Magnadyne Two Way Radio M11RF LCD User Manual

User’s Manual  
4
5
C
4/5/6  
Two-Way Communication LCD Transmitter  
Model: M11RF-LCD  
For Technical Assistance, please call (800) 638-3600,  
 
Remote Control Transmitters Operation  
Transmitter Button  
System Function  
Remark  
Lock Doors & Arm System  
Press and Hold  
for 3 Seconds  
Panic Function  
Car Locator  
Under Armed Mode  
Arm and Delete the 2 Stage  
Shock Sensor  
Press Twice within  
3 Seconds  
-
Silent Arming/Disarming  
Active Anti-Car Jacking Mode  
Channel #4 Timer Output (4)  
Channel #5 Timer Output (5)  
Channel #6 Timer Output (6)  
Unlock Doors & Disarm System  
Ignition in “OFF” Position  
+
+
Ignition in “ON” Position,  
Press and Hold for 2 Seconds  
+
+
+
Two Steps Door Unlock and  
Disarm System  
Press Twice within 3 Seconds  
Press and Hold for 2 Seconds  
-
Trunk Release  
Channel 3  
Passive Arming  
Bypass  
While the System  
is in “Disarmed” Mode  
-
Arm System and  
Hidden Alarm Function  
Press within 3 Seconds  
-
( )  
Activate or Turn Off  
the Remote Start  
Press Twice within 3 Seconds  
-
3
 
LCD Display Transmitter Operations  
Transmitter Button  
System Function  
Remark  
Press within  
3 Seconds  
-
Systems Trigger Record Check  
SET  
(C)  
Press within  
3 Seconds  
-
-
SET SET  
(C)  
System’s Status Check  
Button Lock  
Press within 3 Seconds and Hold  
“Lock” Button for 2 seconds  
-
=
SET  
Press within  
3 Seconds  
-
-
=
Optional Driving Pager  
Monitor Interior Temperature  
Daily Timer Start  
SET  
SET  
SET  
Press within  
3 Seconds  
=
Press within  
3 Seconds  
=
-
LCD Screen Lamp  
Turns ON for 5 Seconds  
Press and Hold for 1 Second  
SET  
Clear the Flash Icon and Melody  
Sound on the LCD Screen Transmitter  
SET-SET-SET  
Button Lock:  
Button Lock is useful if you want to disable the transmission function of the remote control  
temporarily to prevent from any inadvertent pressing of buttons by others.  
The regular remote control transmitter:  
Press the  
button first, within 3 seconds press and hold the  
button for 2  
seconds to activate or cancel the button lock function. The “LED” will pause flash for a few  
seconds to indicate the remote control transmitter is on “Button Lock” mode while pressing  
the transmitter button.  
The 2-Way remote control transmitter:  
Press the SET button first, within 3 seconds press and hold the  
seconds to activate or cancel the button lock function.  
button for 2  
Note: The  
Lock” mode.  
icon will display on the LCD screen to show the remote transmitter is in “Button  
Chirp Indicators  
Chirp  
Function  
1 Chirp  
2 Chirps  
3 Chirps  
4 Chirps  
5 Chirps  
System is Armed  
System is Disarmed  
Defective Reminder  
Disarm / Triggered  
Car Locator  
4
 
LED Display  
LED  
Function  
OFF  
System is Disarmed  
Slow Flashing  
Flash  
Fast Flashing  
System is Armed  
System in Passive Starter Disable  
System in Passive Arming  
System in Valet Mode  
Zone 1, Warn Away Trigger  
Zone 2, Trigger on Trunk/Hook  
Zone 3, Trigger on Door Switch  
Zone 4, Trigger on Shock Sensor  
Zone 5, Trigger on Ignition Switch  
On Solid  
2 Flashes - Pause  
3 Flashes - Pause  
4 Flashes - Pause  
5 Flashes - Pause  
Parking Light  
Flash  
Function  
1 Flash  
System is Armed  
System is Disarmed  
Disarmed / Triggered  
Car Locator  
2 Flashes  
3 Flashes  
12 Flashes  
Constant On  
Under Remote Start  
System Characteristics  
Siren/Horn Parking Light  
1 or 3 Chirps 1 Flash  
2. Disarming 2 or 4 Chirps 2 or 3 Flashes  
LED  
Doors  
Starter Dome Light  
1. Arming  
Slow Flash Locking Disabled  
Unlocking  
Turns on for  
30 Seconds  
3. Trigger  
Alarming  
Flashes  
Slow Flash  
Fast Flash  
Disabled  
Disabled  
Flashes  
4. Passive  
Starter  
Disable  
5. Panic  
Alarming  
Alarming  
6 Chirps  
Flashes  
Flashes  
Flashes  
Flashes  
6.Car  
Jacking  
Disabled  
7.Car  
Locator  
12 Flashes  
Locking  
5
 
