DX-RVC Predefined Functions
DX-RVC
DX-RVC Remote Volume Control (2-button/12-LED)
Remote Volume Control
Switch Positions
Switch Positions
ID
1 through 8
00000100
10000100
01000100
11000100
00100100
10100100
01100100
11100100
00010100
10010100
01010100
11010100
00110100
10110100
01110100
11110100
00001100
10001100
01001100
11001100
00101100
10101100
Function
ID 1 through 8
Function
Quick-Start Guide
0
1
00000000
10000000
01000000
11000000
00100000
10100000
01100000
11100000
00010000
10010000
01010000
11010000
00110000
10110000
01110000
11110000
00001000
10001000
01001000
11001000
00101000
10101000
01101000
11101000
00011000
10011000
01011000
11011000
00111000
10111000
01111000
11111000
Input Level 1A (1)
Input Level 1A (2)
Input Level 1B (1)
Input Level 1B (2)
Input Level 2A (1)
Input Level 2A (2)
Input Level 2B (1)
Input Level 2B (2)
Input Level 3A (1)
Input Level 3A (2)
Input Level 3B (1)
Input Level 3B (2)
Input Level 4A (1)
Input Level 4A (2)
Input Level 4B (1)
Input Level 4B (2)
Input Level 5A (1)
Input Level 5A (2)
Input Level 5B (1)
Input Level 5B (2)
Input Level 6A (1)
Input Level 6A (2)
Input Level 6B (1)
Input Level 6B (2)
Input Level 7A (1)
Input Level 7A (2)
Input Level 7B (1)
Input Level 7B (2)
Input Level 8A (1)
Input Level 8A (2)
Input Level 8B (1)
Input Level 8B (2)
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54-255
Output Level A (1)
Output Level A (2)
Output Level B (1)
Output Level B (2)
Output Level A&B (1)
Output Level A&B (2)
Group Level 1 (1)
Group Level 1 (2)
Group Level 2 (1)
Group Level 2 (2)
Group Level 3 (1)
Group Level 3 (2)
Group Level 4 (1)
Group Level 4 (2)
Group Level 5 (1)
Group Level 5 (2)
Group Level 6 (1)
Group Level 6 (2)
Group Level 7 (1)
Group Level 7 (2)
Group Level 8 (1)
Group Level 8 (2)
Reserved for future
updates
The DX-RVC is a real-time remote volume
control for use with the DX8 Digital Audio
Mixer/Signal Processor. The DX-RVC can be
programmed to operate the volume for any of
the eight inputs, either output, grouped
outputs, or Group Levels 1-8. The predefined
functions are programmed via the eight DIP-
switches on the back of the circuit board. Up
to nine remote controls (including the DX-RVC
and the DX-SW4) can be connected to the DX8
REMOTE BUS connector.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Safety First!
Before connecting and using the
equipment, please read this Quick-Start Guide
carefully and keep it for future reference.
1. Never install, connect, or disconnect the
remote control with the DX8 power supply
on.
Each of the predefined functions has two IDs (1) and (2) to allow two remote controls
to perform the same function.
2. Before applying power to the DX-RVC, make
sure the wiring is correct as described in
this Quick-Start Guide.
WARNING! This equipment has been
designed to be installed by qualified
professionals only! There are many factors to
be considered when installing professional
sound reinforcement systems, including
mechanical and electrical considerations, as
well as acoustic coverage and performance.
Mackie Industrial strongly recommends that
this equipment be installed only by a
16220 Wood-Red Road NE Woodinville, WA 98072
TEL +888.337.7404, FAX +425.487.4337
professional sound installer or contractor.
Part No. 910-298-20 Rev. B 9/00
© 2000 Mackie Industrial. All Rights Reserved. Printed in the USA.
|