Oreck Vacuum Cleaner U2510RH User Manual

®
S I M P L Y  
A M A Z I N G  
USERS GUIDE  
U2510RH  
U2520RH  
U2530RH  
HIGH SPEED UPRIGHT VACUUM  
CLEANER WITH  
®
CLEANING SYSTEM  
•IMPORTANT•  
SAVE THIS BOOKLET!  
Includes:  
• Safety Warnings  
• Warranty  
• Operating Instructions  
• Trouble Diagnosis  
• Accessories  
 
Warranty  
Troubleshooting Guide  
ORECK MANUFACTURING COMPANY: (Oreck Manufacturing Company  
gives you the following limited warranty for this product only if it was origi-  
nally purchased for residential use, not resale, from Oreck or an Oreck  
Authorized Retail Dealer.)  
WARNING: Unplug cord from electrical  
outlet before servicing.  
SAVE SERVICE CALLS...CHECK THESE FIRST:  
Oreck will repair or replace, free of charge, to the original purchaser, any  
part which is found to be defective in material or workmanship within three  
(3) years of the date of purchase; ten (10) years on housing. This limited  
warranty applies to normal domestic use. Any commercial use of this  
product will void this limited warranty. This limited warranty covers the  
revolving roller brush for one (1) year for residential use only.  
• Is the disposable filter dust bag full?  
• Are pores of filter dust bag clogged with powder or fine dust?  
• Is anything clogging the revolving brush, lower tube, intake opening,  
fan housing or connector assembly opening?  
• Is the belt in place and turning the brush?  
• Are the brush ends in the proper location?  
This limited warranty does not cover the replacement of expendable or  
consumable parts such as carbon motor brushes, edge brushes, drive  
belts, bulbs, disposable bags and other parts subject to normal wear  
unless they are defective in material or workmanship.  
• Does the brush turn freely? Are hair, string or rug fibers wound around  
the brush?  
PROBLEM  
POSSIBLE SOURCE  
AREAS TO CHECK  
This limited warranty does not apply to any part subjected to accident,  
abuse, commercial use, alteration, misuse, damage caused by act of God,  
the use of voltages other than indicated on the serial number displayed on  
this product or service of this product by other than Oreck or a participating  
Factory Authorized Service Center.  
Not plugged in  
properly.  
Be sure cleaner is  
firmly plugged into  
wall outlet.  
CLEANER  
WILL NOT RUN  
Oreck does not authorize any person or representative to assume or grant  
any other warranty obligation with the sale of this product.  
No electricity in wall  
outlet.  
Check electrical  
source–fuse or  
circuit breaker.  
Oreck’s limited warranty is valid only if you retain proof of purchase from  
Oreck or an Oreck Authorized Retail Dealer for this product. If you  
purchase this product from any other source, your purchase is “AS IS,”  
which means Oreck grants you no warranty, and that you, not Oreck,  
assume the entire risk of the quality and performance of this product,  
including the entire cost of any necessary servicing or repairs of any  
defects.  
CLEANER  
DOES NOT PICK UP  
Filter bag is full.  
Replace filter bag.  
See “To Replace  
Paper Filter Dust Bag.”  
Nozzle or intake  
pivot clogged.  
Clear obstruction.  
Oreck’s liability for damages to you for any costs whatsoever arising out  
of this statement of limited warranty shall be limited to the amount paid for  
this product at the time of original purchase, and Oreck shall not be liable  
for any direct, indirect, consequential or incidental damages arising out of  
the use or inability to use this product.  
Belt is broken or  
stretched.  
Replace belt.  
Brush is worn.  
See “To Replace or  
Adjust Brush.”  
Some states do not allow the exclusion or limitation of incidental or conse-  
quential damages, so the above limitation or exclusion may not apply to  
you.  
Bag tube clogged.  
Clear obstruction.  
Change bag.  
Bag pores are  
clogged with fine  
dust.  
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT,  
INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION  
TO THE WARRANTY PERIOD, AND NO WARRANTIES, WHETHER  
EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD.  
Impeller fan is  
broken.  
Return to Service  
Center for repair.  
Some states do not allow limitations on the duration of implied warranties,  
so the above limitation may not apply to you.  
Revolving brush is  
not even at both  
ends.  
Check brush roll end  
cards. Make sure  
words “OLD” or  
“NEW” match at  
each end.  
This warranty gives you specific legal rights, and you may also have other  
rights which vary from state to state.  
ALL OTHER SERVICING SHOULD BE DONE BY AN  
ORECK AUTHORIZED SERVICE CENTER.  
CALL CUSTOMER SERVICE HOT LINE  
US: 1-800-989-3535 Canada: 1-888-676-7325  
Whenever calling, please be sure to have your model and serial  
number from data plate.  
3
 