Active Arming: Lock & Arm  
1.Press the button on the transmitter.  
2.The siren will chirp once and parking lights will flash once indicating that the system is now  
armed. The vehicle door will lock upon arming when interfaced with the security system.  
System Armed  
Door Ajar  
Trunk/Hood Ajar  
Clear the Flash Icon:  
Press the SET button 3 times  
within 3 seconds to clear the  
flash icon on the LCD screen  
transmitter.  
Defective Sensor Reminder:  
If the siren sounds 3 times, there is a Door, Trunk, or Hood left open. (See Alarm Feature I-4)  
Silent Arming/Disarming:  
Press the transmitter  
or  
button at the same time will arm or disarm your security system,  
No chirp sound will be heard, arm/disarm confirmation will be through the vehicles  
parking lights only.  
Shock Sensor Bypass:  
Press the button on the transmitter two times within 3 seconds. This will arm the security  
system and bypass the shock sensor. The system will chirp one additional time to confirm the  
sensor bypass mode was activated. The sensor bypass feature is programmed to activate for one  
arming cycle only. The security system will return to normal operation during the  
next arming cycle.  
Passive Arming:  
Active arming/disarming is controlling your security system via the remote transmitter. This  
security system is equipped with an optional passive arming feature which allows the security  
system to arm 30 seconds after the last door is closed. Operation is as follows:  
1. Turn the ignition to the “OFF” position and exit the vehicle.  
2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you  
reopen any Door, Hood, Trunk, the security system LED will stop flashing. It will begin flashing  
again once the vehicles entrances are closed.  
3. After the 30-second timer has elapsed, the security system will automatically “ARM”. The  
siren/horn will chirp once and the parking lights will flash once also.  
Passive Arming with Passive Door Locking (See Alarm Feature 1-2 Programming)  
The vehicle doors will automatically lock after passive arming cycle has been completed.  
Passive Arming Bypass  
While the system is in disarmed mode, press the  
button twice. The horn/siren will respond  
with one chirp and the LED will turn “ON”. The security system will remain in this mode for as  
long as you wish. To exit this mode press the or buttons and the system will return to normal  
status.  
6
 
Active Disarming Unlock & Disarm  
1. Press the button on the transmitter.  
2. The siren will chirp twice and parking lights will flash twice indicating that the system is now  
disarmed. The vehicle door will unlock and the dome light will turn on for 30 seconds upon  
disarming when interfaced with the security system.  
System Disarmed  
Doors Triggered  
Trunk/Hood Triggered  
Shock Sensor Triggered  
Ignition Triggered  
Clear the Flash Icon:  
Press the “SET” button 3 times within 3 seconds  
will clear the flash icon on the LCD screen  
transmitter.  
Tamper Disarming:  
If the security system is triggered, upon disarm, the siren will chirp 4 times and parking lights will  
flash 3 times.  
Pathway Illumination:  
This feature turns the parking lights “ON” for 30 seconds upon a unlock signal and for 10 seconds  
upon the lock signal.  
Two Steps Door Unlock:  
This feature will independently unlock the drivers door only when disarming the security  
system. Pushing the button a second time within 3 seconds will unlock the other doors.  
Automatic Rearm:  
If this feature is selected, the security system will automatically rearm itself within 60 seconds  
after disarming with the remote transmitter. Automatic re-arm will cancel if any door is opened  
before the 60 second timer is up.  
Disarming without a Transmitter:  
The override function may be used if the remote transmitter is lost or inoperative.  
1. Enter the vehicle and turn the ignition switch to “ON” position (alarm will sound).  
2. Within 10 seconds push and release the valet switch, the alarm will stop sounding and enter  
the disarm mode. You can now start and operate the vehicle normally.  
7
 
