METROLOGIC® INSTRUMENTS, INC.
TECH 7® Laser Bar Code
Projection Scanner
Installation and User’s Guide
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Unpacking List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Scanner Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Configuration to the Host System . . . . . . . . . . . . . . . . . . . . . . . . .3
Stand Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Back Plate Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Parts of Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Visual Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Depth of Scan Field for the MS770 Scanner . . . . . . . . . . . . . . . .12
Depth of Field for the MS775 Scanner . . . . . . . . . . . . . . . . . . . .13
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Applications and Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Appendix A
Specifications
Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Operational . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Appendix B
Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Appendix C
Warranty and Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Appendix D
Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Appendix E
Patents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
ii
Introduction
®
Metrologic's TECH 7 laser bar code projection scanner is encased in
an NEMA-12 steel case. The case construction enables the scanner
to operate in harsh surroundings, especially industrial environments.
Water-resistant, shock-resistant, and rugged, the TECH 7 is also fast,
aggressive and reliable. It can register bar codes at a range of
76mm - 254mm (3" - 10") and can autodiscriminate among all
common codes.
To suit particular applications, two different scan patterns are
available: an omnidirectional pattern of 20 interlocking lines (Model
MS770); or a 12-line raster pattern (Model MS775). The scanner has
a VLD design, a scan speed of up to 2000 lines per second, and uses
less than 8 watts of power.
Other features include an Application Specific Integrated Circuit
©
(ASIC) and MECCA (Metrologic Enhanced Code Correcting
Algorithm). An Application Specific Integrated Circuit (ASIC) is in the
©
decoding system and virtually eliminates misreads. MECCA
(Metrologic Enhanced Code Correcting Algorithm) enables the TECH
7 scanner to read poorly printed, wrinkled or even torn bar codes on
the first pass.
Unpacking List
The shipping carton, should contain the following:
z
z
z
Installation and User's Guide (MLPN: 2159)
ScanSelect™ Scanner Programming Guide (MLPN: 2186)
TECH 7 Model MS770 with omnidirectional scan pattern or
TECH 7 Model MS775 with raster scan pattern
z
Communication Cable with Power Supply (optional) or
Communication Cable (optional)
z
Back Plate (optional) or Stand (optional)
If any item is missing or to order additional items, contact the dealer,
distributor or call Metrologic's Customer Service Department at
1-800-ID-METRO or 1-800-436-3876.
1
Scanner Installation
To maintain compliance with applicable standards, all circuits con-
nected to the scanner must meet the requirements for SELV (Safety
Extra Low Voltage) according to EN 60950. To avoid potential prob-
lems, do not power up the scanner until the communication cable
is secured to the host.
1. "Power off" the host system.
2. Locate the 19-pin female end of the scanner link cable and
find the widest key located above pins L and A. Align this key
with the corresponding key on the scanner box's Mil spec
connector. While pushing in on the connector, rotate the ring
clockwise until it locks into place with a click.
3. Connect the other end of the communication cable to the host
device.
Note: The following statement is applicable if the optional
power adapter available through Metrologic does not power
the bar code scanner and the scanner receives power from a
host device such as a computer system.
Caution: To maintain compliance with standards CSA
C22.2 No. 950/UL 1950 and norm EN 60950, the
power source must meet applicable performance
requirements for a limited power source.
If the scanner is powered by the host, skip to Step 5.
4. Check the AC input requirements of the transformer/power
supply to make sure the voltage matches an available AC
outlet. A socket-outlet must be installed near the
equipment and be easily accessible. Plug the transformer into
the AC outlet to supply power to the scanner.
5. "Power up" the host system.
Note: When the scanner first receives power, the LEDs will
flash and then the scanner will beep once. After the scanner
performs this startup sequence, the green LED will remain on
for a specified time indicating that the laser is on.
2
Configuration to the Host System
The scanner is shipped from the factory programmed to a set of
default conditions noted in the ScanSelect™ Scanner Programming
Guide by an asterisk that appears before the brief definition located
next to the bar code.
In order for the scanner to communicate with a host system properly, it
may need to be programmed. Since each host system is unique, con-
figure the scanner to match the host system requirements. Configure
the scanner by entering the program mode and scanning the appro-
priate bar codes that appear in the ScanSelect Scanner Programming
®
Guide. (To use ScanSet , refer to the ScanSet documentation for
information on how to configure a scanner.)
