OPERATION MANUAL
NIGHT VISION SCOPE
MB-3
In USA : 3310 Prospect Ave. Cleveland, OH 44115
In Canada : 1183 Finch Ave. W., Suite 302, Toronto, ON. M3J 2G2 Canada
Tel: (416) 663-6963 Fax: (416) 663-9065
Newcon International ltd. © 1998-2003 Printed in Canada
Email: [email protected]
• NEVER connect the unit to external power sources
• ALWAYS remove batteries when not in use for a long period
• ALWAYS keep the objective lenses covered when not in use
• ALWAYS store in a warm dry place when not in use
9. ACCEPTANCE CERTIFICATE
NIGHT VISION DEVICE MB-3
Serial Number _______________________________
Model MB-3_____________________
corresponds to technical conditions ADSH 3.807.020 TU and is
admitted for use.
Date of production -___________________
Place for seal
Quality inspector ____________________
(Signature)
THE SOLE OBLIGATION OF NEWCON UNDER THIS LIMITED
WARRANTY SHALL BE TO REPAIR OR REPLACE THE COVERED
PRODUCT, IN ACCORDANCE WITH THE TERMS SET FORTH HEREIN.
NEWCON EXPRESSLY DISCLAIMS ANY LOST PROFITS, GENERAL,
AND SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES WHICH
MAY RESULT FROM BREACH OF ANY WARRANTY, OR ARISING OUT
OF THE USE OR INABILITY TO USE ANY NEWCON PRODUCT.
CONTENTS
1. Overview
i) Application and Features of MB-3
ii) Warning
iii) Precautions
2. Components
8. CUSTOMER SUPPORT
3. Specifications
4. Construction
Should you experience any difficulties with your Newcon OPTIK product,
consult the enclosed manual. If the problem remains unresolved, contact our
customer support department at
(416) 663-6963. Our operating hours are 9am-5pm, Monday - Friday, standard
East time.
At no time should equipment be sent back to Newcon without following
the instructions of our technical support department. Newcon accepts no
responsibility for unauthorized returns.
5. Operating Instructions
5.1 Pre-starting procedures
5.2 Testing of operation
5.3 Operation at night
6. Troubleshooting
7. Warranty
8. Customer support
9. Acceptance Certificate
To locate the NEWCON Authorized Dealer call:
Tel: (416) 663-6963 Fax: (416) 663-9065
E-mail: [email protected]
THANK YOU FOR PURCHASING MB-3 NIGHT VISION DEVICE.
PLEASE DEMAND TO CHECK THE DEVICE FOR PROPER
OPERATION WHEN BUYING IT. PLEASE READ ALL THE
INSTRUCTIONS CAREFULLY BEFORE USING.
The defective products should be shipped to:
In USA: 3310 Prospect Ave. Cleveland, OH 44115
In Canada or overseas: 1183 Finch Ave. W., Suite 302, Toronto, ON. M3J 2G2 CANADA
1. OVERVIEW
MB-2 Night Vision scope is a sophisticated optico-electronic observation
device designed to allow observations of personnel and orientation in nighttime
conditions. The unit is utilizing an image intensifier, which amplifies available
moonlight, starlight or man-made light. The viewer was designed to be easy to
use, convenient to carry and provide many years of operation.
Some of the typical activities where the MB-2 will be useful: boating, search
and rescue, law enforcement, wildlife observation, security.
7. WARRANTY
NEWCON OPTIK warrants this product against defects in material and
workmanship for one year from the date of the original date of consumer's
purchase, but no more than 18 months from the date of delivery being indicated
and stamped on the acceptance certificate purchase. Should your NEWCON
product prove defective during this period, please bring the product securely
packaged in its original container or an equivalent, along with proof of the date
of original purchase, to your NEWCON Dealer. NEWCON will, repair (or at
its option replace), the product or part thereof, which, on inspection by
NEWCON, is found to be defective in materials or workmanship.
Features
•
•
•
•
Totally waterproof construction.
Will float on the water if accidentally dropped.
Nitrogen purged optics, to prevent fogging
One stage image intensifier tube with Multi alkaline photocathode and
image tube gain of no less than 500 times ensures observation at 1/4 moon
and better conditions;
•
•
High quality wide-angle lens.
The built in infra red illuminator allows observations in total darkness (i.e.
basement or cave);
What This Warranty Does Not Cover:
NEWCON in not responsible for warranty service should the product fail to be
properly maintained or fail to function properly as a result of misuse, abuse,
improper installation, neglect, damage caused by disasters such as fire, flood,
and lightning, improper electrical current, or service other than by a NEWCON
Authorized Service. Postage, insurance, or shipping costs incurred in
presenting your NEWCON product for warranty service are your responsibility.
Please include a cheques or money order made out to NEWCON OPTIK for the
amount of US$10.00 to cover shipping and handling.
•
The internal lens with focusing mechanism ensures adjustment for sharpness
for both near and remote objects;(optional)
•
•
The eye piece allows Dyoptric adjustment for the eyes of the viewer;
Soft rubber eye-cap protects from the disturbing lateral light and occasional
impacts, thus making surveillance more comfortable;
Standard and commonly available AAA-batteries ensure operation of the
device of no less than 10 hours;
Two switch buttons ensure separate switching of the night vision device and
the IR LED illuminator, thus providing economic use of batteries' power;
Original compact design and ergonomic shape make the device handy and
comfortable to hold with one hand
•
•
•
NEWCON OPTIK may replace any product that has been discontinued or is
out of stock, by another current product of comparable value and function.
NEWCON OPTIK DISCLAIMS ANY WARRANTIES, EXPRESS OR
IMPLIED, WHETHER OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR USE, EXCEPT AS EXPRESSLY SET FORTH
HEREIN.
