Operating and installation instructions
Frost free fridge freezer
with dynamic cooling
KFN 12943 SD edt/cs
en - GB
To avoid the risk of accidents or
damage to the appliance, it is
essential to read these instructions
before it is installed or used for the
first time.
M.-Nr. 09 290 880
Contents
Freezing and storing food. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Maximum freezing capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Freezing fresh food . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Storing frozen food . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Home freezing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Hints on home freezing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Before placing food in the freezer compartment . . . . . . . . . . . . . . . . . . . . . . . 28
Placing food in the freezer section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Freezer calendar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Ice cubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Cooling drinks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Automatic defrost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Cleaning the interior and accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Appliance doors, side panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Ventilation gaps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Door seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Metal grille at the back of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Noises . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
After Sales / Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Climate range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Aligning the appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Levelling the appliance door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Appliance dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Changing the door hinging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Aligning the appliance doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Building in the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Guide to the appliance
aOn button for the whole appliance
and On/Off button for independently
switching the refrigerator section on
and off
eFreezer section temperature display
fFreezer section temperature selector
button
gSuper freeze button and indicator
light
bDynamic cooling button and
indicator light
hAlarm off button and indicator light
cRefrigerator section temperature
selector button
iMaster switch for switching
the whole appliance on and off
dRefrigerator section temperature
display
4
Guide to the appliance
aDynamic cooling fan
bInterior lighting
cButter and cheese compartment
dEgg tray/Condiment tray
eAdjustable shelf
fCondensate channel and
drain hole
gFruit and vegetable containers
hBottle holder
iBottle shelf
jFreezer drawers with
freezer calendar
5
Caring for the environment
Disposal of the packing
material
Disposal of your old appliance
Electrical and electronic appliances
often contain materials which, if
handled or disposed of incorrectly,
could be potentially hazardous to
human health and to the environment.
They are, however, essential for the
correct functioning of your appliance.
Please do not therefore dispose of it
with your household waste.
The transport and protective packing
has been selected from materials which
are environmentally friendly for
disposal, and should be recycled.
Ensure that any plastic wrappings,
bags etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation!
Please dispose of it at your local
community waste collection / recycling
centre or contact your dealer for
advice. Ensure that it presents no
danger to children while being stored
for disposal.
Take care not to damage the pipework
at the back of it before or during
transportation to an authorised
collection depot.
In this way, refrigerant in the pipework
and oil in the compressor will be
contained, and will not leak out into the
environment.
6
Warning and Safety instructions
dangerous. Miele cannot be held liable
for damage resulting from incorrect or
improper use or operation of the
This appliance complies with all
relevant safety requirements.
Improper use can, however, present
a risk of both personal injury and
damage to property.
appliance.
The appliance can only be used by
~
people with reduced physical, sensory
or mental capabilities, or lack of
To avoid the risk of accidents and
damage to the appliance, please
read these instructions carefully
before using it for the first time. They
contain important notes on
experience and knowledge, if they are
supervised whilst using it, or have been
shown how to use it in a safe way and
understand the hazards involved.
installation, safety, operation and
maintenance.
Safety with children
Children 8 years and older may use
~
Keep these instructions in a safe
place and pass them on to any
future user.
the appliance only if they have been
shown how to use it in a safe way and
understand the hazards involved.
Children under 8 years of age must
be kept away from the appliance unless
they are constantly supervised.
~
Correct application
The appliance is not designed for
~
commercial use. It is intended for use in
domestic households and in similar
working and residential environments
such as:
This appliance is not a toy! To
~
prevent the risk of injury, do not allow
children to play with it or near it, or to
play with the controls, or to swing on
the door.
– Shops
Do not allow children to play with the
~
packaging material, e.g. plastic bags
and wrappings. Danger of suffocation.
– Offices and showrooms
and by residents in establishments
such as:
– Hostels and guest houses.
The appliance is not intended for
outdoor use.
It must only be used as a domestic
appliance to cool and store food as well
as to store deep frozen food, freeze
fresh food and to prepare ice.
Any other usage is not supported by
the manufacturer and could be
7
Warning and Safety instructions
Technical safety
- air the room in which the appliance is
located for several minutes and
- contact the Service Department for
advice.
Before setting up the appliance,
~
check it for any externally visible
damage. Do not install and use a
damaged appliance.
The more coolant there is in an
appliance, the larger the room it should
be installed in. In the event of a
~
It could be dangerous.
If the connection cable is faulty it must
~
leakage, if the appliance is in a small
room, there is the danger of
combustible gases building up.
For every 8 g of coolant at least 1 m3 of
room space is required. The amount of
coolant in the appliance is stated on the
data plate inside the appliance.
only be replaced by a service technician
authorised by the manufacturer to protect
the user from danger.
Safe operation of the appliance is
~
only assured if it has been installed and
connected in accordance with these
operating and installation instructions.
This appliance contains the coolant
Before connecting the appliance,
~
~
Isobutane (R600a), a natural gas which
is environmentally friendly. Although it
is flammable, it does not damage the
ozone layer and does not increase the
greenhouse effect. The use of this
coolant has, however, led to a slight
increase in the noise level of the
appliance. In addition to the noise of
the compressor, you might be able to
hear the coolant flowing around the
system. This is unavoidable, but does
not have any adverse effect on the
performance of the appliance.
make sure that the connection data on
the data plate (voltage and frequency)
matches the mains electricity supply.
This data must correspond in order to
avoid the risk of damage to the
appliance. Consult a qualified
electrician if in any doubt.
Do not connect the appliance to the
mains electricity supply by a
multi-socket adapter or an extension
lead. These do not guarantee the
required safety of the appliance (e.g.
danger of overheating).
~
Care must be taken during the
transportation and installation of the
appliance that no parts of the cooling
system are damaged. Leaking coolant
can damage the eyes.
In the event of any damage:
- avoid open flames and anything which
creates a spark,
- disconnect from the mains,
8
Warning and Safety instructions
The electrical safety of this
~
appliance can only be guaranteed
The appliance must be isolated from
~
the electricity supply during installation,
when it is correctly earthed. It is most
important that this basic safety
maintenance and repair work.
Faulty components must only be
~
requirement is observed and regularly
tested and where there is any doubt,
the household wiring system should be
inspected by a qualified electrician.
The manufacturer cannot be held liable
for damage or injury caused by the lack
of or inadequacy of an effective
replaced by genuine Miele original
spare parts. The manufacturer can only
guarantee the safety of the appliance
when Miele replacement parts are
used.
The appliance must not be used in a
~
non-stationary location (e.g. on a ship).
earthing system (e.g. electric shock).
Installation, maintenance and
repairs may only be carried out by a
suitably qualified and competent
In areas which may be subject to
~
~
infestation by cockroaches or other
vermin, pay particular attention to
person in strict accordance with current keeping the appliance and its
national and local safety regulations.
Repairs and other work by unqualified
persons could be dangerous. The
manufacturer cannot be held liable for
unauthorised work.
surroundings clean at all times. Any
damage caused by cockroaches or
other vermin will not be covered by the
guarantee.
While the appliance is under
~
guarantee, repairs should only be
undertaken by a service technician
authorised by the manufacturer.
Otherwise the guarantee will be
invalidated.
9
Warning and Safety instructions
Correct use
Do not store cans or bottles
containing carbonated drinks or liquids
which could freeze in the freezer. The
cans or bottles could explode. Danger
of injury and damage to the appliance.