1. Connect the scanner to the host system (Refer to the Scanner
Connections to the Host section in this guide).
2. Enter program mode by scanning the ENTER/EXIT program
mode bar code. The unit will beep three times
3. Scan the appropriate bar code(s) that appear in the
ScanSelect Scanner Programming Guide. Reveal only one
bar code to the scanner each time. With your hand, cover the
bar code not to be scanned.
4. Exit program mode by scanning the ENTER/EXIT program
mode bar code again. The new options will be saved and the
scanner is ready for normal operation.
3
Stand Installation
With the Metrologic stand (Part #45475), the scanner can be posi-
tioned in one of two directions. The two orientation choices are vertical
or horizontal. (Refer to Figure 1)
Horizontal Mount
Vertical Mount
Figure 1: Stand Orientation
To install this stand, use the four 6-32 x ½ inch machine screws and
two #10 pan head wood screws.
1. Drill two holes into the work
surface that are the same size
and distance as the holes on
1.00 in
the stand base. (Refer to
Figure 2)
3.00 in
1.50 in
2. Use the two #10 pan head
wood screws to attach the
stand to the work surface.
Figure 2: Base of Stand
3. To fasten the scanner:
z
For a horizontal mount,
align the four holes on the
back of the scanner with
the four clearance holes
located on the stand
X
X
Y
Y
X
X
Y
Y
marked with an X in Figure 3.
z
For a vertical mount,
align the four holes on
the back of the scanner
with the four clearance
holes located on the stand
marked with a Y in Figure 3.
X = Holes for Horizontal Mount
Y = Holes for Vertical Mount
Figure 3: Back View of Stand
4. Fasten the scanner to the stand by inserting the four 6-32 x ½
inch screws into the four holes in the scanner's case.
4
Back Plate Installation
With the Metrologic back plate
(Part #45473), position the scanner
in one of two directions. The two
orientation choices are vertical or
horizontal. (Refer to Figure 4). To
use this stand, use the four
Vertical Mount
6-32 x ½ inch machine screws and
four wood screws to attach the unit
to the back plate and work surface.
The maximum distance the screws
should go into the scanner is a ½ inch.
Horizontal Mount
Figure 4: Back Plate Orientation
1. Drill four holes into the work surface that correspond with the
holes indicated by an XY in Figure 5.
2. To fasten the scanner to the back plate:
z
For a horizontal mount, align the four holes on the back of
the scanner with the four clearance holes located on the
back plate marked with an X in Figure 5.
z
For a vertical mount, align the four holes on the back of
the scanner with the four clearance holes located on the
back plate marked with a Y in Figure 5.
3. Fasten the scanner to the back plate by inserting the four
6-32 x ½ inch screws into the four holes in the scanner's case.
Fasten the scanner and back plate to the work surface.
Y
Y
X
Y
Y
X
XY
XY
XY
XY
X
X
X = Scanner Horizontal Mount
Y = Scanner Vertical Mount
XY = Back Plate Mounting
Figure 5: Back Plate Hole Pattern
5
Parts of Scanner
1
2
3
4
Figure 6: Scanner Parts
1
2
Green and Red LEDs
When the green LED is on, this indicates that the unit is
receiving power and the laser is on. When the red LED
flashes on, the scanner has read a bar code successfully.
When the red light turns off, communication to the host is
complete.
Speaker
The speaker emits a beep when a bar code has been
decoded.
3
4
Laser Output Window
This aperture emits the laser light.
Mil spec Connector
The 19-pin male Mil spec connector was designed to connect
a communication cable from the scanner to a host device.
The communication cable may include a power supply or it
may be designed to draw power directly from the host device.
The standard TECH 7 has one connector. (When the atrium
option is installed, a second connector is installed on the unit
to connect the MX001 Industrial Control Interface box.)
6
Visual Indicators
There is a red and green LED at the top of the scanner. When the
scanner is on, the flashing or stationary activity of the LEDs indicates
the status of the scan and scanner.
Steady Green
When the laser is on, the green LED is also on. This
occurs when an object is in the scan field.
Steady Green; Red Flash
When the scanner successfully reads a bar code, the red
LED will flash then beep once. If the red LED does not
flash or the scanner does not beep once, then the bar
code has not been successfully read.
