settings: 10E-4, 10E-5, 10E-6, 10E-7, 10E-8, 10E-9  
Default Setting: 10E-4  
Sets the error rate threshold that determines when an EER condition is declared. The  
excessive error rate is determined by the ratio of the number of CRC6 errors to the total  
number of bits received over a set period of time.  
Display Conditions – This option only appears when Line Framing Format is set to  
ESF.  
10E-4 – Declares an EER if more than 1,535 CRC6 errors are detected in a 10 second  
period. Clears when fewer than 1,536 CRC6 errors are detected within the same time  
period.  
10E-5 – Declares an EER if more than 921 CRC6 errors are detected in a 60 second  
period or a 10-4 condition occurs. Clears when fewer than 922 CRC6 errors are detected  
within the same time period.  
10E-6 – Declares an EER if more than 92 CRC6 errors are detected in a 60 second period  
or a 10-5 or 10-4 condition occurs. Clears when fewer than 93 CRC6 errors are detected  
within the same time period.  
10E-7 – Declares an EER if more than 9 CRC6 errors are detected in a 60 second period  
or a 10-6, or 10-5, or 10-4 condition occurs. Clears when fewer than 10 CRC6 errors are  
detected within the same time period.  
10E-8 – Declares an EER if more than 41 CRC6 errors are detected in three 15 minute  
intervals or a 10-7, 10-6, 10-5, 10-4 condition occurs. Clears when fewer than 42 CRC6  
errors are detected within the same time period.  
10E-9 – Declares an EER if more than 4 CRC6 errors are detected in three 15 minute  
intervals or a 10-8, 10-7, 10-6, 10-5, or 10-4 condition occurs. Clears when fewer than  
5 CRC6 errors are detected within the same time period.  
Circuit Identifier  
Possible Settings: ASCII Text Entry, Clear  
Default Setting: blank  
Identifies the transmission vendor’s circuit information to facilitate troubleshooting.  
ASCII Text Entry – Edit or display circuit identifier information (maximum 255 characters).  
Clear – Removes the circuit identifier information.  
9000-A2-GB31-00  
December 2002  
3-21  
 
   
3. Configuration Options  
T3 Network Interface  
FrameSaver Models 9520 and 9520-ILM have a T3 network interface.  
Table 3-8. T3 Network Physical Interface Options  
Circuit Identifier  
Possible Settings: ASCII Text Entry, Clear  
Default Setting: blank  
Identifies the transmission vendor’s circuit information to facilitate troubleshooting.  
ASCII Text Entry – Edit or display circuit identifier information (maximum 255 characters).  
Clear – Removes the circuit identifier information.  
Line Build Out  
Possible Settings: Short, Long  
Default Setting: Short  
Specifies the line build out for the signal transmitted to the network.  
Short – Activates an equalization filter to simulate a longer cable. Use this option for a  
network cable less than 100 feet.  
Long – The equalization filter is bypassed. Use this option for a network cable 100 feet or  
longer.  
Network Initiated LLB  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Allows the initiation and termination of the line loopback (LLB) to be controlled by the  
receipt of LLB-Actuate and LLB-Release commands from the network.  
Enable – LLB is controlled by LLB-Actuate and LLB-Release commands. Receiving a  
LLB-Actuate command causes the FrameSaver unit to enter a line loopback (provided an  
LLB can be performed in the FrameSaver unit’s current state). Receiving an LLB-Release  
command terminates the LLB.  
Disable – The FrameSaver unit ignores the LLB-Actuate and LLB-Release commands.  
3-22  
December 2002  
9000-A2-GB31-00  
 
             
3. Configuration Options  
DDS Network Interface  
FrameSaver Models 9623 and 9626 have a DDS network interface.  
Table 3-9. DDS Network Physical Interface Options (1 of 2)  
Transmit Timing  
Possible Settings: Internal, Receive  
Default Setting: Receive  
Specifies the unit’s timing source based upon how the unit will be used. When the unit is  
connected to a DDS (Digital Data Service) network for standard operation, timing is  
provided by the network. In a LADS, or LDM, application (local area data set/limited  
distance modem), where local and remote FrameSaver units are directly connected, one  
of the units provides timing for both units.  
Internal – Timing for the unit and its attached LADS partner is derived from the unit’s  
internal clock. Use this setting when the unit will be used as a LADS primary timing unit,  
where the FrameSaver unit establishes overall timing for the two interconnected units.  
Receive – Timing for the unit is derived from the network Received signal. Use this setting  
for standard DDS operation, or when the unit will be used as a LADS secondary timing  
unit. See DDS Line Rate (Kbps).  
DDS Line Rate  
Possible Settings: Auto_On_No_Signal, Initialize_From_Network, 56, 64CC  
Default Setting: Auto_On_No_Signal  
Configures the network interface’s line speed to match the Digital Data Service’s (DDS’s)  
line speed. This is the rate at which data is transmitted over the DDS line.  
Display Conditions – This option only appears when Transmit Timing is set to Receive.  
Auto_On_No_Signal – Automatically detects the line rate on the network interface  
whenever a No Signal alarm is declared, the unit is reset, or the line rate is changed to  
Auto_On_No_Signal and saved, then changes the unit’s operating rate to match the  
network’s. It may take up to 15 seconds each time automatic rate detection and  
adjustment occurs.  
Initialize_From_Network – Automatically detects the line rate on the network interface  
once, then changes the unit’s operating rate to match the network’s. Automatic rate  
detection and adjustment, or Autobaud, will not occur again unless the line rate is  
changed to Initialize_From_Network or Auto_On_No_Signal and saved. It may take up to  
15 seconds for automatic rate detection and adjustment to occur.  
56 – Forces the line rate to 56 Kbps.  
64CC – Forces the line rate to 64 Kbps Clear Channel (72 Kbps on the line).  
9000-A2-GB31-00  
December 2002  
3-23  
 
                     
3. Configuration Options  
Table 3-9. DDS Network Physical Interface Options (2 of 2)  
Network Initiated DCLB  
Possible Settings: Disable, V.54_&_ANSI  
Default Setting: V.54_&_ANSI  
Allows the initiation and termination of the Data Channel Loopback (DCLB V.54 loop 2) to  
be controlled by the receipt of a DCLB-actuate or DCLB-release sequence (either V.54 or  
FT1-ANSI compliant) from the network or a far-end FrameSaver device. When enabled  
and a DCLB-activate sequence is received, the unit initiates a DCLB on the network  
interface. When a DCLB-release sequence is received, the DCLB is stopped.  
Disable – DCLB-actuate and DCLB-release sequences are ignored.  
V.54_&_ANSI – DCLB-actuate and DCLB-release sequences that comply with either V.54  
or ANSI T1.403, Annex B standard will be recognized and will control initiation and  
termination of a DCLB for this frame relay link. The actuate and release sequences do not  
need to match (for example, a DCLB started with a V.54 actuate sequence can be  
stopped with an FT1 release sequence).  
DSU Latching Loopback  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Specifies whether the FrameSaver unit responds to the DSU Latching Loopback  
sequence sent by the network, as specified by TR62310.  
Enable – Responds to DSU latching loopback commands. The unit remains in loopback  
until the network receives the loopback release sequence.  
Disable – Does not respond to the DSU loopback commands, or terminates the latching  
loopback test if it is active.  
NOTE: Because the latching loopback code is a control sequence, as opposed to a  
bipolar violation sequence, user data may activate the loopback. Disable this option to  
stop an unintentional latching loopback.  
Require DSU Latching Loopback Preamble  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Specifies whether the FrameSaver unit requires the ANSI or FRF proposed preamble for  
the network-initiated DSU Latching Loopback when detecting the loopback sequence.  
Display Conditions – This option only applies when the unit is operating on a standard  
DDS 64KCC circuit and DSU Latching Loopback (64KCC) is enabled.  
Enable – Does not respond to the DSU Latching Loopback commands unless the  
preamble is received.  
Disable – Responds to DSU Latching Loopback commands, whether or not the preamble  
is received.  
3-24  
December 2002  
9000-A2-GB31-00  
 
           
3. Configuration Options  
IDSL Network Interface  
FrameSaver Model 9720 has an IDSL network interface.  
Table 3-10. IDSL Network Physical Interface Options  
Operating Rate  
Possible Settings: AutoRate, 64, 128, 144  
Default Setting: AutoRate  
Specifies the IDSL line rate.  
AutoRate – The line rate is automatically detected when the frame relay LMI is brought  
up on one or both channels.  
64 – The line rate is 64 kbps. One B channel is used for the data transfer, and automatic  
rate detection is disabled.  
128 – The line rate is 128 kbps. Both B channels are used for the data transfer, and  
automatic rate detection is disabled.  
144 – The line rate is 144 kbps. Both B channels are used for the data transfer, and  
automatic rate detection is disabled.  
Channel  
Possible Settings: B1, B2  
Default Setting: B1  
Specifies the B channel used for data transfer when the line rate is 64 kbps.  
Display Conditions – Channel appears only when Operating Rate is set to 64.  
B1 – The B1 channel is used for data transfer.  
B2 – The B2 channel is used for data transfer.  
9000-A2-GB31-00  
December 2002  
3-25  
 
         
3. Configuration Options  
SDSL Network Interface  
The FrameSaver DSL 9783 CSU/DSU and Router have an SDSL network  
interface.  
Table 3-11. SDSL Network Physical Interface Options  
Line Rate Mode  
Possible Settings: Hunt, AutoRate, Fixed  
Default Setting: AutoRate  
Specifies the mode to be used for rate selection.  
Hunt – The unit attempts to train at rate specified by DSL Line Rate. If that fails, the unit  
attempts to train at the next higher rate, and, if unsuccessful, cycles through all the rates  
until training is successful or the unit is reset.  
AutoRate – The unit automatically detects the line rate from the network interface.  
Fixed – The unit uses the line rate specified by DSL Line Rate.  
DSL Line Rate (Kbps)  
Possible Settings:  
If DSLAM Type is set to Paradyne, or if DSLAM Type is set to Nokia and Line Rate  
Mode is set to Fixed: 144, 192, 208, 256, 272, 384, 400, 512, 528, 768, 784,  
1024, 1152, 1168, 1536, 1552, 2320  
If DSLAM Type is set to Alcatel (NewBridge): 208, 400, 784, 1168, 1552, 2320  
– If DSLAM Type is set to Nokia and Line Rate Mode is set to Hunt: 192, 384, 768,  
1152, 1536  
If DSLAM Type is set to PairGain: 144, 192, 208, 256, 272, 384, 400, 512, 528,  
768, 784, 1024, 1152, 1168, 1536, 1552, 2320  
Default Setting:  
– If DSLAM Type is set to Alcatel (NewBridge) and Line Rate Mode is set to Hunt: 208  
– If DSLAM Type is set to Nokia and Line Rate Mode is set to Hunt: 384  
If DSLAM Type is set to PairGain and Line Rate Mode is set to Fixed: 784  
(If DSLAM Type is set to Paradyne, Line Rate Mode is set to AutoRate and DSL  
Line Rate does not appear)  
Determines the rate on the DSL network interface (if Line Rate Mode is Fixed), or the rate  
the device will first use to attempt to train (if Line Rate Mode is Hunt).  
Display Conditions – DSL Line Rate does not appear if DSL Line Rate Mode is set to  
AutoRate.  
144 – 2320 – The DSL line rate is set to the specified rate in Kbps.  
SNR Margin Alarm Threshold (dB)  
Possible Settings: –5, –4, –3, –2, –1, 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10  
Default Setting: 3  
Specifies the level in decibels at which a Signal to Noise Ratio (SNR) margin alarm  
condition is declared.  
–5 – 10 – Specifies the threshold level in dB.  
3-26  
December 2002  
9000-A2-GB31-00  
 
                   
3. Configuration Options  
SHDSL Network Interface  
The FrameSaver DSL 9788 CSU/DSU and Router have an SHDSL network  
interface.  
Table 3-12. SHDSL Network Physical Interface Options (1 of 2)  
Line Rate Mode  
Possible Settings: AutoRate, Fixed  
Default Setting: AutoRate  
Specifies the mode to be used for rate selection.  
AutoRate – The unit automatically detects the line rate from the network interface.  
Fixed – The unit uses the line rate specified by DSL Line Rate.  
DSL Line Rate (Kbps)  
Possible Settings:  
If PSD Mask is Symmetric: 200, 264, 328, 392, 456, 520, 584, 648, 712, 776, 784,  
840, 904, 968, 1032, 1096, 1160, 1224, 1288, 1352, 1416, 1480, 1544, 1552, 1608,  
1672, 1736, 1800, 1864, 1928, 1992, 2056, 2120, 2184, 2248, 2312  
If PSD Mask is Asymmetric (available in future release) and Region is Annex A:  
776, 784, 1544, 1552  
If PSD Mask is Asymmetric (available in future release) and Region is Annex B:  
2056, 2312  
Default Setting: [Depends on settings of Line Rate Mode, PSD Mask, and Region]  
Determines the rate on the DSL network interface. Valid rates, and the rates presented on  
the screen, depend on the values of Region and PSD Mask. If a change to another  
configuration option renders the selected DSL Line Rate invalid, the Line Rate Mode is set  
to AutoRate.  
Display Conditions – DSL Line Rate does not appear if DSL Line Rate Mode is set to  
AutoRate.  
200 – 2312 – The DSL line rate is set to the specified rate in Kbps.  
Region  
Possible Settings: Annex A, Annex B  
Default Setting: [Depends on model]  
Determines the annex of the G.991.2 recommendation that the unit will conform to. The  
value of Region in part determines what DSL Line Rates are available. If a change in the  
Region renders the current DSL Line Rate invalid, the Line Rate Mode is set to AutoRate.  
Annex A – The unit conforms to Annex A (for North America).  
Annex B – The unit conforms to Annex B (for Europe).  
9000-A2-GB31-00  
December 2002  
3-27  
 
             
3. Configuration Options  
Table 3-12. SHDSL Network Physical Interface Options (2 of 2)  
PSD Mask  
Possible Settings: Symmetric  
Default Setting: Symmetric  
Read-only. Specifies the Power Spectral Density (PSD) mask the unit will use. The value  
of PSD Mask in part determines what DSL Line Rates are available. If a change in the  
PSD Mask setting (available in a future release) renders the current DSL Line Rate  
invalid, the Line Rate Mode is set to AutoRate.  
Asymmetric – (Future use.) The unit uses the asymmetric PSD mask.  
Symmetric – The unit uses the symmetric PSD mask.  
Synchronous Network Interface  
FrameSaver Models 9820-2M and 9820-8M have an EIA-530-A network interface.  
Table 3-13. Synchronous Network Data Port Physical Interface Options (1 of 2)  
Port Type  
Possible Settings: E530, V.35, X.21  
Default Setting: V.35  
Selects the type of port to be used for the network data port.  
E530 – The port is configured as an EIA-530-A-compatible DTE. An  
EIA-530-A-compatible DCE can be directly connected to the DB25 connector for this port  
on the rear of the FrameSaver unit.  
V.35 – The port is configured as a V.35-compatible DTE. A V.35-compatible DCE can be  
connected to the DB25 connector for this port using an adapter cable on the rear of the  
FrameSaver unit.  
X.21 – The port is configured as a V.11/X.21-compatible DTE. A V.11/X.21-compatible  
DCE can be connected to the DB25 connector for this port using an adapter cable on the  
rear of the FrameSaver unit.  
Invert Internal Clock  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Specifies whether the internal clock (used for timing data transmitted to the DCE) will be  
phase-inverted with respect to the clock received at the interface. This option is useful  
when long cable lengths between the FrameSaver device and the DCE are causing  
errors.  
Enable – The internal clock used to transmit data to the DCE is phase inverted with  
respect to the clock supplied by the DCE to this port.  
Disable – The internal clock is not inverted (normal).  
3-28  
December 2002  
9000-A2-GB31-00  
 
           
3. Configuration Options  
Table 3-13. Synchronous Network Data Port Physical Interface Options (2 of 2)  
Monitor DSR  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Specifies whether the state of the DCE Ready (DSR) circuit on the network data port will  
be used to determine when valid data communication is possible with the unit. When this  
condition is detected, an alarm is generated, LMI is declared down, and no further transfer  
of frame relay data can occur on this interface.  
Display Conditions – This option does not appear when Port Type is set to X.21. The  
signal is assumed to be asserted.  
Enable – Interchange circuit CC (ITU/CCITT 107) – DSR is monitored to determine when  
valid data is being sent from the DCE.  
Disable – DSR is not monitored. DSR is assumed to be asserted and data is transmitted,  
regardless of the actual state of the lead.  
Monitor CTS  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Specifies whether the state of the Clear to Send (CTS) circuit on the network data port will  
be used to determine when valid data communication is possible with the unit. When this  
condition is detected, an alarm is generated, LMI is declared down, and no further transfer  
of frame relay data can occur on this interface.  
Display Conditions – This option does not appear when Port Type is set to X.21. The  
signal is assumed to be asserted.  
Enable – Interchange circuit CB (ITU/CCITT 106) – CTS is monitored to determine  
whether data should be transmitted to the DCE.  
Disable – CTS is not monitored. CTS is assumed to be asserted and data is transmitted,  
regardless of the actual state of the lead.  
Monitor RLSD  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Specifies whether the state of the Received Line Signal Detector (RLSD) circuit on the  
network data port will be used to determine when valid data communication is possible  
with the unit. When this condition is detected, an alarm is generated, LMI is declared  
down, and no further transfer of frame relay data can occur on this interface.  
If Port Type is set to X.21, the Indication interchange circuit is monitored instead of RLSD.  
Enable – Interchange circuit CF (ITU/CCITT 109) – RLSD is monitored to determine  
when valid data communication is possible with the DCE.  
Disable – RLSD is not monitored. RLSD is assumed to be asserted and data is  
transmitted, regardless of the actual state of the lead.  
9000-A2-GB31-00  
December 2002  
3-29  
 
     
3. Configuration Options  
HSSI Network Interface  
FrameSaver Model 9820-45M has a HSSI network interface.  
Table 3-14. HSSI Network Data Port Physical Interface Options  
Monitor DSR  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Specifies whether the state of the DCE Ready (DSR) circuit on the network data port will  
be used to determine when valid data communication is possible with the unit. When this  
condition is detected, an alarm is generated, LMI is declared down, and no further transfer  
of frame relay data can occur on this interface.  
Enable – Interchange circuit CC (ITU/CCITT 107) – DSR is monitored to determine when  
valid data is being sent from the DCE.  
Disable – DSR is not monitored. DSR is assumed to be asserted and data is transmitted,  
regardless of the actual state of the lead.  
3-30  
December 2002  
9000-A2-GB31-00  
 
         
3. Configuration Options  
Configuring a User Data Port (CSU/DSUs)  
Select Physical from the Data Ports menu to display or change the physical  
characteristics of the data port connected to the DTE.  
Main MenuConfigurationData PortsPhysical  
See:  
n
n
n
V.35 Data Port Physical Interface  
FrameSaver Models 9123, 9126, 9623, 9626, and 9783 have a V.35 data port.  
The Model 9128 standalone and carrier-mounted units have two V.35 data ports.  
Table 3-15. V.35 Data Port Physical Interface Options (1 of 6)  
Port Status  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Determines whether the data port is being used and can be configured.  
Enable – The port is active, and can be used to transmit and receive data.  
Disable – The port is not active. When the port is disabled, the following will occur:  
No alarms or traps configured for the port will be generated.  
LED for the port will be held in an Off state.  
No – The operation is canceled. (Pressing either the Esc or Ctrl-a key also acts as a  
No.)  
Yes – Port status is disabled.  
Port Type (9788, 9820-2M, 9820-8M)  
Possible Settings: E530, V.35, X.21  
Default Setting: V.35  
Specifies the port type of the data port.  
E530 – The port is configured as an EIA-530-A-compatible DCE. An EIA-530-A-  
compatible DTE may be directly connected to the DB25 connector for the port.  
V.35 – The port is configured as a V.35-compatible DCE. A V.35-compatible DTE may be  
connected to the port using a DB25-to-MS34 adapter.  
X.21 – The port is configured as an X.21-compatible DCE. An X.21-compatible DTE may  
be connected to the port using a DB25-to-DB15 adapter.  
9000-A2-GB31-00  
December 2002  
3-31  
 
             
3. Configuration Options  
Table 3-15. V.35 Data Port Physical Interface Options (2 of 6)  
Port Use (9128)  
Possible Settings: Frame Relay, Synchronous Data  
Default Setting:  
Frame Relay when the port supports frame relay.  
Synchronous Data when the port only supports synchronous data.  
Determines how the data port will be used.  
Display Conditions – This option only appears for user data on Port-2, and only when  
Service Type is Frame Relay.  
Frame Relay – The port is configured for frame relay traffic. Frame relay links, DLCis, and  
PVC connections can be configured on this port.  
Synchronous Data – The port is configured for standard TDM data, and can be  
cross-connected to a time slot on a T1 interface.  
No alarms or traps configured for the port will be generated.  
The LED for the port will be held in an Off state.  
Existing cross-connect assignments associated with the port are cleared.  
Max Port Rate (9128)  
Possible Settings: 1536, 2048  
Default Setting: 1536  
Specifies the maximum clock rate for a user data port. The data rate for this port is limited  
to the rate specified by this option so that the maximum rate supported by an attached  
DTE is not exceeded.  
Display Conditions – This option only appears when the Port Use is set to Frame Relay  
or PPP, the port rate is not otherwise configurable, and the selected port is Port-2.  
1536 – The maximum port rate for the port is 1536 Kbps.  
2048 – The maximum port rate for the port is 2048 Kbps.  
Port Base Rate (9128)  
Possible Settings: Nx64, Nx56  
Default Setting: Nx64  
Specifies the base rate for the data port, which is a multiple (from 1 to 24) of the base rate  
specified by this option. N is a number from 1 to 24.  
Display Conditions – This option only appears when Port Use is set to Synchronous  
Data.  
Nx64 – The base rate for the port is 64 Kbps.  
Nx56 – The base rate for the port is 56 Kbps.  
3-32  
December 2002  
9000-A2-GB31-00  
 
     
3. Configuration Options  
Table 3-15. V.35 Data Port Physical Interface Options (3 of 6)  
Invert Transmit Clock  
Possible Settings: Auto, Enable, Disable  
Default Setting: Auto  
Determines whether the clock supplied by the FrameSaver unit on interchange circuit DB  
(ITU 114) – Transmit Signal Element Timing (DCE Source) TXC is phase inverted with  
respect to the clock used to time the incoming Transmitted Data (TD).  
Auto – The port checks the clock supplied by the DCE on TXC on this port. If necessary,  
the port automatically phase inverts the clock with respect to the transmitted data.  
Enable – Phase inverts the TXC clock. Use this setting when long cable lengths between  
the FrameSaver unit and the DTE are causing data errors.  
Disable – Does not phase invert the TXC clock.  
Transmit Clock Source  
Possible Settings: Internal, External  
Default Setting: Internal  
Determines whether the DTE’s transmitted data is clocked into the FrameSaver unit by its  
internal transmit clock or by the external clock provided by the DTE.  
NOTE: Changing settings for this configuration option causes the FrameSaver unit to  
abort any physical port tests, including any DTE-initiated loopback tests.  
Internal – The FrameSaver unit uses the interchange circuit DB (ITU 114) – Transmit  
Signal Element Timing (TXC) (DCE source) for timing the incoming data.  
External – The DTE provides the clock for the transmitted data, and the FrameSaver unit  
uses the interchange circuit DA (ITU 113) – Transmit Signal Element Timing (XTXC) (DTE  
source) for timing the incoming data.  
Monitor RTS  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Specifies whether the state of the Request To Send (RTS) circuits on the user data port  
will be used to determine when valid data communication is possible with the DTE. When  
this condition is detected, CTS is deasserted, LMI is declared down, and no further  
transfer of frame relay data can occur on this interface.  
Enable – Interchange circuit CA (ITU 105) – RTS is monitored to determine when valid  
data communication is possible with the DTE.  
Disable – RTS is not monitored. RTS is assumed to be asserted and data is being  
transmitted, regardless of the state of the lead.  
9000-A2-GB31-00  
December 2002  
3-33  
 