~
Do not handle frozen food with wet
~
hands. Your hands may freeze to the
frozen food. Danger of frost burn.
Do not take ice cubes out with your
~
When cooling drinks quickly in the
~
bare hands and never place ice cubes
or ice lollies in your mouth straight from
the freezer.
The very low temperature of the frozen
ice or lollies can cause frost burn to the
lips and tongue.
freezer, make sure bottles are not left in
for more than one hour; otherwise they
could burst. Danger of injury and
damage to the appliance.
Observe the "use-by" dates given on
~
food to avoid the risk of food poisoning.
Storage times will depend on several
factors, including the freshness and
quality of the food as well as the
temperature at which it is stored. Follow
the instructions given on the food
Do not refreeze partially or fully
~
defrosted food. Consume defrosted
food as soon as possible, as it will lose
its nutritional value and spoil if left for
too long. Defrosted food may only be
re-frozen after it has been cooked.
manufacturer's packaging regarding
storage conditions and "use-by" dates.
Do not store explosive materials in
~
the appliance or any products
containing propellants (e.g. spray
cans). Thermostats switching on may
produce sparks which could present a
fire hazard. Flammable compounds
could explode.
Do not use sharp edged objects to
~
– remove frost and ice,
– separate frozen foods and remove
ice trays.
They will damage the evaporator,
causing irreversible damage to the
appliance.
Do not operate any electrical
~
equipment (e.g. an electric ice-cream
maker) inside the appliance. Danger of
sparking and explosion.
Do not place electric heaters or
~
candles in the appliance to defrost it.
These will damage the plastic parts.
If storing alcohol with a high
~
percentage proof in the refrigerator,
make sure the bottle is tightly closed
and stored upright. Danger of
explosion.
Do not use defrosting sprays or
~
de-icers, as they might contain
substances which could damage the
plastic parts or which could cause the
build-up of gases and pose a danger to
health.
10
Warning and Safety instructions
Do not use a steam-cleaning
Stainless steel appliances
~
appliance to defrost or clean the
appliance. Steam could reach
electrical components and cause a
short circuit.
Do not use sticky notes, transparent
~
adhesive tape, masking tape or other
types of adhesive on the surface of the
door.
Do not use any oils or grease on the These damage the surface, causing it
to lose its dirt-repellent protective
coating.
~
door seals, as these will cause the
seals to deteriorate and become
porous with time.
The high-quality surface of the door
If storing food which contains a lot of is susceptible to scratching.
fat or oil in the appliance or the
~
~
Even fridge magnets can cause
refrigerator door, make sure that it does scratching.
not come into contact with plastic
components as this could cause stress
Disposal of your old appliance
cracks.
Before disposing of an old
~
appliance, first make the door latch or
lock unusable.
Do not block the ventilation gaps in
~
the appliance as this would impair the
efficiency of the appliance, increase the
electricity consumption and could
cause damage to the appliance.
This way you will prevent children from
accidentally locking themselves in and
endangering their lives.
The appliance is designed for use
~
Be careful not to damage any part of
the pipework whilst awaiting disposal,
e.g. by
~
within certain climate ranges (ambient
temperatures), and should not be used
outside this range. The climate range
for your appliance is stated on the data
plate inside the appliance.
– puncturing the refrigerant channels
in the evaporator.
Installing it in a room with too low an
ambient temperature, e.g. a garage,
can lead to the appliance switching off
for longer periods so that it cannot
maintain the required temperature.
– bending any pipework.
– scratching the surface coating.
Splashes of refrigerant can damage the
eyes.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
11
How to save energy
Normal energy
consumption
Increased energy
consumption
Installation site
In a ventilated room.
In an enclosed, unventilated room.
In direct sunlight.
Protected from direct sunlight.
Not near to a heat source (radiator, Near to a heat source (radiator,
oven).
oven).
Where the ideal ambient room
temperature is approx. 20°C.
Where there is a high ambient room
temperature.
Do not cover the ventilation gaps
and dust them regularly.
Temperature setting
with a thermostat
which is approximate
(set in stages).
With a medium setting of 2 to 3.
With a high setting: the lower the
temperature in the compartment, the
higher the energy consumption.
Temperature setting
with a thermostat which
is exact to the degree
(digital display).
Larder section 8 to 12 °C
On appliances with winter setting,
please make sure that the winter
setting is switched off when the
ambient temperature is warmer than
16 °C .
Refrigerator section 4 to 5 °C
PerfectFresh zone just above 0 °C
Freezer section -18 °C
Wine storage section 10 to 12 °C
Use
Drawers, shelves and racks
arranged as they were when the
appliance was delivered.
Only open the door when necessary Frequent opening of the door for
and for as short a time as possible. long periods will cause a loss of
coldness.
Store food in an organised way.
Searching for an item will mean the
door is open for longer.
Allow hot food and drinks to cool
down before placing them in the
appliance.
Hot food will cause the compressor
to run for a long time, as the
appliance will have to work harder
to reduce the temperature.
Store food covered or packaged.
The evaporation or condensation of
liquids will cause a loss of coldness
in the refrigerator.
Place frozen food in the refrigerator
to defrost.
Do not over-fill the appliance to
allow air to circulate.
Defrosting
Defrost the freezer section when a A layer of ice hinders the cold from
layer of ice 0.5 cm thick (maximum) reaching the frozen food, and
has built up.
increases energy consumption.
12
Switching on and off
Before using for the first time
Switching on
The refrigerator and freezer sections are
switched on together by pressing the
master switch on the right hand side of
the control panel, or by pressing the On
button on the left hand side of the
control panel.
Protective foil
The stainless steel trim to the interior
shelves and the door shelves has a
layer of protective foil to prevent
damage during transportation.
On stainless steel appliances, the outer
surfaces are also covered with
protective foil.
^ Do not remove the foil until the
appliance has been positioned in its
final location.
^ Press the master switch on the right
hand side of the control panel.
The temperature display for the
refrigerator section will show the
Cleaning and care
selected temperature setting. The
temperature display for the freezer and
the alarm indicator light will flash until
the freezer section has cooled down to
the correct temperature for freezing.
^ Treat the stainless steel trim to the
interior shelves and the door shelves
with the Miele stainless steel
conditioning agent supplied as soon
as you have removed the foil.
The appliance will start cooling down
and the interior light in the refrigerator
section will come on if you open the
door.
^ On stainless steel appliances also
treat the side panels with the Miele
stainless steel conditioning agent
supplied as soon as you have
removed the protective foil. The
appliance doors have a special finish
which is resistant to soiling. Do not
use Miele stainless steel conditioning
agent on the appliance doors.
To enable the temperature to get
sufficiently cold inside the
appliance, allow the appliance to
run for a few hours before placing
food in it.
Do not place food in the freezer until
the temperature is at least -18 °C.
Important. Miele stainless steel
conditioning agent provides a
protective coating which helps
prevent resoiling.
^ Clean the inside of the appliance and
the accessories with lukewarm water
and a little washing up liquid, and then
dry with a soft cloth.
13
Switching on and off
Switching off
section will start cooling. The interior
light will come on when the door is
opened.
Switching off for longer
periods of time
^ Press the master switch on the right
hand side of the control panel until
both temperature displays go out.
If the appliance is not going to be used
for a longer period of time, e.g. whilst
on holiday:
The interior lighting will not come on
when you open the door and the
cooling process will be switched off.
^ switch the appliance off,
^ disconnect it from the mains,
^ clean the appliance out and
^ leave the doors ajar to air it.