(System in Disarm or Valet Mode)  
Valet Mode  
The valet switch allows you to temporarily bypass all alarm functions eliminating the need to hand  
your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all  
alarm functions and remote start functions are bypassed, however the remote panic feature and  
remote door locks will remain operational. To use the valet mode, the system must first be  
disarmed either by using your remote transmitter, or by operating the manual override sequence.  
Remote Door Lock  
Remote Door Unlock  
Enter the Valet Mode:  
1. In the disarmed mode, turn the ignition to “ON”  
position.  
2. Push and hold the valet switch for 2 seconds  
until the LED turns on solid. The LED will  
remain on solid while the unit is in the valet  
mode.  
Exit the Valet Mode:  
1. To return to normal operation, turn “ON” ignition.  
2. Push and hold valet switch for 2 seconds. The LED will turn off to indicate the system is now  
out of the valet mode.  
Car Locator  
While in the armed mode, press the  
button to activate car locator function. The siren/horn will  
chirp six (6) times. The parking lights will flash 12 times to help you locate your car.  
Panic Function  
The transmitter can be used as a remote panic switch to manually trigger the alarm system in case  
of an emergency.  
1. Press and hold the  
button for 3 seconds. The security system will begin to sound and  
the parking lights will begin to flash.  
2. During panic mode, the normal functions of this transmitter becomes temporarily inoperable.  
The transmitter  
(if the option is installed), however, once the  
and  
buttons can be used to lock and unlock the door  
button is pressed, the vehicle’s starter  
disable device, (where installed) will be enabled allowing the vehicle to start.  
3. To stop the alarm, press and hold the transmitter or  
buttons on the  
transmitter again for 3 seconds. Also, if any transmitter button other than or is pressed and  
release, the panic mode will be turned off immediately.  
4. If the button is not pressed, the alarm will automatically stop after 30 seconds.  
Trigger the System  
When armed, your vehicle is protected as follows:  
1. Light impact will trigger the warn-away signal.  
2. Heavy Impacts/Doors Open/Hood Open/Trunk Open/Ignition Key Activated will trigger the  
programmed sequence. The starter disable relay (if installed) prevents the vehicle’s starter from  
cranking. The siren, horn, parking lights and dome light will turn on to alert of an intrusion for  
60 seconds. If one of the sensors or detectors are still active, the security system will sound a  
maximum of 6 times for 30 seconds.  
8
 
(Continued)  
Trigger the System  
Ignition Trigger (Clear the Flash Icon and Melody Sound):  
When the Security System is triggered, the LCD screen will alert the user through melody sound  
and flashing icons. By pressing the “SET” button 3 times within 3 seconds it will clear the flashing  
icons and stop the melody sound.  
Stop the Melody Sound:  
When the Security System is triggered, it will alert the user with flashing icons on the LCD Display  
and audible melody sound. To stop the melody sound, press any button on the LCD transmitter.  
Doors Triggered  
Trunk/Hood  
Triggered  
Warn Away  
Trigger  
Shock Sensor  
Trigger  
Ignition  
Trigger  
Noise Abatement:  
This security system has a “Noise Abatement Circuit”. This circuit prevents annoying, repetitive  
false alarms by filtering out environmental conditions.  
If the security system is triggered five times or more, the circuit will interpret this as a false alarm.  
After the fifth trigger, the noise abatement circuit ignores, or bypasses that switch or sensor until  
the next switch or sensor is activated.  
Noise Abatement Circuit covers doors, hood and trunk switches differently. If the security system  
is triggered by one of these switches for three cycles, the switch will be bypassed until the trigger  
ceases.  
Anti-Car Jacking  
Warning: This security system has a car jacking feature. Its default setting is “OFF”. So, be sure to  
enable this feature if you feel it is needed.  
Active Anti-Car Jacking  
1. Press and hold the transmitter  
and  
buttons at the same time for 2 seconds while the  
vehicle’s ignition is “ON” and all doors are closed. The parking lights will turn on for 1.5  
seconds to indicate this feature.  
2. Once the system is armed, and you are forced from your vehicle, the system will trigger when  
the door is opened and closed while the ignition is “ON”.  
Passive Anti-Car Jacking  
1. Turn the ignition switch to the “ON” position, the system will arm.  
2. Once the system is armed, if you are forced from your vehicle, the system will trigger when the  
door is opened and closed while the ignition is “ON”.  
9
 
