Millennium MkIV
True Digital Amplifier
Owners Manual
- 1 -
WARNINGS
CAUTION
RISK OF ELECTRICAL
SHOCK. DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
Explanation of graphical symbols
Exclamation symbol
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the product.
Lightning symbol
The lightning with arrowhead symbol within an equilateral triangle is intended to
alert the user to the presence of uninsulated “Dangerous Voltage” within the
products’ enclosure that may be of sufficient magnitude to constitute a risk of
electrical shock to a person.
- 3 -
Important safety instructions
1:Read these instructions carefully before installing or operating this apparatus.
2:Keep these instructions.
3:Heed all warnings.
4:Follow all instructions.
5:Do not use this apparatus near water.
6:Clean only with a dry cloth.
7:Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8:Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus that produce heat.
9:Do not defeat the safety purpose of the grounding-type plug. A grounding-type plug has
two pins and a third grounding prong. The third prong is provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10:Protect the power cord from being walked on or pinched, particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus. Do not use
this unit with a damaged cord or plug.
11:Only use attachments and accessories specified by the manufacturer.
12:Use only with cart, stand, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tipping over.
13:Unplug this apparatus during lightning storms or when unused for long periods of time.
14:Connect only to the proper mains voltage.
15:To completely disconnect this apparatus from the AC Mains, disconnect the power
supply cord plug from the AC receptacle.
16:Do not connect any output from the amplifier to any other amplifier's output or any other
voltage source.
17:Do not expose this apparatus to dripping or splashing and ensure that no objects filled
with liquids, such as vases, are placed on the apparatus.
18:To avoid electrical shock, make sure that no conductive part of the loudspeaker wiring is
exposed while the amplifier is operating. Do not connect loudspeakers with uninsulated
terminals to the amplifier.
19:Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as when the power-supply cord or plug
are damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally or has been
dropped.
- 4 -
Unpacking and placement of the Millennium
The Lyngdorf Millennium is heavy and has no built in handles. Unpacking it can be a little
bit tricky. To prevent back or toe injuries, we strongly recommend you get someone to help
you when it's time to lift the amplifier out of the box. Or open the box, fold out the carton
flaps, without removing any packaging material, carefully turn the box upside down and
simply remove the box from the amplifier.
When you have carefully removed the unit and accessory kit from the carton, visually
check for shipping damage. Contact both the shipper and Lyngdorf Audio immediately if
the unit bears any sign of damage from mishandling. All Lyngdorf Audio equipment is
carefully inspected before leaving our factory.
KEEP SHIPPING CARTON AND PACKING MATERIALS for future use or in the
unlikely event that the unit needs servicing. If this unit is shipped without the
original packing, damage could occur and void the warranty.
Place the Lyngdorf Millennium near the digital sources, thus keeping interconnects
reasonably short. The Millennium may be placed on a shelf or in a cabinet where it's easy
to operate.
Note that adequate clearance for the AC cord, speaker cables and interconnects must be
left behind the Millennium. Due to the Millennium's high efficiency, it won't get very warm
even after hours of operation. This will give you great flexibility in terms of placement. Just
make sure that the ventilation slots at the upper section of the back panel are not covered.
- 5 -
Accessories
You should find the following in the accessory kit:
1. One mains cord
2. This manual
3. Customer registration form
4. Remote control
5. RS232 Cable for firmware upgrade from a PC
6. Programming cable
Operating voltage
The Millennium is available in a version for 115V mains voltage and in a version for 230V
mains voltage.
Check the label on the Millennium rear panel and verify you have the version with the
proper voltage for your geographical area.
The 115V version requires a mains voltage of 100V-120V at 50-60Hz with a current rating
of 8A.
The 230V version requires a mains voltage of 200V-240V at 50-60Hz with a current rating
of 4A.
The mains voltage setting for your Millennium can be changed ONLY BY A QUALIFIED
ENGINEER.
WARNING: Connect the power input only to the AC source printed on the
label. The warranty will not cover any damage caused by connecting to the
wrong type of AC mains.