To switch the refrigerator section off
separately
The refrigerator section can be
switched off without having to switch off
the freezer section. This is useful e.g.
whilst on holiday.
If, during a long absence, the
appliance is switched off but not
cleaned out and the doors are left
shut, there is a danger of mould and
odours building up inside the
appliance.
^ Press the On/Off button for the
refrigerator section on the left hand
side of the control panel until the
temperature display for the
refrigerator section goes out.
The interior light will not come on when
you open the door and the refrigerator
section is switched off.
The temperature display for the freezer
section will remain lit up.
To switch the refrigerator section on
again
^ Press the On/Off button on the left
hand side of the control panel again.
The refrigerator section temperature
display will light up. The refrigerator
14
The correct temperature
It is very important to set the correct
temperature for storing food in the
appliance. Micro-organisms will cause
food which is not stored at the correct
temperature to deteriorate rapidly.
Temperature influences the growth rate
of these micro-organisms. Reducing
the temperature reduces their growth
rate.
. . . in the freezer section
To freeze fresh food and to store frozen
food for a long time, a temperature of
-18 °C is required. At this temperature
the growth of micro-organisms is
generally halted. As soon as the
temperature rises above -10 °C, the
micro-organisms become active in the
food again so that it cannot be kept as
long. For this reason, partially defrosted
or defrosted food must not be re-frozen.
Food may be re-frozen once it has
been cooked, as the high temperatures
achieved when cooking destroy most
micro-organisms.
The temperature in the appliance will
rise:
– the more often the door is opened
and the longer it is kept open,
– the more food that is placed in it,
– the warmer the food is which is being
put into it,
Setting the temperature
The temperature is set in each zone by
using the respective temperature
button.
– the higher the ambient temperature
surrounding the appliance.
The appliance is designed for use in
specific ambient temperatures
(climate ranges). Do not use in
ambient temperatures for which it is
not designed.
^ Press the temperature button
repeatedly until the indicator light for
the temperature you want lights up in
the display.
. . . in the refrigerator section
We recommend a temperature of 5 °C
in the middle of the refrigerator.
The first time you press the button the
indicator light for the last temperature
you set will flash in the display.
Thereafter the temperature value will
change each time you press the button
until the highest setting is reached. It
will then go back to the lowest setting
again.
15
The correct temperature
The newly selected temperature will be Temperature display
adopted automatically after a short
The temperature display on the
control panel always shows the
required temperature.
while.
The indicator for the temperature which
has been set for the refrigeration
section will light up.
The indictator for the temperature which Temperature range
has been set for the freezer section will
flash until that temperature is reached.
The temperature can be adjusted:
– In the refrigerator section from 1 °C
to 9 °C.
The temperature can be set to be
slightly colder than the temperature
range shown on the control panel for
the refrigeration and freezer
sections.
– In the freezer section from from
-15 °C to -32 °C.
The ambient temperature in the room
and the installation location can affect
the time it takes for the appliance to
reach the lowest temperature. If the
ambient temperature is too high, the
appliance may not reach the lowest
temperature.
The following example shows how to
set the freezer section temperature
lower than -15 °C but not as cold as
-18 °C:
^ Press the temperature button
repeatedly until the indicator light for
-15 °C lights up in the display.
The relevant temperature indicator
light will flash if a different
temperature is being set.
^ Press it again for approx. 5 seconds
to set the temperature below - 15 °C.
The freezer section temperature
indicator light will also flash if
The temperature has now been set
between -15 °C and -18 °C. However,
this is not visible in the temperature
display.
– the temperature in the freezer
section is not within the possible
temperature range.
– the temperature in the freezer
section has risen by several degrees,
indicating that it is warming up too
much.
The alarm off indicator will flash at the
same time.
16
The correct temperature
This loss of coldness is no cause for
concern in the following circumstances:
– when the door has been left open for
a while, e.g. for removing or storing a
large amount of food,
– when fresh food is being frozen.
However, if the temperature in the
freezer section remains above
-18 °C for a long time, check that the
frozen food has not started to
defrost. If it has, check that the food
is safe to use and if it is, then use it
as soon as possible.
17
Alarm
Your appliance has been fitted with a
warning system which ensures that the
temperature in the freezer section
cannot rise unnoticed and to avoid
energy being wasted if a door is left
open.
If the temperature inside the
appliance is warmer than -18°C for a
longer period of time, check that the
food has not started to thaw or
defrost. If it has, check that it is still
safe to eat, and use it as quickly as
possible.
Activating the alarm system
The alarm system is always active. It
does not have to be switched on
manually.
Once the set temperature has been
reached in the freezer section, the
alarm switches off and the temperature
display and the alarm off indicator will
stop flashing and light up constantly.
Temperature alarm
If the freezer section temperature
becomes too warm, an alarm will sound
and the freezer section temperature
display and the alarm off indicator light
will flash.
The temperature the appliance is set at
determines the temperature the
appliance recognises as being too
warm.
Door alarm
The alarm will sound if a door is left
open for more than 60 seconds.
The alarm will stop as soon as the door
is closed.
Switching the alarm off early
If the noise disturbs you, you can
switch the alarm off early if you wish.
The alarm will sound and the
temperature display and alarm off
indicator light will flash, for example,
^ Press the alarm off button.
– if the freezer door has been left open
for a while, e.g. in order to load, to
re-arrange or to take food out.
The alarm will stop.
The temperature display and the
alarm off indicator light will continue
to flash until the set temperature has
been reached.
– when freezing large amounts of food
at once.
– in the event of a power cut.
– the appliance is faulty.
18
Super freeze and Dynamic cooling
Super freeze
Switching off Super freeze
Switch the Super freeze function on
before putting fresh food into the
freezer.
The Super freeze function will switch off
automatically after approx. 65 hours.
The indicator light will go out and the
appliance will run at normal power
again.
This helps food to freeze quickly and
retain its nutrients, vitamins, flavours
and appearance.
To save energy the Super freeze
function can be switched off once a
constant temperature of -18°C or
colder has been reached in the freezer.
Super freeze is not necessary:
– when placing food in the freezer that
is already frozen.
^ Press the Super freeze button. The
Super freeze indicator light will go
out, and the appliance will continue
to operate at normal power.
– when freezing up to 2 kg fresh food
daily.
Switching on Super freeze
When freezing small quantities of food
in the freezer, the Super freeze function
should be switched on 6 hours
beforehand. When freezing the
maximum load of food the Super
freeze function should be switched on
24 hours beforehand.
^ Press the Super freeze button. The
Super freeze indicator light will come
on.
The appliance works at full power to
lower the temperature in the appliance.
19
Super freeze and Dynamic cooling
Dynamic cooling m
Make sure the fan at the back of the
appliance is not restricted to ensure
unhindered air circulation.
When the Dynamic cooling function is
not switched on, the natural circulation
of air in the appliance will cause
different temperature zones in the
refrigerator as the cold, heavy air will
sink to the lowest section of the
appliance. You should bear this in mind
when placing food in the appliance
(see "Using the refrigerator efficiently").
However, if you are placing a large
amount of food in the refrigerator at any
one time, it is a good idea to switch on
Dynamic cooling. This way you can
distribute the temperature inside the
appliance to all areas more evenly so
that all the food will be chilled to about
the same degree.
Switching off Dynamic cooling
^ Press the Dynamic cooling button
m. The Dynamic cooling indicator
light will go out.
The fan automatically switches off
when the door is open.
The temperature is set as normal with
the temperature control.
