CORDLESS RECIPRO SAW Model 4390D (MCP)
Model 4390DW(MCP)
Item
No.
Part
No.
No.
Used
Item
No.
Part
No.
No.
Used
Description
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1
1
1
3
1
1
1
1
1
1
1
1
1
1
Motor D.C. 9.6V (With Item 16)
Supporter Com.
Gear Com.
Thin Washer 4
Flat Washer 4
Needle Bearing 407
Slider Com.
Plane Bearing 3
Felt
15
16
17
18
19
20
21
22
23
24
1
1
1
1
1
1
1
1
1
1
1
1
8
1
Housing (L)
*
*
152272-4
Spur Gear 15
Compression Spring 3
Lock-Off Lever
Battery Holder 20
Trigger
Switch (Old 651866-7)
Roller
Pin 4
Shoe
Housing (R)
Stop Ring E-3
*
231390-2
*
253307-5
414169-8
643909-9
410972-5
651899-2
322099-8
256654-3
253874-0
212014-9
*
214020-0
*
Blade Set
*
*
214020-0
Plane Bearing 3
Plane Bearing 3
Hex Socket Head Bolt M4x8
Set Plate
25
26
27
*
214020-0
922107-1
163157-9
961017-7
911143-2
655000-B
P.H. Screw M4x22 (With Washer)
Plug (For Car Lighter)
100
11-2001
Item
No.
Description
Type 1
Type 2
Type 3
Type 4
Motor D.C. 9V
(With Item 16)
1
629544-7 (No
Longer Available) Longer Available)
629578-0 (No
629581-1
Housing Set
15
25
410995-3 (No
Longer Available)
414344-6 (No
Longer Available)
182406-5 (Set)
(Old 414975-1)
Housing Set
410996-1 (No
414345-4 (No
182406-5 (Set)
Longer Available)
Longer Available)
(Old 414976-9)
Gear Com.
Spur Gear
3
153157-7 (No Longer Available)
221920-7 (No Longer Available)
343456-7
153202-8
221882-9
16
24
7
Shoe
343875-7
Slider / Slider Com.
164774-8
154401-5 (Includes
Slider - 164964-3,Ä
Felt - 443063-7,
Spring Pin 1.5-10 - 258017-9Ä,
Blade Clamp - 313057-5,
Pin 2 - 256672-1Ä)
Felt
9
443063-7
(Now part of Slider Com.)
Blade Set
10
344979-8 (334032-8)
(Now called Blade Clamp
and part of Slider Com.)
Serial # for 4390D
~ 508035E
~ 18926E
508036E ~
578516E
578517E ~
599230E
599231E ~
Serial # for 4390DW
18927E ~ 41412E
41713E ~
41915E
41916E ~
Ä Non-inventory Item
Type 1 to Type 4 parts are completely interchangeable as a set.
Type 3 Motor and Gear Com. can replace Type 2 Motor and Gear Com.
Type 4 Housing can replace Type 2 and Type 3 Housing.
Service Notes
1. Type 2 Motor will fit into Type 1 Housing if the following parts are added.
3 Model 4390D
3 Model 4390DW
2. New method of installing Blades (For Type 4 Slider Com.)
Tighten the bolt se curely while
mak ing sure that the blade will not
be ex tracted even though you try to
pull it out.
Loosen the blade se cur ing bolt fully
Fit the pin on the slider in the hole in the
blade shank.
with the hex wrench. Keep the back
edge of the blade fit ting into the roller
and in sert the blade be tween the blade
clamp and the slider as far as it will go.l
Make sure that you are in sert ing the
blade into the proper po si tion.
Note:
The hole in the blade shank will be aligned
with the pin on the slider when the blade
shank hits against the spring pin on the
slider.
CAUTION:
If you tighten the bolt with out the pin
on the slider fit ting prop erly in the
hole in the blade shank, the pin or
the blade shank will be dam aged.
This may cause the blade to be
extractedunexpectedlyduring
operation.
4 Model 4390D
4 Model 4390DW
|