The Millennium has three power modes:
1. OFF – No circuitry is powered.
2. STANDBY – The mains transformer and amplifier section is powered off, only the
remote control input and the microprocessor is powered, so the unit can be
powered up using the remote control “STANDBY” button
3. ON – All circuits active
Product Registration
Please record the serial number of your amplifier here for future reference. The serial
number is printed on the label on the Millennium rear panel. You will need this serial
number, should you ever require service for your Millennium power amplifier.
Millennium MkIV serial number: _____________________
- 6 -
Introduction
Lyngdorf Millennium is the world's first true-digital power amplifier where digital audio data
is converted directly into sound without analog amplification or conventional low-level D/A
conversion involved at any step.
The core technology is based on patented EQUlBlT™ processing and output modules.
The Lyngdorf Millennium is a modular design, a platform for state-of-the-art music
reproduction. This means that you can add functions or upgrade the performance, as the
technology becomes available. This manual will expand together with your Millennium. If
you take the time to register your investment, we guarantee that you will get information
about future upgrades and expansions.
Features:
Hardware:
• Clocking of the PWM modulator is running in master mode at increased sampling
frequency which insures optimal performance in the audio band compared to other
implementations
• Ultra low phase noise / low jitter clock system extends the dynamic range and gives
extremely low jitter
• All digital signals on the PCB are noise optimized regarding transmission line load
to reduce interference to clock systems.
• Built in Audio DSP’s for Equalizers, crossovers delays etc.
• New Digital transceiver supporting 192kHz single wire interface
• New Asyncronous Sample Rate Converter with internal conversion rate always
clear of 1:1 conversion problems.
• Optimized low jitter clock system
• PC interface for programming, control and upgrades
• High-end Balanced DAC line out for active system setup
Performance:
• THD+N level -107dB A-weighted both channels driven at -60dB@1kHz
• THD+N level -104dB with both channels driven at -60dB@1kHz
• THD+N < 0.01% @1kHz 10W in 8 Ohms (<0.02% from 1-150W)
• THD+N < 0.015% @100W from 20-20 kHz
• Dynamic range 107dB digital plus 26 dB PSU variation - totals 133 dB
• DAC line out Dynamic range 116dB A-weighted
• DAC line out SN+THD ratio -105dB @ FS -1dB Output Both channels driven @
1kHz
• DAC linearity 20-20kHz +/-0.02dB
• ASRC THD+N -140dB (20Hz-Fs/2) Dynamic range 144 dB
Software:
• PC Interface for control of all built in functions, remote accessible via RS232
interface. Firmware upgradable from PC, DSP control software.
• 8 Presets with full storage of all filter parameters for A/B testing, different seating,
music modes etc.
• 20 band Parametric Equalizer and delays up to 7 meters per channel.
- 7 -
Quick set-up
A. Connect your speaker cables to the terminals on the back panel. The speaker
impedance should be 4-16 Ohms. If the speakers can be bi-wired, use both sets of
terminals. Make sure that the red (+) terminal gets connected with the corresponding
positive (+) terminal on your speaker. European versions of the Millennium will not accept
banana plugs. Do not attempt to remove the plastic safety plugs, use spades or simply
bare wires.
B. Connect your CD/DVD/MD/DAT player to one of the digital inputs or an analog source
to the A.l.M. Turn on the power to your source.
C. Turn on the Millennium with the power button (1).
D. Press the analog or digital (2/4) input selector once. The Millennium will now boot up
and you must select the input where you connected the source. If the Equibit logo is
flashing, press the input selectors 2 or 4 to find the right source. When the Millennium
detects a signal, the logo will stop flashing.
E. Adjust the volume with the wheel (3) to a moderate level.
F. Activate your digital or analog source and adjust the volume.
If you experience any problems during this procedure, please refer to the following
pages for a more detailed explanation of the set-up.
- 8 -
Front panel
Fig 1: Millennium front panel.
Controls
The buttons/controls on the front panel of the Millennium can all be used either with direct
presses on the front or by operating the similar keys on the included remote control. All
keys on the front except from the Mains switch (1) can be found on the remote control as
well.