Steady Red and Green
After a successful scan, the scanner transmits the data to
the host device. When the host is not ready to accept the
information, the scanner's red LED will remain on until the
data can be transmitted.
Alternating Red and Green
This indicates the scanner is in program mode.
Steady Red
This indicates the scanner is in ScanSet mode.
No Red or Green LED
There are two reasons why the LEDs will not be illumi-
nated. First, if the scanner is receiving power and the
LEDs are not on, then the scanner has remained dormant
for a specified time and the laser has turned off. To reacti-
vate the unit, touch the touch plate. Secondly, if the
scanner is not receiving power from the host or trans-
former, then the LEDs will not turn on.
Flashing Red
This indicates the scanner has experienced a laser sub-
system failure. Return the unit for repair at an authorized
service center.
7
Signaux Optiques
Sur la partie supérieure du scanner se trouvent une diode LED rouge
et une diode LED verte. Quand le scanner est sous tension, les
diodes rouge et verte clignotantes ou allumées vous informent sur
l'état du scanner.
Ni la diode rouge, ni la diode verte n'est allumée
Il existe deux raisons possibles pour que les diodes ne s'allument pas.
Premièrement: si le scanner reçoit de l'énergie sans que les diodes ne
s'allument, le scanner est resté sans servir pendant une certaine
période et le laser est désactivé. Pour le réactiver, passer un objet
devant le palpeur infrarouge. Deuxièmement: quand le scanner ne
reçoit de l'énergie ni de l'ordinateur central, ni du transformateur, les
diodes restent éteintes.
La diode verte reste allumée
Quand le laser est en service, la diode verte s'allume également.
C'est le cas quand un objet se trouve devant le palpeur. La diode
verte reste allumée tant que la temporisation de l'infrarouge dure ou
jusqu'à ce que le scanner soit désactivé.
La diode verte reste allumée; la diode rouge clignote
Après lecture avec succès d'un code à barres par le scanner, la diode
rouge se met à clignoter, suivie d'un bip sonore unique. Si la diode
rouge ne clignote pas ou quand aucun bip sonore n'est émis, cela sig-
nifie que le code à barres n'a pas pu être lu avec succès.
Les diodes rouges et vertes restent allumées
Une fois la lecture effectuée avec succès, le scanner transmet les
données à l'ordinateur central. Si ce dernier n'est pas prêt à recevoir
les données, la diode rouge du scanner reste allumée jusqu'à ce que
les données puissent être transmises.
Les diodes rouges et vertes clignotent en alternance
Indique que le scanner se trouve en mode de programmation.
La diode rouge reste allumée
Indique que le scanner se trouve en mode ScanSet.
Diode rouge clignotante
Indique une panne de laser pendant la lecture. Veuillez envoyer votre
appareil chez unconcessionnaire pour réparation.
8
Optische Anzeigen
Auf dem Scanner befinden sich eine rote und eine grüne Leuchtdiode. Bei
eingeschaltetem Scanner geben Ihnen die blinkenden bzw. feststehenden
Leuchtdiodenanzeigen Aufschluß über den Abtast-und Scannerstatus.
Weder rote noch grüne Leuchtdiodenanzeige
Es gibt zwei mögliche Gründe, weshalb die Leuchtdiodenanzeigen nicht
aufleuchten. Erstens: Wenn der Scanner mit Energie versorgt wird und die
Leuchtdiodenanzeigen nicht aufleuchten, so ist der Scanner für einen bes-
timmten Zeitraum untätig geblieben, und der Laser ist abgeschaltet. Zur
Reaktivierung der Einheit sollten Sie ein Objekt vor dem Infrarot-Sensor
hin- und herbewegen. Zweitens: Wenn der Scanner weder vom
Hostrechner noch vom Transformator Energie erhält, so leuchten die
Leuchtdiodenanzeigen nicht auf.
Feststehende grüne Anzeige
Wenn der Laser in Betrieb ist, leuchtet die grüne Leuchtdiodenanzeige
ebenfalls auf. Dies ist dann der Fall, wenn sich ein Objekt im Abtastfeld
befindet. Die grüne Leuchtdiodenanzeige leuchtet solange auf, bis das
Infrarot-Timeout abgelaufen ist, oder bis der Scanner abgeschaltet wird.