               
3. Configuration Options  
Table 3-15. V.35 Data Port Physical Interface Options (4 of 6)  
Monitor DTR  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Specifies whether the state of the DTE Ready (DTR) circuit on the user data port will be  
used to determine when valid data communication is possible with the DTE. When this  
condition is detected, an alarm is generated, LMI is declared down, and no further transfer  
of frame relay data can occur on this interface.  
Enable – Interchange circuit CD (ITU 108/1/2) – DTR is monitored to determine whether  
data should be transmitted to the DTE.  
Disable – DTR is not monitored. DTR is assumed to be asserted and data is being  
transmitted, regardless of the state of the lead.  
Port (DTE) Initiated Loopbacks  
Possible Settings:  
For Port-1, or Port-2 when Port Use is set to Frame Relay: Disable, Local  
For Port-2 when Port Use is set to Synchronous Data: Disable, DTPLB, DCLB, Both  
Default Setting: Disable  
Possible Settings: Local, Disable  
Default Setting: Disable  
For Port-1, or Port-2 (9128 only) when Port Use is set to Frame Relay:  
Allows a local external DTE Loopback to be started or stopped via the data terminal  
equipment attached to the port’s interchange lead LL (ITU 141), as specified by V.54.  
Disable – The DTE attached to the port cannot control the local external DTE Loopback.  
Local – The DTE attached to the port controls the local external DTE Loopback.  
For Port-2 (9128 only) when Port Use is set to Synchronous Data:  
Allows local Data Terminal Loopbacks (DTPLBs) and remote Data Channel Loopbacks  
(DCLBs) to be controlled by the DTE connected to this port.  
Disable – The DTE attached to the port cannot control Local Data Terminal Loopbacks  
(DTPLBs) and remote Data Channel Loopbacks (DCLBs).  
DTPLB – The DTE attached to the port controls DTPLBs via circuit LL – CCITT 141, as  
specified by V.54. The port remains in loopback as long as the circuit stays on.  
DCLB – The DTE attached to the port controls DCLBs via circuit RL – CCITT 140, as  
specified by V.54. The far-end equipment must support inband V.54 loopbacks.  
Both – The DTE attached to the port controls both local DTPLBs and remote DCLBs.  
3-34  
December 2002  
9000-A2-GB31-00  
 
         
3. Configuration Options  
Table 3-15. V.35 Data Port Physical Interface Options (5 of 6)  
Invert Transmit and Receive Data (9128)  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Specifies whether transmitted and received data for the synchronous data port is logically  
inverted before being transmitted or after being received from the network. Use this  
configuration option for applications where data is being transported using HDLC protocol,  
whereby inverting the data ensures that the ones density requirements for the network are  
met.  
Display Conditions – This option only appears for Port-2 on a FrameSaver SLV 9128,  
when Port Use is set to Synchronous Data.  
Enable – Inverts the transmitted and received data for the port.  
Disable – Does not invert the transmitted and received data for the port.  
Action on Network Yellow Alarm (9128)  
Possible Settings: None, Halt  
Default Setting: Halt  
Specifies the action to take on the synchronous data port when a yellow alarm is received  
on the network interface. A yellow alarm indicates a problem with the signal being  
transmitted to the network.  
Display Conditions – This option only appears for Port-2 on a FrameSaver SLV 9128,  
when Port Use is set to Synchronous Data.  
None – No action taken when a yellow alarm is received.  
Halt – Halts the transmission of data received on the synchronous data port and all ones  
are sent on circuit BB (ITU 104) – Receive Data (RD) and circuit CB (ITU 106) –  
Clear-to-Send (CTS) is deasserted to the port when a yellow alarm is received.  
9000-A2-GB31-00  
December 2002  
3-35  
 
   
3. Configuration Options  
Table 3-15. V.35 Data Port Physical Interface Options (6 of 6)  
Network Initiated Data Channel Loopback (9128)  
Possible Settings: Disable, V.54, ANSI_FT1, V.54_&_ANSI  
Default Setting: Disable  
Allows the initiation and termination of the Data Channel Loopback (V.54 Loop 2) to be  
controlled by the receipt of a DCLB-actuate and DCLB-release sequence (either V.54, or  
FT1 [ANSI] compliant sequences) from the network or far end unit. When this  
configuration is enabled (V.54, FT1, or Both), receiving a DCLB-actuate sequence on a  
particular port causes the unit to initiate a DCLB on that port (provided that a DCLB can be  
performed based on the current state of the port and unit). Receiving a DCLB-release  
sequence terminates the DCLB.  
Display Conditions – This option only appears for Port-2 on a FrameSaver SLV 9128,  
when Port Use is set to Synchronous Data.  
Disable – Ignores the DCLB-actuate and DCLB-release for the port.  
V.54 – DCLB-actuate and DCLB-release sequences that comply with the V.54 standard  
for “inter-DCE signaling for point-to-point circuits” are recognized and will control the  
initiation and termination of a DCLB (V.54 Loop 2) for the port.  
ANSI_FT1 – DCLB-actuate and DCLB-release sequences that comply with either the  
ANSI.403, Annex B standard for “in-band signaling for fractional T1 (FT1) channel  
loopbacks” are recognized and will control the initiation and termination of a DCLB for the  
port.  
V.54_&_ANSI – DCLB-actuate and DCLB-release sequences that comply with either the  
ANSI or V.54 standard are recognized and will control the initiation and termination of a  
DCLB for the port.  
EIA-530-A/X.21/V.35 Data Port Physical Interface  
FrameSaver Models 9788, 9820-2M, and 9820-8M have an EIA-530-A data port  
that can be adapted for use as an X.21 or V.35 data port.  
Table 3-16. EIA-530-A/X.21/V.35 Data Port Physical Interface Options (1 of 3)  
Port Type  
Possible Settings: E530, V.35, X.21  
Default Setting: V.35  
Specifies the port type of the data port.  
E530 – The port is configured as an EIA-530-A-compatible DCE. An EIA-530-A-  
compatible DTE may be directly connected to the DB25 connector for the port.  
V.35 – The port is configured as a V.35-compatible DCE. A V.35-compatible DTE may be  
connected to the port using a DB25-to-MS34 adapter.  
X.21 – The port is configured as an X.21-compatible DCE. An X.21-compatible DTE may  
be connected to the port using a DB25-to-DB15 adapter.  
3-36  
December 2002  
9000-A2-GB31-00  
 
       
3. Configuration Options  
Table 3-16. EIA-530-A/X.21/V.35 Data Port Physical Interface Options (2 of 3)  
Transmit Clock Source  
Possible Settings: Internal, External  
Default Setting: Internal  
Determines whether the DTE’s transmitted data is clocked into the FrameSaver unit by its  
internal transmit clock or by the external clock provided by the DTE.  
NOTE: Changing settings for this configuration option causes the FrameSaver unit to  
abort any physical port tests, including any DTE-initiated loopback tests.  
Internal – The FrameSaver unit uses the interchange circuit DB (ITU 114) – Transmit  
Signal Element Timing (TXC) (DCE source) for timing the incoming data.  
External – The DTE provides the clock for the transmitted data, and the FrameSaver unit  
uses the interchange circuit DA (ITU 113) – Transmit Signal Element Timing (XTXC)  
(DTE source) for timing the incoming data.  
Invert Transmit Clock  
Possible Settings: Auto, Enable, Disable  
Default Setting: Auto  
Determines whether the clock supplied by the FrameSaver unit on interchange circuit DB  
(ITU 114) – Transmit Signal Element Timing (DCE Source) TXC is phase inverted with  
respect to the clock used to time the incoming Transmitted Data (TD).  
Auto – The port will check the clock supplied by the DCE on TXC on this port. If  
necessary, the port will automatically phase invert the clock with respect to the transmitted  
data.  
Enable – Phase inverts the TXC clock. Use this setting when long cable lengths between  
the FrameSaver unit and the DTE are causing data errors.  
Disable – Does not phase invert the TXC clock.  
Monitor DTR  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Specifies whether the state of the DTE Ready (DTR) circuit on the user data port will be  
used to determine when valid data communication is possible with the DTE. When the  
DTR off condition is detected, an alarm is generated, LMI is declared down, and no further  
transfer of frame relay data can occur on this interface.  
Enable – Interchange circuit CD (ITU 108/1/2) – DTR is monitored to determine when  
valid data is sent from the DTE.  
Disable – DTR is not monitored. DTR is assumed to be asserted and data is being  
transmitted, regardless of the state of the lead.  
9000-A2-GB31-00  
December 2002  
3-37  
 
               
3. Configuration Options  
Table 3-16. EIA-530-A/X.21/V.35 Data Port Physical Interface Options (3 of 3)  
Monitor RTS  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Specifies whether the state of the Request To Send (RTS) circuits on the user data port  
will be used to determine when valid data communication is possible with the DTE. When  
the RTS off condition is detected, CTS is deasserted, LMI is declared down, and no  
further transfer of frame relay data can occur on this interface.  
Enable – Interchange circuit CA (ITU 105) – RTS is monitored to determine when valid  
data communication is possible with the DTE.  
Disable – RTS is not monitored. RTS is assumed to be asserted and data is being  
transmitted, regardless of the state of the lead.  
Port (DTE) Initiated Loopbacks (9520)  
Possible Settings: Local, Disable  
Default Setting: Disable  
Allows a local external DTE Loopback to be started or stopped via the port’s attached data  
terminal equipment using the port’s interchange lead LL (ITU 141) for V.35, or LA (ITU  
143) for HSSI.  
Local – The DTE attached to the port controls the local external DTE Loopback.  
Disable – The DTE attached to the port cannot control the local external DTE Loopback.  
HSSI Data Port Physical Interface  
FrameSaver Model 9520 has two HSSI data ports, and Model 9820-45M has one.  
Table 3-17. HSSI Data Port Physical Interface Options (1 of 3)  
Port Status  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Determines whether the data port is being used and can be configured.  
Enable – The port is active, and can be used to transmit and receive data.  
Disable – The port is not active. When the port is disabled, the following will occur:  
No alarms or traps configured for the port will be generated.  
LED for the port will be held in an Off state.  
No – The operation is canceled. (Pressing either the Esc or Ctrl-a key also acts as a  
No.)  
Yes – Port status is disabled.  
3-38  
December 2002  
9000-A2-GB31-00  
 
                 
3. Configuration Options  
Table 3-17. HSSI Data Port Physical Interface Options (2 of 3)  
Port Type (9520)  
Possible Settings: HSSI, V.35  
Default Setting: HSSI  
Specifies the port type of the data port.  
V.35 – The port is configured as a V.35-compatible DCE. A V.35-compatible DTE may be  
connected to the port using a DB25-to-MS34 adapter.  
HSSI – The port is configured as a HSSI-compatible DCE. A HSSI-compatible DTE may  
be directly connected to the DB25 connector for the port.  
Port Rate (9520)  
Possible Settings (HSSI): 7456, 11184, 17250, 25875, 44736, 51750  
Default Setting (HSSI): 51750  
Possible Settings (V.35): 512, 1025, 1537, 2050, 2562, 3074, 3587, 4099, 4611, 5124,  
5636, 6149, 6661, 7073, 7685, 8197  
Default Setting (V.35): 6149  
Selects the clock rate in kbps for the user data port.  
Transmit Clock Source (9520)  
Possible Settings: Internal, External  
Default Setting: Internal  
Determines whether the DTE’s transmitted data is clocked into the FrameSaver unit by its  
internal transmit clock or by the external clock provided by the DTE.  
NOTE: Changing settings for this configuration option causes the FrameSaver unit to  
abort any physical port tests, including any DTE-initiated loopback tests.  
Display Conditions – This option does not appear when Port Type is set to HSSI.  
Internal – The FrameSaver unit uses the interchange circuit DB (ITU 114) – Transmit  
Signal Element Timing (TXC) (DCE source) for timing the incoming data.  
External – The DTE provides the clock for the transmitted data, and the FrameSaver unit  
uses the interchange circuit DA (ITU 113) – Transmit Signal Element Timing (XTXC)  
(DTE source) for timing the incoming data.  
Invert Transmit Clock (9520)  
Possible Settings: Auto, Enable, Disable  
Default Setting: Auto  
Determines whether the clock supplied by the FrameSaver unit on interchange circuit DB  
(ITU 114) – Transmit Signal Element Timing (DCE Source) TXC is phase inverted with  
respect to the clock used to time the incoming Transmitted Data (TD).  
Display Conditions – This option does not appear when Port Type is set to HSSI.  
Auto – The port will check the clock supplied by the DCE on TXC on this port. If  
necessary, the port will automatically phase invert the clock with respect to the transmitted  
data.  
Enable – Phase inverts the TXC clock. Use this setting when long cable lengths between  
the FrameSaver unit and the DTE are causing data errors.  
Disable – Does not phase invert the TXC clock.  
9000-A2-GB31-00  
December 2002  
3-39  
 
               
3. Configuration Options  
Table 3-17. HSSI Data Port Physical Interface Options (3 of 3)  
Monitor DTR  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Specifies whether the state of the DTE Ready (DTR) circuit on the user data port will be  
used to determine when valid data communication is possible with the DTE. When the  
DTR off condition is detected, an alarm is generated, LMI is declared down, and no further  
transfer of frame relay data can occur on this interface.  
Enable – Interchange circuit CD (ITU 108/1/2) – DTR is monitored to determine when  
valid data is sent from the DTE.  
Disable – DTR is not monitored. DTR is assumed to be asserted and data is being  
transmitted, regardless of the state of the lead.  
Monitor RTS (9520)  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Specifies whether the state of the Request To Send (RTS) circuits on the user data port  
will be used to determine when valid data communication is possible with the DTE. When  
the RTS off condition is detected, CTS is deasserted, LMI is declared down, and no  
further transfer of frame relay data can occur on this interface.  
Display Conditions – This option does not appear when Port Type is set to HSSI.  
Enable – Interchange circuit CA (ITU 105) – RTS is monitored to determine when valid  
data communication is possible with the DTE.  
Disable – RTS is not monitored. RTS is assumed to be asserted and data is being  
transmitted, regardless of the state of the lead.  
Port (DTE) Initiated Loopbacks  
Possible Settings: Local, Disable  
Default Setting: Disable  
Allows a local external DTE Loopback to be started or stopped via the port’s attached data  
terminal equipment using the port’s interchange lead LL (ITU 141) for V.35 (9520 only), or  
LA (ITU 143) for HSSI.  
Local – The DTE attached to the port controls the local external DTE Loopback.  
Disable – The DTE attached to the port cannot control the local external DTE Loopback.  
3-40  
December 2002  
9000-A2-GB31-00  
 
           
3. Configuration Options  
Configuring the T3 User Port (9520-ILM)  
Select Physical to display or change the physical characteristics of the user data  
port connected to the DTE (see Table 3-18, T3 User Port Physical Interface  
Options).  
Main MenuConfigurationT3 User PortsPhysical  
Table 3-18. T3 User Port Physical Interface Options  
Line Build Out  
Possible Settings: Short, Long  
Default Setting: Short  
Specifies whether a line equalization filter is activated to simulate a longer cable.  
Short – The equalization filter is activated. Use this option for DTE cables less than 100  
feet long.  
Long – The equalization filter is not activated. Use this option for DTE cables 100 feet or  
longer.  
9000-A2-GB31-00  
December 2002  
3-41  
 
     
3. Configuration Options  
Configuring the DSX-1 Interface (9126, 9128)  
Select DSX-1 to display or change the physical configuration options when a  
DSX-1 interface is installed (see Table 3-19, DSX-1 Physical Interface Options).  
Main MenuConfigurationDSX-1  
Table 3-19. DSX-1 Physical Interface Options (1 of 2)  
Interface Status  
Possible Settings: Enable, Disable  
Default Setting:Disable  
Specifies whether the DSX-1 interface selected is available for use.  
Enable – The interface is available.  
Disable – The interface is not available for use. If there are time slots assigned to the  
DSX-1 interface when you attempt to disable it, the message This action will  
clear all DSX-1 Cross Connections. Are You Sure? Noappears. If you  
select:  
No – The operation is cancelled.  
Yes – The following occurs:  
All existing DSX-1 interface cross-connect assignments are cleared.  
Alarms or traps associated with the DSX-1 interface are not generated.  
LEDs associated with the DSX-1 interface are held in an “off’’ state.  
Line Framing Format  
Possible Settings: D4, ESF  
Default Setting: ESF  
Specifies the framing format for transmitted and received signals on the DSX-1 interface.  
D4 – Uses D4 framing format.  
ESF – Uses Extended Superframe (ESF) framing format.  
Line Coding Format  
Possible Settings: AMI, B8ZS  
Default Setting: B8ZS  
Specifies the line coding format for the DSX-1 interface.  
AMI – Uses Alternate Mark Inversion (AMI) line coding format.  
B8ZS – Uses Bipolar 8 Zero Substitution (B8ZS) line coding format.  
3-42  
December 2002  
9000-A2-GB31-00  
 
             
3. Configuration Options  
Table 3-19. DSX-1 Physical Interface Options (2 of 2)  
Line Equalization  
Possible Settings: 0–133, 133–266, 266–399, 399–533, 533–655  
Default Setting: 0–133  
Permits a standard DSX signal to be delivered over a distance of up to 655 feet.  
0–133 – Equalization on the DSX-1 side allows up to 133 feet of cable between the  
FrameSaver unit and the DTE.  
133–266 – Equalization on the DSX-1 side allows up to 266 feet of cable between the  
FrameSaver unit and the DTE.  
266–399 – Equalization on the DSX-1 side allows up to 399 feet of cable between the  
FrameSaver unit and the DTE.  
399–533 – Equalization on the DSX-1 side allows up to 533 feet of cable between the  
FrameSaver unit and the DTE.  
533–655 – Equalization on the DSX-1 side allows up to 655 feet of cable between the  
FrameSaver unit and the DTE.  
Send All Ones on DSX-1 Failure  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Determines whether action is taken when a valid signal cannot be recovered for the  
DSX-1 (LOS, continuous OOF, or AIS).  
Enable – Sends all ones on the DS0 channels allocated to the DSX-1 interface in the  
event of an LOS, AIS, or continuous OOS condition on the DSX-1 interface.  
Disable – No action is taken when a signal fails on the DSX-1 interface. The data  
received is passed through the network interface channels unchanged.  
9000-A2-GB31-00  
December 2002  
3-43  
 
   
3. Configuration Options  
Configuring the ISDN DBM Interface (9126, 9128, 9626)  
For models with ISDN backup capability, select Physical from the ISDN menu to  
configure the physical characteristics for DBM Interface.  
Main MenuConfigurationISDNPhysical  
When configuring a BRI DBM, refer to Table 3-20, ISDN BRI DBM Physical  
When configuring a PRI DBM, refer to Table 3-21, ISDN PRI DBM Physical  
Table 3-20. ISDN BRI DBM Physical Interface Options (9126, 9626)  
Interface Status  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Determines whether the ISDN interface is available for use.  
Enable – The ISDN interface is enabled.  
Disable – The ISDN interface cannot be configured, nor can it transmit or receive data.  
No PVC connections or frame relay DLCIs will be deleted. Disabling the ISDN interface  
results in the following:  
All currently connected ISDN calls are terminated.  
Alarms or traps associated with this interface are not generated or displayed.  
Service Profile ID (SPID) 1 or 2  
Possible Settings: 3 – 20 digits  
Default Setting: Clear  
Specifies the SPID number assigned by the ISDN service provider for Bearer channel 1  
(B1) and Bearer channel 2 (B2). SPID numbers are used by the switch to identify which  
ISDN services the DBM can access. All blanks is a valid setting.  
3 – 20 digits You can enter a SPID number, or you can leave blanks. If a nondigit/  
numeric is entered, an Invalid Character (x)message appears at the bottom of  
the screen. If fewer than three digits/numerics are entered, an Invalid – SPID must  
be at least 3 digitsmessage appears at the bottom of the screen.  
Clear – Clears the SPID field so it can be reentered.  
Local Phone Number 1 or 2  
Possible Settings: 10 digits  
Default Setting: Clear  
Provides the telephone number associated with Bearer channel 1 (B1) and 2 (B2). All  
blanks is a valid setting.  
10 digits – Enter the telephone number, up to 10 digits. If a nondigit/numeric is entered,  
an Invalid Character (x)message appears at the bottom of the screen.  
Clear – Clears the phone number field so it can be reentered.  
3-44  
December 2002  
9000-A2-GB31-00  
 
                     
3. Configuration Options  
Refer to the Table 3-21 when configuring a PRI DBM.  
Table 3-21. ISDN PRI DBM Physical Interface Options (9128) (1 of 3)  
Interface Status  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Determines whether the ISDN interface is available for use.  
Enable – The ISDN interface is enabled.  
Disable – The ISDN interface cannot be configured, nor can it transmit or receive data.  
No PVC connections or frame relay DLCIs will be deleted. Disabling the ISDN interface  
results in the following:  
All currently connected ISDN calls are terminated.  
Alarms or traps associated with this interface are not generated or displayed.  
LEDs associated with this interface are held in an “off" state. Specifically, the  
DSX/PRI LEDs are held off if they represent the PRI status.  
Switch Type  
Possible Settings: NI-2, ATT_4ESS, ATT_5ESS  
Default Setting: NI-2  
Specifies type of ISDN switch provided by the server.  
NI-2 – The DBM will communicate with a service provider supporting the National ISDN-2  
switching standard.  
ATT_4ESS – The DBM will communicate with a service provider supporting the  
ATT 4ESS switching standard.  
ATT_5ESS – The DBM will communicate with a service provider supporting the  
ATT 5ESS switching standard.  
Local Phone Number  
Possible Settings: 10 digits  
Default Setting: Clear  
Provides the telephone number associated with all Bearer channels. All blanks is a valid  
setting.  
10 digits – Where you enter the telephone number, up to 10 digits. If a nondigit/numeric is  
entered, an Invalid Character (x)message appears at the bottom of the screen.  
Clear – Clears the phone number field so it can be reentered.  
Line Framing Format  
Possible Settings: D4, ESF  
Default Setting: ESF  
Specifies the framing format for transmitted and received signals on the ISDN interface.  
D4 – Uses D4 framing format.  
NOTE: This setting is not recommended by network carriers. False yellow alarms may  
occur after traffic has been running and the channel returns to idle, or when there is  
light traffic when other settings are selected. ESF format does not create this problem.  
ESF – Uses Extended Superframe framing format.  
9000-A2-GB31-00  
December 2002  
3-45  
 
         
3. Configuration Options  
Table 3-21. ISDN PRI DBM Physical Interface Options (9128) (2 of 3)  
Line Build Out (LBO)  
Possible Settings: 0.0, –7.5, –15, –22.5  
Default Setting: 0.0  
Specifies the line build out for the signal transmitted to the ISDN.  
0.0, –7.5, –15, –22.5 – Specifies line build out in dB.  
Network Initiated LLB  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Allows the initiation and termination of the line loopback (LLB) to be controlled by the  
receipt of LLB-Actuate and LLB-Release commands from the ISDN.  
Enable – LLB is controlled by LLB-Actuate and LLB-Release commands. Receiving a  
LLB-Actuate command causes the system to enter a line loopback (provided an LLB can  
be performed in the system’s current state). Receiving an LLB-Release command  
terminates the LLB.  
Disable – The system ignores the LLB-Actuate and LLB-Release commands.  
NOTE: When disabled, the system is not in compliance with ANSI T1.403 or  
AT&T TR 62411.  
Network Initiated PLB  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Allows the initiation and termination of the payload loopback (PLB) to be controlled by the  
receipt of PLB-Actuate and PLB-Release commands from the ISDN.  
Display Conditions – This option only appears when Line Framing Format is set to  
ESF.  
Enable – PLB is controlled by PLB-Actuate and PLB-Release commands. Receiving a  
PLB-Actuate command causes the system to enter a payload loopback (provided a PLB  
can be performed in the system’s current state). Receiving a PLB-Release command  
terminates the PLB.  
Disable – The system ignores the PLB-Actuate and PLB-Release commands.  
NOTE: When disabled, the unit is not in compliance with ANSI T1.403 or  
AT&T TR 54016.  
ANSI Performance Report Messages  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Specifies whether ANSI T1.403 compliance performance report messages (PRMs) are  
generated and sent to the ISDN over the ESF facility data link every second.  
Display Conditions – This option only appears when Line Framing Format is set to  
ESF.  
Enable – Generates and sends PRMs.  
Disable – Does not generate and send PRMs.  
3-46  
December 2002  
9000-A2-GB31-00  
 