If the view still does not seem in focus, clean the lenses; they could be foggy or
dusty.
Warning!
After transportation or keeping the device at temperature lower than
-25°C (-13°F), the device must be warmed up to ambient temperature,
from -20°C (-4°F) to +40°C (104°F) during 2-3 hours.
Unit flashes
It is normal for the unit to flash within the first 2 minutes of activation. If the
flashing continues afterwards the following is a possible cause: bright
environment (even with the cap closed!)
Precaution
MB-3 is a precision optical instrument equipped with electronics.
Therefore, it should be handled with due care.
•
•
•
Keep your device away from direct sunlight, impacts, dust, moisture, and
sudden changes of temperatures.
Do not touch the optical surfaces with fingers. Doing so may damage the
anti-reflection coating.
Cleaning of optical surfaces is possible only with professional camera lens
cleaning supplies.
Condensation accumulates on the parts.
It is O.K. to use the scope in cold. However, when the unit is brought from the
cold into a warm environment, it has to warm up for up to 5 hours (not
minutes!). Only then it is allowed to turn it ON again.
•
•
•
•
To clean the exterior of the device, use only a soft clean cloth.
Do not take the cover off the lens if not necessary.
Keep away from heating appliances and central heating.
Make sure to switch off the unit during periods of non-operation and
when storing the device for long period of time.
Do not apply superfluous efforts at work with lens assembly, agile elements
and thread connections.
Due to considerable optical magnification of the eye-piece some small
structures inside the tube coating in the form of dark and/or white points
may be seen in the field of view which does not affect the serviceability of
the device;
Visibility decreases and / or disappears.
Bright light sources (moon, projectors or headlights) may cause visibility to
degrade or even completely disappear. Move the scope away from the light
source immediately. The image should be restored in within 2 minutes.
•
•
Poor atmospheric conditions such as fog, haze or extremely dark environments,
will decrease the visibility distance of the unit.
•
The resolving power (resolution) may change in the direction from the
center towards the perimeter of the field of view. This is an inherent feature
of the image tube type utilized in the device. We would recommend to
place the scene of observation in the center of the field of view.
2. COMPONENTS
5.3. Operation at night
MB-3 is supplied with the following components:
AT MOON LIGHT
NAME
QUANTITY
MB-3 N.V
Carrying strap
Case
AAA batteries (optional)
Manual
Warranty Registration Card
1
1
1
2
1
1
Take off the lens cover (8). Turn on the device using switch (4). Turning the
eye-piece focusing lever (3) adjust to achieve the most clear image on the
screen. Then obtain the most clear-cut image of the object focusing with ring(2)
Repeat the steps of focusing if necessary.
AT INSUFFICIENT AMBIENT ILLUMINATION
Activate switch (4) for switching on the device. Press button (5) for switching
on IR illuminator. Direct the device on the object to be viewed.
3. SPECIFICATIONS of MB-3
Magnification, X
2.5 ±0.2
If brightness of the screen is decreasing, replace the batteries.
Take out the batteries during long time periods of non-operation of the device.
Field of View, angl.., degrees, not less......…………..….. 26
Minimum Focus Range, m......…………………………….0.8
Operating illumination..………………….from moon light to star’s light
Resolving Power, angl., seconds, not more..
6. TROUBLESHOOTING
at full moon................…………………....................... 200
The scope does not work.
at stars light and 1/4 of full moon..............
Dyoptric Compensation, Dptr., no less........
Integral illuminator Working Wave Length, mm
350
±4
780-880
Check that the batteries are installed properly.
Check the charge of the batteries.
Replace if they are weak.
Power Supply..................................……………………. 3V (2 AAA)
Dimensions, mm, not more.....................………………. 106X151X74
Weight. kg, not more.............................……………….. 0,5
Do not use old batteries with new ones.
The image does not appear in focus.
NOTE : As the design is being continuously improved some
descriptions may differ from those given above.
Bring the inspected object to the center of the image. Turning the eye-piece
focusing lever (3) adjust to achieve the clearest image on the screen. Then
obtain the most clear-cut image of the object
4. CONSTRUCTION
5. OPERATION INSTRUCTIONS
WARNING!
3
4, 5
7
NEVER OPERATE YOUR NIGHT VISION DEVICE IN DAYLIGHT
AREAS WITHOUT THE LENS COVER ON! NEVER DIRECT THE
LENS IN THE DIRECTION OF BRIGHT LIGHT!
1
2
5.1 Pre-starting procedures.
1. Unpack the device. In order to replace the batteries unscrew battery house
cover (7) and replace the batteries observing the polarity indicated; close cover
(7). First, make sure the lens caps (8) are closed: Check the functioning of the
device by switching it on (click switch 4) and looking through eye-piece (3). If
power supply and the batteries are O.K., you will see greenish lit screen. If the
screen is not lit, check the batteries. Replace the batteries if necessary. If
everything works, now is a great time to fill the warranty card. You can find the
unit’s serial number on eyepiece focusing ring (3) or lens focusing ring (2).
8
NOTE: The scope will remain on for up to several minutes after releasing the
ON button. This is normal.
6
NOTE: Since the unit is tightly sealed to remain waterproof, lever (3) will not
rotate easily.
9
5.2. Testing of operation
1- Body
2-
3-
4-
5-
6-
7-
8-
Lens Focusing Ring
Eye-piece Focusing Lever
Switch Button for the Scope
IR Illuminator Switch
IR Illuminator
Turn on the device-using switch (4). Lens cap (8) must be on. Direct the device
on an object placed within 40-50 m from the viewer. Turning the eye-piece (3)
try to achieve the sharpest image on the screen of the image tube. For close
focusing rotate the front lens (2)
Battery House Cover
Lens Cover
9- Carrying Strap
|