1
2
3
4
5
Upper Handle  
Connector Assembly  
6
7
8
9
10  
15  
20  
25  
NJUSQU’À  
ENTENDRE UN BRUIT  
HASTA  
ESCUCHAR UN  
DE SUJECIÓN  
11  
16  
21  
26  
12  
17  
22  
27  
13  
18  
23  
14  
19  
OLD  
NEW  
24  
Tube  
Fan Housing  
Retainer  
Spring  
O-ring  
Intake Opening  
Intake Opening  
28  
Fan Housing  
Connector  
Deflector  
Opening  
4
 
4. Although your upright will pick up pins, paper clips, and other  
small objects, it is recommended that these be removed from the  
floor before you vacuum. Failure to do so may result in permanent  
damage to the motor suction fan and its housing.  
Parts List  
To assist you in identifying components of your vacuum, the parts have  
been numbered as follows:  
5. WARNING: Do not use your vacuum cleaner on damp or wet  
surfaces. This will cause damage to the vacuum cleaner and is  
dangerous to the user. Damage caused by use on wet or damp  
surfaces is not covered under warranty.  
10  
1
2
3
4
5
6
7
8
9
Handle section, upper  
Tube, lower  
Power head  
Outer bag  
Paper filter dust bag  
Power cord  
Retaining spring  
Bag tension bar  
Zip fastener  
11  
9
1
6. REPLACE THE BELT EVERY 6 MONTHS.  
7. Change the disposable filter dust bag at least once a month—  
even if it is not full! The collected dust in the dust bag can cause  
odor, attract moisture, and can affect the efficiency of the cleaner.  
8. DO NOT run the vacuum cleaner over the cord. The revolving  
brush could damage the cord.  
12  
5
4
8
10 On/off switch  
11 Cord hook  
12 Connector assembly  
13 Fan housing  
9. Use caution when vacuuming over area rug edges and fringe.  
2
6
General Information  
14 Cord assembly  
The performance of your new cleaner greatly depends upon care and  
maintenance. The instructions in this manual will guide you in  
performing basic care and maintenance. To obtain the most satisfying  
years of service read the instructions and keep them handy for future  
reference.  
13  
7
14  
3
Disposable Paper Filter Dust Bags  
Assembly  
Disposable paper filter dust bags play a very important role in the  
efficiency of your ORECK vacuum cleaner. The purpose of the paper  
bag is to trap dirt, but at the same time it must be porous enough to  
allow air to pass through. If the paper bag becomes clogged, no air can  
pass through the cleaner and cleaning cannot take place, regardless of  
the cleaner’s power.  
fig. 1 Before assembling appliance, remove screws from the connector  
assembly. Remove cardboard insert by pulling upward.  
fig. 2 With ON/OFF switch facing the front of the unit, slide upper  
handle section over matching section of the connector assembly.  
Insert short screw into top hole and long screw into the bottom  
hole then tighten firmly until handle is no longer loose.  
To keep your cleaner operating at maximum efficiency, change the dust  
bag frequently. DO NOT FILL ABOVE THE LINE INDICATED ON THE  
DUST BAG.  
fig. 3 Attach cord to cord clip by pressing cord above and below clip  
Be sure the disposable paper filter dust bag is installed properly.  
ensuring the cord is fully rested in clip.  
All paper dust bags are not the same. Your ORECK disposable  
dust bags have been designed to be used with the ORECK cleaner.  
Using bags other than genuine ORECK TYPE CC disposable bags  
will affect the cleaning ability of your cleaner and could cause  
damage to it.  
Operating Instructions  
Make sure disposable paper filter dust bag is in place. DO NOT operate  
the cleaner without a paper filter dust bag. Plug the power cord into an  
electrical outlet and press the ON(l) - OFF(O) switch on handle  
assembly when ready to operate.  
The Belt  
The belt on your vacuum cleaner controls the speed of the revolving  
brush and is very important for the effective operation of the cleaner. If  
the belt becomes stretched or cut, it will cause the revolving brush to  
stop completely or slow down. See instructions in the manual for  
replacing belt.  
Up-Position Lock  
fig. 4 Place foot on power head and lean handle back gently to release  
lock for vacuum use. Return handle to the full upright position to  
engage lock.  
An extra belt is stored in the baseplate of your cleaner. When  
buying replacement belts, use ONLY ORECK genuine belts. Belts  
other than ORECK belts will not operate the revolving brush  
correctly and may create undue stress which will cause damage to  
the motor and brush bearings. Using belts other than ORECK belts  
will void the warranty.  
NOTE: Do not operate the unit while in the upright and locked position.  
Do not let the unit run while in any one stationary position for any period  
of time. Keep the unit moving while in operation.  
For Easy Power Cord Storage  
fig. 5 Wrap power cord around cord hook on handle and cord hook on  
Lubrication  
connector. Secure cord to "U" shaped part on plug.  
The vacuum cleaner motor bearings are factory lubricated and sealed.  
Further lubrication is not required.  
Operating Recommendations  
This new ORECK XL High-Speed Upright is one of the finest, fastest,  
and strongest units in its class. You’ll love the way it cleans, gets under  
things, and it’s SO lightweight and easy to use.  
General Cleaner Care  
At least once a month, check for and  
remove excessive lint, string or hair from  
revolving brush.  
The following are a few simple suggestions regarding its operation:  
1. When inserting a new disposable paper filter dust bag—FIRST  
PUFF OUT and OPEN THE BAG.  
Wipe the outside of the cleaner with a  
damp cloth. Also clean the connector  
deflector assembly area, base of cleaner  
and fan housing area. If there is dust in  
the outer bag, vacuum it or shake it out.  
2. When the disposable filter dust bag is full, REPLACE IT.  
3. If at any time the machine does not pick up properly or makes an  
unusual noise, STOP OPERATION and service.  
A little preventative maintenance will keep  
your cleaner looking new and will ensure  
continued cleaning effectiveness.  
5
 