       
3. Configuration Options  
Table 3-21. ISDN PRI DBM Physical Interface Options (9128) (3 of 3)  
Excessive Error Rate Threshold  
Possible Settings: 10E-4, 10E-5, 10E-6, 10E-7, 10E-8, 10E-9  
Default Setting: 10E-4  
Sets the error rate threshold that determines when an EER condition is declared. The  
excessive error rate is determined by the ratio of the number of CRC6 errors to the total  
number of bits received over a set period of time.  
Display Conditions – This option only appears when Line Framing Format is set to  
ESF.  
10E-4 – Declares an EER if more than 1,535 CRC6 errors are detected in a 10 second  
period. Clears when fewer than 1,536 CRC6 errors are detected within the same time  
period.  
10E-5 – Declares an EER if more than 921 CRC6 errors are detected in a 60 second  
period or a 10- 4 condition occurs. Clears when fewer than 922 CRC6 errors are detected  
within the same time period.  
10E-6 – Declares an EER if more than 92 CRC6 errors are detected in a 60 second period  
or a 10-5 or 10- 4 condition occurs. Clears when fewer than 93 CRC6 errors are detected  
within the same time period.  
10E-7 – Declares an EER if more than 9 CRC6 errors are detected in a 60 second period  
or a 10-6, or 10- 5, or 10- 4 condition occurs. Clears when fewer than 10 CRC6 errors are  
detected within the same time period.  
10E-8 – Declares an EER if more than 41 CRC6 errors are detected in three 15 minute  
intervals or a 10-7, 10-6, 10- 5, 10- 4 condition occurs. Clears when fewer than 42 CRC6  
errors are detected within the same time period.  
10E-9 – Declares an EER if more than 4 CRC6 errors are detected in three 15 minute  
intervals or a 10- 8, 10-7, 10- 6, 10- 5, or 10- 4 condition occurs. Clears when fewer than  
5 CRC6 errors are detected within the same time period.  
Circuit Identifier  
Possible Settings: ASCII Text Entry, Clear  
Default Setting: blank  
Identifies the transmission vendor’s circuit information to facilitate troubleshooting.  
ASCII Text Entry – Assigns a name to identify the circuit (maximum 255 characters).  
Clear – Removes the circuit identifier information.  
9000-A2-GB31-00  
December 2002  
3-47  
 
   
3. Configuration Options  
Setting Up ISDN Link Profiles (9126, 9128, 9626)  
For models with ISDN backup capability, select ISDN Link Profiles from the ISDN  
menu to set up the ISDN Link Profiles (see Table 3-22, ISDN Link Profile Options).  
Main MenuConfigurationISDNISDN Link Profiles  
Table 3-22. ISDN Link Profile Options (1 of 3)  
Link Name  
Possible Settings: ASCII Text Entry, HQ_Site  
Default Setting: HQ_Site for first link; blank for all others  
Assigns the name to the ISDN link profile. It is generally the backup destination for a  
frame relay link. Each profile must have a unique link name. If the link name field is blank,  
the link profile will be deleted. Use ASCII text, 8 characters maximum.  
ASCII Text Entry – Assigns a name to identify the ISDN link (maximum 255 characters).  
NOTE: To prevent confusion, do not use the following link names: Network, Net1-FR1,  
Port-1, or Port-2. These names will be treated as nonunique and the Link Name Not  
Uniquemessage appears and you must enter another name.  
HQ_Site – The link name configured in the remote site unit (originating a backup call) for  
the central site unit (answering a backup call). One link has a default value of HQ_Site to  
allow for Automatic Backup Configuration.  
Link Status  
Possible Settings: Auto, Disable  
Default Setting: Auto  
Determines whether the ISDN frame relay link is in or out of service.  
Auto – The link is configured to be in service when needed. Packets will be transmitted  
and received on the interface, and the LMI for a PVC connection will become active when  
the link is required. If this profile is configured as the alternate link and the primary link or  
DLCI fails, the unit dials the Outbound Phone Number, or the Alternate Outbound Phone  
Number if the first call was unsuccessful. The unit also answers calls from Inbound Call  
IDs associated with this link. This link profile becomes active when:  
This profile is configured as the alternate link and there is a failure of a primary link  
or DLCI.  
Source or Primary Destination DLCIs are configured on this link.  
When the primary link recovers, the call is automatically disconnected.  
Disable – The frame relay link is out of service. No data will be transmitted or received on  
the interface. If there is are any active calls when disabled, the calls are ended and no  
calls will be answered or originated using this profile.  
3-48  
December 2002  
9000-A2-GB31-00  
 
                 
3. Configuration Options  
Table 3-22. ISDN Link Profile Options (2 of 3)  
Outbound Phone Number  
Possible Settings: 0 – 9, *, #, space, _, , (, or )  
Default Setting: none  
Specifies the primary phone number to call (the ISDN Called Party Identifier) for the Link  
Profile. Up to 18 valid characters can be entered. Each Outbound Phone Number must be  
unique. If not, the Outbound Phone Number is Not Uniquemessage appears and  
you must enter another phone number.  
NOTE: For every originating (outbound) phone number entered, an answering  
(inbound) phone number must be entered at the far end, and vice versa.  
Currently active calls are not effected when this number is changed.  
Inbound Calling ID 1 or 2  
Possible Settings: 0 9  
Default Setting: none  
Specifies the local phone number of a remote device from which that the unit will accept  
calls (the ISDN Calling Party Identifier). Up to 18 digits can be entered. Each Inbound  
Calling ID must be unique. If not, the Inbound Calling ID n is Not Unique  
message appears and you must enter another phone number.  
For remote devices with a PRI DBM, only one Inbound Calling ID is required. Inbound  
Calling ID 2 is provided to identify incoming calls from a second phone number assigned  
to a remote device with a BRI DBM.  
NOTES:  
– Inbound Calling ID 2 is only useful when multiple local phone numbers are  
programmed at the originating site (e.g., a 2B+D BRI location).  
– For every originating (outbound) phone number entered, an answering (inbound)  
phone number must be entered at the far end, and vice versa.  
Currently active calls are not effected when this number is changed.  
0 – 9 – Specifies the numbers in the remote device’s local phone number.  
Maximum Link Rate (Kbps)  
Possible Settings:  
For a BRI DBM: 64, 128  
For a PRI DBM: 64 1472  
Default Setting: 64  
Specifies the maximum rate that will be attempted for the frame relay link when it is  
activated. The actual rate achieved on the link depends upon the number of successful  
calls placed or answered, and the negotiated rate on each call.  
NOTE: This option takes effect as soon as a change is saved. If the rate is increased,  
additional calls will be placed. If the rate is decreased, calls will be dropped. For extra  
calls to be successful, the Maximum Link Rate must be increased at the originating  
device before it is increased at the answering device.  
64 – An individual frame relay link is formed and a single call is placed using a B-channel  
when the link is activated.  
128 . . . 1472 – A constituent link is configured for each multiple of 64 Kbps in the  
specified bandwidth. This bundle of constituent links will function as a single frame relay  
multilink. When the multilink aggregate link is activated, calls will be placed or answered  
on as many constituent links as possible based upon available B-channels.  
9000-A2-GB31-00  
December 2002  
3-49  
 
       
3. Configuration Options  
Table 3-22. ISDN Link Profile Options (3 of 3)  
Caller Identification Method  
Possible Settings: Caller ID, Proprietary  
Default Setting: Caller ID  
Specifies the method used to identify callers.  
NOTE: The Caller Identification Method setting must be the same at both ends of the  
circuit.  
Caller ID – Incoming calls will only be answered and the frame relay link on this Link  
Profile will only be activated when the Caller ID received from the switch matches one of  
the configured Inbound Calling IDs.  
Proprietary – Incoming calls will always be answered, even when no Caller ID is provided  
by the switch, provided the following conditions are met:  
Link Status is set to Auto (the default).  
At least one ISDN Link Profile is enabled.  
When using the Proprietary method, the unit queries the originating unit for its Local  
Phone Number. If the returned phone number matches one of the configured Inbound  
Calling IDs, the call is accepted. If the queried unit does not respond with its phone  
number within five seconds, the unit drops the call.  
Alternate Outbound Phone Number  
Possible Settings: 0 – 9, *, #, space, _, , (, or )  
Default Setting: none  
Specifies an alternate phone number to call (the ISDN Called Party Identifier) when a call  
using the primary Outbound Phone Number was unsuccessful. Up to 18 valid characters  
can be entered. Each Outbound Phone Number must be unique. If not, the Alt  
Outbound Phone Number is Not Uniquemessage appears and you must enter  
another phone number.  
NOTE: For every originating (alternate outbound) phone number entered, an  
answering (inbound) phone number must be entered at the far end, and vice versa.  
Currently active calls are not effected when this number is changed.  
Assigning Time Slots/Cross Connections  
The Time Slot Assignment/Cross Connect feature provides an easy method of  
assigning time slots for frame relay data and creating cross-connections to the  
synchronous data interface. The system allows you to assign DS0s on the T1  
network interface and between the user data port and network interface in order to  
share the T1 network.  
You can also clear cross-connection assignments for the system, or for a selected  
slot or interface.  
NOTE:  
Although it is not required, it is suggested that you progress through each  
screen in order, from top to bottom.  
3-50  
December 2002  
9000-A2-GB31-00  
 
                   
3. Configuration Options  
Assigning Time Slots to the Network Interface  
Before assigning network time slots for use by frame relay traffic, configure the  
Network physical and Frame Relay options (if needed), then allow Time Slot  
Discovery to autodetect and assign the appropriate time slots to frame relay.  
If there are multiple Frame Relay data links on the network interface, or if Time  
Slot Discovery is not currently active, you can manually assign time slots on the  
network interface for frame relay traffic using the Frame Relay Network  
Assignments screen. This screen is read-only when Time Slot Discovery is set to  
Enable for the network interface.  
Link Layer Network Time Slot Assignment Screen Example  
main/config/tslot_assign/frame_relay  
Device Name: Node A  
9128-II  
11/05/2002 13:03  
LINK LAYER NETWORK 1 ASSIGNMENT  
Time Slot Discovery: Disable  
N01  
N02  
N03  
N04  
N05  
N06  
N07  
N08  
Available Available Available Available Available Available Available Available  
N09  
N10  
N11  
N12  
N13  
N14  
N15  
N16  
Available Available FrameRly1 FrameRly1 FrameRly1 FrameRly1 FrameRly1 FrameRly1  
N17  
N18  
N19  
N20  
N21  
N22  
N23  
N24  
FrameRly1 FrameRly1 FrameRly1 FrameRly1 FrameRly1 FrameRly1 FrameRly1 FrameRly1  
--------------------------------------------------------------------------------  
Ctrl-a to access these functions, ESC for previous menu  
MainMenu  
Exit  
Save  
PgDn  
PgUp  
ClearAll  
DSXAssign  
Value  
Meaning  
Time Slot  
Discovery  
Specifies whether the time slots used for frame relay traffic should  
be discovered from the network interface upon detection of an LMI  
failure. This option allows additional time slots to be added without  
manually reconfiguring the device.  
Ntt  
This field represents time slot tt of the selected network interface.  
Assigned  
The time slot is already assigned to something other than frame  
relay, so it is unavailable. Assigned time slots cannot be modified  
from this screen.  
Available  
FrameRly1  
FrameRly2  
PPP  
The time slot is currently unassigned.  
The time slot is assigned to frame relay service, link 1.  
The time slot is assigned to frame relay service, link 2.  
The time slot is assigned to the network interface.  
9000-A2-GB31-00  
December 2002  
3-51  
 
     
3. Configuration Options  
For easy movement between screens, select the DSXAssign function key to go  
directly to the DSX-1 to Network Assignments screen.  
Time Slot Assignment Rule:  
Valid network time slots are either Available or contain a Frame Relay Link 1  
assignment.  
Procedure  
1. Follow this menu selection sequence:  
Main MenuConfigurationTime Slot Assignment →  
Link Layer Network Assignments  
The Frame Relay Network Assignments screen appears. This screen contains  
a matrix of the current assignment status of all time slots on the network  
interface.  
2. Enable or disable Time Slot Discovery.  
— When enabled, the unit examines all time slots not cross-connected to  
other ports to determine which time slots are being used by the network  
for frame relay traffic. These time slots are set to FrameRly1. This is the  
factory default.  
— When disabled, time slot assignments must be manually configured.  
3. If Time Slot Discovery is disabled, assign network time slots for use by frame  
relay service, link 1, by typing FrameRly1 in the selected Network field.  
4. Repeat Step 3 until all desired time slots are assigned.  
5. Save the configuration.  
Assigning DSX-1 Time Slots to the Network Interface  
DSX-1 time slots are assigned by channel allocation, where you specify individual  
time slots. The DSX-1 interface must be enabled to assign DSX-1 time slots to the  
Value  
Ntt  
Meaning  
It represents time slot tt of the selected network interface.  
Assigned  
The time slot is already assigned to something other than a DSX-1  
time slot, so it is unavailable. Assigned time slots cannot be modified  
from this screen.  
Available  
The time slot is currently unassigned.  
DSX-1/tt  
Slot tt of the DSX-1 interface is assigned to the network interface  
time slot identified right above it (Ntt).  
3-52  
December 2002  
9000-A2-GB31-00  
 
     
3. Configuration Options  
DSX-1 to Network Time Slot Assignment Screen Example (Page 1)  
main/config/tslot_assign/dsx  
Device Name: Node A  
9128-II  
5/26/1999 23:32  
DSX-1 TO NETWORK 1 ASSIGNMENTS  
Page 1 of 2  
N01  
N02  
N03  
N04  
N05  
N06  
N07  
N08  
DSX-1/01 DSX-1/02 DSX-1/03 DSX-1/04 Assigned Assigned Assigned Assigned  
N09  
N10  
N11  
N12  
N13  
N14  
N15  
N16  
DSX-1/09 DSX-1/01 Available Available Available Available Available Available  
N17  
N18  
N19  
N20  
N21  
N22  
N23  
N24  
Available Available Available Available Available Available Available Available  
--------------------------------------------------------------------------------  
Ctrl-a to access these functions, ESC for previous menu  
Save PgDn PgUp ClearAll  
MainMenu  
FrAssign  
Exit  
Page 2 of 2 is for defining signaling assignments and trunk conditioning for each  
DSX-1 interface time slot. See DSX-1 Signaling Assignments and Trunk  
Conditioning (Page 2) on page 3-54 for an example of this screen.  
For easy movement between screens, select the FrAssign function key to go  
directly to the Frame Relay Network Assignments screen.  
Time Slot Assignment Rules:  
n
n
n
Valid Network time slots are either Available or contain a DSX-1 time slot  
assignment.  
Valid DSX-1 time slots are those that are unassigned, including the currently  
assigned time slot.  
Order of display is as follows:  
Available is the first selection.  
— Then, from the lowest DSX-1 interface to the highest DSX-1 interface.  
— Then the lowest available time slot number to the highest available time  
slot number.  
For example, if the cursor is on a field with the Available value under  
assigned time slot Ntt, pressing the Spacebar causes this field’s values to  
cycle through all valid DSX-1 time slots, starting with Ds-p/yy, assuming it is  
unassigned. If Ds-p/tt is already assigned, the next valid time slot in the order  
described above is displayed.  
9000-A2-GB31-00  
December 2002  
3-53  
 
3. Configuration Options  
Procedure  
1. Follow this menu selection sequence:  
ConfigurationTime Slot AssignmentDSX-to-Network Assignments  
The DSX-1 to Network Assignments screen appears. This screen contains a  
matrix of the current cross-connect status of all time slots on the network  
interface.  
2. Move the cursor to the next time slot that can be edited (underlined). Use the  
spacebar or type in the desired time slot to display its time slot assignment.  
3. Repeat Step 2 until all desired time slots are assigned.  
4. Save the configuration.  
DSX-1 Signaling Assignments and Trunk Conditioning (Page 2)  
The second page of the DSX-1 to Network Assignments screen allows you to  
define the signaling assignments and trunk conditioning for each time slot on the  
DSX-1 interface. You can specify whether robbed bit signaling information is being  
passed within a given DS0, and the value of the signaling bits that will be  
transmitted for that DS0 to the other cross-connected T1 network interface if a  
Carrier Group Alarm (CGA) occurs on a T1 network interface.  
DSX-1 to Network Time Slot Assignment Screen Example (Page 2)  
main/config/tslot_assign/dsx  
Device Name: Node A  
9128-II  
5/26/2000 23:32  
DSX-1 TO NETWORK 1 ASSIGNMENTS  
SIGNALING AND TRUNK CONDITIONING  
Page 2 of 2  
Network 1 Side  
DSX-1 Side  
Network 1 Side  
DSX-1 Side  
Net1/01 E&M-busy - DSX-1/01 E&M-busy  
Net1/03 E&M-busy - DSX-1/03 E&M-busy  
Net1/02 E&M-busy  
Net1/04 E&M-busy  
Net1/10 None  
- DSX-1/01 E&M-busy  
- DSX-1/04 E&M-busy  
- DSX-1/10 None  
Net1/09 None  
- DSX-1/09 None  
--------------------------------------------------------------------------------  
Ctrl-a to access these functions, ESC for previous menu MainMenu Exit  
Save PgDn PgUp ClearAll VocAssign FrAssign  
For easy movement between screens, select the FrAssign function key to go  
directly to the Frame Relay Network Assignments screen or the DSXAssign  
function key to go to the DSX-1 to Network Assignments screen.  
3-54  
December 2002  
9000-A2-GB31-00  
 
       
3. Configuration Options  
Only those DSX-1-to-Network assignments from page 1 are displayed on this  
page, from left to right and top to bottom in ascending order, by network and time  
slot.  
When a CGA condition (LOS, OOF, or AIS) is declared for a T1 interface, the  
signaling bits being transmitted to the other T1 interface for the DS0 are forced to  
idle for two seconds (except for user-defined patterns which are transmitted  
immediately). This drops any call in progress. The signaling bits are then forced to  
the selected state (Busy or Idle), and remain in this state until the CGA condition  
clears. At this point, the received signaling bits from the T1 interface which  
formerly had the CGA condition are passed through to the other T1 interface.  
NOTE:  
Trunk conditioning will only occur on DS0s that are cross-connected to  
another T1 interface. All other DS0s remain unaffected by trunk conditioning.  
Enter one of the values shown in Table 3-23, Signaling and Trunk Conditioning  
Values, in each of the fields on both the Network side and the DSX-1 side.  
Although you can choose any value for the DSX-1 side, the default value  
displayed is based on a typical setting that would be used with the corresponding  
Network side value. Typical pairs of values are shown in the table below. If you  
change the Network side value, the DSX side value is changed to the  
corresponding default value.  
Table 3-23. Signaling and Trunk Conditioning Values (1 of 3)  
Network Side Meanings  
DSX-1 Side  
None  
No signaling used on this DS0. Use this setting if  
None  
there is no voice signaling information being passed  
on this DS0 (clear channel).  
RBS (default)  
Robbed Bit Signaling is used on this DS0, but no  
trunk conditioning. Signaling bits will be passed to the  
T1 interface to which this DS0 is cross-connected  
when this T1 interface is not in CGA, but the signaling  
bits will be all ones when CGA is present.  
RBS  
The following values configure the cross-connect for RBS, as well as perform the  
trunk conditioning. Although ABCD signaling bits for each setting are described,  
only AB bits are transmitted when the cross-connected T1 network interface is  
using D4 framing.  
9000-A2-GB31-00  
December 2002  
3-55  
 
 
3. Configuration Options  
Table 3-23. Signaling and Trunk Conditioning Values (2 of 3)  
Network Side Meanings  
DSX-1 Side  
E&M-idle  
The signaling bits transmitted to the cross-connected E&M idle  
T1 interface during a CGA represent the idle state for  
an E&M interface (ABCD = 0000).  
E&M-busy  
FXOg-idle  
FXOg-busy  
FXOl-idle  
The signaling bits transmitted to the cross-connected E&M busy  
T1 interface during a CGA represent the busy state  
for an E&M interface (ABCD = 1111).  
The signaling bits transmitted to the cross-connected FXSg-idle  
T1 interface during a CGA represent the idle state for  
an FXO Ground-Start interface (ABCD = 1111).  
The signaling bits transmitted to the cross-connected FXSg-busy  
T1 interface during a CGA represent the busy state  
for an FXO Ground-Start interface (ABCD = 0101).  
The signaling bits transmitted to the cross-connected FXSl-idle  
T1 interface during a CGA represent the idle state for  
an FXO Loop-Start interface (ABCD = 0101).  
FXOl-busy  
FXSg-idle  
FXSg-busy  
FXSl-idle  
The signaling bits transmitted to the cross-connected FXSl-busy  
T1 interface during a CGA represent the busy state  
for an FXO Loop-Start interface (ABCD = 0101).  
The signaling bits transmitted to the cross-connected FXOg-idle  
T1 interface during a CGA represent the idle state for  
an FXS Ground-Start interface (ABCD = 0101).  
The signaling bits transmitted to the cross-connected FXOg-busy  
T1 interface during a CGA represent the busy state  
for an FXS Ground-Start interface (ABCD = 1111).  
The signaling bits transmitted to the cross-connected FXOl-idle  
T1 interface during a CGA represent the idle state for  
an FXS Loop-Start interface (ABCD = 0101).  
FXSl-busy  
FXOD-idle  
FXOD-busy  
FXSD-idle  
FXSD-busy  
The signaling bits transmitted to the cross-connected FXOl-busy  
T1 interface during a CGA represent the busy state  
for an FXS Loop-Start interface (ABCD = 1111).  
The signaling bits transmitted to the cross-connected FXSD-idle  
T1 interface during a CGA represent the idle state for  
an FXODN interface (ABCD = 0000).  
The signaling bits transmitted to the cross-connected FXSD-busy  
T1 interface during a CGA represent the busy state  
for an FXODN interface (ABCD = 1111).  
The signaling bits transmitted to the cross-connected FXOD-idle  
T1 interface during a CGA represent the idle state for  
an FXSDN interface (ABCD = 0000).  
The signaling bits transmitted to the cross-connected FXOD-busy  
T1 interface during a CGA represent the busy state  
for an FXSDN interface (ABCD = 1111).  
3-56  
December 2002  
9000-A2-GB31-00  
 