Feststehende grüne Leuchtanzeige; rote Blinkanzeige
Nach erfolgreichem Lesen eines Barcodes durch den Scanner blinkt
die rote Leuchtdiodenanzeige auf, gefolgt von einem einmaligen Piep-
Signal. Blinkt die rote Leuchtdiodenanzeige nicht auf oder sendet der
Scanner kein Piep-Signal aus, so konnte der Barcode nicht erfolgreich
gelesen werden.
Feststehende rote und grüne Leuchtanzeige
Nach erfolgreichem Abtasten überträgt der Scanner die Daten an das
Hostgerät. Falls das Hostgerät zur Datenannahme nicht bereit ist, leuchtet
die rote Leuchtdiodenanzeige des Scanners solange auf, bis die Daten
übertragen werden können.
Alternierende rote und grüne Leuchtanzeige
Zeigt an, daß sich der Scanner im Programmiermodus befindet.
Feststehende rote Leuchtanzeige
Zeigt an, daß sich der Scanner im ScanSet-Modus befindet.
Aufblinkende rote Leuchtanzeige
Zeigt an, daß beim Scanner ein Laserausfall vorliegt. Bringen Sie das
Gerät zur Reparatur in ein Vertragsservicecenter.
9
Segnali Ottici
Sullo scanner si trovano due diodi luminosi: uno rosso e uno verde.
Quando lo scanner è inserito, i diodi luminosi, che possono o essere
accesi in continuazione o lampeggiare, Vi informano sullo stato della
scansione e dell'apparecchio.
Né il diodo luminoso rosso né quello verde sono accesi
Vi sono due possibili cause se i diodi luminosi non sono accesi. Prima
causa: se lo scanner viene alimentato e i diodi luminosi non sono
accesi, lo scanner è rimasto disattivato per un determinato periodo e il
laser è spento. Per riattivare l'unità dovreste muovere un oggetto
davanti al sensore a infrarossi. Seconda causa: se lo scanner non
viene alimentato né dal calcolatore host né dal trasformatore, i due
diodi luminosi non sono accesi.
Il diodo luminoso verde è acceso
Quando il laser è inserito, è acceso anche il diodo luminoso verde.
Questo si ha quando un oggetto si trova nella zona di scansione. Il
diodo luminoso verde è acceso fino al raggiungimento del timeout
infrarossi oppure fino allo spegnimento dello scanner.
Il diodo luminoso verde è acceso; quello rosso lampeggia
Dopo la lettura riuscita di un codice a barre da parte dello scanner il
diodo luminoso rosso lampeggia e quindi viene emesso un unico seg-
nale beep. Se il diodo luminoso rosso non lampeggia oppure lo
scanner non emette un segnale beep, ciò significa che la lettura del
codice a barre non è riuscita.
Sono accesi sia il diodo luminoso rosso che quello verde
Dopo la scansione riuscita lo scanner trasmette i dati all'host. Se l'host
non è pronto per accettare i dati, il diodo luminoso rosso dello scanner
è acceso fino a che i dati possono essere trasmessi.
Il diodo luminoso rosso e quello verde sono accesi in alternanza
Ciò indica che lo scanner si trova nella modalità di programmazione.
Il diodo luminoso rosso è acceso
Ciò indica che lo scanner si trova nella modalità ScanSet.
Il diodo luminoso rosso lampeggia
Ciò indica che lo scanner ha un guasto a livello del laser. Fate riparare
l'apparecchio da un centro di assistenza autorizzato.
10
Labels
There is one label located inside the window of the scanner noting
that this device is a CDRH Class IIa laser product and IEC 825
LASERKLASSE 1. Also, on the scanner is a label located on the back
of the unit. This label contains information such as the model number,
date of manufacture, serial number, and approvals. The following are
samples of the labels located on the unit.
®
Metrologic
This product complies with US
Metrologic Instruments, Inc.
Blackwood, New Jersey, USA
Contains no user serviceable
components.
DHHS Standard 21 CFR Chapter 1
Subchapter J. Class IIa Laser
Product. Avoid long-term viewing
of direct laser light.
Warranty void if case is
opened.
Complies with FCC Class A.
See manual.
Eviter toute exposition prolongee
de la vue au rayonnement laser
direct. Appareil laser Classe IIa
Manufactured Blackwood, NJ.