(Continued)  
Anti-Car Jacking  
Trigger the Anti-Car Jacking Mode  
Three Timer circuits will function as follows:  
First Timer Circuit  
1. 50 seconds after the car jacking mode has been activated, the siren will begin to sound for 15  
seconds.  
2. During the 15 second activation period, you will be alerted to push the valet switch once to  
turn off the car jacking feature.  
3. If by now the valet switch has not been pushed, it will enter the second timer circuit.  
Second Timer Circuit  
65 seconds after the system has been triggered, the siren starts sounding and the parking lights  
start flashing.  
Third Timer Circuit  
90 seconds after the security system has been triggered:  
1. The vehicles siren is still sounding, parking light are flashing  
2. The starter disable mode will activate to prevent the vehicle from starting  
3. It will remain active until the vehicles battery power is exhausted  
Override the System to Turn Off Anti-Car Jacking  
Turn the ignition switch from OFF to ON and within 10 seconds, push the valet switch. The siren  
will stop sounding and the security system is now disarmed.  
Systems Trigger Check  
Press the transmitter “SET” button first, within three seconds press the  
(C) button. The transmitter will respond with one melody sound and all  
trigger’s records will immediately displayed on the transmitter LCD screen.  
System Status Check  
When you want to check the security systems present status through the transmitter LCD, press the  
transmitter “SET” button twice, within three seconds press the (C) button. The security system  
responds with one melody sound and the LCD screen should be illuminated.  
Driver Paging  
It is useful in the event that someone wants to page the driver of the parked vehicle. (Optional)  
Inside the Vehicle Paging  
With the ignition switch in the "OFF" position, press the valet switch for 2 seconds to page the  
driver. One chirp will sound from the vehicle and the LCD transmitter will begin to sound with a  
melody. The  
icon will then appear on the LCD transmitter to confirm this function.  
Outside the Vehicle Paging  
To page the driver from outside of the vehicle, "Knock" on the windshield glass to activate the LCD  
transmitter with a melody sound. The  
icon will then appear on the LCD screen (only when the  
optional knock sensor, model # M10-Page, is installed).  
10  
 
(Continued)  
System Status Check  
1. First press the SET button on the transmitter, within 3 seconds press the  
buttons to  
activate outdoor driver paging function. The vehicle will then respond with chirps from the  
horn/siren and a melody sound from the LCD transmitter. The  
LCD transmitter screen.  
icon will then appear on the  
2. When the windshield knock sensor is activated, the vehicle will then respond with chirps from  
the horn/siren and a melody sound from the LCD transmitter. The  
the LCD transmitter screen.  
icon will then appear on  
3. A. Turn on the ignition switch or press the button to arm the system.  
B. Press the button to disarm the system. This will then exit this function.  
Dome Light Supervision  
The Security System has a unique feature for using your vehicle’s dome light.  
1. Upon disarming the vehicles security system, the interior dome light will remain on  
for thirty seconds.  
2. If the security system is triggered, the dome light will flash for the same duration  
as the horn/siren.  
Ignition Controlled Door Locks  
If the vehicles door locks have been interfaced with the security system, the system will  
automatically lock the vehicle’s doors when the ignition key is turned to the “ON” position and or  
unlock the doors when ignition key is turned to the “OFF” position.  
Channel 3: Trunk Release Output  
Press and hold the  
button for two seconds to activate the trunk release  
(Channel 3 output) and/or any other devices connected.  
Channel 4: Timer Control Output  
Press and hold the and  
button at the same time to activate the Channel 4 output.  
Channel 4 is user programmable output. You may program the built in timer to send a ground  
signal for any time duration from 1 second to 120 seconds.  
Channel 5: Timer Control Output  
Press and hold the  
and  
button at the same time to activate the Channel 5 output. Channel 5  
is user programmable output. You may program the built in timer to send a ground signal for any  
time duration from 1 second to 120 seconds.  
Channel 6: Timer Control Output  
Press and hold the  
and  
button at the same time to activate the Channel 6 output. Channel 6  
is user programmable output. You may program the built in timer to send a ground signal for any  
time duration from 1 second to 120 seconds.  
Note: These timer outputs (4-6) may be used to turn on the Headlights, Power Windows or Power  
Sunroofs (Factory Settings are Momentary Outputs).  
11  
 
