Master Appliance Blowtorch MT 5 User Manual

 
MICROTORCH MT-5  
BOTTOM VIEW  
CAP  
Fig. 4  
WINDSHIELD  
OFF-LOCK  
MORE  
GAS  
LESS  
GAS  
IGNITION BUTTON  
SAFETY LOCKOUT  
LEVER  
Fig. 1  
Fig. 2  
Fig. 3  
GAS FLOW VALVE STEM  
FLAME ADJUSTMENT  
To extinguish flame / Turn off gas flow  
From Normal Use: Release pressure from ignition button. Unit will shut  
off immediately. (figure 2)  
From Hands free use: Slide hands free slide stem to full left position.  
Unit will shut off immediately (figure 3).  
Specifications  
BODY  
Size dim.  
Unit Weight  
75x32x21mm  
45g  
CAUTION:  
1. Keep out of reach of children.  
2. Do not touch flame guard when hot!  
3. Butane gas is extremely flammable, please handle with care.  
4. Always point away from eyes and body when igniting  
or operating.  
5. Do not store under direct sunlight or anywhere that will exceed  
104°F/40°C.  
Internal tank pressure 65 g/mm2 max  
Continuous burn time 20 min. - one fill  
FUEL VIEW  
FUEL ADJUSTMENT  
Please read and understand  
all warnings and instructions.  
6. Under no circumstances should you attempt to repair a damaged torch.  
7. After using, let the tool cool down before storing.  
To ignite unit (figure 2)  
• Remove safety cap.  
Contains flammable gas under pressure. Do not use near sparks or open  
flame. Do not puncture or incinerate container.  
• Slide lockout lever to off position and hold in position while slowly  
depressing ignition button.  
• After a few attempts if no flame appears, fine tune the unit’s gas flow  
and retry ignition step above.  
To refuel unit. (figure 1)  
• Make sure the unit is OFF and COOL to touch.  
• Make sure the protective cap is on nozzle.  
• Use only Master Ultratane® butane to refuel unit, hold unit firmly with  
filler valve pointing up. Place nozzle of butane canister down onto refill  
valve and press butane canister down and up in short duration until fuel  
tank is filled. Allow 2 -3 minutes for gas to stabilize after filling unit.  
• Flame is invisible in direct sunlight. Use caution.  
• Point away from face and body when igniting.  
• Use in well ventilated areas.  
• Always have a fire extinguisher/ bucket of water nearby work area.  
• The tank contents are visible through the clear viewing port on the unit.  
To adjust fuel flow (figure 4)  
• Adjust the unit fuel flow by turning the black fuel flow adjustment wheel  
at bottom of unit. A 1/4 inch turn CW/CCW will usually be all that is  
needed. Note: Extreme caution must be taken not to over adjust fuel  
flow. If you are unable to make proper adjustment, please call customer  
service. As the gas is consumed, the gas flow can be adjusted periodi-  
cally to ensure proper flame height. It is recommended that the user set  
the flame height to 1/2 inch to 1 inch. If the flame height is set outside  
these limits the fuel flow / flame may become unstable and cause  
premature clogging or ignition failure.  
Hands free mode (figure 3)  
2420-18th Street, Racine, WI 53403 U.S.A.  
PHONE: 262-633-7791 FAX: 262-633-9745  
To engage hands free mode follow ignition steps above and once the  
unit is ignited, position slide stem button (found on backside of unit) to  
full right position. This will allow hands free operation of unit.  
Designers and Manufacturers of Heat Tools  
 

La Crosse Technology Clock WT 2150A User Manual
Learning Resources Baby Toy LER1811 User Manual
Lenoxx Electronics Home Theater System HT3917 User Manual
Lexmark Printer 032 User Manual
LG Electronics Computer Monitor 57M User Manual
Linksys Network Card WCF54G User Manual
Makita Cordless Saw LC1230 User Manual
Makita Impact Driver BTW200 User Manual
MartinLogan Speaker CLX User Manual
Metabo Grinder WF 18 LTX 125 User Manual