11-30V
August 1999
Model: IS770-F1
TECH 7™ Barcode Scanner
Serial # : XXXXXXXXXX
CAUTION:
Patents #5,081,342; #5,216,232; #1,268,257
Worldwide Patents Pending
Laser Light when opened.
DO NOT STARE INTO BEAM
11
Depth of Scan Field for the MS770 Scanner
The depth of field for the scanner is 76mm to 254mm (3.00” - 10.00”)
from the laser output window. Pass the symbol through the scan area
in order for the scanner to recognize the bar code. (Refer to Figure 7)
76 mm [3.00 in]
254 mm [10.00 in]
152 mm [6.00 in]
Figure 7: MS770 Scanner, Front View
12
Depth of Scan Field for the MS775 Scanner
The depth of field for the scanner is 76mm to 254mm (3.00” - 10.00”)
from the laser output window. Pass the symbol through the scan area
in order for the scanner to recognize the bar code. (Refer to Figure 8)
76 mm [3.00 in]
254 mm [10.00 in]
229 mm [9.00 in]
Figure 8: MS775 Scanner, Front View
13
Maintenance
Smudges and dirt can interfere with the proper scanning of a bar
code. Therefore, the output window will need occasional cleaning.
1. Spray glass cleaner onto lint free, nonabrasive cleaning cloth.
2. Gently wipe the output window.
Applications and Protocols
The model number on each scanner includes the scanner number and
communications protocol.
Version Identifier
Communication Protocol(s)
1
15
RS-232, OCIA, Bidirectional RS-232
Light Pen Emulation
14
Appendix A
Specifications
Application:
Light Source:
CDRH:
Industrial Projection Scanner
Visible Laser Diode 650 ± 5 nm or 670 ± 5 nm
CLASS IIa laser product
Certifications:
CE, UL listed for the US and CUL for
Canada
EMC:
EMI:
EN 60825: Class 1
FCC, ICES-003 & EN 55022 Class A
Mechanical
Dimensions:
184 mm(L) x 186 mm (W) x 78 mm (D)
[7.25 in (L) x 7.3 in (W) x 3.06 in (D)]
Weight:
2.35 kg. (5.19 lbs.) without cable
May be used in any orientation
Back plate mount or Vertical stand
NEMA-12 steel case
Orientation:
Mounting:
Top Cover:
Host Cable Length:
nector
1.83 m (6 Ft.) cable with mil spec con-
Electrical
Power Consumption:
Input Voltage:
8 watts, host system or wall transformer
11-30 VDC
Operating Current:
Standby Current:
DC Transformers:
420 mA typical @ 20V
210 mA typical @ 20V
120V (AC in), 230V (AC in), 240V
( AC in); output 20V @ 750 mA
Specifications subject to change without notice
15
Appendix A (Continued)
Operational
Depth of Scan Field:
Scan Speed:
76mm to 254 mm (3 in to 10 in)
Model 770: 2000 scan lines per second
Model 775: 1200 scan lines per second
Scan Pattern:
Model 770: Omnidirectional
(20 interlocking lines)
Model 775: 12-line raster
Indicators:
LED: green = laser on; red = good read
Selection of 3 tones for "Good Read"
Clean window periodically
Beeper Operation:
Maintenance Required:
Decode Capability:
System Interfaces:
Optional:
Autodiscriminates
RS232C; Light Pen Emulation; OCIA
Opto coupled 6 amps US and Canada,
5 amps
EEA countries TRIAC output; object
sensor input
Print Contrast:
35% minimum reflectance difference
360°, 60°, 60°
Roll, Pitch, Yaw:
Environmental
Storage Temperature:
Operating Temperature:
Humidity:
-40°C to 60°C (-40°F to 140°F)
0°C to 35°C (32°F to 95°F)
5% to 95% relative humidity,
non-condensing
Light Levels:
Up to 3200 foot candles - works in direct
sun
Ventilation:
Shock:
None required
100g for 1ms
8 kV IEC 801-2
ESD:
Contaminants:
Protects against dust, falling dirt, and
dripping non-corrosive liquid
Specifications subject to change without notice.
16
Appendix B
Pin Assignments
Version "1" Pin Assignments for RS-232, OCIA, and Bi-direc-
tional RS-232
Each TECH 7 scanner has a 19-pin male Mil spec connector that is
located on the side of the unit. To connect the scanner to the host
device, use a communication cable with a female Mil spec connector.