CAUTION—Wood Floors, Soft (Vinyl, Asphalt Tile, etc.) Floor  
Surfaces and Polished Floor Finishes  
IMPORTANT: Unless the brush is worn as indicated above, both  
bearings must be in the “NEW” position. When rotating, both  
bearings must be in the “OLD” position. Unmatched settings will  
cause damage to your machine.  
Using An Oreck Fresh Air® Tab  
Use floor and floor finish manufacturer’s recommended methods of  
cleaning. The metal strip on the base of the cleaner could be damaged  
if used on concrete or abrasive surfaces, and, therefore, cause damage  
to wood floors, soft (vinyl, asphalt tile, etc.) floor surfaces and polished  
floor finishes. The roller brush may also scuff very soft finishes. Do not  
operate the unit while in the upright and locked position. Do not let the  
unit run while in any one stationary position for any period of time. Keep  
the unit moving while in operation.  
fig. 20 Your ORECK XL vacuum cleaner has a special ORECK FRESH  
AIR® tab pocket. This pocket is located inside the outer bag in  
the area where the paper disposable bag attaches to the intake  
tube. Insert tablet in pocket if desired.  
To Replace Filter Dust Bag  
Stuffing or Blockage  
WARNING: Unplug cord from electrical  
outlet before servicing.  
IMPORTANT: On plush and new carpets, stuffing may occur inside the  
the intake tube and the lower tube assembly. This is due to excessive fuzz  
and loose cuttings in the carpet. Stuffing could occur for the first few  
cleanings until all the loose material is removed. Due to the high efficiency  
of the cleaner, many older carpets will cause stuffing when the cleaner is  
first used on them. If your vacuum cleaner does not pick up properly, or  
makes unusual noise and the outer bag does not fluff up or balloon open,  
follow these steps:  
BAG REMOVAL:  
fig. 6 Unzip outer bag completely.  
fig. 7 Pull bag cardboard collar to release bag dock door from  
connector. Bag dock door will hinge downward.  
fig. 8 Gently pull bag cardboard collar upward out of the bag dock.  
The dust seal will close automatically.  
WARNING: Unplug cord from electrical  
outlet before servicing.  
BAG INSTALLATION:  
fig. 9 Slide the cardboard collar completely onto bag dock door.  
fig. 21 Check for blockage at the mouth of the intake opening. If there  
is blockage, remove it with long-nose pliers, a screwdriver or  
coat hanger. If you can not reach the blockage, remove  
baseplate (fig. 22).  
fig. 10 Firmly push bag dock door with both thumbs on indication point  
until it snaps.  
fig. 23 If the blockage is not at the base, remove lower tube. Unhook  
How to Replace a Worn Belt  
retainer spring, releasing bottom of bag.  
WARNING: Unplug cord from electrical  
outlet before servicing.  
fig. 24 Twist lower collar counterclockwise to slide up. Pull tube out of  
base.  
fig. 25 Check for blockage. If blockage is in the tube, remove with a  
fig. 11 Remove the replacement belt from the storage channel.  
coat hanger.  
fig. 12 Remove the door by removing the hold down screw located on  
fig. 26 If tube is not blocked, look into fan housing. Remove debris  
side of power head.  
with long-nose pliers, a screwdriver or coat hanger.  
fig. 13 Slide the door forward by prying open with a screwdriver or coin.  