Remote Start Operation  
To Remote Start Your Vehicle by Using the Remote Transmitter:  
1. Press the button twice on the remote transmitter.  
2. The parking lights will turn “ON” to indicate the remote start is activated.  
3. The engine will start in approximately 5 seconds.  
4. Once the engine is running, the parking lights will turn back on to indicate climate controls are  
activated to your pre-settings (While the vehicle is running, the “minute” digits will appear  
flashing on the LCD screen of the transmitter. It will indicate the count down timer based on the  
5, 10, 20 or 30 minute run time set up by your installation center).  
5. The vehicle will run for 5 to 30 minute cycles and automatically shut down (When the unit  
shuts off the count down timer will turn off and the transmitter will play a melody tune).  
Note: The Remote Start unit will not start if any of these conditions exist:  
1. The hood is opened.  
2. The brake pedal is pressed.  
3. Move the optional remote start enable toggle switch to “OFF” position (if installed).  
4. The gear selector is in any gear other than “Park” or “Neutral”.  
Safe Start (Child Safety Mode):  
The factory default setting to remote start your vehicle is to press the button twice. If the child  
safety mode has been activated, press the  
the vehicle.  
and the  
buttons at the same time to remote start  
To Operate the Vehicle While in the Remote Start Feature:  
1. Insert the Ignition key, turn it to the “ON” position “NOT THE START POSITION”.  
2. Press the brake pedal.  
Note: If the Brake Pedal is pressed before the key is in the “ON” position, the engine will  
automatically shut off.  
Temporary Stop Feature:  
This feature allows the vehicle to remain running after the key has been removed from the  
ignition. This feature is useful for occasions when you wish to exit and lock the vehicle for short  
periods of time. This will keep the engine running for climate controls to stay on.  
1. Before turning the engine off with the ignition key, press the  
three times to indicate the feature is activated.  
button once. The LED will flash  
2. Turn the ignition key to the “OFF” position (the engine will stay running).  
3. The engine will run until the pre-programmed time elapsed or shutdown input is received.  
12  
 
Remote Start Operation  
Timer Start:  
This unit can be programmed to start and run the engine every 3 hours, 2 hours or punctually at  
the same time every morning. The engine will run for the programmed running time and then shut  
down.  
Important! Timer start should be used only in open areas. Never start, or most importantly leave a  
vehicle running in an enclosed area.  
3 or 2 Hour Timer Start with Temperature Control Off:  
This feature is designed for an extreme cold climate usage. The system will auto start the  
vehicle every three hours to prevent the engine from freezing and creating a hard-to-start  
condition. A MAXIMUM OF SIX CYCLES CAN OCCUR.  
3 or 2 Hour Timer Start with Temperature Control On:  
The system can be programmed to automatically start the vehicle’s engine whenever the  
temperature inside the vehicle reaches and/or drops below a pre-programmed temperature  
level. There are three temperature levels to choose from. A MAXIMUM OF SIX CYCLES CAN  
OCCUR.  
Daily Timer Start:  
Press the “SET” button first, within three seconds press the  
button. The parking lights will  
flash six times and the siren/horn will sound six times. The vehicle is now programmed to start the  
next day.  
Exit the Timer Start:  
Timer start can be stoped manually as follows:  
1. Make sure the remote start system is not operating  
2. Turn the ignition “ON”. The LED and parking light will flash four times. The horn/siren sounds  
for four times. Or:  
1. Press the  
parking light has turned ON or are flashing  
2. Immediately press the button then press and hold the  
button twice to remote start the vehicle. As soon as the vehicle is running and  
button for two seconds. The  
parking light will flash four times. The siren/horn will sound four times. The vehicle is no  
longer programmed to start automatically.  
Interior Temperature Check  
The temperature sensor can monitor the vehicle’s interior temperature through the LCD transmitter.  
1. Press the SET button, within 3 seconds press the  
displayed on the LCD transmitter.  
buttons. The interior temperature will be  
13  
 