3. Configuration Options  
Table 3-23. Signaling and Trunk Conditioning Values (3 of 3)  
Network Side Meanings  
DSX-1 Side  
PLAR3idle  
PLAR3busy  
PLAR4idle  
PLAR4busy  
DPO-idle  
The signaling bits transmitted to the cross-connected PLAR3idle  
T1 interface during a CGA represent the idle state for  
a PLAR D3 interface (ABCD = 0000).  
The signaling bits transmitted to the cross-connected PLAR3busy  
T1 interface during a CGA represent the busy state  
for an PLAR D3 interface (ABCD = 1111).  
The signaling bits transmitted to the cross-connected PLAR4idle  
T1 interface during a CGA represent the idle state for  
a PLAR D4 interface (ABCD = 1111).  
The signaling bits transmitted to the cross-connected PLAR4busy  
T1 interface during a CGA represent the busy state  
for an PLAR D4 interface (ABCD = 0000).  
The signaling bits transmitted to the cross-connected DPT-idle  
T1 interface during a CGA represent the idle state for  
a DPO interface (ABCD = 0000).  
DPO-busy  
DPT-idle  
The signaling bits transmitted to the cross-connected DPT-busy  
T1 interface during a CGA represent the busy state  
for a DPO interface (ABCD = 1111).  
The signaling bits transmitted to the cross-connected DPO-idle  
T1 interface during a CGA represent the idle state for  
a DPT interface (ABCD = 0000).  
DPT-busy  
USER-xxxx  
The signaling bits transmitted to the cross-connected DPO-busy  
T1 interface during a CGA represent the busy state  
for a DPT interface (ABCD = 1111).  
The signaling bits transmitted to the cross-connected USER-xxxx*  
T1 interface during a CGA represent a user-defined  
pattern of ABCD = xxxx.  
* xxxx is the same value on both the Network and the DSX-1 sides.  
9000-A2-GB31-00  
December 2002  
3-57  
 
3. Configuration Options  
Assigning a Synchronous Data Port to Network or DSX-1 Time Slots  
For a FrameSaver SLV unit with two data ports, another assignment screen is  
available. Use the Sync Data Port Assignment screen to view the status of:  
n
n
All DS0 assignments on the Network interface  
All DS0 assignments on the DSX-1 interface  
Then, you can a assign synchronous data port to:  
n
n
Network interface time slots  
DSX-1 interface time slots  
Synchronous Data Port Assignment Screen Example  
main/config/tslot_assign/sync_data/net  
Device Name: Node A  
9128-II  
5/26/2000 23:32  
SYNC DATA PORT ASSIGNMENT  
Assign To: Net1  
N01  
N02  
N03  
N04  
N05  
N06  
N07  
N08  
Assigned Assigned Assigned Assigned Assigned Port-2  
Port-1  
Assigned  
N09  
N10  
N11  
N12  
N13  
N14  
N15  
N16  
Assigned Assigned Assigned Assigned Assigned Port-2  
Port-1  
Available  
N17  
N18  
N19  
N20  
N21  
N22  
N23  
N24  
Available Available Available Available Available Available Available Available  
--------------------------------------------------------------------------------  
Ctrl-a to access these functions, ESC for previous menu  
MainMenu  
Exit  
Save  
ClearAll  
DSXAssign  
FrAssign  
Value  
Meaning  
Assign To  
Specifies either Net1 (network) or DSX1-1 (DSX-1) time slots.  
Ntt  
This field represents time slot tt of the network interface.  
Dtt  
This field represents time slot tt of the DSX-1 interface.  
Assigned  
The time slot is already assigned to a network or DSX-1 time slot.  
Assigned time slots cannot be modified from this screen.  
Available  
Port-2  
The time slot is currently unassigned.  
For a FrameSaver SLV unit with two data ports, synchronous data  
Port-2 is assigned to the time slot.  
3-58  
December 2002  
9000-A2-GB31-00  
 
           
3. Configuration Options  
For easy movement between screens, select the FrAssign function key to go  
directly to the Frame Relay Network Assignments screen or the DSXAssign  
function key to go to the DSX-1 to Network Assignments screen.  
Time Slot Assignment Rules:  
n
To assign a synchronous data port to network or DSX-1 time slots, Port-2’s  
Port Use option must be set for Synchronous Data (see Table 3-15, V.35 Data  
n
If the DSX-1 interface is disabled, only Net1 is available for synchronous data  
port assignment (see the Interface Status option in Table 3-19, DSX-1  
Procedure  
1. Select one of the following menu selection sequences:  
Main MenuConfigurationTime Slot Assignment →  
Sync Data Port Assignments or  
Main MenuEasy InstallTime Slot Assignment Screen  
2. Select an interface in the Assign To field. A matrix of the current cross-connect  
status of all time slots on the selected interface appears.  
3. Move the cursor to the next time slot that can be edited (underlined). Use the  
spacebar or type in the desired time slot to display its time slot assignment.  
4. Repeat Step 3 until the synchronous data port is assigned to all desired time  
slots.  
5. Save the configuration.  
Clearing Assignments  
Clearing assignments sets all time slots to Unassgn (unassigned).  
Main MenuConfigurationTime Slot AssignmentClear Assignments  
9000-A2-GB31-00  
December 2002  
3-59  
 
   
3. Configuration Options  
Configuring Frame Relay for an Interface  
Select Frame Relay from the interface’s menu to display or change the Frame  
Relay options for an individual interface (see Table 3-25, Interface PPP Options).  
Frame Relay is not an option on the Network menu unless Service Type is Frame  
Relay.  
Main MenuConfiguration[Network/Data/T3 User Ports] Frame Relay  
See Configuring PPP for an Interface on page 3-63, for additional information.  
Table 3-24. Interface Frame Relay Options (1 of 3)  
LMI Protocol  
Possible Settings: Initialize_From_Net1FR1,  
Initialize_From_Interface,  
Auto_On_LMI_Fail,  
Standard,  
Annex-A,  
Annex-D  
Default Setting:  
For a user data port link: Initialize_From_Interface  
For a network link: Auto_On_LMI_Fail  
Specifies either the LMI protocol supported on the frame relay interface or the discovery  
source for the LMI protocol.  
Initialize_From_Net1FR1 – The LMI type supported on this frame relay link will be  
configured to match the LMI protocol initially discovered on the primary Network frame  
relay link (Net1FR1). LMI Protocol is set to None internally, but once a protocol has  
become active or is set on the primary Network link, the protocol will be set to the same  
value on this link (Standard, Annex-A or Annex-D). The protocol will not be updated based  
on changes to Net1FR1 after being set initially.  
Display Conditions – This option value only appears for a user data port.  
Initialize_From_Interface – The LMI type supported on this frame relay link will be  
configured to match the LMI protocol discovered from the attached Network line or DTE  
device. Once a protocol has become active, the protocol will be set to the protocol  
discovered (Standard, Annex-A or Annex-D) on the frame relay link. The protocol will not  
be updated after being initially discovered. Frame relay links on user data ports discover  
the LMI protocol from an attached device via LMI status polls. Frame relay links on the  
network interface discover LMI protocol by sending polls to an attached Network line and  
“listening” for correct poll response messages.  
Auto_On_LMI_Fail – The LMI type supported on this frame relay link will be configured to  
match the LMI protocol discovered from the attached Network line or the DTE device  
whenever an LMI Link Down failure occurs. This option is available for frame relay links on  
the Port and network interfaces. Frame relay links on user data ports discover the LMI  
protocol from LMI status polls by attached DTE devices. Frame relay links on the network  
interface discover LMI protocol by sending polls to an attached Network line and  
“listening” for correct poll response messages.  
Standard – Supports Standard LMI and the Stratacom enhancements to the Standard  
LMI.  
Annex-A – Supports LMI as specified by Q.933, Annex A.  
Annex-D – Supports LMI as specified by ANSI T1.617, Annex D.  
3-60  
December 2002  
9000-A2-GB31-00  
 
           
3. Configuration Options  
Table 3-24. Interface Frame Relay Options (2 of 3)  
Traffic Policing  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Determines whether or not CIR (Committed Information Rate) and EIR (Excess  
Information Rate) will be enforced by the unit on frames being sent on network frame relay  
links.  
Enable – CIR and EIR are enforced.  
Frames that exceed CIR will be marked Discard Eligible (DE). These frames are  
counted in the Above CIR but within EIRcategory until this category is full.  
Once full, additional frames are counted as being in the Within CIRcategory.  
Frames in excess of EIR will be discarded.  
For CSU/DSUs only, DE frames received from the external router are credited as  
frames transmitted above CIR. They are credited as frames transmitted between  
CIR and EIR until that count reaches its limit, at which point they are counted as  
frames transmitted above EIR.  
Disable – CIR and EIR are not enforced.  
LMI Parameters  
Possible Settings: System, Custom  
Default Setting: System  
Allows you to use the system LMI options, or to set specific LMI options for this interface.  
System – Use system LMI options (see Table 3-1, System Frame Relay and LMI  
Options).  
Custom – Use the following options in this table to configure LMI parameters.  
Frame Relay DS0s Base Rate  
Possible Settings: Nx64, Nx56  
Default Setting: Nx64  
Selects the base rate for the DS0s allocated to frame relay on the network interface.  
Nx64 – The base rate is 64 Kbps.  
Nx56 – The base rate is 56 Kbps.  
LMI Error Event (N2)  
Possible Settings: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10  
Default Setting: 3  
Configures the LMI-defined N2 parameter, which sets the number of errors that can occur  
on the LMI link before an error is reported. Applies to both the user and network sides of a  
UNI.  
1 – 10 – Specifies the maximum number of errors.  
9000-A2-GB31-00  
December 2002  
3-61  
 
                   
3. Configuration Options  
Table 3-24. Interface Frame Relay Options (3 of 3)  
LMI Clearing Event (N3)  
Possible Settings: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10  
Default Setting: 1  
Configures the LMI-defined N3 parameter, which sets the number of error-free messages  
that must be received before clearing an error event. Applies to both the user and network  
sides of a UNI.  
1 – 10 – Specifies how many error-free messages it will take to clear the error event.  
LMI Status Enquiry (N1)  
Possible Settings: 1, 2, 3, 4, . . . 255  
Default Setting: 6  
Configures the LMI-defined N1 parameter, which sets the number of status enquiry polling  
cycles that the user side of the LMI initiates before a full status enquiry is initiated. Applies  
to the user side of a UNI only.  
1 – 255 – Specifies the number of status enquiry polling cycles that can be initiated before  
a full status enquiry is initiated.  
LMI Heartbeat (T1)  
Possible Settings: 5, 10, 15, 20, 25, 30  
Default Setting: 10  
Configures the LMI-defined T1 parameter, which sets the number of seconds between the  
initiation of status enquiry messages on the user side of the LMI. Applies to the user side  
of a UNI only.  
5 – 30 – Specifies the number of seconds between the initiation of status enquiry  
messages in increments of 5.  
LMI Inbound Heartbeat (T2)  
Possible Settings: 5, 10, 15, 20, 25, 30  
Default Setting: 15  
Configures the LMI-defined T2 parameter, which sets the number of seconds between the  
receipt of status enquiry messages on the network side of the LMI. Applies to the network  
side of a UNI only.  
5 – 30 – Specifies the number of seconds between the receipt of status enquiry messages  
in increments of 5.  
LMI N4 Measurement Period (T3)  
Possible Settings: 5, 10, 15, 20, 25, 30  
Default Setting: 20  
Configures the LMI-defined T3 parameter, which is the time interval (in seconds) that the  
network side of the LMI uses to measure the maximum number of status enquiry  
messages that have been received (N4) from the user side.  
5 – 30 – Specifies the interval of time in increments of 5.  
3-62  
December 2002  
9000-A2-GB31-00  
 
                         
3. Configuration Options  
Configuring PPP for an Interface  
Select PPP from the interface’s menu to display or change the PPP options for an  
individual interface (see Table 3-25, Interface PPP Options). PPP is not an option  
on the Network or Data Ports menus unless Service Type is PPP.  
Main MenuConfiguration[Network/Data Ports] PPP  
Table 3-25. Interface PPP Options  
Circuit Type  
Possible Settings: Standard, IP Enabled  
Default Setting:  
For a user data port link: Standard  
For a network link: IP Enabled  
Specifies the type of PPP circuit configured on the interface.  
Standard – The circuit operates normally, supporting neither Payload Management nor  
IP Enabled characteristics. This option value only appears for a user data port.  
IP Enabled – The circuit is IP Enabled. This option is read-only for the network interface.  
Keep Alive  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Determines whether Link Control Protocol (LCP) echo requests are generated on the  
circuit.  
Enable – LCP Echo-Request codes are generated on the circuit, and Echo-Reply codes  
are generated for Echo-Requests received from the remote end.  
Disable – LCP Echo-Request codes are not generated on the circuit, but Echo-Reply  
codes are generated for Echo-Requests received from the remote end.  
DS0 Base Rate  
Possible Settings: Nx64, Nx56  
Default Setting: Nx64  
Selects the base rate for the DS0s allocated to PPP on the network interface.  
Display Conditions – This option appears only for network interfaces that support  
DS0s.  
Nx64 – The base rate is 64 Kbps.  
Nx56 – The base rate is 56 Kbps.  
9000-A2-GB31-00  
December 2002  
3-63  
 
               
3. Configuration Options  
Manually Configuring DLCI Records  
The Auto-Configuration feature automatically configures DLCI Records and their  
PVC Connections. DLCI Records can also be created manually (see Table 3-26,  
Main Menu Configuration [Network/Data Port/ISDN/Virtual Router Ports]  
DLCI Records  
Available paths to DLCI Records Options depend on the Service Type and  
FrameSaver model:  
n
DLCI Records is not an option on the Network menu unless Service Type is  
Frame Relay  
n
n
n
Data Port is available only on CSU/DSUs  
ISDN is available only when the FrameSaver unit has an ISDN DBM installed  
Virtual Router Ports is available only on the FrameSaver SLV Router  
Typically, DLCI Records only need to be configured when building Management  
PVCs between the NOC and the central site unit; the unit automatically configures  
non-management DLCI Records and PVC Connections.  
Table 3-26. DLCI Record Options (1 of 4)  
DLCI Number  
Possible Settings: 16 – 1007  
Default Setting: Initially blank; no default.  
Specifies the number for the DLCI in the DLCI record. The parameter determines which  
DLCI record is used for transferring data on a particular frame relay interface. DLCI  
numbers range from 0to1023. However, the numbers 0 – 15 and 1008 – 1023 are  
reserved. Entry of an invalid number results in the error message Value Out of Range  
(16–1007). If the DLCI number is part of a connection, this field is read-only.  
NOTES:  
– If a DLCI number is not entered, the DLCI record is not created.  
– The DLCI number entered must be unique for the interface.  
– Changing settings for this configuration option causes the FrameSaver unit to abort  
any active frame relay tests.  
16 – 1007 – Specifies the DLCI number (inclusive).  
3-64  
December 2002  
9000-A2-GB31-00  
 
               
3. Configuration Options  
Table 3-26. DLCI Record Options (2 of 4)  
DLCI Type  
Possible Settings: Standard, Multiplexed, IP Enabled  
Default Setting:  
For user data port DLCIs: Standard  
For network interface DLCIs: Multiplexed  
Specifies whether the DLCI is standard or multiplexed. This field is read-only when the  
selected DLCI is used in a PVC or Management link connection and the DLCI Type is  
Standard.  
Display Conditions – This option does not appear for a user data port or a virtual router  
port, and it cannot be changed if the DLCI is specified as the TS Access Management  
Link.  
Standard – Supports standard DLCIs as specified by the Frame Relay Standards. Use  
this setting when a non-FrameSaver unit is at the other end.  
Multiplexed – Enables multiplexing of multiple connections into a single DLCI. Allows a  
single PVC through the frame relay network to carry multiple DLCIs as long as these  
connections are between the same two endpoints (proprietary). Do not select Multiplexed  
unless there are FrameSaver units at both ends of the connection.  
IP Enabled – Enables connection to one or more endpoints through a Layer 3 network. A  
Payload Management PVC is created as well as the IP Enabled DLCI.  
CIR (bps)  
Possible Settings:  
For 9123, 9126, 9128: 0 – 1536000  
For 9520, 9520-ILM: 0 – 44210000  
For 9623, 9626: 0 – 64000  
For 9820-2M: 0 – 2048000  
For 9820-8M: 0 – 8192000  
For 9820-45M: 0 – 44210000  
Default Setting: 0  
Determines the data rate for the DLCI that the network commits to accept and carry  
without discarding frames; the CIR in bits per second. Entry of an invalid rate causes the  
error message Value Out of Range (0 x), where x = the maximum line rate  
available on the port.  
0 – maximum – Specifies the network-committed data rate.  
Tc  
Possible Settings: 1 – 65535  
Default Setting: Read Only  
Displays the DLCI’s calculated value of its committed rate measurement interval (Tc) in  
milliseconds. This value is calculated based upon the settings for the Committed Burst  
Size Bc (Bits) and CIR (bps) options.  
9000-A2-GB31-00  
December 2002  
3-65  
 
           
3. Configuration Options  
Table 3-26. DLCI Record Options (3 of 4)  
Committed Burst Size Bc (Bits)  
Possible Settings: CIR, Other  
Default Setting: CIR  
Specifies whether the DLCI’s committed burst size will follow the CIR, or whether it will be  
entered independently. This value is the maximum amount of data that the service  
provider has agreed to accept during the committed rate measurement interval (Tc).  
CIR – Uses the value in the CIR (bps) option as the committed burst size (Bc). The Bc and  
excess burst size (Be) options are updated when a CIR update is received from the  
network switch.  
Other – Allows you to specify the committed burst size for the DLCI. When Other is  
selected, the Bc and Be values must be manually entered and maintained, as well.  
Bc  
Possible Settings:  
For 9123, 9126, 9128: 0 – 1536000  
For 9520, 9520-ILM: 0 – 44210000  
For 9623, 9626: 0 – 64000  
For 9820-2M: 0 – 2048000  
For 9820-8M: 0 – 8192000  
For 9820-45M: 0 – 44210000  
Default Setting: 0  
Allows you to display or change the DLCI’s committed burst size.  
Display Conditions – This option only appears when Committed Burst Size is set to  
Other.  
0 – maximum – Specifies the DLCI’s committed burst size.  
Excess Burst Size (Bits)  
Specifies the maximum amount of data in bits that the network may accept beyond the  
CIR without discarding frames.  
Be  
Possible Settings:  
For 9123, 9126, 9128: 0 – 1536000  
For 9520, 9520-ILM: 0 – 44210000  
For 9623, 9626: 0 – 64000  
For 9820-2M: 0 – 2048000  
For 9820-8M: 0 – 8192000  
For 9820-45M: 0 – 44210000  
Default Setting: [Maximum]  
Allows you to display or change the DLCI’s excess burst size.  
0 – maximum – Specifies the DLCI’s excess burst size.  
3-66  
December 2002  
9000-A2-GB31-00  
 
       
3. Configuration Options  
Table 3-26. DLCI Record Options (4 of 4)  
DLCI Priority  
Possible Settings: Low, Medium, High  
Default Setting: High  
Specifies the relative priority for data received on the DLCI from an attached device (also  
known as quality of service). All data on Port 1 is cut-through, as long as there is no  
higher-priority data queued from another user port. The DLCI priority set for an interface  
applies to data coming into that interface. For example, the priority set for DLCIs on Port 1  
applies to data coming into Port 1 from the attached equipment (such as a router).  
NOTE: For units with multiple user data ports, since pipelining occurs on Port-1, it is  
recommended that higher priority data be connected to Port-1 .  
Display Conditions – This option is not available for the network interface or, if the  
model has ISDN backup capability, an ISDN DBM interface.  
Low – Data configured for the DLCI has low priority.  
Medium – Data configured for the DLCI has medium priority.  
High – Data configured for the DLCI has high priority.  
Outbound Management Priority  
Possible Settings: Low, Medium, High  
Default Setting: Medium  
Specifies the relative priority for management traffic sent on management PVCs on this  
DLCI to the network.  
Display Conditions – This option is not available on a user data port or a virtual router  
port.  
Low – Management data configured for the DLCI has low priority.  
Medium – Management data configured for the DLCI has medium priority.  
High – Management data configured for the DLCI has high priority.  
Backup Group  
Possible Settings: A, B, C, . . . Z, None  
Default Setting: None  
Assigns DLCIs to a backup group so backup does not take place unless all DLCIs in the  
group are no longer operational or latency has been exceeded. Backup is terminated  
when one DLCI in the group is operational again. This feature reduces backup charges  
when redundant PVCs have been configured.  
Display Conditions – This option is not available on a user data port, a virtual router  
port, or an ISDN DBM interface.  
A – Z – Specifies the designation for this group of DLCIs. Only DLCIs in a PVC will be  
considered part of a Backup Group.  
None – No Backup Groups have been set up.  
9000-A2-GB31-00  
December 2002  
3-67  
 
       
3. Configuration Options  
Configuring Circuit Records for the Network Interface  
For Models 9783 and 9788, circuit records can be created or modified and PVCs  
can be created based on existing DLCIs using the Network Circuit Records  
screen.  
Main Menu Configuration Network Circuit Records  
If any DLCI records exist, you may enter a DLCI number at the bottom of the  
screen to display, copy from, or modify a DLCI record.  
Select CreatePVC to create a new PVC based on an existing DLCI record.  
Table 3-27. Circuit Records Options (1 of 3)  
DLCI Number  
Possible Settings: 16 – 1007  
Default Setting: Initially blank  
Specifies the number for the DLCI in the DLCI record. The parameter determines which  
DLCI record is used for transferring data on a particular frame relay interface. DLCI  
numbers range from 0–1023 with numbers 0–15 and 1008–1023 reserved. Entry of an  
invalid number results in the error message Value Out of Range (16–1007). If the  
DLCI number is part of a connection, this field is read-only.  
NOTES:  
– If a DLCI number is not entered, the DLCI record is not created.  
– The DLCI number entered must be unique for the interface.  
– Changing this setting causes the FrameSaver unit to abort any active frame relay  
tests.  
16 – 1007 – Specifies the DLCI number.  
VPI,VCI Number  
Possible Settings:  
For the VPI: 0 – 15  
For the VCI: 32 – 255  
Default Setting: Initially blank  
Specifies the VPI and VCI. Entry of an invalid number results in the error message Value  
Out of Range (0 – 15)for the VPI, and Value Out of Range (32 – 255)for  
the VCI. The VPI/VCI must be unique on the ATM link.  
0 – 15 – Specifies the VPI.  
32 – 255 – Specifies the VCI.  
3-68  
December 2002  
9000-A2-GB31-00  
 
             
3. Configuration Options  
Table 3-27. Circuit Records Options (2 of 3)  
DLCI Type  
Possible Settings: Standard, Multiplexed, IP Enabled  
Default Setting: Multiplexed  
Specifies whether the DLCI is standard, multiplexed, or IP Enabled. This field is read-only  
when the selected DLCI is used in a PVC or Management link connection and the DLCI  
Type is Standard.  
Display Conditions – This option cannot be changed if the DLCI is specified as the TS  
Access Management Link. It is not applicable when FRF.8 Encapsulation Mode is set  
to Translational (see Table 3-28, Network ATM Options).  
Standard – Supports standard DLCIs as specified by the Frame Relay Standards. Use  
this setting when a non-FrameSaver unit is at the other end.  
Multiplexed – Enables multiplexing of multiple connections into a single DLCI. Allows a  
single PVC through the frame relay network to carry multiple DLCIs as long as these  
connections are between the same two endpoints (proprietary). Do not select Multiplexed  
unless there are FrameSaver units at both ends of the connection.  
IP Enabled – Enables connection to one or more endpoints through a Layer 3 network. A  
Payload Management PVC is created as well as the IP Enabled DLCI.  
CIR (bps)  
Possible Settings:  
9783: 0 – 2320000  
9788: 0 – 2312000  
Default Setting: 0  
Determines the data rate in bits per second for the DLCI that the network commits to  
accept and carry without discarding frames. Entry of an invalid rate causes the error  
message Value Out of Range (0 – x), where x is the maximum line rate available  
on the port.  
0 – maximum – Specifies the network-committed data rate.  
Tc  
Possible Settings: 1 – 65535  
Default Setting: Read-Only  
Displays the DLCI’s calculated value of its committed rate measurement interval (Tc) in  
milliseconds based on the CIR (bps) and Committed Burst Size Bc (Bits) settings.  
Committed Burst Size Bc (Bits)  
Possible Settings: CIR, Other  
Default Setting: CIR  
Specifies whether the DLCI’s committed burst size uses the CIR setting or is entered  
independently. This value is the maximum amount of data that the service provider has  
agreed to accept during the committed rate measurement interval (Tc).  
CIR – Uses the value in the CIR (bps) option as the committed burst size (Bc). The Bc and  
excess burst size (Be) options are updated when a CIR update is received from the  
network switch.  
Other – Allows you to specify the committed burst size for the DLCI. When Other is  
selected, the Bc and Be values must be manually entered and maintained.  
9000-A2-GB31-00  
December 2002  
3-69  
 