fig. 24 To reassemble, check O-ring on tube, and replace if damaged.  
Vacuum will not operate properly without the tube O-ring. Slide  
O-ring to approximately 2" from base of tube. Replace tube by  
first lining up slot at base of tube with inner tab inside fan  
housing. Then reinsert tube and push down until the tube is  
seated. Make sure O-ring is in place against fan housing  
opening. Replace and tighten collar until collar locking tabs are  
locked in place.  
fig. 14 Remove the belt from the brush roll pulley and motor drive shaft.  
fig. 15 Loop the new belt over the motor drive shaft. Place the opposite  
end of the belt on the brush roll pulley. Rotate the brush roll  
three (3) complete revolutions to ensure that no part of the belt  
is overhanging the end of the motor drive shaft.  
fig. 13 Replace the door by sliding it into the groove at the bottom of  
the housing.  
fig. 27 Make sure collar is not cross threaded on housing. Reattach  
fig. 12 Replace the hold down screw and tighten.  
bag spring (fig. 23).  
To Adjust or Replace Brush  
fig. 28 Many times blockage occurs due to a full dust bag causing dirt to  
back down the air flow system. When that happens, the  
WARNING: Unplug cord from electrical  
outlet before servicing.  
fig. 16 To determine if the brush is worn, place a firm straight edge  
across the nozzle opening. If brush bristles do not extend  
beyond baseplate, brush should be adjusted.  
blockage will be at the top of the system, starting in the area  
where the dust bag connects to the connector assembly.  
NOTE: If the above actions do not correct the problem, contact an  
Oreck authorized service center or call the customer service center.  
US: 1-800-989-3535 Canada: 1-888-676-7325  
fig. 17 Remove the baseplate by removing 5 screws.  
fig. 18 Remove the belt and brush roll from the housing.  
fig. 19 Rotate both bearing assemblies at ends of brush roll to show  
"OLD" and replace in the holding channels in the housing.  
NOTE: The bearing assembly setting marked "OLD" has no ribs on the  
top of the assembly. The one marked "NEW" has several ribs. When  
rotating bearings, make sure both bearing assembly settings are the  
same and face up when replacing the brush roll.  
fig. 16 Reassemble the belt and the baseplate and check bristle height  
above baseplate at each end of brush.  
If a previous adjustment has already been made and bristle height does  
not extend above baseplate, a new brush assembly should be ordered.  
6
 
7
 
©2005 Oreck Holdings, LLC. All rights reserved. All word marks, logos, product configurations, and registered trademarks are owned and used under the authority of Oreck Holdings, LLC. Printed in America  
75726-01 REV A  
06/05 ECN# R-8042  
 

Miller Electric Welder INTEGRA 201 241 User Manual
Mr Coffee Coffeemaker ECTX81 User Manual
Multiquip Portable Generator DCA400 User Manual
Murphy Plumbing Product BLSK1 Series User Manual
NDC comm Network Card NDC 3 User Manual
NEC Telephone P N 1093099 User Manual
North Star Portable Generator 8000 PPG User Manual
Omnimount Projector Accessories 3N1 PJT User Manual
Oregon Scientific Marine Radio WMR86 User Manual
Panasonic Car Stereo System C9801W User Manual