(1) Mains switch. Powers the Millennium on/off. Standby mode is selected with the remote
control only.
(2) Analog input selector. The analog input selector is only active when the optional
Lyngdorf Analog lnput Module is connected to the Millennium.
(3) Volume control wheel & display*
(4) Digital Input selector
Changes to Digital input, or if already selected, cycles to the next Digital input.
The wheel (3)*
5) Lyngdorf logo & Standby indicator
6) Analog input indicator
7) Digital input indicator
8) Equibit logo & input lock indicator
9) Digital input indicator
- 9 -
Adjusting the volume
The volume can be adjusted by turning the big wheel or pressing volume up/down on the
remote control. The volume level is displayed in decibels (dB where 99.9dB is the
maximum setting giving full power for a full-scale input from a digital source. Note that no
clipping is possible. Some recordings may be recorded at a lower level that doesn't make
use of the full16 bit dynamic range of the CD. The Millennium will not deliver full power
with such records. The volume is adjusted in approx. 500 uniform steps of 0.1dB. The
value displayed is always rounded to 0.1dB resolution. However not all 3-digit volume
levels can be set, the value will increase with either 0.1dB or 0.2dB according to the
rounding number.
Pre-set Volume
When the Millennium is turned on, the volume is set to a pre-programmed value. This level
can easily be changed; adjust the volume to the desired level, press the A and D buttons
Simultaneously for 2 seconds. The display will confirm the setting by flashing the volume
and the amplifier automatically enters standby mode.
Maximum output level
The volume control with its low-friction, high precision ball bearings can easily spin up to
full output. To prevent damage to your speakers, a maximum volume level can easily be
programmed, you can find out how to do this in the section “Remote Control”.
Power
At a first glance, the operation of this very accurate dB scaled volume control may come
as a bit of a surprise. Normal operation will be at levels that seem to be very close to the
maximum power of the amplifier.
The dB’s scale is not linear
Volume level Corresponds to (at BA)
99.9dB………150 W
96.9dB………..75 W
92.9dB………..30 W
89.9dB………..15 W
82.9dB…………3 W
79.9dB………..1.5W
Keep in mind that the dB scale is not linear, a 10dB increase corresponds to 10 times the
power level and a 3dB increase equals 2 times the power.
Set the dimmer display light control
When the Millennium is in operational mode (ON), three levels of display-light settings are
possible. The DIM function on the remote control (explained later) toggles between:
A. Maximum light
B. Dimmed
C. Dimmed and volume display/input indicators off
Regardless of this setting, any change in display information activates maximum light for
two seconds.
- 10 -
Polarity
You can switch the polarity 180 degrees with the remote control (explained later). The
display confirms the polarity with either "pos" or "neg".
Mute
When "Mute" is activated from the remote control the display shows "---" and the amp will
be muted. Press the "Mute" button again to deactivate the mute status. If the volume is
changed when Millennium is muted, the display will show the volume for 3 seconds.
Advanced Set-up
Check the mains voltage!
Attempting to operate the Millennium at an incorrect voltage can damage the unit! Power
is supplied via the lEC-connector on the back panel. Neither the voltage nor the line
frequency setting may be changed by the user. Make sure that the label on the rear panel
of the Millennium indicates the correct AC operating voltage for your country.
When the power switch (1) is pressed - the standby circuitry, which controls the mains
relay will be activated. The amplifier will start in standby mode indicated by the red
Lyngdorf logo. After a few seconds, the amplifier can be switched into operational mode by
pressing any of the two input selector (2 or 4) buttons or using the power button on the
remote control. In operational mode, the display located in the wheel will be visible to bring
the amp back to standby mode, press the power button on the remote or press the input
selector buttons simultaneously for 2 seconds. This will also default the volume setting
(See section on volume control).
- 11 -
Rear panel
Fig 2: Millennium rear panel.
Do not cover or obstruct the ventilation slots on the rear panel.