Turn Off Remote Start  
When the engine is running by remote start and you wish to stop the engine from remote start:  
1. Press the  
button twice on the remote transmitter.  
2. Move the optional remote start toggle switch to the “OFF” position (if installed).  
3. Press the vehicle’s brake pedal, the engine will stop running and the parking lights turn off to  
indicate the engine has stopped.  
Shut Down Input for Remote Starter  
If any of the following conditions exist while the system is operating, the engine will not start or will  
shut down immediately:  
1. The hood is opened.  
2. The brake pedal is pressed.  
3. Engine is over reeved (Tachometer Type Only).  
4. The pre-programmed run time (5-10-20-30 minutes) has elapsed.  
5. Press the button once on the remote transmitter while in remote start mode only.  
6. Move the optional remote start enable toggle switch to “OFF” position (if installed).  
7. The vehicle refused to start running after 3 unsuccessful attempts.  
(Also See Installation Manual)  
Turbo Timer Mode  
Turbo Timer Mode keeps the engine running after arriving at you destination for a programmable  
time period of 1, 3 or 5 minutes. This allows the system’s time to conveniently cool down the turbo  
after you have left the vehicle.  
To Activate:  
1. While the engine is running, set the emergency brake and place the transmission to "Park".  
2. Before turning off the engine, press and release  
and  
buttons at the same time. The light  
will flash to indicate the remote start has entered turbo charge mode.  
3. Remove the “Ignition Key” from the key cylinder. The engine will keep running.  
4. Exit and secure the vehicle. The Engine continues running until the pre-programmed time  
elapsed.  
Interference  
Note: The transmission range may  
become shorter if the system is  
interfered by a stronger radio  
frequency from sources of high  
6
Bi  
voltage electric power or obstacles  
like tall buildings. The transmitter  
SET  
uses low output powered  
frequency.  
4
5
C
4/5/6  
14  
 
Remote LCD Icons  
Door Lock  
Lock your Vehicles Doors  
Door Unlock  
Unlock your Vehicles Doors  
Armed Mode  
Timer Control Start  
Automatic Engine Start (Timed)  
Temperature Monitor  
Monitors the Temperature Inside  
Vehicle  
Security System is Armed  
Valet Mode  
Time Monitor  
Displays Time  
Security System is Armed  
Remote Transmission  
Transmitting a Signal  
In-Range Indicator  
You are within Remote Range  
Door Triggered  
Alert Alarm  
Alarm Timer  
Count Down Monitor  
Power Save Mode  
Saves The Battery Power when  
Transmitter is not in Use  
Vibrate Mode  
Doors are Opened  
Trunk/Hood Triggered  
Trunk/Hood are Open  
Shock Sensor  
Vibrates when Security System is  
triggered  
Button Lock  
Shock Sensor Triggered  
Warn Away  
Disables Transmission Function  
Temporarily  
(Zone 1) Shock Sensor Triggered  
Ignition  
Engine Starting by Remote  
Engine Running  
Paging  
A Page Signal is being Received from  
your Vehicle  
Low Battery  
Replace the Battery with Alkaline AAA  
size  
Your Vehicles Engine is Running  
15  
 
Programming of the LCD Transmitter  
Button  
Description  
Operation  
LCD Screen Lamp Turns ON for  
Five Seconds  
Press and Hold for 1 Second  
1 Melody Sounds to Confirm  
Press and Hold for 3 Seconds  
2-Melody Sounds to Confirm  
Press and Hold for 5 seconds  
1 Melody Sounds to Confirm  
SET  
Timer Programming Mode  
SET  
Power Save Mode  
SET  
SET (3X)  
Clear the Flash Icon and Melody Sound Press within 3 Seconds  
on the LCD Screen  
SET & LOCK  
Button Lock Enabled/Disabled  
Press within 3 Seconds  
SET & UNLOCK Melody/Vibrate Mode  
Program Count Down Timer  
Press within 3 Seconds  
Press within 3 Second Cycles  
Leave the Buttons Starting Count  
Down then Timer Icon Flashes  
SET &  
(10 m, 20 m, 30 m, 1 hr, 1.5 hr, 2 hr)  
Enable/Disable Beep Sound while  
Pressing Button  
SET &  
Press for 2 Seconds  
Programming the LCD Transmitter  
Screen Lamp On:  
Press and hold the “SET” button one second, with the melody sound and the LCD screen lamp  
will turn on for 5 seconds.  
Power Save Mode:  
While in the Power Save Mode, the LCD transmitter uses “0” current to save the battery power.  
1. Press and hold the “SET” button for 5 seconds. One melody will sound from the transmitter  
and the LCD will show “SAVE”. You are now in the “Power Save Mode”.  
2. Under the Active Arming Mode and Disarm Mode. Turn the ignition switch to the “ON” position.  
The LCD remote transmitter will automatically enter the “Power Save Mode”  
Exit Power Save Mode:  
Press any button on the LCD transmitter to exit the Power Save Mode.  
Clear the Flash Icon and Melody Sound:  
Press the SET button 3 times within 3 seconds and it will clear the flashing icon and melody  
sound on the LCD transmitter.  
Stop the Trigger Melody:  
While triggering the alarm, the LCD screen will alert the user through melody sound and flashing  
trigger icon. Press any button on the transmitter to stop melody sound only.  
Button Lock:  
Use this mode to disable the transmission function of the remote control temporarily to prevent  
any inadvertent pressing of buttons.  
1. Press the “SET” button first, within 3 seconds press and hold the  
button for 2 seconds to  
activate or cancel the button lock function. The icon will be displayed on the LCD screen to  
show button lock mode.  
16  
 
