21A3087
FIRST
CLASS
STAMP
HERE
MODEL 620WE
IN-WALL ENCLOSED LOUDSPEAKER
OWNERS MANUAL
4545 E BASELINE RD
PHOENIX AZ 85040-6400
OTHER HOME AUDIO PRODUCTS FROM MTX
LOUDSPEAKER PLACEMENT
MTX offers a wide assortment of audio components. Ranging from
in-ceiling speakers to amplifiers to accessories. Each component
is value engineered and must meet strict quality control standards
before it becomes part of the MTX product line.
Blueprint Series Loudspeakers are designed to work within any interior
decorating scheme. They can be installed in virtually any location where
flush mounting is possible. To maximize their sound performance however
certain guidelines should be followed. For the best stereo reproduction the
two loudspeakers should be placed an equal distance from your listening
position and separated so that the angle between them, at the listening
position, is between 40 and 60 degrees.
Listed below you will find a sampling of components available
from your authorized MTX dealer.
LPS-600
Speaker/Amplifier Selector
Accommodates up to 6 pair of speakers
Handles up to 250 watts/channel continuous (RMS)
Impedance Protection Circuitry
Accommodates up to 14 gauge wire
MODEL MP42
Multi-Purpose Loudspeaker
Two 4” Woofers, with 1/2” Balanced Dome Tweeter
50 Watts RMS/200 Watts Total Power Handling
Magnetically shielded, weather resistant
Sleek, Euro-style design
For best stereo imaging, we recommend that the units be placed so that
the tweeters are as close as possible to the ear level of a seated listener.
As this is not always possible in keeping with aesthetic design of a
particular room, the Model 620WE loudspeaker is designed with a pivoting
tweeter which rotates to allow you to “aim” the high frequencies toward
the listening position.
Available in white or black
12.6” x 4.8” x 4.9”
PS15
15” Powered Subwoofer System
200 Watt Class D Switching Power Amplifier
Infrared Remote Control for Volume Function
Magnetically Shielded, Downfiring Subwoofer in small enclosure
Signal Sensing Auto Turn On
Red LED Clipping Indicator
Speaker and Line Level Inputs
Continuously variable 50Hz to 150Hz, 24dB/Octave Crossover
Frequency Response 30Hz - 150Hz
17.2” H x 17” W x 20.25” D
Normal Dispersion
Dispersion After Tweeter Adjustment
STEP 1
STEP 4
Using a stud finder (available at low cost at most hardware stores)
or other accurate method, locate center point between two
studs and mark. Using template provided, trace hole pattern on
surface of wall.
Attach loudspeakers wires to speaker terminals, observing correct
polarity (positive to positive and negative to negative). Insert the
speaker into the mounting hole. Be careful not to pinch the
loudspeaker wires in the process. using the integral bubble levels
located on the baffle, align the speaker’s frame either horizontally
or vertically. Once you are satisfied with the speaker’s location,
tighten the eight mounting wings located near each corner of
the frame using a phillips screwdriver. The mounting wings are
designed to swing into position when you start tightening. Note:
the phillips head screws are for tightening the mounting wings.
The torx head screws are for the enclosure which should not be
tightened or loosened.
STEP 2
Using a sabre saw, keyhole saw or very sharp utility knife, cut hole
in wall, following traced pattern.
STEP 5
After speaker panel is secured tightly, test for sound.
STEP 3
STEP 6
Run loudspeaker wires to sound source location. There are several
methods you can use to accomplish wiring, depending on the
construction characteristics of the room or house. You can add a
professional touch to your installation by using a speaker terminal
plate at the source location. Leave sufficient amount of wire at
speaker location (8 to 10 inches) to complete connection.
When you are satisfied the speaker is operational, “aim” the
tweeter, and affix grill. As grill is designed for a snug fit, you’ll need
to position one edge into the slot first, and press or squeeze
around perimeter of thegrill, while pushing the leading edge into
the grill slot.
|