1) Speaker terminals
2) AD Converter Input
3) D4 Input AES EBU
4) IEC Mains power connector
5) Digital Outputs D AES EBU
6) Digital Output D
7) RS 232 Input and Output
8) Speaker terminals
9) Digital Input D1
10) Digital Input D2
11) Digital Input D3A SPDIF
12) Digital Input D3B Optical
13) Analog Output R
14) Analog Output L
There are 4 digital inputs on the back panel corresponding to the 4 input indicators at the
right hand section of the display:
DI - RCA input
D2 - RCA input
D3A - Digital Input D3A SPDIF
D4B - Digital Input D3B Optical
The D (4) button on the front panel and on the remote control is used to toggle between
the inputs.
- 12 -
Clock Gate
A proprietary 5-pole XLR input is provided for a clock synchronised CD-transport, where
the reference clock is controlled by the Millennium. This feature is called Clock Gate.
When a compatible device is connected to the 5-pole connector (2) position D4 selects the
Clock Gate input as a source.
(This means that a Clock Gate source will override the AES/EBU input.)
Digital Output
The selected analog or digital input source is relayed to the digital output. Use the output
for recording CD’s etc.
Analog Inputs
One of the two 5-pole XLRs is dedicated for the optional Analog Input Module A.l.M.,
which will be clock synchronised and powered by the Millennium. When the A.l.M. is
connected, one of four analog inputs can be selected by toggling through input Al to 44.
When the A.l.M. is not present, the AI indicator will flash and the Millennium returns to the
previous digital input.
Address setting for network operation
When used in a network in connection with either a RCS/TCS or another Millennium it is
essential to set both the communication speed and address correctly. The address usage
in a network is restricted by the following rules:
Address
0
1
2-..
Functionality
Reserved
Master
Comment
Normally not used
Master, TCS, RCS
Slave
Slave
If more than one amplifier is present in the network different addresses must be appointed
to each amplifier by the Millennium software.
The INPUT/AUX connectors on the back panel are used for connectivity over standard
RJ12 cables in a suitable length. For Slave amplifiers the input is used to pass information
from the Master or a RCS/TCS to the amplifier. For Master amplifiers the broadcast
information will be passed to the slave on the AUX connector which also passes any input
information in a daisy chain to the next Lyngdorf product.
- 13 -
Remote Control
The remote control is used to access the Millennium and
replicate some of the buttons directly accessible on the front
panel. The four buttons used for selecting which device to
control are described below. To control the Millennium the
AMP key should be pressed.
• Amp – Selects the remote for operation with Millennium
or any Lyngdorf amplifier.
• RCS –No function.
• CD - Selects the remote for operation with a Lyngdorf
CD Player.
• Tuner – No function.
• Standby – The standby button toggles the Millennium
between active “On” and standby mode.
• Digital – Changes to Digital input, or if already
selected, cycles to the next Digital input.
• Analog – Changes to Analog input, or if already
selected, cycles to the next Analog input.
• Button 1-8 – Preset 1-7 can be selected with buttons 1-
7, default presets are all linear bypass, and preset
selection of the active preset will only affect the sound
after changing the preset contents with the DSP
software. Button 8 selects bypass.
• UP/DOWN and Channel +/- – Cycles in either Analog
or Digital input.
• Volume Up/down – Changes volume in the chosen
direction
• Mute – Toggles Mute function on/off
Some special functions can be controlled by pressing Info first followed by a numeric key:
• Info+1 – Shows the software version in the display.
• Info+2 – Show the device address in the display.
• Info+3 – Increments device address by one and shows the new address.
• Info+4 – Decrements device address by one and shows the new address.
• Info+5 – Toggles Master/Slave. The display shows -r- for master and -c- for slave.
• Info+6 – Change display light dimmer.
• Info+7 – Toggles baud rate 9600/57600. The display shows either “960“or “576”.
• Info+8 – Changes polarity pos/neg. The display shows -P- for pos. and -n- for neg.
• Info+9 – Stores actual volume as maximum volume level. The display shows either
“on” or “OFF”
The Millennium can act as Master in a set-up with more than one Millennium amplifier. In
this case the remote control is active on the Master Millennium, and disabled on the Slave
Millennium which is operated via the broadcast codes. All information on usage is passed
on to the slave i.e. on/off, volume, mute, preset.