                   
3. Configuration Options  
Table 3-27. Circuit Records Options (3 of 3)  
Bc  
Possible Settings:  
9783: 0 – 2320000  
9788: 0 – 2312000  
Default Setting: 0  
Allows you to display or change the DLCI’s committed burst size.  
Display Conditions – This option appears only when Committed Burst Size is set  
to Other.  
0 – maximum – Specifies the DLCI’s committed burst size.  
Excess Burst Size Be (Bits)  
Possible Settings:  
9783: 0 – 2320000  
9788: 0 – 2312000  
Default Setting:  
9783: 2320000  
9788: 2312000  
Specifies the maximum amount of data in bits that the network may accept beyond the  
CIR without discarding frames.  
Display Conditions – This option appears only when Committed Burst Size is set  
to Other.  
0 – maximum – Specifies the DLCI’s committed burst size.  
Outbound Management Priority  
Possible Settings: Low, Medium, High  
Default Setting: Medium  
Specifies the relative priority for management traffic sent on management PVCs on this  
DLCI to the network.  
Low – Management data configured for the DLCI has low priority.  
Medium – Management data configured for the DLCI has medium priority.  
High – Management data configured for the DLCI has high priority.  
3-70  
December 2002  
9000-A2-GB31-00  
 
           
3. Configuration Options  
Configuring ATM for the Network Interface  
For Models 9783 and 9788, select ATM from the Network menu to display or  
change ATM option settings (see Table 3-28, Network ATM Options).  
Main MenuConfigurationNetwork ATM  
Table 3-28. Network ATM Options  
Cell Payload Scrambling  
Possible Settings: Enable, Disable  
Default Setting:  
9783 – If DSLAM Type is set to Paradyne: Enable  
9783 – If DSLAM Type is set to a non-Paradyne DSLAM: Disable  
9788: Enable  
Specifies whether the 48-byte information field of ATM cells is scrambled/descrambled  
per ANSI T1.646 on this ATM link.  
NOTE: For the 9783 CSU/DSU, the default setting is changed based upon the DSLAM  
Type setting. See DSLAM Type (9783) on page 2-5 for more information.  
Enable – Activates scrambling/descrambling of transmitted or received ATM cells.  
Disable – No scrambling/descrambling is performed.  
Cell Delineation Error Event Threshold  
Possible Settings: 1 – 1000  
Default Setting: 10  
Specifies the number of OCD (Out of Cell Delineation) events that must occur in a  
one-minute interval for an LCD (Loss of Cell Delineation) alarm to be declared.  
1 – 1000 – Specifies the LCD alarm threshold.  
FRF.8 Encapsulation Mode  
Possible Settings: Translational, Transparent  
Default Setting: Transparent  
Specifies the type of FRF.8 upper-layer protocol encapsulation used on the link for each  
pair of interoperable Frame Relay and ATM PVCs.  
Translational – Encapsulated data is translated (RFC 1490 to RFC 1483). FrameSaver  
multiplexing and SLV communications are not supported in this mode.  
Transparent – Encapsulated data is forwarded without being translated.  
ILMI  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Specifies the state of the Integrated Local Management Interface (ILMI). ILMI can be used  
in support of hybrid management, allowing access to the endpoint from a DSL provider’s  
Network Operation Center using the same management PVC that is used to manage the  
DSLAM.  
Enable – The ILMI channel is enabled. SNMP traffic, embedded in the ATM cells, is  
supported.  
Disable – The ILMI channel is disabled.  
9000-A2-GB31-00  
December 2002  
3-71  
 
                                   
3. Configuration Options  
Configuring PVC Connections  
The Auto-Configuration feature automatically configures PVC Connections and  
their DLCI Records. PVC Connections can also be created manually (see  
Main MenuConfigurationPVC Connections  
From this screen, you can go directly to the Management PVC screen by selecting  
the MgmtPVCs function key for easy movement between screens.  
Quick removal of unused DLCIs (and ISDN Link Profiles, except for HQ_Site, if the  
model has an ISDN DBM installed) included in an existing PVC Connection is also  
available when the Delete function key is selected and you respond Yes to the  
Remove otherwise unused components associated with the  
deleted PVC?prompt.  
Table 3-29. PVC Connection Options (1 of 4)  
Source Link  
Possible Settings: Port-n, ISDN Link Name, Net1-FR1, Rtr-S0  
Default Setting: Initially blank; no default.  
Specifies the frame relay interface that starts a PVC connection; the from end of a from-to  
link. The only valid settings for this configuration option are frame relay interfaces that  
have at least one DLCI or EDLCI defined that are not part of a PVC connection or  
management link. For example, if Port-1 has no DLCIs defined, Port-1 would not appear  
as a valid setting.  
Net1-FR1 – Specifies that the network interface be used in the connection.  
ISDN Link Name – For units with ISDN backup capability, specifies the ISDN link of the  
DBM as the source link. This can be any nonnull link name configured on an ISDN frame  
relay link.  
Port-n – For CSU/DSUs, specifies that the frame relay link on the user data port be used  
in the connection.  
Rtr-S0 – For FrameSaver routers, specifies that the frame relay link on the virtual router  
port be used in the connection.  
Clear All – Clears all Link and DLCI settings, and suppresses EDLCIs.  
Source DLCI  
Possible Settings: 16 – 1007  
Default Setting: Initially blank; no default.  
Specifies the source DLCI for a frame relay interface. The DLCI must be defined and  
cannot be part of a PVC connection or management link. For multiplexed DLCIs, at least  
one EDLCI must be unconnected for the DLCI to be a valid selection.  
NOTE: Source DLCI has no value if Source Link contains no value.  
16 – 1007 – Specifies the DLCI number.  
3-72  
December 2002  
9000-A2-GB31-00  
 
             
3. Configuration Options  
Table 3-29. PVC Connection Options (2 of 4)  
Source EDLCI  
Possible Settings: 0 – 62  
Default Setting: Initially blank; no default.  
Specifies the source Embedded Data Link Connection Identifier (EDLCI) for a frame relay  
interface when a multiplexed DLCI record is selected as one end of a connection.  
Display Conditions – This option only appears when Source DLCI contains a  
multiplexed DLCI record number.  
0 – 62 – Specifies the EDLCI number.  
Primary Destination Link  
Possible Settings: Net1-FR1, ISDN Link Name, Rtr-S0  
Default Setting: Initially blank; no default.  
Specifies the frame relay interface used as the primary destination link; the to end of a  
from-to link. The only valid settings for this configuration option are frame relay interfaces  
that have at least one DLCI or EDLCI defined which are not part of a PVC connection or  
management link. For example, if the network interface has no DLCIs defined, Net1-FR1  
would not appear as a valid setting.  
Net1-FR1 – Specifies the Network interface as the destination link.  
ISDN Link Name – For units with ISDN backup capability, specifies the ISDN link of the  
DBM as the destination of the connection. This can be any nonnull link name configured  
on an ISDN frame relay link.  
Rtr-S0 – For FrameSaver routers, specifies the virtual router port as the destination link.  
Primary Destination DLCI  
Possible Settings: 16 – 1007  
Default Setting: Initially blank; no default.  
Specifies the primary destination DLCI for a frame relay interface. The DLCI must be  
defined and cannot be part of a PVC connection or management link. For multiplexed  
DLCIs, at least one EDLCI must be unconnected for the DLCI to be a valid selection.  
NOTES:  
– Primary Destination DLCI has no value if Primary Destination Link contains no  
value.  
– When an ISDN DBM is installed and the DLCI assigned to the PVC is in a Backup  
Group (see Table 3-26, DLCI Record Options), the letter designation assigned to  
the group of DLCIs appears next to the primary destination DLCI number on the  
Management PVCs Options screen.  
16 – 1007 – Specifies the DLCI number.  
9000-A2-GB31-00  
December 2002  
3-73  
 
                   
3. Configuration Options  
Table 3-29. PVC Connection Options (3 of 4)  
Primary Destination EDLCI  
Possible Settings: 0 – 62  
Default Setting: Initially blank; no default.  
Specifies the primary destination Embedded Data Link Connection Identifier (EDLCI) for a  
frame relay interface when a multiplexed DLCI record is selected as one end of a  
connection.  
Display Conditions – This option only appears when the Primary Destination DLCI  
contains a multiplexed DLCI record number. For a DLCI that is:  
– IP Enabled, IP appears in this field  
– Payload Managed (but not IP Enabled), PM appears in this field  
0 – 62 – Specifies the EDLCI number.  
Alternate Destination Link  
Possible Settings: Net1-FR1, ISDN Link Name  
Default Setting: Initially blank; no default.  
Specifies the frame relay interface used as the alternate destination link; the to end of a  
from-to link that is used for backup when the primary destination link or DLCI is out of  
service. The only valid settings for this configuration option are frame relay interfaces that  
have at least one DLCI or EDLCI defined which are not part of a PVC connection or  
management link. For example, if ISDN Link Name has no DLCIs defined, the ISDN link  
name would not appear as a valid setting.  
Net1-FR1 – Specifies the Network interface as the destination link.  
ISDN Link Name – Specifies the ISDN link of the DBM as the destination of the  
connection. This can be any non-null link name configured on an ISDN frame relay link on  
an installed DBM.  
Clear Alternate – Clears the Alternate Destination Link and Alternate Destination DLCI  
settings, and suppresses Alternate Destination EDLCI.  
Alternate Destination DLCI  
Possible Settings: 16 – 1007  
Default Setting: Initially blank; no default.  
Specifies the alternate destination Data Link Connection Identifier (DLCI) for a frame relay  
interface used for backup. The DLCI must be defined and cannot be part of a PVC  
connection or management link. For multiplexed DLCIs, at least one EDLCI must be  
unconnected for the DLCI to be a valid selection.  
Display Conditions – This option does not appear when the Alternate Destination Link  
contains no value.  
16 – 1007 – Specifies the DLCI number.  
3-74  
December 2002  
9000-A2-GB31-00  
 
                 
3. Configuration Options  
Table 3-29. PVC Connection Options (4 of 4)  
Alternate Destination EDLCI  
Possible Settings: 0 – 62  
Default Setting: Initially blank; no default.  
Specifies the alternate destination Embedded Data Link Connection Identifier (EDLCI) for  
a frame relay interface when a multiplexed DLCI record is selected as one end of a  
backup connection.  
Display Conditions – This option only appears when the Alternate Destination DLCI  
contains a multiplexed DLCI record number.  
0 – 62 – Specifies the EDLCI number.  
9000-A2-GB31-00  
December 2002  
3-75  
 
         
3. Configuration Options  
Configuring the IP Path List  
Select IP Path List (Static) from the Configuration Edit/Display menu to display or  
change the list of static path IP addresses explicitly defined in the unit.  
Main MenuConfigurationIP Path List (Static)  
The IP Path List (Static) screen appears, showing any existing static paths. Paths  
discovered as SLV packets are received from other FrameSaver units are not  
shown. To view the entire current IP Path List, use the IP Path Connection Status  
screen. See the FrameSaver SLV Operations Guide for more information.  
Procedure  
To add a static path:  
1. Select New. The following prompt appears:  
Enter IP Address (press ESC to abort): ___.___.___.___ FWD: No  
2. Enter the IP address of a static path and select a forwarding option of No or  
Yes using the spacebar.  
3. Press enter. Select Save.  
Table 3-30. IP Path List  
IP Address  
Possible Settings: 000.000.000.001 – 126.255.255.255, 128.000.000.000 –  
223.255.255.255  
Default Setting: Initially blank; no default.  
Specifies the address of a FrameSaver or other device at the other end of a path.  
000.000.000.001 – 126.255.255.255, 128.000.000.000 – 223.255.255.255 – Specifies the  
address of a device.  
FWD  
Possible Settings: No, Yes  
Default Setting: No  
Determines whether this path list item is sent to all other addresses in the list that  
represent FrameSaver devices.  
No – The IP address associated with this path list item is not distributed.  
Yes – The IP address associated with this path list entry is distributed to devices in the list.  
3-76  
December 2002  
9000-A2-GB31-00  
 
   
3. Configuration Options  
Configuring Node IP Information  
Select Node IP to display, add, or change the information necessary to support  
general IP communications for the node (see Table 3-31, Node IP Options). When  
deploying units to remote sites, minimally configure the Node IP Address and  
Subnet Mask.  
Main MenuConfigurationManagement and CommunicationNode IP  
This set of configuration options includes a Troubleshooting (TS) Management  
Access Link feature to help service providers isolate device problems within their  
networks. This feature allows Telnet or FTP access to the unit on this link.  
Troubleshooting over this link is essentially transparent to customer operations.  
No alarms or SNMP traps are generated to create nuisance alarms for the  
customer.  
TS_Access_Management_Link is initially disabled in most models, but the link can  
be enabled at any time. Any valid network Management PVC created on a  
standard DLCI can be used. When enabled, a troubleshooting link can be  
accessed any time the service provider requests access. An assigned security  
level can also control access.  
When a DLCI has been defined as the troubleshooting management link, the link  
is identified in the status field at the bottom of the Management PVC Entry screen  
with the Note: This PVC has been designated as the TS Access  
Management Linkmessage.  
NOTE:  
The unit may come from the factory with a TS Management PVC already set  
up (e.g., 980).  
Table 3-31. Node IP Options (1 of 4)  
Node IP Address  
Possible Settings: 001.000.000.000 – 223.255.255.255, Clear  
Default Setting: Clear (000.000.000.000)  
Specifies the IP address needed to access the node. Since an IP address is not bound to  
a particular port, it can be used for remote access via a management PVC.  
001.000.000.000 – 223.255.255.255 – Shows the IP address for the node, which can be  
viewed or edited.  
Clear – Fills the node IP address with zeros.  
3-78  
December 2002  
9000-A2-GB31-00  
 
                 
3. Configuration Options  
Table 3-31. Node IP Options (2 of 4)  
Node Subnet Mask  
Possible Settings: 000.000.000.000 – 255.255.255.255, Clear  
Default Setting: 000.000.000.000  
Specifies the subnet mask needed to access the node. Since the subnet mask is not  
bound to a particular port, it can be used for remote access via a management PVC.  
000.000.000.000 – 255.255.255.255 – Shows the subnet mask for the node, which can be  
viewed or edited.  
Clear – Fills the node subnet mask with zeros. When the node’s subnet mask is all zeros,  
the IP protocol creates a default subnet mask based upon the class of the IP address:  
Class A: 255.000.000.000, Class B: 255.255.000.000, or Class C: 255.255.255.000.  
Default IP Destination  
Possible Settings: None, Modem, COM, Ethernet, PVCname  
Default Setting: None  
Specifies an IP destination to route data that does not have a specifically defined route.  
Examples:  
If the default IP network is connected to the communications port, select COM.  
If the default IP network is connected to a far-end device over the management PVC  
named London for the remote device located in the London office, select the PVC  
name London (as defined by the Name configuration option, Table 3-32, Management  
PVC Options).  
NOTE: If the link to the IP destination selected as the default route becomes disabled  
or down, the unrouteable data will be discarded. Make sure that the link selected is  
operational, and if that link goes down, change the default destination.  
CAUTION: Use care when configuring a default route to an interface that has a subnet  
route configured at a remote end where the NMS, router, LAN adapter, terminal server,  
etc. is connected. Communicating with an unknown IP address on the subnet will  
cause temporary routing loops, which will last 16 iterations times the retry count.  
None – No default network destination is specified. Unrouteable data will be discarded.  
This is the recommended setting.  
Modem – Specifies that the default destination is connected to the modem port. Only  
appears when the modem port Use option is set to Net Link.  
COM – Specifies that the default destination is connected to the COM port. Only appears  
when Port Use is set to Net Link (see Table 3-38, Communication Port Options).  
Ethernet – For the FrameSaver SLV 9126 or 9128, specifies that the default destination is  
connected to the Ethernet port. Only appears when the Ethernet port’s Interface Status  
option is enabled. When selected, the Default Gateway Address must also be configured  
PVCname – Specifies a name for the management PVC. Only appears when a  
management PVC name is defined for the node. For example, when the network is  
connected to a remote device located in the London office, London can be specified as  
the PVC name, which is the link between the local FrameSaver unit and the one located in  
London. London would appear as one of the available selections.  
9000-A2-GB31-00  
December 2002  
3-79  
 
                 
3. Configuration Options  
Table 3-31. Node IP Options (3 of 4)  
Management MTU Size  
Possible Settings: 90 – 1500  
Default Setting: 1500  
Specifies the Maximum Transmission Unit (MTU) for management traffic transmitted on  
standard DLCIs, EDLCIs, IP tunnels, and Payload Management circuits.  
90 – 1500 – Specifies the MTU size.  
TS Access Management Link  
Available Settings: None, PVCname  
Default Setting: None  
Specifies a troubleshooting management link for the special needs of network service  
providers.  
If the setting is changed from the management PVC name to None, the Delete the  
Management PVC PVCname and the associated DLCI Record?prompt appears.  
If you select:  
No – The link designation is removed and the option is set to None.  
Yes – The link designation is removed and the option is set to None, and the link  
and its DLCI will be deleted.  
Display Conditions – This option appears only when Service Type is Frame Relay.  
None – Disables or does not specify a TS Access Management Link.  
PVCname – Specifies the name of the TS Management PVC. This selection only appears  
when a dedicated management PVC has been defined on the network frame relay link as  
a DLCI with DLCI Type set to Standard.  
TS Management Link Access Level  
Available Settings: Level-1, Level-2, Level-3  
Default Setting: Level-1  
Specifies the highest access level allowed when accessing the unit via a Telnet or FTP  
session when the service provider is using the TS Access Management Link.  
Display Conditions – This option only appears when:  
Service Type on the Easy Install screen is set to Frame Relay.  
TS Access Management Link is set to a PVC name.  
NOTES:  
Telnet and FTP sessions on this link are not affected by the access level set by the  
Session Access Level, Login Required, or FTP Login Required option settings (see  
Telnet and FTP sessions on this link are affected by the Telnet Session, Inactivity  
Timeout, Disconnect Time and FTP Session option settings.  
Level-1 – Allows Telnet or FTP access by network service providers with the capability to  
view unit information, change configuration options, and run tests. This is the highest  
access level allowed. Use this setting when downloading files.  
Level-2 – Allows Telnet or FTP access by network service providers with the capability to  
view unit information and run tests only; they cannot change configuration options.  
Level-3 – Allows Telnet access by network service providers with the capability to view  
unit information only; they cannot change configuration options or run tests.  
3-80  
December 2002  
9000-A2-GB31-00  
 
         
3. Configuration Options  
Table 3-31. Node IP Options (4 of 4)  
TS Management SNMP Validation  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Specifies whether validation of community strings and IP addresses is performed for this  
management link.  
Display Conditions – This option only appears when:  
Service Type on the Easy Install screen is set to Frame Relay.  
TS Access Management Link is set to a PVC name.  
Enable – Validation of community strings and IP addresses is performed on SNMP traffic.  
Disable – No validation of community strings and IP addresses is performed.  
9000-A2-GB31-00  
December 2002  
3-81  
 
 
3. Configuration Options  
Configuring Management PVCs  
Select Management PVCs to define inband management links by adding or  
changing Management PVCs (see Table 3-32, Management PVC Options). First,  
DLCI records must have been configured for the interface where the Management  
additional information.  
Main MenuConfigurationManagement and Communication→  
Management PVCs  
Select New or Modify to add or change Management PVCs.  
n
n
When you select New, the configuration option field is blank.  
When you select Modify, the values displayed for all fields are based on the  
PVC ID number that you specified.  
These options do not apply when the Management PVC is designated as a  
additional information).  
From this screen, you can go directly to the PVC Connections screen by selecting  
the PVCConn function key for easy movement between screens.  
Select the Delete function key, a Management PVC ID#, and respond Yes to the  
Remove otherwise unused components associated with the  
deleted PVC?prompt for quick removal of unused DLCIs. If the Management  
PVC selected is defined as a trap Initial Route Destination, a Default IP  
Destination, or a TS Access Management Link, an ... Are You Sure?prompt is  
displayed to warn you.  
An IP Enabled circuit is identified by IPin the EDLCI or Type field of the  
Management PVCs Options screen. It may be viewed and modified, but not  
created or deleted. IP Enabled PVCs are created when an IP Enabled DLCI is  
created on the network interface, and deleted when the DLCI is deleted or  
changed to Standard.  
A payload management circuit is identified by PMin the EDLCI or Type field of the  
Management PVCs Options screen. If a payload management management  
circuit is deleted, the associated PVC remains standard, even if was a multiplexed  
PVC (automatically converted to standard) when it the management circuit was  
created.  
If an existing PVC with an associated payload managed management circuit is  
deleted, then the payload management circuit is also deleted.  
Table 3-32. Management PVC Options (1 of 6)  
Name  
Possible Settings: ASCII Text Entry  
Default Setting: Initially blank; no default.  
Specifies a unique name for the management PVC as referenced on screens (e.g.,  
Tampa for Tampa, Florida).  
ASCII Text Entry Enter a unique name for the management PVC (maximum length  
8 characters).  
3-82  
December 2002  
9000-A2-GB31-00  
 
         
3. Configuration Options  
Table 3-32. Management PVC Options (2 of 6)  
Payload Managed  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Specifies whether the PVC is payload managed.  
Display Conditions – This is a read-only field set to Enabled if the PVC is IP Enabled.  
Enable – The network PVC created will be monitored for the presence of IP frames  
containing the IP address specified in the Intf IP Address field. When such a frame is  
identified, it is extracted from the data stream and sent to the management stack.  
Disable – A normal management PVC is created using the specified DLCI or EDLCI.  
Intf IP Address  
Possible Settings: Node-IP-Address, Special (nnn.nnn.nnn.nnn)  
Default Setting: Node-IP-Address  
Specifies the IP address needed to access the unit via this management PVC, providing  
connectivity to an external IP network through the frame relay network.  
Node-IP-Address – Uses the IP address contained in the Node IP Address (see  
Special (001.000.000.000 – 223.255.255.255) – Allows you to display/edit an IP address  
for the unit’s management PVC when the IP address for this interface is different from the  
node’s IP address.  
Intf Subnet Mask  
Possible Settings: Node-Subnet-Mask, Calculate, Special (nnn.nnn.nnn.nnn)  
Default Setting: Node-Subnet-Mask  
Specifies the subnet mask needed to access the unit when the management PVC is  
providing connectivity to an external IP network (through frame relay) that requires a  
specific subnet mask for the interface.  
Node-Subnet-Mask – Uses the Interface IP Subnet contained in the Node-Subnet Mask  
configuration option (see Table 3-31, Node IP Options).  
Calculate – Calculates the subnet mask created by the IP protocol based on the class  
of the IP address (Class A: 255.000.000.000, Class B: 255.255.000.000, or  
Class C: 255.255.255.000). Cannot be displayed or edited.  
Special (000.000.000.000 – 255.255.255.255) – Allows you to edit/display the subnet  
mask for the management PVC when the subnet mask is different for this interface. A text  
field displays where you can enter the subnet mask for this unit’s management PVC.  
Set DE  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Specifies whether frames (packets) sent on a management PVC have the Discard Eligible  
(DE) bit set. This bit is used by the network to prioritize which frames to discard first during  
periods of network congestion. This allows management traffic to be viewed as lower  
priority than customer data.  
Enable – Sets the DE bit to one on all frames sent on the management PVC.  
Disable – Sets the DE bit to zero on all frames sent on the management PVC. This is the  
recommended setting, particularly for NSPs providing a managed network service.  
9000-A2-GB31-00  
December 2002  
3-83  
 