Dynamic cooling should also be
selected when:
– the ambient temperature in the room
is high (above approx. 30 °C), and
– the room humidity level is high.
Switching on Dynamic cooling
^ Press the Dynamic cooling button.
The Dynamic cooling indicator light
will come on.
20
Using the refrigerator efficiently
Different storage zones
– pre-packed vegetables and other
fresh food with a label stating it
Due to the natural circulation of the air
in the appliance, there are different
temperature zones in the refrigerator.
Cold, heavy air sinks to the lowest
section of the appliance. Make use of
the different zones when placing food
in the appliance.
should be kept at a temperature of
approx. 4 °C.
Do not store explosive materials in
the appliance or any products
containing propellants (e.g. spray
cans). Danger of explosion.
This appliance has Dynamic
cooling, which helps to keep an
even temperature when the fan is
running. When Dynamic cooling is
switched on, the difference between
the various zones is less
If storing alcohol with a high
percentage proof, make sure it is
tightly closed, and store upright.
pronounced.
If storing food which contains a lot of
oil or fat in the refrigerator or
refrigerator door, make sure it does
not come into contact with plastic
components as this could cause
stress cracks.
Warmest area
The warmest area is in the top section
of the door. Use this for storing butter
and cheese.
Food must not touch the back wall of
the refrigerator, as it may freeze to
the back wall.
Coldest area
The coldest area in a refrigerator is
directly above the vegetable
containers.
To allow air to circulate efficiently,
do not pack food too closely
together in the refrigerator. Do not
cover the fan in the rear wall of the
refrigerator, as this is essential for
keeping the appliance cool.
Use this for all delicate and highly
perishable food, e.g.
– fish, meat, poultry,
– sausage products, ready meals,
– dishes or baked goods containing
eggs or cream,
– fresh dough, cake mixtures, pizza or
quiche dough,
– soft cheese and other dairy
products,
21
Using the refrigerator efficiently
Food which should not be
stored in a refrigerator
Storing food correctly
Food should generally be stored
covered or packaged. This will prevent
food smells from affecting other foods,
food from drying out, and also any
cross-contamination of bacteria. The
growth of bacteria, such as salmonella,
can be avoided by setting the correct
temperature and maintaining good
standards of hygiene.
Not all food is suitable for refrigeration,
as some food is sensitive to cold.
Cucumbers, for example, become
glassy, aubergines bitter and potatoes
sweet. Tomatoes and oranges lose their
aroma, and the peel on citrus fruit
hardens.
Food which should not be stored in a
refrigerator includes:
Fruit and vegetables
– pineapple, pomegranate, bananas,
avocado, mangos, papaya, passion
fruit, citrus fruit
Fruit and vegetables may be stored
loose in the vegetable containers.
Please be aware that not all types of
fruit and vegetables are suitable for
storing in the same container. Aromas
and flavours can transfer from one type
of food to another (e.g. carrots absorb
the smell and flavour of onions very
easily). Some food also gives off a
natural gas (ethylene) which speeds up
the rate at which other food perishes.
– fruit which is not yet ripe
– aubergines/egg plant, cucumbers,
potatoes, peppers/capsicum,
tomatoes, courgettes,
– some hard cheeses, e.g. Parmesan
When shopping for food
– Examples of fruit and vegetables
which produce a large amount of
this natural gas are:
The freshness of food when first placed
in the appliance is an important factor
in determining how long it stays fresh,
and how long it can be kept in the
refrigerator. Time out of the refrigerator,
e.g. during transportation, should be
kept to a minimum. For example, do not
allow food to stay in a hot car for too
long. Once food has started to
Apples, apricots, pears, nectarines,
peaches, plums, avocado, figs,
blueberries, melons and beans.
deteriorate, this process cannot be
reversed. As little as two hours outside
the refrigerator can cause food to start
deteriorating.
22
Using the refrigerator efficiently
– Examples of fruit and vegetables
Meat
which react strongly to the natural
gases given off by other types of
fruit and vegetables are:
Meat should be stored unwrapped.
(Undo wrappings slightly to leave meat
loosely covered, and leave containers
open). This permits air to circulate
Kiwis, broccoli, cauliflower, brussels
sprouts, mangos, honeydew melons, around the meat, allowing the surface
apples, apricots, cucumbers,
tomatoes, pears, nectarines and
peaches.
to dry slightly, which helps prevent the
growth of bacteria. To prevent the risk
of bacterial cross-contamination and
meat deteriorating, do not let one type
of meat come into direct contact with
another type.
Example: Broccoli should not be
stored with apples, as apples
produce a large amount of natural
gas to which broccoli is very
sensitive. The result is a shorter than
expected storage time for the
broccoli.
Unpacked meat and vegetables
Unpackaged meat and vegetables
should be stored separately. To avoid
any microbiological cross-
contamination, these foods may only be
stored together if they are wrapped.
Protein rich foods
Please note that foods rich in protein
deteriorate faster than others.
Shellfish, for example, deteriorates
faster than fish, and fish deteriorates
faster than meat.
23
Adjusting the interior fittings
Moving the shelves
To move the split shelf:
The shelves in the refrigerator section
can be adjusted according to the
height of the food.
^ Take both halves of the split glass
shelf out,
^ Raise the shelf, and pull it forwards
slightly until the notch at the side is in
line with the shelf support. It can then
be raised or lowered to the required
level.
The raised edge at the back must face
upwards to prevent food from touching
the back of the appliance and freezing
to it.
^ fit the two brackets onto the supports
on either side at the required height,
Stoppers prevent the shelves from
being dislodged by mistake.
^ and push the glass shelves in one
after the other.
The shelf with the raised edge must
be at the back.
Split shelf
In order to accommodate tall items in
the appliance, one of the shelves is
divided. The front section can be
pushed under the rear section.
Fruit and vegetable containers
on rollers
The fruit and vegetable containers are
pushed in and out on rollers, and can
be completely removed if necessary.
The rollers can also be removed for
cleaning.
^ Push the rear half of the glass shelf
up slightly from below.
^ At the same time, pull the front half of
the glass shelf forwards slightly and
then push it carefully under the rear
half.
24
Adjusting the interior fittings
Adjusting the condiment
tray/bottle shelf
Universal container
The universal container can be used
both to store and serve food.
^ Lift the tray/shelf up and out of the
stainless steel frame to remove.
^ Push up the stainless steel frame,
and remove.
^ Replace the frame at the required
height. Ensure that it is securely
pushed back into position.
It consists of a deep tray a and a
shallow tray b. Both trays fit the
stainless steel frame.
If you wish to use the universal
container to serve food,
^ place the shallow tray b in the
stainless steel frame, and use the
deep tray as a lid a.
^ Some stainless steel frames are
easier to remove and replace if you
put your hand behind the back bar of
the frame and lift it upwards.
You can lift the universal container,
including contents, out of the frame and
take it to the table.
^ Replace the tray/shelf in the frame.
The tray/shelf can be removed
completely and used as a serving tray
at the table.
Moving the bottle divider
The bottle divider can be moved to the
left or right to ensure that bottles are
held securely in position when the door
is opened and shut.
The bottle divider can be removed
completely (e.g. for cleaning).
^ To do this, push up the front edge of
the bottle divider, and disengage it.
25
Freezing and storing food
Maximum freezing capacity
Storing frozen food
To ensure that fresh food placed in the
freezer freezes through to the core as
quickly as possible, the maximum
freezing capacity must not be
exceeded. The maximum freezing
capacity for freezing within a 24-hour
period is given on the data plate:
"Freezing capacity ....kg/24 hrs".
