NOTE: The iConverter CWDM/X modules can not be installed in slots 4, 8, 12 and
16 of a 19-Module Chassis or in the top slot of a 2-Module Chassis or in a 1-Module
Redundant Power Chassis.
NOTE: The iConverter 8-Channel Double-Wide CWDM/X can only be installed
in a 2-Module Chassis or 19-Module Chassis with the exception of slots 4/5, 8/9,
12/13 and 16/17.
iConverter CWDM/X 4 and 8 Channel MUX/DEMUX
USER MANUAL
Design Considerations
Product Overview
iConverter CWDM/X modules are passive devices that require no external power.
Attenuation (signal loss) of less than 2.7dB will be realized through each port on the
module (see the CWDM/X Data Sheet for exact loss specification for each model).
Detailed calculations should be performed for each fiber optic link in the network to
ensure the proper optical devices are specified with sufficient transmitter power.
Omnitron’s iConverter CWDM/X Coarse Wave
Division Multiplexing (CWDM) Multiplexer/
Demultiplexer(MUX/DEMUX)modulessupport
ITU-T G.694.2 wavelengths between 1270nm
to 1610nm in 20nm increments. Up to sixteen
separate wavelengths can be transported over
a dual fiber common link.
When calculating optical loss, ensure that the total loss, plus a safety factor (typically
3dB) does not exceed the optical power budget. The optical power budget is the
difference between the transmitter optical output power and the receiver’s optical
sensitivity. The transmitter optical output power and receiver optical sensitivity values
can be obtained from the manufacturers of the respective equipment. Please consult
the iConverter data sheets for CWDM/X signal loss specifications.
The iConverter CWDM/X modules are available in 4 and 8-Channel models,
supporting a variety of wavelengths and optional port configurations.
Port Definitions
For more information, access Omnitron’s documentation download web page to
view all relevant documents:
Warranty
WARNING
The operating description in this Instruction Manual is for use by qualified personnel only. To avoid electrical shock, do not perform any
servicing of this unit other than that contained in the operating instructions, unless you are qualified and certified to do so by Omnitron
Systems Technology.
Warranty
This product is warranted to the original purchaser against defects in material and workmanship for a period of ONE YEAR from the date
of shipment. You may register your product on the Internet at http://www.omnitron-systems.com. During the warranty period, Omnitron
will, at its option, repair or replace a product which is proven to be defective.
Figure 1: Port Locations for 4-Channel CWDM/X Module
For warranty service, the product must be sent to an Omnitron designated facility, at Buyer’s expense. Omnitron will pay the shipping
charge to return the product to Buyer’s designated US address using Omnitron’s standard shipping method.
Limitation of Warranty
The foregoing warranty shall not apply to defects resulting from improper or inadequate use and/or maintenance of the equipment by
Buyer, Buyer-supplied equipment, Buyer-supplied interfacing, unauthorized modifications or tampering with equipment (including removal
of equipment cover by personnel not specifically authorized and certified by Omnitron), or misuse, or operating outside the environmental
specification of the product (including but not limited to voltage, ambient temperature, radiation, unusual dust, etc.), or improper site
preparation or maintenance.
No other warranty is expressed or implied. Omnitron specifically disclaims the implied warranties of merchantability and fitness for any
particular purpose.
Exclusive Remedies
The remedies provided herein are the Buyer’s sole and exclusive remedies. Omnitron shall not be liable for any direct, indirect, special,
incidental, or consequential damages, whether based on contract, tort, or any legal theory.
Figure 2: Port Locations for 8-Channel Single-Wide CWDM/X Module
040-08860-001B 1/09
Omnitron Systems Technology * 140 Technology Dr. #500 * Irvine, CA 92618
Page 1
|