INSTALLATION INSTRUCTIONS FOR PART 99-8220
APPLICATIONS
Toyota
Tundra 2007-2011
Sequoia 2008-2011
99-8220
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
• 99-8220 - Scratch Resistant Matte Black
• 99-8220HG - High Gloss Black
• 99-8220CHG - High Gloss Charcoal (matches 2010-UP models)
KIT COMPONENTS
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
• E) Double DIN Trim Plate • F) Pocket
C
D
A
E
B
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Wire harness:
• 70-1761 Toyota 87-up
• TYTO-01 Toyota amp interface harness 03-up
Antenna adapter:
F
• Not required
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver • Socket Set
1-800-221-0932
© COPYRIGHT 2007-2010 METRA ELECTRONICS CORPORATION
99-8220 DASH DISASSEMBLY
TOYOTA TUNDRA (Console Shift) 2007-2011
TOYOTA SEQUOIA 2008-2011
A
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
2
3
Unclip and remove the top trim panel
around cup holders. (Figure A)
Remove (1) Phillips screw from shifter
trim panel and remove panel.
(Figure B)
4
Unclip, unplug and remove the cli-
mate control assembly. (Figure C)
B
Continue dash disassembly.
C
1
99-8220 DASH DISASSEMBLY
TOYOTA TUNDRA (Console Shift) 2007-2011
TOYOTA SEQUOIA 2008-2011
5
6
Remove (4) 10 MM bolts securing the
radio. (Figure D)
Unclip the right side of the instrument
panel trim and pull back the trim,then
unclip,unplug and remove radio.
(Figure E)
Continue to kit assembly.
2
99-8220 DASH DISASSEMBLY
TOYOTA TUNDRA (Column Shift) 2007-2011
TOYOTA SEQUOIA 2008-2011
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
2
A
Remove (2) plastic Phillips screws
one from each side of the trim panel
below the cup holder then unclip and
remove the panel. (Figure A)
3
4
Pull the cup holder out and depress
the (2) clips on each side to slide cup
holder out of cup holder panel.
(Figure B)
Remove (4) Phillips screws from cup
holder panel assembly then unclip
and remove assembly. (Figure C)
B
5
6
Unclip and remove the climate control
assembly. (Figure D)
Remove (4) 10 MM bolts securing the
radio.
7
Unclip the right side of the instrument
panel trim and pull back then unclip
and remove radio.
Continue to kit assembly.
C
D
3
99-8220 KIT ASSEMBLY
DIN MOUNT RADIO PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
A
Slide the DIN cage into the radio hous-
ing and secure by bending the metal
locking tabs outward. (Figure A)
1
2
3
Slide the aftermarket radio into the cage
until it snaps into place. (Figure B)
Snap the pocket into the radio housing.
(Figure C)
Continue to final assembly.
B
C
4
99-8220 KIT ASSEMBLY
ISO MOUNT RADIO PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
Mount the ISO Brackets to the radio
1
using the screws supplied with the
radio. (Figure A)
2
3
4
Slide the radio into the radio housing
until it snaps into place. (Figure B)
Snap the trim plate onto the front of
the Radio/Housing assembly. (Figure C)
Snap the Pocket into the radio
housing. (Figure D)
Continue to final assembly.
5
99-8220 KIT ASSEMBLY
DOUBLE DIN RADIO PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
1
2
Cut and remove the center bar from
the radio housing. (Figure A)
Snap the Double DIN brackets to the
inside edge of the radio housing.
(Figure B)
3
4
Slide the Double DIN radio into the
bracket/radio housing assembly and
secure the radio to the assembly using
the screws supplied with the radio.
(Figure C)
Snap the Double DIN trim plate onto
the front of the radio/housing assem-
bly. (Figure C)
Continue to final assembly.
6
99-8220 KIT ASSEMBLY
STACKED ISO MOUNT UNITS PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
1
2
Cut and remove the center bar from
the radio housing. (Figure A)
Snap the Double DIN brackets to the
inside edge of the radio housing.
(Figure B)
3
4
Slide the stacked ISO mount units into
the bracket/housing assembly and
secure the units to the assembly using
the screws supplied with the units.
(Figure C)
Snap the Double DIN trim plate onto
the front of the radio/housing assem-
bly. (Figure C)
Continue to final assembly.
7
99-8220 FINAL ASSEMBLY
FINAL ASSEMBLY
A
B
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
Right Front (+) . . . . . . . . . . . . Gray
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
8
99-8220
NOTES
9
99-8220 INSTRUCTIONS
1-800-221-0932
REV. 11/22/10 © COPYRIGHT 2007-2010 METRA ELECTRONICS CORPORATION INST99-8220
|