National Instruments Welding System NI PXIe 1062Q User Manual

USER GUIDE  
NI PXIe-1062Q Power Supply  
Shuttle  
The NI PXIe-1062Q power supply shuttle is a replacement part for the  
NI PXIe-1062Q chassis.  
Caution This power supply is not compatible with any other National Instruments chassis.  
Introduction  
To minimize downtime caused by a power-supply failure, the  
NI PXIe-1062Q chassis has a modular power supply shuttle. This power  
supply shuttle includes the chassis power supply, cooling fans, and  
fan-control circuitry. Key features of the power supply shuttle include:  
Universal AC input with automatic voltage and frequency ranging  
Over-current protection via push-reset circuit breaker  
Remote power monitoring and inhibit via a rear-panel connector  
Temperature-sensing module that can adjust fan speed based on  
air-intake temperature to minimize audible noise  
Circuitry to control a front-panel LED that indicates power supply  
failure  
Unpacking  
Carefully inspect the shipping container and the power supply shuttle for  
damage. Check for visible damage to the metal work. Check to make sure  
all handles, hardware, and switches are undamaged. Visually inspect the  
inside of the shuttle for any possible damage, debris, or detached  
components. If damage appears to have been caused during shipment, file  
a claim with the carrier. Retain the packing material for possible inspection  
and/or reshipment.  
 
4
2
3
9
10 11  
7
12  
14  
13  
5
6
8
1
1
2
3
4
5
6
7
Power Supply Shuttle  
Push-Reset Circuit Breaker  
Universal AC Input  
Chassis Ground Screw  
10 MHz REF OUT BNC  
10 MHz REF IN BNC  
8
Air Filter Retainer  
Air Filter Retainer Screw  
9
10 Power Supply Shuttle ID Label  
11 Fan Speed Selector Switch  
12 Inhibit Mode Selector Switch  
13 Power Supply Shuttle Handle (2x)  
Remote Inhibit and Voltage Monitoring Connector  
14 Power Supply Shuttle Mounting Screws (8x)  
Figure 1. Rear View of the NI PXIe-1062Q Chassis  
Installation and Maintenance  
The information in this section is for qualified service personnel only. Read  
the Read Me First: Safety and Radio-Frequency Interference document  
included with your kit before using the power supply shuttle.  
Caution Many components within the NI PXIe-1062Q chassis under repair are susceptible  
to static discharge damage. Service the chassis only in a static-free environment. Observe  
standard handling precautions for static-sensitive devices while servicing the chassis.  
Always wear a grounded wrist strap, or equivalent, while servicing the chassis.  
Caution Always disconnect the AC power cable before cleaning or servicing the chassis.  
© National Instruments Corporation  
3
NI PXIe-1062Q Power Supply Shuttle User Guide  
 
 
Caution Never connect the AC power cable to the power supply shuttle until you install it  
in a NI PXIe-1062Q chassis. Do not use, test, or configure the power supply shuttle outside  
of a chassis.  
The power supply shuttle is a replacement part for the NI PXIe-1062Q  
chassis. The NI PXIe-1062Q User Manual contains all of the most  
up-to-date chassis service procedures, including removal and replacement  
of power supply shuttles. The chassis includes a hardcopy of the  
NI PXIe-1062Q User Manual; additionally, you can download a softcopy  
from ni.com/support.  
Removal  
Before attempting to replace the power supply shuttle, verify that there is  
adequate clearance behind the chassis. With the chassis powered off,  
disconnect the power cable from the power supply shuttle on the back of  
the chassis. Identify the eight mounting screws that attach the power supply  
shuttle to the chassis. Refer to Figure 1 for the mounting screw locations.  
Using a Phillips screwdriver, remove the mounting screws. Pull on the  
two rear handles of the power supply shuttle to remove it from the back of  
the chassis.  
Installation  
Ensure that there is no visible damage to the new power supply shuttle.  
Verify that the housing and connector on the new power supply shuttle  
have no foreign material inside. Remove the protective cap on the  
PXI_CLK10 connector. Install the new power supply shuttle into the  
opening on the rear of the chassis. Install and tighten the eight mounting  
screws with a Phillips screwdriver.  
Configuration  
The fan-speed selector switch is on the rear panel of the power supply  
shuttle. Refer to Figure 1 to locate the fan-speed selector. Select HIGH for  
maximum cooling performance (recommended) or AUTO for quieter  
operation. When set to AUTO, air-intake temperature determines the fan  
speed.  
NI PXIe-1062Q Power Supply Shuttle User Guide  
4
ni.com  
 