When buying frozen food to store in
your freezer, check
– that the packaging is not damaged,
– the use-by date,
– the temperature at which the frozen
food is being stored in the shop. The
length of time it can be kept is
The maximum freezing capacity given
on the data plate has been calculated
according to DIN EN ISO 15502 Stan-
dard.
reduced if it has been stored at a
temperature warmer than -18 °C.
^ Buy frozen food once you have
finished the rest of your shopping,
and wrap it in newspaper or use a
cool bag or cool box to transport it.
Freezing fresh food
Fresh food should be frozen as quickly
as possible. This way the nutritional
value of the food, its vitamin content,
appearance and taste are not impaired.
^ Store it in the freezer as soon as
possible.
Never re-freeze partially or fully
defrosted food. Consume defrosted
food as soon as possible as it will
lose its nutritional value and spoil if
left for too long. Defrosted food may
only be re-frozen after it has been
cooked.
Food which takes a long time to freeze
will lose more water from its cells, which
then shrink.
During the defrosting process, only
some of this water is reabsorbed by the
cells; the rest collects around the food.
In practice this means that the food
loses a large degree of its moisture.
You can tell if this has happened by the
amount of liquid around the food.
If food is frozen quickly, the cells have
less time to lose moisture, so they
shrink less. As there is not so much
moisture loss, it is easier for the food to
reabsorb it during the defrosting
process, and very little water collects
around the defrosted food.
26
Freezing and storing food
Home freezing
– Do not season fresh food or
blanched vegetables before
Only freeze fresh food which is in a
good condition.
freezing. Only season cooked food
lightly before freezing, but care
should be taken as the taste of some
spices alters when frozen.
Hints on home freezing
– The following types of food are
suitable for freezing:
– Do not place hot food or drinks in the
freezer. This causes already frozen
food to thaw, and increases the
energy consumption considerably.
Allow hot food and drinks to cool
down before placing them in the
freezer.
Fresh meat, poultry, game, fish,
vegetables, herbs, fresh fruit, dairy
products, pastry, leftovers, egg
yolks, egg whites and a range of
pre-cooked meals.
– The following types of food are not
suitable for freezing:
Packaging
Grapes, lettuce, radishes, sour
cream, mayonnaise, eggs in their
shells, onions, whole raw apples and
pears.
^ Freeze food in portions.
Unsuitable packaging material
- wrapping paper
- grease-proof paper
- cellophane
- bin bags
- plastic carrier bags
– To retain colour, taste and vitamin C,
vegetables should be blanched after
they have been trimmed and
washed.
To blanch: bring a large saucepan of
water to the boil, immerse the
vegetables in the fast boiling water
for 2-3 minutes, depending on
variety. Remove, and plunge into
ice-cold water to cool quickly. Drain
and pack ready for freezing.
Suitable packaging material
- plastic freezer film
- freezer bags
- aluminium foil
- freezer containers
^ Expel as much air as possible from
bags etc. before sealing them, to
prevent freezer-burn on food.
– Lean meat freezes better than fatty
meat, and can be stored for
considerably longer.
^ Close the packaging tightly with
- rubber bands
- plastic clips
- string or bag ties
- freezer tape.
– To prevent chops, steaks, cutlets or
rolled meat from freezing together in
solid blocks when packed, separate
with a sheet of plastic freezer film.
Freezer bags may also be sealed
using home heat sealing kits.
27
Freezing and storing food
^ Make a note of the contents and the
date of freezing on the packaging.
Please note that when removing the
drawers, the lowest freezer drawer
must always remain in the freezer.
When placing food on the glass cold
plate make sure it does not obstruct
the ventilation gaps at the back.
This is important for problem-free
operation and normal energy
consumption.
Before placing food in the freezer
section
^ When freezing more than 2 kg of
fresh food, switch on the Super
freeze function some time before
placing the food in the freezer (see
"Super freeze").
This also helps food that is already in
the freezer to stay frozen.
– Freezing the maximum amount
(see data plate)
^ Remove the upper freezer drawers.
Placing food in the freezer section
^ Place the food flat on the upper glass
cold plates so that it freezes through
to the core as quickly as possible.
The following maximum capacities
must be observed:
– freezer drawer = 25 kg
– glass cold plate = 35 kg
Once frozen:
^ Place the frozen food in the freezer
drawers and push them back into the
appliance.
Food to be frozen must on no
account touch food which is already
frozen to avoid partial thawing.
– Large items
^ Make sure that the packaging and
containers are dry to prevent them
sticking together when frozen.
If you wish to freeze large items such
as a turkey or game, the glass cold
plates between the drawers can be
removed.
– Freezing small amounts of food
^ Remove the upper freezer drawers
and carefully lift and slide out the
glass cold plates.
Place the food in the upper freezer
drawers.
^ Place the food flat in the bottom of
the drawers so that it freezes through
to the core as quickly as possible.
28
Freezing and storing food
Freezer calendar
Defrosting
The freezer calendar on the freezer
drawer gives the length of time in
months which various foods can be
stored for effectively.
Frozen food can be defrosted in
different ways:
– in a microwave oven,
– in an oven using the "Fan" or
"Defrost" setting,
Where the storage time given on the
packaging differs, follow the advice on
the packaging.
– at room temperature,
– in the refrigerator (the cold given off
by the frozen food helps to keep the
other food cold),
– in a steam oven.
Poultry It is particularly important to
observe food hygiene rules when
defrosting poultry. Do not use the liquid
from defrosted poultry. Pour it away
and wash the container it was in, the
sink and your hands. Danger of
salmonella poisoning.
2-3 months:
Cakes, ice cream, stew
3-5 months:
Fish, mushrooms, bread
6-8 months:
Pork, veal, poultry
Ensure that meat and fish (e.g mince,
chicken, fish fillets) do not come into
contact with other foods while
defrosting. Catch the liquid and
dispose of it carefully.
10-12 months:
Beef, fruit, vegetables
Fruit should be defrosted at room
temperature in its packaging, or in a
covered bowl.
Most vegetables can be cooked while
still frozen. Just put straight into boiling
water or hot fat. The cooking time is
slightly less than that of fresh
vegetables due to changes in the cell
structure.
29
Freezing and storing food
Do not re-freeze partially or fully
defrosted food. Consume defrosted
food as soon as possible as it will
lose its nutritional value and spoil if
left for too long. Defrosted food may
only be re-frozen after it has been
cooked.
Ice cubes
^ Fill the ice tray three quarters full with
water, and place it in the bottom of
one of the drawers.
^ Once frozen, use a blunt instrument,
for example a spoon handle, to
remove the ice tray from the freezer.
^ Ice cubes can be removed easily
from the tray by twisting the tray
gently or by holding it under cold
running water for a short while.
Cooling drinks
Do not store cans or bottles containing
carbonated drinks or liquids which
could freeze in the freezer. The cans or
bottles could explode.
When cooling non-carbonated drinks
quickly in the freezer, make sure bottles
are not left in for more than one hour,
otherwise they could burst.
30
Automatic defrost
Refrigerator section
Freezer section
The refrigerator defrosts automatically.
This appliance is equipped with a "Frost
free" system. The freezer section
defrosts automatically.
Condensate and frost can build up on
the back wall of the refrigerator section
whilst it is in use. You do not need to
remove this, as it will defrost and
evaporate automatically with the
The moisture generated in the
appliance collects on the condenser
and is automatically defrosted and
dissipated from time to time.
warmth generated by the appliance.