The communication cable may include a power supply or it may be
designed to draw power directly from the host device. This item can
be ordered when the scanner is purchased.
The Version "1" scanner is designed to be used for RS-232, OCIA,
and RS-232 with limited receiving capabilities.
The following is a list of pin assignments. The pin numbers are
impressed on the male Mil spec connector. For easier reference, refer
to Figure 9 for pin locations.
Pin
Function
A
B
C
D
E
F
G
H
J
R Data
RTS Output
A
L
K
M
N
B
Signal Ground
CTS Input
R Data Return
RS-232 Output
Clock in
J
P
E
U
F
T
C
H
R
S
D
G
Clock in Return
Clock Out
K
L
Shield Ground
DTR Input
Figure 9: Pin Locations
M
N
P
R
S
Clock Out Return
Power to Scanner & 24 VDC
Earth Ground
Power Ground
RS-232 Input
17
Appendix B (Continued)
Version "15" Pin Assignments for Light Pen Emulation
Each TECH 7 scanner has a 19-pin male Mil spec connector that is
located on the side of the unit. To connect the scanner to the host
device, use a communication cable with a female Mil spec connector.
The communication cable may include a power supply or it may be
designed to draw power directly from the host device. This item can
be ordered when the scanner is purchased.
The Version "15" scanner is designed to be used for Light Pen
Emulation communication.
The following is a list of pin assignments. The pin numbers are
impressed on the male Mil spec connector. For easier reference, refer
to Figure 10 for pin locations.
Pin
Function
A
B
C
D
E
F
G
H
J
R Data
Light Pen Data Output
Signal Ground
Light Pen Source & 5 VDC
R Data Return
RS-232 Output
Clock in
A
L
K
M
N
B
J
P
E
U
F
T
C
H
R
S
D
G
Clock in Return
Clock Out
K
L
Shield Ground
DTR Input
Clock Out Return
Power to Scanner & 24 VDC
Earth Ground
Figure 10: Pin Locations
M
N
P
R
S
Power Ground
RS-232 Input
18
Appendix C
Warranty and Disclaimer
Limited Warranty
The Tech 7 scanners are manufactured by Metrologic at its Blackwood, New Jersey,
U.S.A. facility. The Tech 7 scanners have a two (2) year limited warranty from the date
of manufacture. Metrologic warrants and represents that all Tech 7 scanners are free of
all defects in material, workmanship and design, and have been produced and labeled
in compliance with all applicable U.S. Federal, state and local laws, regulations and
ordinances pertaining to their production and labeling.
This warranty is limited to repair, replacement of Product or refund of Product price at
the sole discretion of Metrologic. Faulty equipment must be returned to the Metrologic
facility in Blackwood, New Jersey, U.S.A. or Puchheim, Germany. To do this, contact
Metrologic's Customer Service/Repair Department to obtain a Returned Material
Authorization (RMA) number.
In the event that it is determined the equipment failure is covered under this warranty,
Metrologic shall, at its sole option, repair the Product or replace the Product with a
functionally equivalent unit and return such repaired or replaced Product without
charge for service or return freight, whether distributor, dealer/reseller, or retail con-
sumer, or refund an amount equal to the original purchase price.
This limited warranty does not extend to any Product which, in the sole judgement of
Metrologic, has been subjected to abuse, misuse, neglect, improper installation, or
accident, nor any damage due to use or misuse produced from integration of the
Product into any mechanical, electrical or computer system. The warranty is void if the
case of Product is opened by anyone other than Metrologic's repair department or
authorized repair centers.
THIS LIMITED WARRANTY, EXCEPT AS TO TITLE, IS IN LIEU OF ALL OTHER WARRANTIES
OR GUARANTEES, EITHER EXPRESS OR IMPLIED, AND SPECIFICALLY EXCLUDES,
WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTIC-
ULAR PURPOSE UNDER THE UNIFORM COMMERCIAL CODE, OR ARISING OUT OF CUSTOM
OR CONDUCT. THE RIGHTS AND REMEDIES PROVIDED HEREIN ARE EXCLUSIVE AND IN
LIEU OF ANY OTHER RIGHTS OR REMEDIES. IN NO EVENT SHALL METROLOGIC BE
LIABLE FOR ANY INDIRECT OR CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAM-
AGES TO PERSON OR PROPERTY, OR EFFECT ON BUSINESS OR PROPERTY, OR OTHER
DAMAGES OR EXPENSES DUE DIRECTLY OR INDIRECTLY TO THE PRODUCT, EXCEPT AS
STATED IN THIS WARRANTY. IN NO EVENT SHALL ANY LIABILITY OF METROLOGIC
EXCEED THE ACTUAL AMOUNT PAID TO METROLOGIC FOR THE PRODUCT.
