Installation Instructions
UIM-1000T
Gigabit Ethernet Uplink Interface Module
Net to Net Technologies strongly recommends the use of proper electrostatic discharge (ESD) precautions when
handling this equipment.
CAUTION
1.0 INSTALLATION
1.1 Unpack and Inspect the Equipment
The following components should be included:
z 1 UIM-1000T
z 4 #6 Phillips Panhead Nylon Locking Screws
z 2 #6 Phillips Beige Flathead Screws
If there is visible damage, do not attempt to install the UIM-1000T; contact Customer Support at 1-
877-638-2638 (001-603-427-0600 for international customers) or [email protected].
1.2 Install the UIM-1000T on a Multiplexer Uplink Module (MUM2000-2)
An uplink interface module (UIM) provides the upstream network connection, via a MUM, for Net to
Net Technologies' IP DSLAMs; neither an IP DSLAM nor a MUM can function without a UIM.
The MUM2000-2 is currently Net to Net's only multiplexer uplink module capable of supporting the UIM-1000T.
NOTE
z
Select a port on the MUM2000-2 for installation of the UIM-1000T: either port (1 or 2) may be
used. Although not required for operational purposes, if redundancy is desired two UIMs may
be installed on a MUM2000-2, one in each port.
z
Remove the blanking plate from the selected port.
Blanking plates should be stored for possible future use: if a UIM-1000T is removed from the
MUM2000-2, it must be replaced with either another UIM or a blanking plate. DO NOT
OPERATE THE MUM2000-2 WITH AN OPEN UIM PORT.
CAUTION
z
Carefully slide the faceplate of the UIM-1000T under the lip of the MUM2000-2 faceplate at
the selected port opening such that the UIM-1000T circuit board is facedown and the label
shows through the MUM2000-2 port opening with the UIM-1000T model name along the right-
hand edge.
220-0000078 rev 01
1000Base-T RJ45 Port Pinout
PIN CONNECTION
1
2
3
4
5
6
7
8
TP0+
TP0-
TP1+
TP2+
TP2-
TP1-
TP3+
TP3-
3.0 ADDITIONAL INFORMATION
3.1 LED Indications
LED
State
Indication
Additional Information
Dplx
solid green Full Duplex Ethernet The UIM-1000T Ethernet connection only operates
(Duplex)
connection is
established
under full duplex data transmission. As such, whenever
an Ethernet connection is present, the Dplx LED will be
illuminated.
no
no Ethernet
If the Dplx LED is not illuminated then an Ethernet
connection has not been established and the Lnk LED
will remain unlit as well.
illumination connection
Act
flashing
Ethernet activity
Traffic is flowing at 1 Gbps.
Heavy traffic flow.
(Activity) amber
solid amber heavy Ethernet
activity
no
no Ethernet activity
No current traffic flow.
illumination
Lnk (Link) solid green 1 Gbps Ethernet
The UIM-1000T Ethernet connection only operates
uplink connection is under full duplex data transmission. As such, if the Lnk
established
LED is illuminated, the Dplx LED will also be
illuminated.
no
no Ethernet
If the Lnk LED is not illuminated then an Ethernet
connection has not been established and the Dplx LED
will remain unlit as well.
illumination connection
3.2 Regulatory Compliance for Class A Equipment
The following regulatory compliance information applies to the UIM-1000T as mounted on a
MUM2000-2 and installed in one of Net to Net Technologies' IP DSLAMs.
3.2.1 US Federal Communications Commission (FCC)
Note: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
220-0000078 rev 01
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Caution: Changes or modifications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.
3.2.2 Industry Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada.
3.2.3 Europe
This Class A product complies with European Norm EN55022.
Warning: In a domestic environment this product may cause radio interference in which case
the user may be required to take adequate measures to correct the situation.
220-0000078 rev01
© Copyright 2002 Net to Net Technologies, Inc.
™ The Net to Net Logo is a trademark of Net to Net Technologies, Inc.
Worldwide Headquarters
Net to Net Technologies
112 Corporate Drive
Portsmouth, NH 03801
USA
EMEA Headquarters
Net to Net Technologies
Victoria House 19 Park Way
Newbury Berkshire RG14 1EE
UK
+1 877-638-2638
+44 (0) 1635 570950
220-0000078 rev 01
|