The condensate is drained away via a
channel and drain hole into an
evaporation system at the back of the
appliance.
This automatic defrosting system
enables the freezer section to remain
permanently ice-free, however, the food
stored in the freezer section will not
defrost.
Ensure that the condensate channel
and drain hole are kept clean and
are never blocked so that
condensate can flow away without
hindrance.
31
Cleaning and care
A range of Miele branded cleaning
and conditioning products is
available to order from Miele or
Unlike stainless steel cleaning
agents, the conditioning agent does
not contain any abrasive substances
and will gently remove soiling. Each
time it is used, it forms a water and
dirt repellent protective coating.
Make sure that no water can
penetrate into the electronic unit or
into the light.
To avoid damaging the surface of
your appliance, do not use:
Do not let water get into the
condensate channel and drain hole
when cleaning.
– cleaning agents containing soda,
ammonia, acids or chlorides,
– cleaning agents containing
descaling agents,
Do not use steam cleaning
apparatus to clean the appliance.
Steam could reach electrical
components and cause a short
circuit.
– abrasive cleaning agents, e.g.
powder cleaners and cream
cleaners,
– solvent-based cleaning agents,
– stainless steel cleaning agents,
– dishwasher cleaner,
The data plate located inside the
appliance must not be removed. It
contains information which is required
in the event of a service call.
– oven sprays,
– glass cleaning agents,
The stainless steel doors have a
special finish which is resistant to
soiling.
– hard, abrasive sponges and
brushes, e.g. pot scourers,
– melamine eraser blocks,
– sharp metal scrapers.
Do not treat the doors with stainless
steel conditioning agent as this will
cause noticeable smearing.
Before cleaning
However, do use Miele stainless
steel conditioning agent to treat the
other stainless steel surfaces of the
appliance (available from Miele or
www.miele-shop.com).
^ Switch the appliance off.
^ Disconnect it from the mains.
^ Take any food out of the appliance
and store it in a cool place.
^ Take out any removable parts, e.g.
shelves, for cleaning.
32
Cleaning and care
^ The bottle shelf and condiment tray in Cleaning the interior and
the door can be removed from their
stainless steel frames for cleaning.
accessories
^ Clean the appliance at least once a
month.
To remove the stainless steel trim from
the lid of the butter and cheese
compartment (in the top of the door),
proceed as follows:
Remove soiling immediately to
prevent it from drying on.
^ Take the butter and cheese
compartment out of the refrigerator
section.
Use lukewarm water with a little
washing-up liquid.
The following are dishwasher safe:
^ Open the lid of the compartment.
– the butter dish, egg trays, ice cube
tray (supplied as standard,
depending on model)
The stainless steel trim is a tight fit
across the plastic lid and will require
sufficient force to detach it.
– the bottle shelf and condiment tray in
the door (removed from their stainless
steel frames)
– the butter and cheese compartment
(with the stainless steel trim removed)
The stainless steel frames and the
stainless steel trim on the butter and
cheese compartment in the door are
not suitable for cleaning in a
dishwasher.
^ Detach the stainless steel trim from
the edge of the lid (1.) at one side
and remove.
^ Press the white plastic stoppers out
of notches (2.).
The temperature of the dishwasher
programme must not exceed 55 °C.
Contact with some foodstuffs, such
as carrots, tomatoes or ketchup can
cause plastic items to discolour.
However, this discolouration will not
affect the stability of plastic items.
^ After cleaning, refit the stainless steel
trim onto the lid in the reverse order.
^ Clean the interior shelves and
drawers by hand. These are not
suitable for cleaning in a dishwasher.
33
Cleaning and care
^ Clean the condensate channel and
drain hole frequently, so that
condensate can drain away
unhindered. Use a straw or similar to
clear the drain if necessary.
^ The surfaces should be cleaned
using a solution of hot water and a
little washing-up liquid applied with a
soft sponge. They can also be
cleaned with a damp microfibre cloth
(without using any cleaning agent).
^ After cleaning, wipe the interior and
accessories with a damp cloth and
dry with a soft cloth.
^ After cleaning, wipe with a damp
cloth and dry with a soft cloth.
Leave the doors open to air the
appliance for a short while.
Stainless steel appliances
– Appliance doors
^ Miele stainless steel conditioning
agent can be used to remove any
soiling.
The appliance doors have a high
quality, special finish which is resistant
to soiling and is very easy to clean.
^ It is important to treat the stainless
steel frames and trim with Miele
stainless steel conditioning agent
each time they are cleaned. This will
protect the surface and help prevent
resoiling.
Do not use the following to
clean/condition the doors
– stainless steel cleaning agent:
this will damage the surface.
– Miele stainless steel conditioning
agent:
Appliance doors, side panels
this will cause noticeable smearing.
Remove any soiling on the
appliance doors and side panels im-
mediately.
If this is not done, it might become
impossible to remove and could
cause the surface to alter or
discolour.
– Side panels
^ Use Miele stainless steel conditioning
agent to remove any soiling from
stainless steel surfaces.
^ Make sure you treat the side panels
with Miele stainless steel conditioning
agent each time you clean them.
This will give them a water and dirt
repellent protective coating and help
prevent re-soiling.
All surfaces are susceptible to
scratching.
Contact with unsuitable cleaning
agents can alter or discolour the
surfaces.
34
Cleaning and care
Ventilation gaps
After cleaning
^ The ventilation gaps should be
cleaned regularly with a brush or
vacuum cleaner. A build-up of dust
will increase the energy consumption
of the appliance.
^ Replace all shelves and accessories
in the refrigerator section.
^ Put the food back in the refrigerator.
^ Reconnect the appliance to the
mains and switch it back on.
Door seals
^ Switch on the Super freeze function
so that the freezer can cool down
quickly.
Do not use any oils or grease on the
door seals as these will cause the
seals to deteriorate and become
porous over time.
^ Once the freezer has reached the
required temperature, place the food
back in the freezer drawers and put
them back in the freezer.
The door seals should be cleaned
regularly with clean water, and then
wiped dry with a soft cloth.
^ Switch off the Super freeze function
as soon as the temperature in the
freezer is a constant -18 °C or colder.
Metal grille at the back of the
appliance
The metal grille at the back of the
appliance (heat exchanger) should be
dusted at least once a year. A build-up
of dust will increase the energy
consumption of the appliance.
When cleaning the grille, make sure
that the cable, pipework and other
components do not get broken,
kinked or damaged in any way.
35
Problem solving guide
^ Check that the doors have been
closed properly.
Repairs to electrical appliances
should only be carried out by a
suitably qualified and competent
person in strict accordance with
current local and national safety
regulations. Repairs and other work
by unqualified persons could be
dangerous. The manufacturer
cannot be held liable for
^ Has a large amount of fresh food
been frozen at the same time?
This makes the compressor run for
longer, causing the temperature in
the refrigerator to fall automatically.
. . . the compressor is switching in
too frequently and for too long.
unauthorised work.
^ Check whether the ventilation gaps
have been covered over or become
dusty.
What to do if . . .
. . . the appliance does not get cold.
^ Check whether the metal grille (heat
exchanger) at the back of the
appliance has become too dusty.
^ Check whether the appliance has
been switched on. The temperature
display must be lit up.
^ The refrigerator door or the freezer
door has been opened too
frequently, or a large amount of fresh
food has been put in at once for
freezing.