Connecting Safety Ground  
Caution The power supply shuttle is designed with a three-position NEMA 5-15  
(IEC 60320) jack that connects the ground line to the chassis ground. To minimize  
shock hazard, make sure the electrical power outlet you use to power the chassis has  
an appropriate earth safety ground.  
If your power outlet does not have an appropriate ground connection, you  
must connect the premise safety ground to the chassis grounding screw.  
Refer to Figure 1 to locate the chassis grounding screw. To connect the  
safety ground, complete the following steps:  
1. Connect a 16 AWG (1.3 mm) wire to the chassis grounding screw  
using a grounding lug. The wire must have green insulation with a  
yellow stripe or must be noninsulated (bare).  
2. Attach the opposite end of the wire to permanent earth ground using  
toothed washers or a toothed lug.  
Specifications  
AC Input  
Input voltage range................................. 100 to 240 VAC  
Operating voltage range1........................ 90 to 264 VAC  
Input frequency ...................................... 50/60 Hz  
Operating frequency range1 ................... 47 to 63 Hz  
Input current rating................................. 8 A  
Over-current protection.......................... 10 A circuit breaker  
Line regulation  
3.3 V................................................ < 0.2%  
5 V................................................... < 0.1%  
12 V .............................................. < 0.1%  
1
The operating range is guaranteed by design.  
© National Instruments Corporation  
5
NI PXIe-1062Q Power Supply Shuttle User Guide  
 
Efficiency................................................70% typical  
Power disconnect....................................The AC power cable provides  
main power disconnect. The  
chassis front-panel power switch  
causes the power supply to  
provide DC power to  
the CompactPCI/PXI backplane.  
DC Output  
DC current capacity (IMP  
)
Voltage  
+3.3 V  
+5 V  
Maximum Current  
26 A  
27 A  
19 A  
1.5 A  
1.5 A  
+12 V  
–12 V  
5 VAUX  
Notes Maximum combined +3.3 V, +5 V, and +12 V power is 345 W.  
Maximum total power is 353.6 W.  
The maximum power dissipated in the system slot should not exceed 140 W.  
The maximum power dissipated in a peripheral slot should not exceed 30 W.  
NI PXIe-1062Q Power Supply Shuttle User Guide  
6
ni.com  
 
Backplane pin current capacity  
Slot  
System Controller Slot  
System Timing Slot  
+5 V  
9 A  
0 A  
6 A  
V (I/O) +3.3 V  
+12 V  
11 A  
2 A  
–12 V  
0 A  
5 VAUX  
1 A  
0 A  
0 A  
5 A  
9 A  
3 A  
6 A  
0 A  
1 A  
Hybrid Peripheral Slot with  
PXI-1 Peripheral  
1 A  
1 A  
0 A  
Hybrid Peripheral Slot with  
PXI-5 Peripheral  
0 A  
6 A  
0 A  
3 A  
6 A  
2 A  
1 A  
0 A  
1 A  
1 A  
0 A  
PXI-1 Peripheral Slot  
11 A  
Load regulation  
Voltage  
Load Regulation  
+3.3 V  
+12 V  
+5 V  
<5%  
<5%  
<5%  
<5%  
–12 V  
Maximum ripple and noise (20 MHz bandwidth)  
Voltage  
+3.3 V  
+12 V  
+5 V  
Maximum Ripple and Noise  
50 mVpp  
120 mVpp  
50 mVpp  
120 mVpp  
–12 V  
Over-current protection.......................... All outputs protected from short  
circuit and overload with  
automatic recovery  
Over-voltage protection  
3.3 V and 5 V.................................. Clamped at 20 to 30% above  
nominal output voltage  
+12 V and –12 V............................. Clamped at 26 to 29 V difference  
between +12 and –12 V outputs  
Power supply shuttle MTTR.................. Replacement in under 5 minutes  
© National Instruments Corporation  
7
NI PXIe-1062Q Power Supply Shuttle User Guide  
 
National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation.  
Refer to the Terms of Use section on ni.com/legal for more information about National  
Instruments trademarks. Other product and company names mentioned herein are trademarks or trade  
names of their respective companies. For patents covering National Instruments products, refer to the  
appropriate location: Help»Patents in your software, the patents.txt file on your CD, or  
ni.com/patents.  
© 2006 National Instruments Corporation. All rights reserved.  
371965A-01  
Oct06  
 

Miele Clothes Dryer T 7744 C User Manual
Milwaukee Drill 6 1 1676 User Manual
Minicom Advanced Systems Switch 5UM60000 User Manual
NAD Stereo Receiver 3240PE User Manual
Nokia Car Speaker MD 3 User Manual
NordicTrack Treadmill 306000 User Manual
NuTone Landscape Lighting 769RL User Manual
Oregon Grinder 511A User Manual
Patton electronic Network Router 3087 User Manual
Patton electronic Surge Protector 536S User Manual