               
3. Configuration Options  
Table 3-32. Management PVC Options (3 of 6)  
Primary Link  
Possible Settings: Net1-FR1, Port-n, Rtr-S0, ISDN Link Name, Clear  
Default Setting: Initially blank; no default.  
Specifies the frame relay interface to use for this management PVC. The interface  
selected must have at least one DLCI (or DLCI with EDLCI) defined, which is not part of a  
PVC connection or already assigned as a management PVC.  
Display Conditions – The Port-1 setting does not appear if the PVC is IP Enabled or  
Payload Managed is enabled.  
Net1-FR1 – Specifies the network interface as the source link for the connection.  
Port-n – Specifies the frame relay link on the user data port as the destination link for the  
connection.  
Rtr-S0 – For FrameSaver routers, specifies that the vertual router port be used in the  
connection.  
ISDN Link Name – For units with ISDN backup capability, specifies the ISDN link on the  
DBM to be used in the connection. This can be any nonnull link name configured on an  
ISDN frame relay link on an installed DBM.  
Clear – Clears the link and the DLCI field, and suppresses the EDLCI field if the DLCI was  
multiplexed.  
Primary DLCI  
Possible Settings: 16 – 1007  
Default Setting: Initially blank; no default.  
Specifies the DLCI number used for the management PVC after the frame relay interface  
is selected.  
The DLCI must be defined for the link (i.e., has a DLCI record), and it must not be part of  
a PVC connection or already assigned as a management PVC. For multiplexed DLCIs, at  
least one EDLCI must be unconfigured for the DLCI.  
NOTES:  
– DLCI cannot be entered if the Link field is blank.  
– Clearing the Link also clears the DLCI.  
– When an ISDN DBM is installed and the DLCI assigned to the PVC is in a Backup  
Group (see Table 3-26, DLCI Record Options), the letter designation assigned to  
the group of DLCIs appears next to the primary destination DLCI number on the  
Management PVCs Options screen.  
16 – 1007 – Specifies the DLCI number (inclusive).  
3-84  
December 2002  
9000-A2-GB31-00  
 
       
3. Configuration Options  
Table 3-32. Management PVC Options (4 of 6)  
Primary EDLCI  
Possible Settings: 0 – 62  
Default Setting: Initially blank; no default.  
Specifies the EDLCI number used for a management PVC when a multiplexed DLCI is  
selected. EDLCIs identify individual connections within multiplexed DLCIs that are unique  
to those DLCIs.  
Use a unique EDLCI to identify an individual connection within a multiplexed DLCI. Use 0  
to identify the primary EDLCI. Use 1 – 62 to identify secondary EDLCIs. Use the primary  
EDLCI for customer data, which has a higher utilization rate than management data, with  
slightly less line overhead.  
Display Conditions – This option does not appear if the DLCI field does not reference a  
multiplexed DLCI, if the PVC is IP Enabled, or if Payload Managed is enabled.  
NOTE: Clearing the DLCI or changing it to a standard DLCI suppresses EDLCI field.  
0 – 62 – Specifies the EDLCI number (inclusive).  
Primary Link RIP  
Possible Settings: None, Proprietary, Standard_out  
Default Setting:  
For multiplexed DLCIs: Proprietary  
For nonmultiplexed DLCIs: Standard_out  
Specifies which Routing Information Protocol (RIP) is used to enable routing of  
management between FrameSaver units and attached equipment.  
Display Conditions – This option does not appear if the PVC is IP Enabled or Payload  
Managed is enabled.  
None – Does not use a routing protocol.  
Proprietary – Uses a proprietary variant of RIP version 1 to communicate routing  
information between FrameSaver units. A FrameSaver unit must be on the other end of  
the link. This is the factory default for management PVCs configured on multiplexed  
Proprietary-In – Like Proprietary, except that only local routes are passed to the far end.  
Standard_out – The device will send standard RIP messages to communicate routing  
information only about FrameSaver devices in the network. This is the factory default for  
management PVCs configured on standard DLCIs.  
NOTE: The router must be configured to receive RIP on the port connected to the  
FrameSaver unit for the management interface (e.g., Cisco: config-t, router  
RIP, int serialx, IP RIP Receive version 1, ctl-z WR). See Using RIP  
9000-A2-GB31-00  
December 2002  
3-85  
 
       
3. Configuration Options  
Table 3-32. Management PVC Options (5 of 6)  
Alternate Link  
Possible Settings: Net1-FR1, Port-n, ISDN Link Name, Clear  
Default Setting: Initially blank; no default.  
Specifies the frame relay interface to use for this management PVC as the alternate link.  
The interface selected must have at least one DLCI (or DLCI with EDLCI) defined, which  
is not part of a PVC connection or already assigned as a management PVC.  
Display Conditions – This option does not appear unless ISDN backup is available,  
and does not appear if Payload Managed is enabled.  
Net1-FR1 – Specifies the Network interface as the frame relay link.  
Port-n – Specifies the frame relay link on the user data port as the alternate destination  
link for the connection.  
ISDN Link Name – For units with ISDN backup capability, specifies the ISDN link of the  
DBM to be used in the connection. This can be any nonnull link name configured on an  
ISDN frame relay link on an installed DBM.  
Clear – Clears the link and the DLCI field, and suppresses the EDLCI field if the DLCI was  
multiplexed.  
Alternate DLCI  
Possible Settings: 16 – 1007  
Default Setting: Initially blank; no default.  
Specifies the alternate DLCI number to be used for the management PVC after the frame  
relay interface is selected.  
The DLCI must be defined for the link (i.e., has a DLCI record), and it must not be part of  
a PVC connection or already assigned as a management PVC. For multiplexed DLCIs, at  
least one EDLCI must be unconfigured for the DLCI.  
Display Conditions – This option does not appear if Payload Managed is enabled. The  
DLCI cannot be entered if the Link field is blank.  
NOTE: Clearing Link also clears the DLCI.  
16 – 1007 – Specifies the DLCI number (inclusive).  
Alternate EDLCI  
Possible Settings: 0 – 62  
Default Setting: Initially blank; no default.  
Specifies the alternate EDLCI number used for a management PVC when a multiplexed  
DLCI is selected for the frame relay link. EDLCIs identify individual connections within  
multiplexed DLCIs that are unique to those DLCIs.  
Use a unique EDLCI to identify an individual connection within a multiplexed DLCI. Use 0  
to identify the primary EDLCI. Use 1 – 62 to identify secondary EDLCIs. Use the primary  
EDLCI for customer data, which has a higher utilization rate than management data, with  
slightly less line overhead.  
Display Conditions – This option does not appear unless ISDN backup is available and  
the DLCI field does not reference a multiplexed DLCI. This option does not appear if  
Payload Managed is enabled.  
NOTE: Clearing the DLCI or changing it to a standard DLCI suppresses the EDLCI  
field.  
0 – 62 – Specifies the EDLCI number (inclusive).  
3-86  
December 2002  
9000-A2-GB31-00  
 
           
3. Configuration Options  
Table 3-32. Management PVC Options (6 of 6)  
Encapsulation  
Possible Settings: Routed  
Default Setting: Routed  
This read-only field specifies that the IP encapsulation used is RFC 1490/RFC 2427  
routed Network Level Protocol IDentifier (NLPID) encapsulation, and not SubNetwork  
Access Protocol (SNAP) encapsulation.  
Display Conditions – This option appears only if the PVC is IP Enabled or Payload  
Managed is enabled.  
Routed – IP encapsulation is routed NLPID.  
9000-A2-GB31-00  
December 2002  
3-87  
 
3. Configuration Options  
Configuring General SNMP Management  
Select General SNMP Management to add, change, or delete the information  
needed to allow the FrameSaver unit to be managed as an SNMP agent by the  
NMS supporting the SNMP protocols (see Table 3-33, General SNMP  
Main MenuConfigurationManagement and CommunicationGeneral  
SNMP Management  
You must have Level-1 access to display or configure these options.  
Table 3-33. General SNMP Management Options (1 of 2)  
SNMP Management  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Determines whether the FrameSaver unit can be managed as an SNMP agent by an  
SNMP-compatible NMS.  
Enable – Can be managed as an SNMP agent.  
Disable – Cannot be managed as an SNMP agent. The FrameSaver unit will not respond  
to SNMP messages nor send SNMP traps.  
Community Name 1  
Possible Settings: ASCII text entry, Clear  
Default Setting: Public in ASCII text field  
Specifies the first of two names that are allowed to access the objects in the FrameSaver  
unit’s MIB. The community name must be supplied by an external SNMP manager  
whenever the manager tries to access an object in the MIB.  
ASCII text entry – Adds to or changes Community Name 1 (maximum 255 characters).  
Clear – Clears Community Name 1.  
Name 1 Access  
Possible Settings: Read, Read/Write  
Default Setting: Read/Write  
Specifies the type of access allowed to the objects in the MIB. This is the type of access  
allowed for external SNMP managers accessing MIB objects using Community Name 1.  
Read – Allows read-only access (SNMP Get command). This includes all objects  
specified as either read-only or read/write in the MIB RFCs.  
Read/Write – Allows read and write access (SNMP get and set commands).  
Community Name 2  
Possible Settings: ASCII text entry, Clear  
Default Setting: Clear  
Specifies the second of two names that are allowed to access the objects in the  
FrameSaver unit’s MIB. The community name must be supplied by an external SNMP  
manager whenever the manager tries to access an object in the MIB.  
ASCII text entry – Adds to or changes Community Name 2 (maximum 255 characters).  
Clear – Clears Community Name 2.  
3-88  
December 2002  
9000-A2-GB31-00  
 
                     
3. Configuration Options  
Table 3-33. General SNMP Management Options (2 of 2)  
Name 2 Access  
Possible Settings: Read, Read/Write  
Default Setting: Read  
Specifies the type of access allowed to the objects in the MIB. This is the type of access  
allowed for external SNMP managers accessing MIB objects using Community Name 2.  
Read – Allows read-only access (SNMP Get command). This includes all objects  
specified as either read-only or read/write in the MIB RFCs.  
Read/Write – Allows read and write access (SNMP get and set commands).  
Configuring Telnet and/or FTP Session Support  
Telnet and FTP options control whether a Telnet or FTP (File Transport Protocol)  
session is allowed through an interconnected IP network and the access security  
applicable to the session. Two Telnet sessions can be active at a time (see  
Main MenuConfigurationManagement and Communication→  
Telnet and FTP Session  
When a TS Access Management Link has been set up and activated, the following  
options have no effect upon the PVC:  
n
n
n
Telnet Login Required  
Session Access Level  
FTP Login Required  
9000-A2-GB31-00  
December 2002  
3-89  
 
     
3. Configuration Options  
Table 3-34. Telnet and FTP Session Options (1 of 2)  
Telnet Session  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Specifies whether the FrameSaver unit will respond to a session request from a Telnet  
client on an interconnected IP network.  
Enable – Allows Telnet sessions between the FrameSaver unit and Telnet client.  
Disable – Does not allow Telnet sessions.  
Telnet Login Required  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Specifies whether a user ID and password (referred to as the login) are required to access  
the menu-driven user interface via a Telnet session. If required, the login used is the same  
login used for an menu-driven user interface session. This option does not affect the TS  
Access Management Link.  
Enable – Requires a login to access a Telnet session.  
Disable – Does not require a login.  
Session Access Level  
Possible Settings: Level-1, Level-2, Level-3  
Default Setting: Level-1  
Specifies the highest security level allowed when accessing the menu-driven user  
interface via a Telnet session. If a login is required for the session, the effective access  
level is also determined by the user’s access level. When a login is not required, the  
effective access level is determined by this option. This option does not affect the TS  
Access Management Link.  
NOTE: The effective access level is always the lowest one assigned to either the  
session or the user. For example, if the assigned Session Access Level is Level-2, but  
the User Access Level is Level-3, then only level-3 access is allowed for the session.  
Level-1 – Allows Telnet access by users with Login ID access levels of 1, 2, and 3, with  
the capability to view system information, change configuration options, and run tests.  
This is the highest access level allowed.  
CAUTION: Before changing the session access level to Level-2 or 3, make sure that  
the COM port’s Port Access Level is set to Level-1 and that at least one Login ID is set  
to Level-1. Otherwise, access will be lost. If this occurs, you must reset the unit to the  
factory defaults and begin the configuration process again. A reset is required if the  
Communication Port’s Port Use option is set to Net Link (see Table 3-6, General  
Level-2 – Allows Telnet access by users with Login ID access levels of 1, 2, and 3, with  
the capability to view system information and run tests only; they cannot change  
configuration options.  
Level-3 – Allows Telnet access by users with Login ID access levels of 1, 2, and 3, with  
the capability to view system information only; they cannot change configuration options  
or run tests.  
3-90  
December 2002  
9000-A2-GB31-00  
 
       
3. Configuration Options  
Table 3-34. Telnet and FTP Session Options (2 of 2)  
Inactivity Timeout  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Determines whether a Telnet session is disconnected after a specified period of keyboard  
inactivity.  
Enable Terminates the session after the Disconnect Time expires.  
Disable – Does not terminate Telnet session during inactivity.  
Disconnect Time (Minutes)  
Possible Settings: 1 – 60  
Default Setting: 10  
Sets the amount of keyboard inactive time allowed before a user session is disconnected.  
Display Conditions – This option does not appear when Inactivity Timeout is disabled.  
1 – 60 – Up to an hour can be set.  
FTP Session  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Determines whether the system responds as a server when an FTP (file transfer protocol)  
client on an interconnected IP network requests an FTP session. This option must be  
enabled when downloading files.  
Enable – Allows an FTP session between the system and an FTP client.  
Disable – Does not allow FTP sessions.  
FTP Login Required  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Specifies whether a login ID and password are required for an FTP session. If required,  
the login used is the same login used for a menu-driven user interface session. This  
option does not affect the TS Access Management Link.  
Enable – User is prompted for a login ID and password.  
Disable – No login is required for an FTP session.  
FTP Max Transfer Rate (Kbps)  
Possible Settings: 1 – 1536  
Default Setting: 1536  
Sets the maximum receive (or send) rate of file transfer to the system via management  
PVCs. This option allows new software and configuration files to be downloaded using  
selected bandwidth without interfering with normal operation. Using this option, new  
software and configuration files can be downloaded quickly using the default settings, or  
at a slower rate over an extended period of time by selecting a slower speed. Based upon  
TCP flow control, the FTP server in the system throttles bandwidth to match this setting.  
1 – 1536 – Sets the download line speed from 1 kilobits per second to the maximum  
management speed.  
9000-A2-GB31-00  
December 2002  
3-91  
 
             
3. Configuration Options  
Configuring SNMP NMS Security  
Select SNMP NMS Security from the Management and Communication menu to  
display, add, or change SNMP security configuration options for the FrameSaver  
unit to set up trap managers (see Table 3-35, SNMP NMS Security Options).  
Main MenuConfigurationManagement and CommunicationSNMP  
NMS Security  
A table is displayed consisting of the network management systems identified by  
IP address that are allowed to access the FrameSaver unit by SNMP.  
Table 3-35. SNMP NMS Security Options (1 of 2)  
NMS IP Validation  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Specifies whether security checks are performed on the IP address of SNMP  
management systems attempting to access the node. Only allows access when the  
sending manager’s IP address is listed on the SNMP NMS Security Options screen.  
Enable – Performs security checks.  
Disable – Does not perform security checks.  
Number of Managers  
Possible Settings: 1 – 10  
Default Setting: 1  
Specifies the number of SNMP management systems that are authorized to send SNMP  
messages to the FrameSaver unit. An IP address must be configured for each  
management system allowed to send messages. Configure IP addresses in the NMS n IP  
Address configuration option.  
1 – 10 – Specifies the number of authorized SNMP managers.  
NMS n IP Address  
Possible Settings: 001.000.000.000 – 223.255.255.255, Clear  
Default Setting: Clear (000.000.000.000)  
Provides the IP address of an SNMP manager that is authorized to send SNMP  
messages to the unit. If an SNMP message is received from an unauthorized NMS and its  
IP address cannot be matched here, access is denied and an authenticationFailure trap is  
generated. If a match is found, the type of access (read-only or read/write) is determined  
by the corresponding Access Type.  
Display Conditions – This option appears for each trap manager specified in the  
Number of Trap Managers configuration option.  
001.000.000.000 – 223.255.255.255 – Adds to or changes the NMS IP address.  
Clear – Fills the NMS IP address with zeros.  
3-92  
December 2002  
9000-A2-GB31-00  
 
                         
3. Configuration Options  
Table 3-35. SNMP NMS Security Options (2 of 2)  
Access Type  
Possible Settings: Read, Read/Write  
Default Setting: Read  
Specifies the type of access allowed for an authorized NMS when IP address validation is  
performed.  
Display Conditions – This option appears for each trap manager specified in the  
Number of Trap Managers configuration option.  
Read – Allows read-only access (SNMP Get command) to the MIB objects. This includes  
all objects specified as either read-only or read/write in the MIB RFCs.  
Read/Write – Allows read and write access (SNMP Get and Set commands) to the MIB  
objects. However, access for all read-only objects is specified as read-only.  
Configuring SNMP Traps and Trap Dial-Out  
Select SNMP Traps from the Management and Communication menu to configure  
SNMP traps and dial-out when a trap is generated (see Table 3-36, SNMP Traps  
Main MenuConfigurationManagement and CommunicationSNMP  
Traps  
See the FrameSaver SLV SNMP Reference for trap format standards and special  
trap features, including RMON-specific traps, and the default settings that will  
generate RMON-specific SNMP traps.  
Table 3-36. SNMP Traps and Trap Dial-Out Options (1 of 6)  
SNMP Traps  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Determines whether the FrameSaver unit sends trap messages to the currently  
configured SNMP trap manager(s).  
Enable – Sends trap messages.  
Disable – Does not send trap messages.  
Number of Trap Managers  
Possible Settings: 1 – 6  
Default Setting: 1  
Specifies the number of SNMP management systems that will receive SNMP trap  
messages from the FrameSaver unit. An NMS IP Address must be configured in the NMS  
n IP Address configuration option for each trap manager to receive trap messages.  
1 – 6 – Specifies the number of trap managers (inclusive).  
9000-A2-GB31-00  
December 2002  
3-93  
 
                   
3. Configuration Options  
Table 3-36. SNMP Traps and Trap Dial-Out Options (2 of 6)  
NMS n IP Address  
Possible Settings: 001.000.000.000 – 223.255.255.255, Clear  
Default Setting: Clear (000.000.000.000)  
Specifies the IP address that identifies the SNMP manager(s) to receive SNMP traps.  
Display Conditions – This option appears for each trap manager specified in the  
Number of Trap Managers configuration option.  
001.000.000.000 – 223.255.255.255 – Adds to or changes the IP address for the trap  
manager.  
Clear – Fills the NMS IP address with zeros.  
Initial Route Destination  
Possible Settings: AutoRoute, Modem, COM, Ethernet, PVCname  
Default Setting: AutoRoute  
Specifies the initial route used to reach the specified Trap Manager. When proprietary RIP  
is active, only one unit in the network needs to specify an interface or management link as  
the initial destination. All other units can use the default setting.  
Display Conditions – This option appears for each trap manager specified in the  
Number of Trap Managers configuration option.  
AutoRoute – Uses proprietary RIP from other FrameSaver devices to learn the route for  
sending traps to the specified Trap Manager, or the Default IP Destination when no route  
is available in the routing table (see Table 3-31, Node IP Options).  
Modem – Uses the Modem port. This selection only appears if the Modem Port Use  
configuration option is set to Net Link (see Table 3-39, Modem Port Options).  
COM – Uses the COM port. This selection is only available when Port Use is set to Net  
Ethernet – For the FrameSaver SLV 9126 or 9128, uses the Ethernet port. Only appears  
when the Ethernet port’s Interface Status option is enabled (see Table 3-37, Ethernet  
PVCname – Uses the defined management linkname (the name given the Management  
PVC). This selection only appears when at least one Management PVC is defined for the  
node.  
General Traps  
Possible Settings: Disable, Warm, AuthFail, Both  
Default Setting: Both  
Determines whether SNMP trap messages for warmStart and/or authenticationFailure  
events are sent to the currently configured trap manager(s). An authenticationFailure trap  
indicates that the unit is the addressee of an SNMP protocol message, or an incoming  
ISDN call is not properly authenticated.  
Disable – Does not send trap messages for these events.  
Warm – Sends trap messages for warmStart events only.  
AuthFail – Sends trap messages for authenticationFailure events only.  
Both – Sends trap messages for both warmStart and authenticationFailure events.  
3-94  
December 2002  
9000-A2-GB31-00  
 
                     
3. Configuration Options  
Table 3-36. SNMP Traps and Trap Dial-Out Options (3 of 6)  
Enterprise Specific Traps  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Determines whether trap messages for enterpriseSpecific events are sent to the currently  
configured trap manager(s).  
Enable – Sends trap messages for enterpriseSpecific events.  
Disable – Does not send trap messages for enterpriseSpecific events.  
Link Traps  
Possible Settings: Disable, Up, Down, Both  
Default Setting: Both  
Determines whether SNMP linkDown or linkUp traps are sent to the currently configured  
trap manager(s). A linkDown trap indicates that the unit recognizes a failure in one of the  
interfaces. A linkUp trap indicates that the unit recognizes that one of its interfaces is  
active.  
Use the Link Traps Interface and the DLCI Traps on Interfaces configuration options to  
specify which interface will monitor linkUp and linkDown traps messages.  
Disable – Does not send linkDown or linkUp trap messages.  
Up – Sends trap messages for linkUp events only.  
Down – Sends trap messages for linkDown events only.  
Both – Sends trap messages for linkUp and linkDown events.  
Link Traps Interfaces  
Possible Settings: Network, DSX-1, T1s, Ports, DBM, All  
Default Setting: All  
Specifies which interfaces will generate linkUp, linkDown, and enterpriseSpecific trap  
messages. These traps are not supported on the COM port or Modem port.  
Network – Generates these trap messages on the network interface only.  
DSX-1 – For applicable T1 FrameSaver units, generates these trap messages on the  
DSX-1 interface only.  
T1s – For applicable T1 FrameSaver units, generates these trap messages for linkUp,  
linkDown, and enterpriseSpecific events on both the T1 network and DSX-1 interfaces.  
Ports – Generates these trap messages for linkUp, linkDown, and enterpriseSpecific  
events on a user data port only.  
DBM – For units with an ISDN DBM installed, generates these trap messages for linkUp,  
linkDown, and enterpriseSpecific events on the DBM only.  
All – Generates these trap messages for linkUp and enterpriseSpecific events on all  
interfaces, except for the COM port or modem port, that are applicable to the FrameSaver  
model.  
9000-A2-GB31-00  
December 2002  
3-95  
 
             
3. Configuration Options  
Table 3-36. SNMP Traps and Trap Dial-Out Options (4 of 6)  
DLCI Traps on Interfaces – Interface Selection Field  
Possible Settings: Network, Ports, DBM, All, None  
Default Setting: All  
Specifies which interfaces will generate linkUp and linkDown trap messages for individual  
DLCIs. These traps are only supported on the frame relay interfaces.  
Network – Generates these trap messages on DLCIs for the network interface only.  
Ports – Generates these trap messages for DLCIs on a user data port only.  
DBM – For units with an ISDN DBM installed, generates trap messages on DLCIs for the  
DBM only.  
All – Generates these trap messages on all frame relay interfaces.  
None – No DLCI trap messages are generated.  
DLCI Traps on Interfaces – Filter Selection Field  
Possible Settings: Normal, Filter  
Default Setting: Normal  
Controls whether the traps on the interfaces specified in the DLCI Traps on Interfaces  
configuration option are sent regardless of their cause.  
Normal – Generates trap messages specified by DLCI Traps on Interfaces regardless of  
cause.  
Filter – Prevents traps from being generated for the interfaces specified by DLCI Traps on  
Interfaces if their cause is the loss of the interface connection or LMI.  
RMON Traps  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Specifies whether remote monitoring traps are sent to the currently configured trap  
manager(s). RMON traps are typically sent as a result of the Alarms and Events Groups  
of RMON1 when a selected variable’s configured threshold is exceeded.  
Enable – Sends trap messages when set thresholds are exceeded.  
Disable – Does not send trap messages when set thresholds are exceeded.  
ISDN Dial Control Traps  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Controls whether dialCtlPeerCallSetup and dialCtlPeerCallInformation events send trap  
messages to the currently configured SNMP trap manager(s). Use this feature when  
peer-to-peer (nearest neighbor) calling is desired.  
Display Conditions – This option only appears when an ISDN DBM is installed.  
Enable – Sends trap messages.  
Disable – Does not send trap messages.  
3-96  
December 2002  
9000-A2-GB31-00  
 