^ Check that the plug is correctly
inserted into the socket and switched
on.
^ Check that the fuse is not defective
and the mains fuse has not tripped. If
it has, there could be a fault with the
household electrical wiring, the
fridge-freezer or another electrical
appliance.
^ Check that the doors have been
closed properly.
. . . the frozen food is thawing
because the freezer section is too
warm.
Contact a qualified electrician or
Miele Service.
^ Is the room temperature lower than
the ambient temperature for which
the appliance is designed?
. . . the temperature in the refrigerator
section or freezer section is too low.
If so, increase the temperature of the
room.
^ Set a warmer temperature.
^ The Super freeze function is still on
and the Super freeze indicator light is
on.
The Super freeze function switches
itself off automatically after approx.
65 hours.
Operating in a room which is too cold
will cause the cooling system to switch
off for too long, causing the freezer to
become too warm.
36
Problem solving guide
. . . food has frozen together.
. . . the Super freeze indicator light
and one of the temperature display
lights are flashing at the same time.
Use a blunt instrument, e.g. a spoon
handle or plastic scraper, to prise it
apart carefully.
There is a fault. Call Miele Service.
. . . the door to the freezer section
will not open because it has been
opened and closed too many times in
succession.
. . . the interior lighting in the
refrigerator is not working.
^ Was the refrigerator section door left
open for too long? The lighting
switches itself off automatically after
approx. 15 minutes if the door is left
open.
This is not a fault. The suction caused
by opening and closing the door
several times in succession is
preventing it from opening. Wait a few
minutes and then try again. It should
now open without force.
If this is not the case, then the interior
lighting is defective.
^ Disconnect the appliance from the
mains.
. . the alarm sounds.
Has one of the the appliance doors
been open for longer than 60 seconds?
^ Close the door.
. . . the alarm sounds and the freezer
section temperature display flashes.
The freezer section temperature has
risen above the set temperature
because
^ Unclip the front cover.
^ the freezer section door has been
opened too frequently, or large
amounts of fresh food have been put
in at once for freezing.
^ the ventilation gaps are blocked.
Once the problem has been resolved
the freezer section temperature display
will light up constantly and the alarm
will go off.
^ Remove the glass panel.
37
Problem solving guide
^ Unscrew the lamp and replace it with
a new one.
Lamp specification:
220 - 240 V, max. 25 W, E 14 cap.
^ Slide the glass panel back in again.
^ Insert the cover and clip it into
position.
. . . the floor of the refrigerator
section is wet.
The condensate drain hole is blocked.
^ Clean the condensate channel and
drain hole.
If you still cannot remedy the fault
having followed these suggestions,
please contact Miele Service.
To prevent unnecessary loss of
temperature it is advisable not to
open the door while waiting for the
appliance to be serviced.
38
Noises
Normal noises
What causes them
Brrrrr...
Humming noise made by the motor (compressor). This noise can
get louder for brief periods when the motor is switching on.
Blubb, blubb....
Click....
A gurgling noise can be heard when coolant is circulating
through the pipes.
Clicking sounds are made when the thermostat switches the
motor on and off.
Sssrrrrr....
Creak ...
On multi-zone and frost-free appliances you can sometimes just
hear the movement of air circulating inside the appliance.
Creaking sounds can be heard when material inside the
appliance expands.
Remember that the noise of the compressor and the coolant circulating in the
system is unavoidable.
Noises that you can
easily rectify
What causes them, and what can you do about
them
Rattling, vibrating
The appliance is uneven: Realign the appliance using a spirit
level, by raising or lowering the screw feet underneath the
appliance.
The appliance is touching another appliance or piece of
furniture: Move it away.
Drawers, baskets or shelves are unstable or sticking: Check
all removable items and refit them correctly.
Are any bottles or containers unstable or knocking against
each other? Separate them.
The transport cable clips are hanging loose at the back of
the appliance: Remove the clips.
39
After Sales / Guarantee
In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
– your Miele Dealer
or
– Miele
(see back cover for contact details).
When contacting your Dealer or Miele,
please quote the model and serial
number of your appliance. This
information is given on the data plate
inside your appliance.
Please note that telephone calls may
be monitored and recorded for
training purposes.
N.B. A call-out charge will be applied
for service visits where the problem
could have been resolved as described
in these instructions.
Guarantee
For information on the appliance
guarantee specific to your country
please contact Miele. See back cover
for contact details.
In the U.K. your appliance is
guaranteed for 2 years from the date of
purchase. However, you must activate
your cover by calling 0845 365 6640 or
40
Electrical connection
Electrical connection U.K.
Non-rewireable plugs (BS 1363)
All electrical work should be carried out The fuse cover must be re-fitted when
by a suitably qualified and competent changing the fuse, and if the fuse cover
person in strict accordance with current is lost, the plug must not be used until a
local and national safety regulations
(BS 7671 in the UK).
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
embossed in words in the base of the
plug (as applicable to the design of the
plug fitted).
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220-240 V 50 Hz supply.
Please ensure that the connection data
quoted on the data plate match the
household mains supply.
Replacement fuses should be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
Connection should be made via a
suitable switched socket which is easily your local electrical supplier.
accessible. For extra safety it is
advisable to protect the appliance with
a suitable residual current device
WARNING
(RCD).
THIS APPLIANCE MUST BE
EARTHED
Do not connect the appliance to the
mains electricity supply by an extension
lead. Extension leads do not guarantee
the required safety of the appliance
(e.g. danger of overheating).
This appliance must not be connected
to the inverter of an autonomous power
supply, e.g. a solar power system.
When switching the appliance on, a
surge in power could trigger the safety
cut-out mechanism. This could damage
the electronic unit.
The appliance must not be used with
so-called energy saving devices. These
reduce the energy supply to the
appliance which could then become
too warm. Using such devices could
alter the specification of the product.
41
Installation
Do not place any appliance which
gives off heat, such as a toaster or
microwave oven, on top of this
appliance, as this would increase
the appliance's energy
Important: tropical / humid
environments
During periods of high humidity,
some condensation may appear on
outside surfaces of cooling
consumption.
appliances. This condensation will
disappear when humidity levels
drop. For prevention, it is advisable
to install the appliance with sufficient
ventilation in a dry and/or an
air-conditioned room.
This appliance must not be installed
directly next to another refrigerator
or freezer.
It does not have side-wall heating,
so installation next to another
refrigerator or freezer could cause a
build-up of condensation between
them.
Please ensure that doors are closing
and sealing properly.
Please ensure that the appliance is
installed in accordance with these
installation instructions and that the
handle is fitted correctly. Should you
require further assistance please
contact your Miele customer service
centre.
Further information is available from
your dealer.
Location
This appliance should be installed in a
dry, well-ventilated room. It should not
be installed where it is exposed to
direct sunlight or directly adjacent to a
heat-producing appliance such as an
oven or a radiator. The room
temperature should not go above or
below the climate range for which the
appliance is designed. The higher the
ambient temperature of the room, the
more energy the appliance requires to
operate.
42
Installation
Climate range
Aligning the appliance
The appliance is designed for use
within certain climate ranges (ambient
temperatures), and should not be used
outside this range. The climate range of
the appliance is stated on the data
plate inside the appliance.
^ To align the appliance, adjust the feet
using the spanner supplied.