Programming the LCD Transmitter  
Vibration/Melody Mode: This mode is useful when you are in a noisy place and it is difficult to hear  
the beep from the remote. The LCD transmitter will vibrate if your security system has been  
activated.  
Press the “SET” button first, within 3 seconds press the  
(
) button for 2 seconds to select the  
mode of vibrate/melody. The  
icon will be displayed on the LCD screen to show mode.  
Set-Up Fixed Count Down Timer:  
Press the “SET” button first, then within 3 seconds press and hold the  
The LCD screen will show the icon and timer (0:10). Press the  
desired time.  
button for 2 seconds.  
button again to choose the  
Out of Range Indication:  
1. If the Transmitter is within range, the  
icon will display on the LCD screen.  
2. If you are out of range, the  
times.  
icon will disappear from LCD Screen and transmitter will beep 5  
Timer Setting  
Button  
Description  
Operation  
for (-) and  
Press and Hold SET  
Button for 3 seconds  
Time Setting (Hour)  
Flash Digit for Adjusting  
(+)  
Press the SET  
Button Once  
Time Setting (Min.)  
Flash Digit for Adjusting  
for (-) and  
for (-) and  
for (-) and  
for (-) and  
(+)  
(+)  
(+)  
(+)  
Press the SET  
Button Once  
Alert Alarm Time Setting (Hour) Flash  
Digit for Adjusting  
Press the SET  
Button Once  
Alert Alarm Time Setting (Min.) Flash  
Digit for Adjusting  
Press the SET  
Button Once  
Alert Alarm Setting ON/OFF  
Count Down Timer Setting (Hour) Flash  
Digit for Adjusting  
Press the SET  
Button Once  
for (-) and  
(+)  
(Max 19 Hrs. 59 Min.)  
Count Down Timer Setting (Min.) Flash  
Digit for Adjusting  
Press the SET  
Button Once  
for (-) and  
(+)  
Press the SET  
Button Once  
Count Down Timer Setting ON/OFF  
for (OFF) and  
(ON)  
Press and Hold  
button for 2 seconds  
Daily Timer Start Timer Setting  
for (-) and  
(+)  
Flash  
/
Icon and hours for Adjusting  
17  
 
Replacement Parts and Accessories  
TRANSMITTERS  
DESCRIPTION  
MODEL #  
$ PRICE  
5-Button Transmitter for  
M11a Security System.  
M11RF-LCD  
139.95 ea.  
4
5
C
4/5/6  
4-Button Transmitter with  
SAW Technology for  
M11RF  
59.95 ea.  
M11a Security System.  
BATTERIES  
1.5 Volt AAA Alkaline Battery commonly  
found in grocery stores, hardware stores,  
etc.  
CR2025 - 3 Volt Lithium Battery (2 pcs.)  
Models:  
Radio Shack: #23-161  
Duracell: #DL2025  
Eveready: #ECR2025  
Panasonic: # CR2025  
18  
 