       
3. Configuration Options  
Table 3-36. SNMP Traps and Trap Dial-Out Options (5 of 6)  
Trap Dial-Out  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Controls whether SNMP trap messages initiate a call automatically. If the call cannot be  
completed and the Call Retry option is set to Enable, the SNMP trap message is held  
(queued) until the call completes to either the Alarm or alternate directory.  
NOTE: When the modem port is configured as a network communication link, up to 10  
SNMP trap messages are held at the port.  
Enable – Automatically calls the phone number contained in the Control menu’s Modem  
Call Directories, Directory Number A (Alarm).  
Disable – Automatic calls will not be initiated. Traps sent to the modem are held until a  
dial-in connection is established.  
Trap Disconnect  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Determines whether the internal modem disconnects after the SNMP trap message has  
been sent. This configuration option only applies to modem connections initiated as a  
result of sending the SNMP trap message.  
Enable – Disconnects the call after sending an SNMP trap message(s).  
Disable – Does not disconnect the call and holds the line until it is disconnected manually  
or by the remote modem. This allows the NMS to poll the FrameSaver unit for more  
information after receiving an SNMP trap.  
Call Retry  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Controls whether an incomplete call (busy, no answer, etc.) is retried when an SNMP trap  
message is sent to the modem port.  
If an Alternate Dial-Out Directory is specified, the alarm directory’s telephone number is  
called first. If the call cannot be completed, then the alternate directory’s telephone  
number is called (see the Control menu’s Modem Call Directories).  
Enable – Attempts to retry the call, up to one time per SNMP trap message, with a delay  
between the retry. The delay is specified by the Dial-Out Delay Time (Min) configuration  
option.  
Disable – Does not retry an incomplete call.  
Dial-Out Delay TIme (Min)  
Possible Settings: 1 – 10  
Default Setting: 5  
Specifies the amount of time between call retries when an SNMP trap message is sent;  
the wait between call attempts (see the Call Retry option).  
1 – 10 – Sets the number of minutes for the delay between call retry attempts.  
9000-A2-GB31-00  
December 2002  
3-97  
 
         
3. Configuration Options  
Table 3-36. SNMP Traps and Trap Dial-Out Options (6 of 6)  
Alternate Dial-Out Directory  
Possible Settings: None, 1 – 5  
Default Setting: None  
Specifies whether an incomplete call (busy, or no answer, etc.) resulting from an attempt  
to send an SNMP trap message is retried using an alternate telephone number. Up to  
5 alternate call directories can be set up, but only one at a time can be used.  
When Call Retry is enabled, the alarm directory’s telephone number is called first. If the  
call cannot be completed after one additional try, then the specified alternate directory’s  
telephone number is called.  
None – Does not dial-out using one of the alternate directory telephone numbers.  
1 – 5 – Specifies the call directory containing the telephone number to call if a call cannot  
be completed using the telephone number in the alarm directory (Directory Number A in  
the Control menu’s Modem Call Directories), inclusive.  
Latency Traps  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Determines whether a Latency Threshold Alarm causes the generation of a Latency  
Threshold Exceeded Trap.  
Enable – Sends trap messages for Latency Threshold Alarm events.  
Disable – Does not send trap messages for Latency Threshold Alarm events.  
IP SLV Availability Traps  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Determines whether a Path Unavailability condition causes the generation of an IP SLV  
Availability Trap.  
Enable – Sends trap messages for Path Unavailability events.  
Disable – Does not send trap messages for Path Unavailability events.  
3-98  
December 2002  
9000-A2-GB31-00  
 
         
3. Configuration Options  
Configuring Ethernet Management  
Select Ethernet Management from the Management and Communication menu, or  
Ethernet Management Options Screen from the Easy Install screen, to configure  
the Ethernet port (see Table 3-37, Ethernet Management Options).  
Main MenuConfigurationManagement and Communication→  
Ethernet Management  
Main MenuEasy InstallEthernet Management Options Screen  
Table 3-37. Ethernet Management Options (1 of 2)  
Interface Status  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Determines whether the Ethernet port is being used and can be configured.  
Enable – The port is active. It can receive Version 2 or IEEE 802.3 MAC frames and  
transmit Version 2 MAC frames only. When the Ethernet port is enabled, the Would you  
like to set the Node’s IP Destination to Ethernet?prompt is displayed.  
If you select Yes, the Default IP Destination (see Table 3-31, Node IP Options) is  
automatically changed to Ethernet, so the Ethernet port’s Default Gateway Address  
is used for packets that do not have a route. This is required when the NMS is on a  
different subnet than the unit.  
If you select No, the COM port or a PVC will be used for packets without a route.  
Disable – The port is not active. When the port is disabled, the following will occur:  
No alarms or traps configured for the port will be generated.  
All port uses that refer to the Ethernet port, like the Default IP Destination and Initial  
Route Destination, will be reset to their default values (see Table 3-31, Node IP  
IP Address  
Possible Settings: 001.000.000.000 – 223.255.255.255, Clear  
Default Setting: Clear (000.000.000.000)  
Specifies the IP address needed to access the Ethernet port.  
001.000.000.000 – 223.255.255.255 – Shows the IP address for the port, which can be  
viewed or edited.  
Clear – Fills the IP address with zeros.  
Subnet Mask  
Possible Settings: 000.000.000.000 – 255.255.255.255, Clear  
Default Setting: 000.000.000.000  
Specifies the subnet mask associated with the IP address that is needed to access the  
Ethernet port.  
000.000.000.000 – 255.255.255.255 – Set the Ethernet port’s subnet mask. The range for  
each byte is 000 to 255.  
Clear – Fills the subnet mask associated with the IP address with zeros.  
9000-A2-GB31-00  
December 2002  
3-99  
 
         
3. Configuration Options  
Table 3-37. Ethernet Management Options (2 of 2)  
Default Gateway Address  
Possible Settings: 001.000.000.000 – 223.255.255.255, Clear  
Default Setting: Clear (000.000.000.000)  
Specifies the IP address for the port’s default gateway. It is used for packets that do not  
have a route.  
001.000.000.000 – 223.255.255.255 – Shows the IP address for the port, which can be  
viewed or edited (i.e., a router on the LAN).  
Clear – Fills the default gateway’s IP address with zeros.  
Proxy ARP  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Determines whether the FrameSaver unit will use the Proxy ARP (Address Resolution  
Protocol) technique, acting as the gateway to other FrameSaver devices in its  
management network when there is an ARP request for a device not on the Ethernet.  
Enable – Proxy ARP is enabled on the port so the FrameSaver unit will act as an agent  
for or gateway to other units in its management network. Using this technique, the  
FrameSaver unit returns its own MAC (Media Access Control) address in response to  
ARP requests when it recognizes that the destination IP address is in its subnet, but the  
device sending the ARP request is in another network. Packets sent to the FrameSaver  
unit’s gateway address are forwarded to the appropriate device.  
Disable – The Proxy ARP technique will not be used by the unit; it will not act as an agent  
for other devices in its network.  
3-100  
December 2002  
9000-A2-GB31-00  
 
         
3. Configuration Options  
Configuring the Communication Port  
Select Communication Port from the Management and Communication menu to  
display or change the communication port configuration options (see Table 3-38,  
Main MenuConfigurationManagement and Communication→  
Communication Port  
Table 3-38. Communication Port Options (1 of 5)  
Port Use  
Possible Settings: Terminal, Net Link, Modem PassThru  
Default Setting: Terminal  
Assigns a specific use to the COM port.  
NOTE: If the Default IP Destination is set to COM (see Table 3-31, Node IP Options)  
and you change Port Use to Terminal, the Default IP Destination is forced to None.  
Terminal – The COM port is used for the asynchronous terminal connection.  
Net Link – The COM port is the network communications link to the IP network or IP  
device port. You cannot change Port Use to Net Link when the Modem PassThru feature  
is enabled. When you try, the Cannot change Port Use – Modem PassThru is  
enabledmessage is displayed.  
Modem PassThru – Available to the FrameSaver SLV 9626 only, the COM port is  
connected to the router’s auxiliary (AUX) or console port so the router can be accessed  
via a dial-up connection to the unit. When this feature is active, a logical connection  
between the unit’s modem and COM ports is made, and data received over the modem  
port is transmitted out the COM port to the router’s AUX or console port. When an escape  
sequence (minus, minus, minus, with a minimum of 50 ms between each) is detected, the  
FrameSaver unit switches back to normal user interface operation.  
Data Rate (Kbps)  
Possible Settings: 9.6, 14.4, 19.2, 28.8, 38.4, 57.6, 115.2  
Default Setting: 19.2  
Specifies the rate for the COM port in kilobits per second.  
9.6 – 115.2 Kbps – Sets the communication port speed.  
Character Length  
Possible Settings: 7, 8  
Default Setting: 8  
Specifies the number of bits needed to represent one character.  
NOTE: Character length defaults to 8 and cannot be changed if Port Use is set to Net  
Link.  
7 – Sets the character length to seven bits.  
8 – Sets the character length to eight bits. Use this setting if using the COM port as the  
network communication link.  
9000-A2-GB31-00  
December 2002  
3-101  
 
                   
3. Configuration Options  
Table 3-38. Communication Port Options (2 of 5)  
Parity  
Possible Settings: None, Even, Odd  
Default Setting: None  
Provides a method of checking the accuracy of binary numbers for the COM port. A parity  
bit is added to the data to make the “1” bits of each character add up to either an odd or  
even number. Each character of transmitted data is approved as error-free if the “1” bits  
add up to an odd or even number as specified by this configuration option.  
None – Provides no parity.  
Even – Makes the sum of all 1 bits and its corresponding parity bit always even.  
Odd – Makes the sum of all 1 bits and its corresponding parity bit always odd.  
Stop Bits  
Possible Settings: 1, 2  
Default Setting: 1  
Determines the number of stop bits used for the COM port.  
1 – Provides one stop bit.  
2 – Provides two stop bits.  
Ignore Control Leads  
Possible Settings: Disable, DTR  
Default Setting: Disable  
Specifies whether DTR is used.  
Display Conditions – This option does not apply to the FrameSaver SLV Router.  
Disable – Treats control leads as standard operation.  
DTR – Ignores DTR. This may be necessary when connecting to some PAD devices.  
Login Required  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Determines whether a user ID and password (referred to as the login) is required in order  
to log on to the asynchronous terminal connected to the COM port.  
Display Conditions – This option only appears when Port Use is set to Terminal.  
Enable – Requires a login to access the menu-driven user interface.  
Disable – Does not requires a login.  
3-102  
December 2002  
9000-A2-GB31-00  
 
             
3. Configuration Options  
Table 3-38. Communication Port Options (3 of 5)  
Port Access Level  
Possible Settings: Level-1, Level-2, Level-3  
Default Setting: Level-1  
Specifies level of user access privilege for an asynchronous terminal connected to the  
COM port. If a login is required for the port, the effective access level is determined by the  
user’s access level. When a login is not required, the effective access level is determined  
by this option.  
NOTE: The effective access level is always the lowest one assigned to either the port  
or the user. For example, if the Port Access Level assigned is Level-2, but the User  
Access Level is Level-3, then only level-3 access will be permitted for the port.  
Display Conditions – This option only appears when Port Use is set to Terminal.  
Level-1 – Allows full access and control of the device including monitoring, diagnostics,  
and configuration. The user can add, change, and display configuration options, and  
perform device testing.  
CAUTION: Before changing the communication port’s access level to Level-2 or 3,  
make sure that either Telnet Session Access Level or the Modem Port’s Port Access  
Level is set top Level-1 and at least one Login ID is set to Level-1. Otherwise, access  
will be lost. If this occurs, you must reset the unit to the factory defaults and begin the  
configuration process again.  
Level-2 – Allows limited access and control of the device. The user can monitor and  
perform diagnostics, display status and configuration option information.  
Level-3 – Allows limited access with monitoring control only. The user can monitor and  
display status and configuration screens only.  
Inactivity Timeout  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Determines whether a user session is disconnected after a specified time of inactivity (no  
keyboard activity).  
Display Conditions – This option only appears when Port Use is set to Terminal.  
Enable – Disconnects user session after the specified time of inactivity.  
Disable – Does not disconnect user session.  
Disconnect Time (Minutes)  
Possible Settings: 1 – 60  
Default Setting: 10  
Specifies the number of minutes of inactivity that can elapse before the session is  
disconnected.  
Display Conditions – This option only appears when Port Use is set to Terminal.  
1 – 60 – Sets the time from 1 to 60 minutes (inclusive).  
9000-A2-GB31-00  
December 2002  
3-103  
 
         
3. Configuration Options  
Table 3-38. Communication Port Options (4 of 5)  
IP Address  
Possible Settings: 001.000.000.000 – 223.255.255.255, Clear  
Default Setting: Clear (000.000.000.000)  
Specifies a unique IP address for accessing the unit via the COM port. Only in effect when  
the COM port is configured as a network communication link (Port Use option is set to Net  
Link).  
Display Conditions – This option only appears when Port Use is set to Net Link.  
001.000.000.000 – 223.255.255.255 – Shows the IP address for the COM port, which you  
can view or edit.  
Clear – Clears the IP address for the COM port and fills the address with zeros. When the  
IP Address is all zeros, the COM port uses the Node IP Address if one has been  
configured.  
Subnet Mask  
Possible Settings: 000.000.000.000 – 255.255.255.255, Clear  
Default Setting: 000.000.000.000  
Specifies the subnet mask needed to access the unit. Only in effect when the COM port is  
configured as a network communication link (Port Use option is set to Net Link).  
Display Conditions – This option only appears when Port Use is set to Net Link.  
000.000.000.000 – 255.255.255.255 – Shows the subnet mask for the COM port, which  
you can view or edit.  
Clear – Clears the subnet mask for the COM port and fills the address with zeros. When  
the node subnet mask is all zeros, the IP protocol creates a default subnet mask based  
upon the class of the IP address: Class A: 255.000.000.000, Class B: 255.255.000.000, or  
Class C: 255.255.255.000.  
RIP  
Possible Settings: None, Standard_out  
Default Setting: None  
Specifies which Routing Information Protocol (RIP) is used to enable routing of  
management data between devices.  
Display Conditions – This option only appears when Port Use is set to Net Link.  
None – No routing is used.  
Standard_out – The device will send standard RIP messages to communicate routing  
information about other FrameSaver units in the network. Standard RIP messages  
received on this link are ignored.  
NOTE: The router must be configured to receive RIP on the port connected to the  
COM port, configured as the management interface (e.g., Cisco: config-t, router  
RIP, int serialx, IP RIP Receive version 1, ctl-z WR).  
To create this management interface, make sure that Node or COM port IP Information  
3-104  
December 2002  
9000-A2-GB31-00  
 
         
3. Configuration Options  
Table 3-38. Communication Port Options (5 of 5)  
Link Protocol  
Possible Settings: PPP, SLIP  
Default Setting: PPP  
Specifies the link-layer protocol to be used. Only in effect when the COM port is  
configured as a network communication link (Port Use option is set to Net Link).  
Display Conditions – This option only appears when Port Use is set to Net Link.  
PPP – Point-to-Point Protocol.  
SLIP – Serial-Line Internet Protocol.  
Configuring the Modem Port  
Select Modem Port from the Management and Communication menu to configure  
the modem port (seeTable 3-39, Modem Port Options).  
Main MenuConfigurationManagement and Communication→  
Modem Port  
Table 3-39. Modem Port Options (1 of 4)  
Port Use  
Possible Settings: Terminal, Net Link  
Default Setting: Terminal  
Assigns a specific use to the modem port.  
NOTE: If the Default IP Destination is set to Modem (see Table 3-31, Node IP Options)  
and you change Port Use to Terminal, the Default IP Destination is forced to None.  
Terminal – The modem port is used for the asynchronous terminal connection.  
Net Link – The modem port is a network communications link to the IP network. You  
cannot change Port Use to Net Link when the Modem PassThru feature is enabled. When  
you try, the Cannot change Port Use – Modem PassThru is enabledmessage  
is displayed. See the FrameSaver SLV Operations Guide for more information about  
Modem PassThru operation.  
Dial-In Access  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Controls whether external devices can dial-in to the system through the internal modem.  
This allows dial-in access by a remote terminal when Port Use is set to Terminal. When  
Port Use is set to Net Link, Dial-In Access must be set to Enable to allow an external NMS  
to dial in to the device.  
Enable – Dial-in access is allowed. Incoming calls are answered.  
Disable – Dial-in access is not allowed. Incoming calls are not answered. You cannot  
disable Dial-In Access when the Modem PassThru feature is enabled. When you try, the  
Cannot change Dial-In Access when Modem PassThru is enabledmessage  
is displayed. See the FrameSaver SLV Operations Guide for more information about  
Modem PassThru operation.  
9000-A2-GB31-00  
December 2002  
3-105  
 
                               
3. Configuration Options  
Table 3-39. Modem Port Options (2 of 4)  
Login Required  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Determines whether a user ID and password (referred to as the login) is required in order  
to log on to the asynchronous terminal connected to the modem port.  
Display Conditions – This option only appears when Port Use is set to Terminal.  
Enable – Requires a login to access the menu-driven user interface.  
Disable – Does not require a login.  
Port Access Level  
Possible Settings: Level-1, Level-2, Level-3  
Default Setting: Level-1  
Specifies the level of user access privilege for an asynchronous terminal connected to the  
modem port.  
NOTE: The effective access level is always the lowest one assigned to either the port  
or the user. For example, if the Port Access Level assigned is Level-2, but the User  
Access Level is Level-3, then only Level-3 access will be permitted for the modem port.  
Display Conditions – This option only appears when Port Use is set to Terminal.  
Level-1 – Allows full access and control of the device including monitoring, diagnostics,  
and configuration. The user can add, change, and display configuration options, save,  
and perform device testing. If Login Required is set to Enable, the effective access level is  
determined by the user’s access level. Otherwise, the access level is 1.  
CAUTION: Before changing the modem port’s access level to Level-2 or 3, make sure  
that either Telnet Session Access Level or the communications port’s Port Access  
Level is set to Level-1 and at least one Login ID are set to Level-1. Otherwise, access  
will be lost. If this occurs, you must reset the unit to the factory defaults and begin the  
configuration process again.  
Level-2 – Allows limited access and control of the device. The user can monitor and  
perform diagnostics, display status and configuration option information. If Login Required  
is set to Enable, the effective access level is 2 for User ID access levels of 1 or 2. User IDs  
set to access Level-3 have only Level-3 access.  
Level-3 – Allows limited access with monitoring control only. The user can only display  
and monitor status and configuration screens. If Login Required is set to Enable, the  
effective access level is 3 for all user IDs.  
Inactivity Timeout  
Possible Settings: Enable, Disable  
Default Setting: Enable  
Determines whether a user session is disconnected after a specified time of inactivity (no  
keyboard activity).  
Display Conditions – This option only appears when Port Use is set to Terminal.  
Enable – Disconnects the user session after the specified time of inactivity.  
Disable – Does not disconnect the user session.  
3-106  
December 2002  
9000-A2-GB31-00  
 
         
3. Configuration Options  
Table 3-39. Modem Port Options (3 of 4)  
Disconnect Time (Minutes)  
Possible Settings: 1 – 60  
Default Setting: 10  
Determines the amount of lapsed time before disconnecting a user session in minutes.  
Display Conditions – This option only appears when:  
Port Use is set to Terminal.  
Inactivity Timeout is set to Enable.  
1 – 60 – Sets the number of minutes allowed before the modem disconnects.  
IP Address  
Possible Settings: 001.000.000.000 – 223.255.255.255, Clear  
Default Setting: Clear (000.000.000.000)  
Specifies a unique IP address for accessing the system via the modem port. This option is  
only in effect when the modem port is configured as a network communication link.  
Display Conditions – This option only appears when Port Use is set to Net Link.  
001.000.000.000 – 223.255.255.255 – Shows the IP address for the modem port, which  
you can view or edit.  
Clear – Clears the IP address for the modem port and fills the address with zeros (i.e.,  
000.000.000.000). When the IP Address is all zeros, the modem port uses the Node IP  
Address if one has been configured.  
Subnet Mask  
Possible Settings: 000.000.000.000 – 255.255.255.255, Clear  
Default Setting: 000.000.000.000  
Specifies the subnet mask needed to access the system. This option is only in effect when  
the modem port is configured as a network communication link.  
Display Conditions – This option only appears when Port Use is set to Net Link.  
000.000.000.000 – 255.255.255.255 – Shows the subnet mask for the modem port, which  
you can view or edit.  
Clear – Clears the subnet mask for the COM port and fills the address with zeros. When  
the node subnet mask is all zeros, the IP protocol creates a default subnet mask based  
upon the class of the IP address: Class A: 255.000.000.000, Class B: 255.255.000.000, or  
Class C: 255.255.255.000.  
Link Protocol  
Possible Settings: PPP, SLIP  
Default Setting: PPP  
Specifies the link-layer protocol to be used. This option is only in effect when the modem  
port is configured as a network communication link.  
Display Conditions – This option only appears when Port Use is set to Net Link.  
PPP – Point-to-Point Protocol.  
SLIP – Serial-Line Internet Protocol.  
9000-A2-GB31-00  
December 2002  
3-107  
 
                 
3. Configuration Options  
Table 3-39. Modem Port Options (4 of 4)  
Alternate IP Address  
Possible Settings: 001.000.000.000 – 223.255.255.255, Clear  
Default Setting: Clear (000.000.000.000)  
Specifies the alternate IP address for the modem port. If this configuration option is not  
configured (i.e., it is zero), the modem port’s primary IP address is used when the  
alternate telephone directory is used for dial-out traps.  
Display Conditions – This option only appears when Port Use is set to Net Link.  
001.000.000.000 – 223.255.255.255 – Shows the modem’s alternate IP address, which  
you can view or edit.  
Clear – Clears the alternate IP address for the modem port and fills the address with  
zeros.  
Alternate Subnet Mask  
Possible Settings: 000.000.000.000 – 255.255.255.255, Clear  
Default Setting: 000.000.000.000  
Specifies the alternate subnet mask needed to access the unit. Only in effect when the  
modem port is configured as a network communication link.  
Display Conditions – This option only appears when Port Use is set to Net Link.  
000.000.000.000 – 255.255.255.255 – Shows the subnet mask for the modem port, which  
you can view or edit.  
Clear – Clears the subnet mask for the modem port and fills the address with zeros.  
When the node subnet mask is all zeros, the IP protocol creates a default subnet mask  
based upon the class of the IP address: Class A: 255.000.000.000, Class B:  
255.255.000.000, or Class C: 255.255.255.000.  
3-108  
December 2002  
9000-A2-GB31-00  
 