Levelling the appliance door
Climate range
Ambient room
temperature
SN
N
ST
T
SN-ST
SN-T
+10°C to +32°C
+16°C to +32°C
+16°C to +38°C
+16°C to +43°C
+10°C to +38°C
+10°C to +43°C
^ Ensure that you unscrew adjusting
foot a from the hinge plate until it sits
on the floor. Then unscrew the foot by
a further 90°.
Operating in a room which is too cold
will cause the cooling system to switch
off for too long, causing the internal
temperature in the appliance to rise
with the risk of frozen food deteriorating
and going off.
Ventilation
Air at the back of the appliance gets
warm. To ensure sufficient ventilation,
the ventilation gaps must not be
covered or blocked in any way. They
should be dusted on a regular basis.
Installation
^ Remove the cable clip from the back
of the appliance.
^ Check that all parts at the back of the
appliance are unhindered. Carefully
remove any hindrance.
^ Carefully push the appliance into
position with the back against the
wall.
43
Installation
Appliance dimensions
A
B
C
KFN 12943 SD edt/cs
2020
750 mm
630 mm
44
Changing the door hinging
The appliance is supplied right-hand
hinged. If left-hand door hinging is
required, follow the instructions below.
To change the door hinging you will
need the following tools:
– a cross-slotted screwdriver,
– a flat-bladed screwdriver,
– a selection of Torx screwdrivers,
– a spanner.
Two people are needed for
changing the door hinging.
Removing the door handles
^ Pull door handle a towards you. Side
section b slides back.
^ Pull side section b firmly back out of
the guides on the mounting plate.
^ Undo the 4 screws (Torx 15) in the
mounting plate, and remove the
handle.
^ Remove the cover caps from the
opposite side, and fit them into the
empty holes.
45
Changing the door hinging
Removing the doors
^ Rotate retaining plate f by 180°.
^ Then fit cover e from the front over
retaining plate f, and slide it over to
the right. The writing must be visible.
Make sure the door shelves are
empty.
^ Close the upper door.
^ Remove cover g, then rotate it by
180° and fit it on the opposite side.
^ Then fit cover e together with
retaining plate f on the opposite
side.
^ Remove cover a by sliding it
forwards from the back and then
lifting it off.
^ Remove cover b by pulling it
upwards.
Caution. The upper door is not
secure as soon as the upper hinge
plate is removed.
^ Loosen screws d in upper hinge
plate c and pull it upwards and off.
^ Carefully lift the upper door off and
place it to one side.
^ Carefully ease off cover e from
above using a screwdriver and then
take it off together with retaining plate
f.
^ Then separate retaining plate f from
cover e, by pushing it slightly to the
left and then pulling the cover
forwards and off.
46
Changing the door hinging
^ Close the lower appliance door.
Caution. The lower door is not
secure as soon as the middle hinge
plate is removed.
^ Remove cap l from the bearing
bush in the door and refit on the
opposite side.
^ Pull the middle hinge pin i upwards
to remove it.
^ Carefully lift the lower door off and
place it to one side.
^ Pull cover j off.
^ Unscrew hinge plate k, turn it
through 180° and fit it on the opposite
side.
^ Pull off plastic cap h, turn it through
180° and fit it back on to hinge plate
k.
^ Using a screwdriver, remove spring
clamp m from underneath the door
and fit it on the opposite side.
^ Refit cover j on the opposite side.
47
Changing the door hinging
Changing over the doors
^ Screw hinge plate f into position on
the opposite side using the two outer
long slots only. To make it possible to
align the door later, do not replace
the centre screw at this stage.
^ Pull hinge pin a together with disc b
and adjustable foot c upwards and
off.
^ Remove cover cap d.
^ Important. Screw the adjustable foot
c into hinge pin a as far as it will go.
^ Undo screws e and take hinge plate
f off.
^ Refit hinge pin a together with disc
b and adjustable foot c. Important.
The notch at the bottom of the hinge
pin should face towards the back.
^ Undo the screw of hinge part h on
hinge plate f slightly. Fit it into the
hole opposite in hinge plate f and
tighten up the screw.
^ Place the door onto hinge pin a.
^ Refit cover cap d in the other hole.
^ Close the lower appliance door.
^ Remove cover g and fit it into the
holes on the opposite side.
48
Changing the door hinging
^ Fit hinge pin i into middle hinge
plate k in the lower door. The ridge
on the hinge pin will fit into the notch
in the hinge plate.
^ Align the door with the appliance
housing using the long slots in the
lower hinge plate. Then tighten the
screws.
^ Then fit the upper door on middle
hinge pin i.
^ Close the upper door.
^ Fit hinge plate c onto the opposite
side and secure it with screws d.
If necessary drill pilot holes for the
screws or use a battery operated
screwdriver.
^ Fit covers a and b to their opposite
sides.
49
Changing the door hinging
Refitting the handles
It is important to check that the side
section of the handle d does not
come into contact with the door seal
when opening the door, as this
would damage the door seal
permanently.
Please make sure you follow the
instructions below carefully when
you refit the handles. The door seal
will be damaged if the handle is
fitted incorrectly.
If, after you have refitted the handle,
you find that the side section does
touch the door seal when the door is
opened:
^ Realign mounting plate c with grub
screws a until the mounting plate
and the side section of the handle d
are at the correct angle and the side
section does not touch the door seal
when the door is opened.
^ Loosely attach the handle to the
opposite side of the door with the two
front screws b.
Mounting plate c must be positioned
on the side of the door so that when the
door is closed it is flush with the side of
the appliance.
If this is not the case,
^ tighten both grub screws a with a
suitable allen key until mounting plate
c lines up correctly.
^ Then tighten all 4 screws b.
^ Slide the side section of the handle
d into the guides on the mounting
plate until it clicks into place.
50
Aligning the appliance doors
The appliance doors can be aligned
with the housing after they have been
fitted.
To align the upper door use the long
outer slots in the middle hinge plate:
In the following illustration the door
is not shown in the closed position to
make it easier to see what you have
to do.
To align the lower door use the long
outer slots in the lower hinge plate:
^ Slightly loosen both screws c.
^ Align the door by sliding the hinge
plate to the left or right.
^ Then tighten screws c.
^ Remove centre screw a from the
hinge plate.
^ Slightly loosen both outer screws b.
^ Align the door by sliding the hinge
plate to the left or right.
^ Then tighten screws b again. Screw
a does not need to be used again.
51
Building in the appliance
The air inlet and outlet must not be
covered or blocked in any way.
They should be dusted on a regular
basis.
When built into a kitchen run (max.
depth 580 mm) the appliance can be
installed directly next to a kitchen
furniture housing unit. The appliance
door will protrude in front of furniture
fronts at the sides by 34 mm and by
55 mm in the middle of the door. This
enables the doors to be opened and
shut without being obstructed.
When installed next to a wall d a
distance of approx. 55 mm must be
maintained on the hinge side between
the wall d and the appliance b, so
that the doors and the handles have
sufficient space for opening.
aTop box
bAppliance
cHousing unit
dWall
The appliance can be installed in a
kitchen run. To match the height of the
rest of the kitchen, the appliance can
be fitted with a suitable top box a.
A ventilation gap of at least 50 mm
depth must be allowed for behind the
appliance across the entire width of the
top box for air to circulate.
The cross section of the air outlet under
the room ceiling must be at least
300 cm2 to ensure that air can circulate
without hindrance. Otherwise the
appliance has to work harder, resulting
in an increase in electricity
consumption.
52
53
54
55
Alteration rights reserved / 0612
KFN 12943 SD edt/cs
M.-Nr. 09 290 880 / 01
|