Parts and Accessories Order Form  
Mail to: Magnadyne Corporation  
ATTN: Consumer Parts Sales  
P.O. Box 5365  
Credit Card or Money Order Only  
(Sorry No Cash, C.O.D. or personal checks accepted)  
Call: (310) 884-7777 Fax: (310) 637-9542  
Carson, CA 90749-5365  
SHIP TO: (No P.O. Boxes)  
LAST NAME  
FIRST NAME  
INITIAL  
STREET ADDRESS  
ADDITIONAL ADDRESS  
ADDITIONAL ADDRESS  
CITY  
STATE  
ZIP CODE  
DAY TIME PHONE NUMBER  
CREDIT CARD INFORMATION  
VISA  
MC  
CREDIT CARD N0.  
CARD HOLDER’S LAST NAME  
STREET ADDRESS  
CITY  
EXPIRATION DATE  
FIRST NAME  
INITIAL  
STATE  
QTY.  
ZIP CODE  
PART #  
DESCRIPTION  
PRICE EACH  
TOTAL  
Shipping and Handling  
Sales Subtotal = ________ . ______  
Up to $20.00  
20.01 to 30.00  
30.01 to 45.00  
45.01 to 70.00  
Over 70.01  
$5.00  
5.95  
6.50  
6.95  
7.95  
California Residents Add Sales Tax = ________ . ______  
Shipping and Handling (See Chart) = ________ . ______  
TOTAL = ________ . ______  
On regular orders please allow 4-5 weeks for delivery.  
Please give a shipping address where this order may be delivered between the hours of 9 am and 5 pm weekdays.  
If UPS is unable to deliver, your order will be returned and additional shipping charges will be required.  
19  
 
Limited Lifetime Warranty  
Magnadyne Corporation or its authorized agents will, for the life of the vehicle and to the original  
purchaser, repair, replace or refund the retail sales price of said product or any part thereof, at the  
option of the Magnadyne Corporation or its authorized agents, if said product or part is found  
defective in materials or workmanship, when properly connected and operating on the correct  
power requirements designated for the specific product. This warranty and Magnadyne Corporation  
or its authorized agents obligations, hereunder do not apply where the product was: damaged while  
in the possession of the consumer, subjected to unreasonable or unintended use, not reasonably  
maintained, utilized in commercial or industrial operation, or serviced by anyone other than  
Magnadyne Corporation or its authorized agent, or where the warning seal on the product is broken  
or the power plugs or wires are detached from the unit. Magnadyne Corporation or any of its  
authorized agents do not assume any labor costs for the removal and reinstallation of any product  
found to be defective, or the cost of transportation to Magnadyne Corporation or its authorized  
agents. Such costs are the sole responsibility of the purchaser.  
This warranty does not cover the cabinet, appearance items, normal wear and tear or accessories  
used in connection with the product resulting from improper installation, alteration, accident,  
misuse, abuse or acts of nature.  
This Limited Life Time Warranty applies only to the receiver section of the security system. Neither  
the siren, transmitters, wire harness or any accessory item added to or used with a Remote Mobile  
security system are covered by this Limited Life Time Warranty. Sirens, transmitters, wire harness  
or any accessory item are covered by our standard 12 month limited warranty.  
Magnadyne Corporation or its authorized agents shall not be liable to anyone for consequential  
or incidental damages or claims that may arise due to failure of product to operate properly  
except those accorded by law. Magnadyne's or its authorized agents liability to the repair,  
replacement of the product as stated above if all conditions of the warranty are met. No  
expressed warranty or implied warranty is given except those set forth herein. Magnadyne does  
not warrant or guarantee against break in damage or the theft of the vehicle in part or whole, or  
against the loss or damage to the contents of any vehicle in which a security system is  
installed. Magnadyne security systems are only a deterrent against possible theft.  
This warranty extends only to the original purchaser of the product and for the vehicle in which it  
was originally installed. This warranty is not transferable or assignable to any person or vehicle.  
Defective merchandise should be returned to the original point of purchase or secondly to  
Magnadyne Corporation, 1111 W. Victoria Street, Compton, CA 90220. A return authorization must  
be obtained before sending, or merchandise may be refused.  
M11RF-LCD-UM 2-10-04 Rev. A  
© Copyright 2004 Magnadyne Corporation  
 

KWC Indoor Furnishings 10031213 User Manual
KWC Indoor Furnishings 10211033000 User Manual
Link electronic Stereo Receiver PDP 886 User Manual
Linn Turntable BASIK User Manual
Locke Lawn Mower TRM 3083 User Manual
Lux Products Thermostat PSMH45 User Manual
Magic Chef Refrigerator MCBR240W User Manual
Makita Drill 6303H User Manual
Makita Drill 7104L User Manual
Metrologic Instruments Scanner IS4920 User Manual