       
3. Configuration Options  
Configuring the Criteria for Automatic Backup  
For units with an ISDN DBM, follow this menu selection sequence to specify  
whether and when automatic backup is allowed, and to configure timers that will  
control and terminate backup, or set delays (see Table 3-40, Auto Backup Criteria  
Options).  
Main MenuConfigurationAuto Backup Criteria  
Table 3-40. Auto Backup Criteria Options (1 of 2)  
Auto Backup  
Possible Settings: Enable, Disable  
Default Setting: Disable  
Determines whether backup for the access unit is automatically performed when the  
primary physical link or LMI, or a DLCI on a PVC connection fails, or when latency is  
exceeded.  
When enabled, the access unit automatically enables the Alternate Link configuration  
option, and establishes an alternate DLCI and EDLCI, rerouting traffic over the backup  
interface. (See Table 3-32, Management PVC Options, to configure the alternate DLCI  
and alternate EDLCI.)  
NOTE: Auto Backup cannot be enabled unless LMI Behavior is set to Independent  
Enable – Reroutes traffic over the backup (alternate) interface.  
Disable – Does not reroute traffic over the backup interface.  
DLCI Down Backup Activation Delay (sec)  
Possible Settings: 0 – 3600  
Default Setting: 0  
Specifies the number of seconds the unit will wait once a DLCI is declared down before it  
initiates backup. A DLCI is declared down when the DLCI changes to Inactive status in an  
LMI response, or when there is an LMI or physical link failure. When a delay is configured,  
the unit is more tolerant of network glitches, or repeated short outages, before going into  
backup, minimizing bouncing between network and backup services.  
0 – 3600 – Specifies the amount of time for the delay.  
DLCI Down Backup Activation Transition Threshold  
Possible Settings: 1 – 10  
Default Setting: 1  
Specifies how many times a primary destination DLCI transitions up or down during the  
DLCI Down Backup Activation Delay period before the unit initiates backup, provided the  
DLCI is active when the delay period ends.  
1 – 10 – Specifies the number of transitions allowed between Active and Inactive status.  
Backup Restoration Delay (sec)  
Possible Settings: 0 – 3600  
Default Setting: 0  
Specifies the number of seconds the unit will wait after all backup alarm conditions have  
cleared for a primary destination DLCI before the backup connection is terminated.  
0 – 3600 – Specifies the amount of time for the delay.  
9000-A2-GB31-00  
December 2002  
3-109  
 
           
3. Configuration Options  
Table 3-40. Auto Backup Criteria Options (2 of 2)  
When Auto Backup Allowed  
Possible Settings: Always, Restrict  
Default Setting: Always  
Determines when backup for the access unit is allowed to occur.  
Always – No restrictions on backup.  
Restrict – Backup is restricted to the day and time selected in the following configuration  
options. Use this selection when the importance of the data that you are backing up is  
day/time dependent.  
Backup Allowed: Day From nn:nn  
Possible Settings: 00:00 – 23:00, None  
Default Setting: 00:00  
Specifies the time that Auto Backup can begin for a selected day of the week in  
increments of 1 hour. Day is Monday through Sunday.  
00:00 – 23:00 – Specifies the time of day that Auto Backup will start for this particular day.  
None – Auto Backup cannot occur on this day.  
Backup Allowed: Day To nn:nn  
Possible Settings: 00:00 – 24:00  
Default Setting: 24:00  
Specifies the time that Auto Backup must end occurring for the selected day of the week  
in increments of 1 hour.  
Display Conditions – This option only appears if a start time was specified.  
00:00 – 24:00 – Specifies the time of day that Auto Backup will stop for this particular day.  
3-110  
December 2002  
9000-A2-GB31-00  
 
4. Feature-Specific Configuration  
Setting Up an External Modem  
A standard EIA-232-D crossover cable can be used to connect the COM port to an  
external modem. The external modem must be configured so it is compatible with  
the FrameSaver unit.  
Procedure  
To configure an external modem:  
1. Connect the crossover cable to the external modem.  
2. Enable auto-answer on your modem, and configure it to use the following  
LSD, DSR, CTS, RTS, and DTR control leads.  
See the table below for AT D0 command strings. Use the following command  
string:  
AT &C0 &D2 &S0 &R1 \D0 S0=1  
AT Command String  
To configure the modem to . . .  
Force LSD on.  
&C0  
&D2  
&S0  
&R1  
\D0  
Drop the connection when the unit drops DTR.  
Force DSR on.  
Ignore RTS.  
Force CTS on.  
S0=1  
Automatically answer incoming calls.  
4-2  
December 2002  
9000-A2-GB31-00  
 
 
4. Feature-Specific Configuration  
Setting Up an Internal Modem  
Models 9126, 9128, 9520, 9520-ILM, 9626, and 9820-45M have an internal  
modem for dial-in access to the menu-driven user interface, as well as dial-out  
capability when an SNMP trap is generated. When the modem will be used to dial  
out, Modem Directory phone numbers need to be set up. Otherwise, simply  
configure or change dial-in access to the unit.  
The modem port is already configured for connection to an asynchronous terminal  
and dial-in access, with Port Use set to Terminal. However, additional changes  
Options).  
Main MenuConfigurationManagement and Communication→  
Modem Port  
For dial-in access to the menu-driven user interface via Telnet, make sure Port  
Use is set to Net Link, the IP address and subnet mask are entered if they are  
different from the node’s, and that the Link Protocol is correct.  
For dial-in access to the router connected to the unit’s COM port, make sure the  
Communication Port’s Port Use option is set to Modem PassThru.  
feature is desired. See the FrameSaver SLV Operations Guide for additional  
information.  
Setting Up Call Directories for Trap Dial-Out  
Procedure  
1. Set up directory phone numbers.  
Main MenuControlModem Call Directories  
2. Select Directory Number A (for Alarm).  
3. Enter the phone number(s).  
Valid characters include . . . For . . .  
ASCII text  
Entering the phone number.  
Readability characters.  
Space,  
underscore (_), and dash (–)  
Comma (,)  
Readability character for a 2-second pause.  
Blind dialing.  
B
P
T
Pulse dialing, unless B is specified.  
Tone dialing, unless B is specified.  
Wait for dial tone.  
W
9000-A2-GB31-00  
December 2002  
4-3  
 
             
4. Feature-Specific Configuration  
4. Save the phone number(s).  
Setting Up to Use the Modem PassThru Feature  
Dial-in access to the router is possible via the Modem PassThru feature, also  
known as the Router Assist feature. The FrameSaver unit’s COM port must be  
connected to the router’s auxiliary (AUX) or console port, and the COM port must  
be configured for this use.  
When this feature is set up and active, a logical connection between the unit’s  
modem and COM ports is made, and data received over the modem port is  
transmitted out the COM port to the router’s AUX or console port. When an escape  
sequence (minus, minus, minus, with a minimum of 50 ms between each) is  
detected, the FrameSaver unit switches back to normal user interface operation.  
See the FrameSaver SLV Technical Description for cable information.  
Procedure  
1. Configure the COM port to use Modem PassThru.  
Main MenuConfigurationManagement and Communication→  
Communication Port  
2. Set Port Use to Modem PassThru.  
3. Save the configuration.  
4-4  
December 2002  
9000-A2-GB31-00  
 
     
4. Feature-Specific Configuration  
Setting Up Dial Backup  
When configuring units with ISDN backup capability, the following guidelines  
apply:  
n
Central site configuration guidelines:  
— Set up the ISDN DBM physical interface.  
— If a BRI DBM, change the Automatic Backup Configuration to  
Multi_Site_Backup. (A PRI DBM is already configured for multisite  
backup.)  
— Modify the Link Profile(s) that Automatic Backup Configuration created to  
add a phone number.  
n
Remote site configuration guidelines:  
— Set up the ISDN DBM physical interface.  
— If a PRI DBM, change the Automatic Backup Configuration to  
Single_Site_Backup. (A BRI DBM is already configured for single-site  
backup.)  
— Modify the HQ_Site Link Profile that Automatic Backup Configuration  
created to add a phone number.  
— Set the criteria by which automatic backup will take place.  
Setting Up the DBM Physical Interface  
Procedure  
1. Configure the DBM interface.  
Main MenuConfigurationISDNPhysical  
2. Enable the interface, and enter the Service Profile IDs (SPIDs) and local  
phone numbers.  
3. Save the configuration.  
Configuration Options, for configuration information.  
9000-A2-GB31-00  
December 2002  
4-5  
 
         
4. Feature-Specific Configuration  
Setting Up Automatic Backup Configuration  
The Automatic Backup Configuration feature is used to automatically create  
alternate DLCI records and PVC connections on the ISDN DBM (backup) interface  
for current or newly discovered PVC Connections and Management PVCs.  
This feature is already set up, with Single_Site_Backup as the default for units with  
a BRI DBM and Multi_Site_Backup for units with a PRI DBM. If the unit at the  
central site has a BRI DBM, change the Automatic Backup Configuration to  
Multi_Site_Backup, if necessary.  
Main MenuAuto-ConfigurationAutomatic Backup Configuration  
If you select . . .  
Then . . .  
Single_Site_Backup  
Alternate destinations are automatically configured using a  
single ISDN Link Profile to backup all network PVC  
Connections and Management PVCs over the primary  
destination ISDN link.  
(default for a BRI DBM)  
(Used at remote sites since  
only one ISDN link to the  
central-site is needed.)  
Initially, PVCs with alternate destinations are configured on  
the first ISDN Link Profile using the same DLCI number as  
the network DLCI being backed up. However, primary  
destination PVCs on the ISDN DBM interface are  
automatically updated to use a different DLCI number for  
the alternate destination DLCI, derived from the first SLV  
message received on the each network DLCI.  
Multi_Site_Backup  
Alternate destinations are automatically configured using a  
separate ISDN Link Profile to backup each network PVC  
Connection and Management PVC over the ISDN interface.  
(default for a PRI DBM)  
(Used at central sites since  
multiple ISDN links are  
needed, one for each  
remote-site.)  
Initially, all DLCIs are configured on the ISDN links using  
the same DLCI number as the network DLCI being backed  
up. However, primary destination PVCs on the ISDN DBM  
interface are automatically updated to use a different DLCI  
number for the alternate destination DLCI, derived from the  
first SLV message received on the each network DLCI.  
Automatically created alternate destination Link Profiles  
appear as Bkupnnnn, nnnn being the DLCI number (e.g.,  
Bkup200 would be configured for network DLCI 200).  
Disabled  
No automatic configuration takes place on the DBM  
interface and no alternate destinations are created for  
PVCs.  
NOTE:  
Changes must be saved to take effect.  
screen example.  
4-6  
December 2002  
9000-A2-GB31-00  
 
   
4. Feature-Specific Configuration  
When the Automatic Backup Configuration setting is changed, the following  
prompts appear. No is the default for these prompts.  
The following prompt  
When the . . .  
appears . . .  
If you select . . .  
Automatic Backup  
Configuration setting Auto-Configuration  
was changed, and  
Saving will cause  
No – No Auto-Configuration  
updates are performed and  
updates due to LMI response  
messages are performed  
according to the previously  
saved setting.  
to update and  
Restart. Are you  
sure?  
Save was selected  
Yes – The Delete All  
DLCIs and PVC  
Connections?prompt  
appears.  
Response to the  
Delete All DLCIs Alternate  
and PVC  
Connections?  
prompt was No, and  
Delete All  
No – No previously configured  
DLCIs or PVC connections are  
removed or changed, and  
newly discovered DLCIs will be  
configured according to the  
new discovery mode and  
Destinations from  
PVC Connections?  
Automatic Backup  
Configuration was  
disabled  
automatic backup setting.  
Yes – All multiplexed DLCIs,  
ISDN Link Profiles (except for  
the first one), and PVC  
connections are deleted,  
except for management PVCs  
with the user data port as the  
primary destination and  
managementPVCs designated  
as the TS Management Link.  
If an alternate destination has  
been configured on a retained  
Management PVC, the  
alternate destination will be  
deleted but the primary  
destination will be retained.  
Response to the  
Delete All DLCIs Destinations to  
and PVC  
Connections?  
prompt was No, and  
Add Alternate  
Yes – DLCI records are  
configured on the ISDN link(s)  
and Alternate Destination  
information is added to current  
PVC connections and  
Current PVC  
Connections?  
management PVCs.  
Automatic Backup  
Configuration was set  
to  
Single_Site_Backup  
or Multi_Site_Backup  
No – No previously configured  
PVC connections are changed,  
and newly discovered DLCIs  
will be configured according to  
the new discovery mode and  
automatic backup setting.  
9000-A2-GB31-00  
December 2002  
4-7  
 
   
4. Feature-Specific Configuration  
The following prompt  
appears . . .  
When the . . .  
If you select . . .  
Response to the  
Remove Alternate  
Destinations  
from PVCs and  
delete unused  
DLCI Records?  
prompt was Yes, and  
No – No previously configured  
DLCIs, ISDN Link Profiles, or  
PVC Connections are removed  
or changed, but updates due to  
LMI responses will be  
performed using the new  
setting.  
Automatic Backup  
Configuration was  
disabled  
Yes – All Alternate Destination  
information will be removed  
from PVC Connections and  
Management PVCs, and all  
DLCIs and ISDN Link Profiles  
(except for the first one) used  
exclusively as Alternate  
Destinations are deleted.  
Response to the  
Remove Alternate Destinations to  
Destinations  
from PVCs and  
delete unused  
DLCI Records?  
prompt was Yes, and  
Add Alternate  
No – No previously configured  
PVC Connections are removed  
or changed, but updates due to  
LMI responses will be  
performed using the new  
setting.  
Current PVC  
Connections?  
Yes – Alternate Destination  
information is configured for  
current DLCIs, ISDN Link  
Profiles, PVC Connections and  
Management PVCs on the  
ISDN DBM interface, except for  
the Management PVC  
Automatic Backup  
Configuration was set  
to  
Single_Site_Backup  
or Multi_Site_Backup  
designated as the TS Access  
Management Link.  
NOTE:  
When DLCIs, PVC connections, and management PVCs for the first ISDN  
Link Profile have been configured manually, it is recommended that specific  
discovered DLCIs, PVC connections, and management PVCs be deleted  
manually via the Configuration menus. Otherwise, the manual configurations  
will be deleted along with the automatically configured ones.  
To specify when automatic backup is allowed or can occur, see Configuring the  
4-8  
December 2002  
9000-A2-GB31-00  
 
4. Feature-Specific Configuration  
Modifying ISDN Link Profiles  
Once an ISDN Link Profile is configured using the Automatic Backup Configuration  
feature, phone numbers and Calling IDs need to be entered. FrameSaver units  
with ISDN backup capability can originate or answer calls, as needed, so both  
phone numbers and Calling IDs are needed.  
Procedure  
1. Select Link Profiles, then Modify.  
Main MenuConfigurationISDNLink Profiles  
2. Add a name and phone number to the ISDN Link Profile(s) created by  
Automatic Backup Configuration.  
— Name for the destination entered (e.g., Tampa). The default setting is  
HQ_Site for the first ISDN Link Profile.  
— Phone numbers entered:  
For Originating a Backup Call  
For Answering a Backup Call  
Outbound and Alternate Outbound  
phone numbers  
Inbound Calling ID1 and ID2  
These are the phone numbers of units  
from which calls will be accepted.  
Valid characters can include:  
Numbers (0–9)  
Valid characters can include:  
Numbers (0–9)  
Special characters * and #  
Spaces  
Parentheses ( )  
NOTES:  
Remember to include local dial-out numbers (i.e., 9, then the number).  
For every originating (outbound) phone number entered, an answering  
(inbound) phone number must be entered at the far end, and vice versa.  
— Maximum Link Rate (Kbps) set to the appropriate speed, if necessary.  
— Caller Identification Method set to Proprietary if call validation is not  
required. The setting must be the same at both ends of the circuit.  
— An Alternate Outbound Phone Number should a call using the primary  
Outbound Phone Number be unsuccessful, if desired.  
3. Save the configuration.  
for configuration information.  
9000-A2-GB31-00  
December 2002  
4-9  
 
 
4. Feature-Specific Configuration  
Restricting Automatic Backup and Configuring Backup Timers  
You can specify when auto backup is allowed to occur. If backup is restricted and a  
backup is active when the allowed time for backups is over, then the backup is  
terminated and the data is returned to the primary data path regardless of the  
primary path’s condition.  
You can restrict auto backup to occur only:  
n
n
On certain days of the week  
At certain times of the day  
The following additional features can be configured:  
n
Delays can be configured to control how long the unit will wait before initiating  
backup when a DLCI is declared down, and how long it will wait to restore  
service once the DLCI is declared operational again.  
n
A threshold can be set to determine how many times a primary destination  
DLCI can transition between Active and Inactive before the unit initiates  
backup.  
Procedure  
To set the criteria and backup timers for automatic backup:  
1. Enable Auto Backup.  
Main MenuConfigurationAuto-Backup Criteria  
When a failure occurs, the unit automatically enables the Alternate Link and  
traffic is rerouted over the backup (alternate) interface.  
2. Specify the amount of delay after a DLCI is declared down before backup is  
initiated (DLCI Down Backup Activation Delay).  
3. Set the threshold for transitions of the DLCI’s status before backup is initiated  
(DLCI Down Backup Activation Transmission Threshold).  
4. Specify the amount of delay after a DLCI is declared operation before backup  
is ended (Backup Restoration Delay).  
5. Specify When Auto Backup Allowed – Always or Restrict. If Restrict is  
selected, specify the days and hours of the week during which automatic  
backup can take place.  
6. Save the configuration.  
Options, for configuration information.  
4-10  
December 2002  
9000-A2-GB31-00  
 
       
4. Feature-Specific Configuration  
Configuring the DBM Interface to Send SNMP Traps  
The ISDN DBM interface can be specified as an interface that monitors and  
generates SNMP traps:  
Main MenuConfigurationManagement and Communications→  
SNMP Traps  
The configuration options for doing this include:  
n
n
n
Link Trap Interfaces  
DLCI Traps on Interfaces  
ISDN Dial Control Traps  
When DBM is selected, trap messages are generated for linkUp and linkDown  
events on DLCIs and frame relay links for the originating DBM interface only. For  
peer-to-peer backup, backing up to a neighboring node like a regional node, dial  
control traps can be sent to trap manager(s).  
Configuration Options, for configuration information.  
Assigning DLCIs to a Backup Group  
DLCIs can be assigned to a Backup Group to reduce backup charges when  
redundant PVCs have been configured. This feature prevents backup as long as  
any DLCI in the group is operational.  
n
n
Backup is not initiated as long as one DLCI in the group is operational.  
Backup is terminated as soon as one DLCI in the group becomes operational.  
configuration information.  
9000-A2-GB31-00  
December 2002  
4-11  
 
               
4. Feature-Specific Configuration  
PVC Backup Over the Network Interface  
Generally, backup can be performed on the network interface’s frame relay link  
using a backup PVC, as well on an ISDN link; the unit does not have to have the  
ISDN DBM feature.  
In this case, create a DLCI Record on the network interface that will be used for  
backup, then modify the PVC Connections or Management PVCs to add the  
alternate destination.  
Setting Up Back-to-Back Operation  
Using this special feature, you can set up two FrameSaver units that are  
connected back-to-back without frame relay switches between them, as in a test  
bench setup using a crossover cable.  
Changing Operating Mode  
When setting up back-to-back operation:  
n
One unit must be configured for Standard operation, which is the setting for  
normal operation.  
n
The other unit must be configured for Back-to-Back operation so it presents  
the network side of the UNI (user-network interface).  
Only one of the units will have its operating mode changed.  
Procedure  
To set up back-to-back operation:  
1. On the unit to be configured for Back-to-Back operation, manually configure  
DLCIs; DLCIs should be configured before connecting the two units.  
2. Access the Change Operating Mode screen.  
Main MenuControlChange Operating Mode  
3. Select Back-to-Back Operation, and respond Yes to the Are you sure?  
prompt.  
4. Save the change.  
Procedure  
To return the unit to normal operation:  
1. Return to the Change Operating Mode screen and switch back to Standard  
Operation.  
2. Respond Yes to the prompt and save the change. The units can be  
reconnected to a standard frame relay network.  
4-12  
December 2002  
9000-A2-GB31-00  
 
                   
4. Feature-Specific Configuration  
9000-A2-GB31-00  
December 2002  
4-13  
 
4. Feature-Specific Configuration  
4-14  
December 2002  
9000-A2-GB31-00  
 
Index  
Auto Backup  
Auto-Configuration  
Numerics  
1MPort mode  
1Port mode  
1PPort mode  
2MPorts mode  
B
A
Access  
Back-to-Back  
Level  
operation  
Backup  
Alternate  
Alternate Destination  
Annex A and D  
Burst Size  
C
Call  
ARP  
assign  
Caller  
ATM  
Cell  
9000-A2-GB31-00  
December 2002  
IN-1  
 
   
Index  
changing  
configuring  
Character  
Circuit  
Class of Service  
Control Leads  
Clearing  
Event  
Clock  
COS  
creating  
Committed  
D
Data  
Communication Port  
Configuration  
Data Port  
DDS  
DE  
IN-2  
December 2002  
9000-A2-GB31-00  
 
Index  
DSLAM type  
Dial-Out  
DSX-1  
Directory  
disabling  
DTE  
Disconnect  
Discovery  
Frame Relay Mode  
displaying  
E
Easy Install  
EIA-530-A  
EIR  
Enterprise  
DSL  
Error  
Event  
IDSL  
SDSL  
Error Event  
Ethernet  
SHDSL  
Excessive  
9000-A2-GB31-00  
December 2002  
IN-3  
 
Index  
External  
Interface Status  
Internal  
IP  
F
Frame Relay  
Validation  
IP Enabled  
IP SLV  
ISDN  
G
Gateway Address  
General  
SNMP management  
K
H
HSSI  
L
latency  
hyperlink to more information  
Leased Line  
Line  
I
IDSL  
Line Rate  
IN-4  
December 2002  
9000-A2-GB31-00  
 
Index  
Link  
Mode  
modem  
port  
Monitor  
linkUp and linkDown  
LMI  
Multiplexed  
N
N1  
N2  
N3  
local  
Login  
Loopback  
Net Link  
M
Network  
Management  
DLCI records  
and Communication  
General SNMP  
interface  
menu  
Management  
9000-A2-GB31-00  
December 2002  
IN-5  
 
Index  
NMS  
Port  
assignment  
SNMP security  
Node  
communication  
modem  
Number of  
Status  
Port Type  
PPP  
O
operating mode  
Outbound  
P
Primary Clock  
Primary Destination  
payload management  
physical  
profiles  
Policing  
Proprietary  
IN-6  
December 2002  
9000-A2-GB31-00  
 
Index  
Protocol  
SNMP NMS  
Send  
Serial Line  
service level  
verification  
PVC  
Session  
setting up  
Q
SHDSL  
SLV  
R
Rate  
Round Trip Latency  
Timeout  
RMON  
router  
SNMP  
NMS security  
S
Sampling  
SDSL  
SNR Margin  
Source  
Secondary Clock  
9000-A2-GB31-00  
December 2002  
IN-7  
 
Index  
timing  
Status  
Enquiry  
Transmit Clock  
subrate  
suggestions  
System  
Traps  
Frame Relay and LMI  
Managers  
T
T1  
SNMP and dial-out  
troubleshooting  
Type  
T2  
T3  
Telnet  
Session  
Terminal  
Tests  
U
user interface  
communication port  
Threshold  
time  
V
V.35  
time slot assignments  
Timeout  
timers  
IN-8  
December 2002  
9000-A2-GB31-00  
 
Index  
W
warmStart  
events  
website  
X
X.21  
9000-A2-GB31-00  
December 2002  
IN-9  
 
Index  
IN-10  
December 2002  
9000-A2-GB31-00  
 

MPI Technologies Network Card Eth 10 User Manual
NEC Computer Monitor IDC3000 User Manual
NEC Switch N8406 019 User Manual
NordicTrack Treadmill NTL10941 User Manual
Olympus Microscope Magnifier SZ51 User Manual
Optoma Technology Projector Digital Tuner Output Projector User Manual
Panasonic Air Conditioner HQ 2201SH User Manual
Panasonic CRT Television CT 31XF43 User Manual
Panasonic Electric Shaver ES4815 User Manual
Panasonic Telephone KX T3806BA User Manual