METROLOGIC RESERVES THE RIGHT TO MAKE ANY CHANGES TO THE PRODUCT
DESCRIBED HEREIN.
USA Corporate Headquarters
90 Coles Road
Blackwood, NJ 08012-4683
Customer Service: 1-800-ID-METRO
Tel: 856-228-8100
South America
Rua Flórida 1.821, 5° Andar-Brooklin
CEP 04571-090, São Paulo-SP, Brasil
Outside Brazil: Metrologic South America
Tel: 55-11-5505-6568
Fax: 856-228-6673
Fax: 55-11-5505-1681
Inside Brazil: Metrologic do Brasil Ltda
Tel: 55-11-5505-2396
Europe
Metrologic Instruments GmbH
Dornierstrasse 2
Fax: 55-11-5507-2301
82178 Puchheim b.
Munich, Germany
Tel: 49-89-89019-0
Fax: 49-89-89019-200
Asia
Metrologic Asia (PTE) Ltd.
31, Kaki Bukit Road 3
#05-08 Techlink
Singapore 417818
Tel:65-842-7155
Fax: 65-842-7166
19
Appendix D
Notices
This equipment has been tested and found to comply with limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference, in which case the user will
be required to correct the interference at his own expense. Any unauthorized changes or modifica-
tions to this equipment could void the users authority to operate this device.
Notice
This Class A digital apparatus complies with Canadian ICES-003.
Caution
Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous laser light. Under no circumstances should the customer attempt to service the
laser scanner. Never attempt to look at the laser beam, even if the scanner appears to be nonfunc-
tional. Never open the scanner in an attempt to look into the device. Doing so could result in haz-
ardous laser light exposure. The use of optical instruments with the laser equipment will increase
eye hazard.
Remarque
Cet appareil numérique de la classe A est conformé a la norme NMB-003 du Canada.
Attention
L'emploi de commandes, réglages ou procédés autres que ceux décrits ici peut entraîner de graves
irradiations. Le client ne doit en aucun cas essayer d'entretenir lui-même le scanner ou le laser. Ne
regardez jamais directement le rayon laser, même si vous croyez que le scanner est inactif.
N'ouvrez jamais le scanner pour regarder dans l'appareil. Ce faisant, vous vous exposez à une ray-
onnement laser mortel. L'emploi d'appareils optiques avec cet équipement laser a-ugmente le risque
d'endommagement de la vision.
Achtung
Die Verwendung anderer als der hierin beschriebenen Steuerungen, Einstellungen oder Verfahren
kann eine lebensgefährliche Laserstrahlung hervorrufen. Der Kunde sollte unter keinen Umständen
versuchen, den Laser-Scanner selbst zu warten. Sehen Sie niemals in den Laserstrahl, selbst wenn
Sie glauben, daß der Scanner nicht aktiv ist. Öffnen Sie niemals den Scanner, um in das Gerät
hineinzusehen. Wenn Sie dies tun, können Sie sich einer lebensgefährlichen Laserstrahlung aus-
setzen. Der Einsatz optischer Geräte mit dieser Laserausrüstung erhöht das Risiko einer
Sehschädigung.
Attenzione
L’utilizzo di sistemi di controllo, di regolazioni o di procedimenti diversi da quelli decritti nel presente
Manuale può provocare dei raggi laser pericolosi per la vita. Il cliente non deve assolutamente
tentare di riparare egli stesso lo scanner laser. Non guardate mai nel raggio laser, anche se credete
che lo scanner non sia attivo. Non aprite mai lo scanner per guardare d-entro l’apparecchio. Se tut-
tavia lo fate, potete esporVi a dei raggi laser pericolosi per la vita. L’uso di apparecchi ottici con
questo equipaggiamento laser aumenta il rischio di danni alla vista
20
Appendix D (Continued)
European Standard
Warning
This is a class A product. In a domestic environment this product
may cause radio interference in which case the user may be required
to take adequate measures.
