Regulatory Approvals
Canadian EMI Notice
European Notice
MIL-185C/MIL-195C
ꢀ
ATM TWIST
ATM Fiber/UTP Converter
Five-Year Limited Warranty
MIL-185C
MIL-195C
500mA
5VDC
5VDC
ATMꢀTwist
Model: MILꢀ195
ATMꢀTwist
Model: MILꢀ185
therne
UTP
A
C
UTP
A
C
UTP
to
UTP
to
TIVE
TIVE
P
O
P
O
Fiber
WE
Fiber
WE
R
R
F
I
B
F
E
I
B
ATM
R
A
C
E
ATM
R
A
C
TIVE
TIVE
Single-Mode
CONVERTER
Multi-Mode
CONVERTER
Trademarks:
BASE-F
FCC PART 15 CLASS
A
COMPLIANT
FCC PART 15 CLASS
A
COMPLIANT
TX RX
TX RX
To Contact Technical Support:
Installation Guide
This guide includes the following information:
ꢀꢁ"Introduction" on page 2
ꢀꢁ"Installation" on page 3
ꢀꢁ"Configuration Option" on page 4
ꢀꢁ"Specifications" on page 7
Installation Guide MIL-185C/MIL-195C
MIL-195C
Installation
The MIL-195C converter supports full-duplex ATM
Fiber/UTP links. For fiber budget constraints, the MIL-
195C has a launch power of -19 db and a receive
sensitivity of -30 db (using a 1300 nm class 1 laser). In a
full-duplex environment, up to 100m of CAT 5 UTP and
15km single-mode fiber can be used.
To install either converter:
1. Attach the CAT 5 UTP cable from the network to the
RJ-45 port on the device.
Note: Use screened CAT 5 UTP cable for CISPR-22 class B installation.
2. Attach the fiber network cable connectors to the
connectors marked “RX” (Receive) and “TX”
(Transmit).
5VDC
3. Connect the power receptacle from the wall adapter
to the unit.
ATMꢀTwist
Model: MILꢀ195
UTP A
CTIVE
UTP
to
4. Verify that the power LED illuminates.
POWER
Fiber
5. Verify that both the UTP and the FIBER active LEDs
also illuminate when all cables are attached.
FIBER
ATM
Single-Mode
CONVERTER
A
CTIVE
Important notice: This device is set to half duplex mode at the factory. If you are
experiencing excessive collision errors or CRC errors, then you
must force full duplex mode operation on the connecting
FCC PART 15 CLASS A COMPLIANT
TX RX
device(s) before you power up the MiLAN device(s).
Diagnostic LEDs
Figure 4. MIL-195C
• UTP ACTIVE: Illuminates when the device receives a
valid signal from the device connected to the UTP port
Specifications
• POWER: This LED illuminates when the device is
powered up
Storage Temperature
• FIBER ACTIVE: Illuminates when the device receives a
valid signal from the device connected to the fiber port.
• Minimum: -25° C
• Maximum: 75° C
3
6
Installation Guide MIL-185C/MIL-195C
Configuration Options
Special Notes
MIL-185C
The following two figures display the typical network
configuration for the converters.
Power
The MIL-185C converter supports full-duplex ATM
Fiber/UTP links. For network budget constraints, the
MIL-185C has a launch power of -19 db and a receive
sensitivity of -31 db (using a 850 nm class 1 laser). In a
full-duplex environment, up to 100m of CAT 5 UTP and
2km of multi-mode fiber may be used.
RJ-45
5 VDC power
connector
connector
5VDC
UTP cabling
ATMꢀTwist
Model: MILꢀ185
UTP
A
CTIVE
UTP
to
P
O
Fiber
W
E
R
F
I
BE
Switching hub
ATM
R
A
CTIVE
Multi-Mode
CONVERTER
5VDC
FCC PART 15 CLASS
A
COMPLIANT
TX RX
Fiber
cabling
ATMꢀTwist
Model: MILꢀ185
UTP A
CTIVE
Figure 1. Fiber Network to Switching Hub
UTP
to
POWER
Fiber
Power
FIBER
ATM
A
CTIVE
Multi-Mode
CONVERTER
RJ-45
5 VDC power
connector
connector
5VDC
UTP cabling
FCC PART 15 CLASS A COMPLIANT
TX RX
ATMꢀTwist
Model: MILꢀ185
UTP
A
CTIVE
UTP
to
P
O
Fiber
W
E
R
F
I
B
E
Ethernet port
ATM
R
A
CTIVE
Multi-Mode
CONVERTER
Figure 3. MIL-185C
FCC PART 15 CLASS
A
COMPLIANT
TX RX
Fiber
cabling
Figure 2. Fiber Network to Remote—Full-Duplex Workstation
5
4
|