Funkstöreigenschaften nach EN 55022:1998
Warnung!
Dies ist eine Einrichtung der Klasse A. Diese Einrichtung kann im
Wohnbereich Funkstörungen verursachen; in diesem fall kann vom
Betrieber verlangt werden, angemessene Maßnahmen durchführen.
Standard Europeo
Attention
Ce produit est de classe "A". Dans un environnement domestique,
ce produit peut être la cause d'interférences radio. Dans ce cas l'u-
tiliseteur peut être amené à predre les mesures adéquates.
Attenzione
Questo e' un prodotto di classe A. Se usato in vicinanza di residenze
private potrebbe causare interferenze radio che potrebbero
richiedere all'utilizzatore opportune misure.
21
Appendix E
Patents
“Patent Information
This METROLOGIC product may be covered by one or more of the
following U.S. Patents:
U.S. Patent No. 4,360,798; 4,369,361; 4,387,297; 4,460,120;
4,496,831; 4,593,186; 4,607,156; 4,673,805; 4,736,095; 4,758,717;
4,816,660; 4,845,350; 4,896,026; 4,923,281; 4,933,538; 4,960,985;
4,992,717; 5,015,833; 5,017,765; 5,059,779; 5,081,342; 5,117,098;
5,124,539; 5,130,520; 5,132,525; 5,140,144; 5,149,950; 5,180,904;
5,200,599; 5,216,232; 5,229,591; 5,247,162; 5,250,790; 5,250,791;
5,250,792; 5,260,553; 5,262,628; 5,280,162; 5,280,164; 5,304,788;
5,321,246; 5,324,924; 5,396,053; 5,396,055; 5,408,081; 5,410,139;
5,436,440; 5,449,891; 5,468,949; 5,479,000; 5,532,469; 5,545,889
5,557,093; 5,627,359; 5,637,852; 5,777,315; 5,789,731;
No license right or sublicense is granted, either expressly or by impli-
cation, estoppel, or otherwise, under any METROLOGIC or third party
intellectual property rights (whether or not such third party rights are
licensed to METROLOGIC), including any third party patent listed
above, except for an implied license only for the normal intended use
of the specific equipment, circuits, and devices represented by or con-
tained in the METROLOGIC products that are physically transferred to
the user, and only to the extent of METROLOGIC’s license rights and
subject to any conditions, covenants and restrictions therein.”
Other worldwide patents pending.
22
Index
A
L
AC 2
Labels 11
Applications 1, 14, 15
ASIC 1
LED
green 2, 6, 7, 8, 9, 10
Atrium option 6
Autodiscriminate 1, 16
red 2, 6, 7, 8, 9, 10
Light Pen Emulation 14, 16, 18
B
M
Back Plate 1, 5, 15
Maintenance 14, 16
Bidirectional RS-232 14, 17
MECCA 1
Mounting 4, 5
MS770 1, 12, 16
MS775 1, 13, 16
MX001 6
C
Cable 2, 6, 17, 18
communication 1, 6
scanner link 2
N
Caution 2, 21
Compliance 2, 11, 15
Configure 3
NEMA-12 1, 15
Notices 20
Connector 2, 6
mil spec 2, 6, 17, 18
Current 15
O
OCIA 14, 16, 17
Customer Service iii, 1, 19
Orientation 4, 5, 15
D
DC 15
P
Patents 22
Depth of Scan Field 12, 13
Dimensions 15
Disclaimer 19
Pin Assignments 17, 18
Pins 2
Power 1, 2, 7, 15
Power adapter 2
Program 3, 7
Protocols 14
H
Host Device 2, 3, 6, 15
I
R
Install 2, 4, 5
back plate 5
scanner 2
stand 4
Repair 7, 19
Requirements 2, 3
RMA 19
RS-232 14, 16, 17
Interfaces 16
23
Index
S
Scan pattern 1, 16
Scan Speed 16
ScanSelect 3
ScanSet® 3
Service Center 7
Specifications 15
Stand 1, 4, 15
V
Visual Indicators 7, 8, 9, 16
Voltage 15
W
Warning 21
Warranty 19
Window 6, 11, 14
24
March 2006
Printed in the USA
|