- 14 -
Front panel operations
The operations of the remote control receiver can be bypassed on the front panel for the
Millennium. Bypassing the remote control is done with a long press on the Analog left
selection key “A”. When the remote is turned off the Lyngdorf Logo blinks twice after a 2
sec. press. If the remote functionality is turned on – the Lyngdorf Logo blinks once.
Software
Software and documentation, for both PC and Millennium, can be downloaded from our
The software for PC is:
• Serial Load – used for upgrading the software in Millennium
• AmpCom – used for controlling and setting up Millennium from a PC.
• LYNGDORF DSP – used for making digital filters, crossover and voicing in
Millennium.
These 3 programs come in a zip file called “PC Pack x.x.zip” where x.x is the version
number. In this file are a “setup.exe” and a text file with a release description.
Software or firmware for Millennium comes in a separate file called “Millennium release
xx.zip” where xx is the version number. In this file are a “releasexx.s19” and a text file with
a release description.
- 15 -
Connectors
Mains Connector
Mains voltage to the Millennium is applied via an IEC320 type connector. The supplied
cable with safety ground should be used to connect the Millennium to a mains outlet.
WARNING: Connect the power input only to the AC source printed on the
label. The warranty will not cover any damage caused by connecting to the
wrong type of AC mains.
WARNING: Always disconnect the Millennium from the mains before
changing any connections to its inputs or outputs.
Loudspeaker connectors
The Millennium’s loudspeaker connectors accept bare wire ends up to 5 mm in diameter.
Connect the wires from each loudspeaker to each channel's + and – terminals. Do not
make any other connections to the output terminals. The loudspeaker cable is inserted into
the slot in the loudspeaker terminal, and the terminal is tightened firmly.
WARNING: Always disconnect the Millennium from the mains before
changing any connections to its inputs or outputs.
WARNING: Make sure that no conductive part of the speaker wiring is
accessible. Do not connect loudspeakers with uninsulated terminals.
When the Millennium is operating, there is up to 35V DC on its output terminals with
reference to ground.
Do not connect the output from the amplifier to any other amplifier's output
or any other voltage source. Do not attempt to operate the amplifier in
bridged mono mode.
Cleaning and maintenance
Always unplug the unit from the electrical outlet before cleaning.
This unit does not require any regular maintenance except to keep its exterior clean.
Simply wipe its exterior with a clean soft cloth. A small amount of non-abrasive cleaner
may be used on the cloth to remove any excessive dirt or fingerprints. Do not use abrasive
cleaners or cleaners containing liquid solvents.
- 16 -
Technical specifications
Audio
Parameter
Balanced input connectors
Value
3 pin XLR, gold-plated.
Note
Case=Gnd, Pin1=Gnd,
Pin2=Hot(+), Pin3=Cold(-)
AC-coupled.
Balanced input impedance
10kOhm
Unbalanced input connectors RCA (phono) jack, gold-plated. Case=Gnd, Tip=Hot(+)
Unbalanced input impedance 10kOhm
AC-coupled
DAC Out impedance
75 Ohm
Gain According to volume
control setting. 89 dB = 0 dB
with sensitivity normal and rel.
volume 0 dB
Input sensitivity
Power Supply Variation
Output connectors
4.4V (2.2V with high sens.) 200W/8ohms/89 dB Volume
26dB 65V to 3.3V dep. On Volume
4 insulated binding posts, gold-Will accept bare wire ends of
plated.
2*200W
2*375W
4 Ohms-8 Ohms
up to 5 mm diameter.
1KHz, 0.1% THD+N
1KHz, 0.1% THD+N
It is safe to operate the
amplifier with no load.
-3dB points, 8ohms load.
20Hz-20KHz, 8ohms load
20Hz-20KHz, 4ohms load
20Hz-1KHz
20KHz
A-wgt.
A-wgt.
A-wgt.
Output power, 8ohms
Output power, 4ohms
Nominal load impedance
Frequency response
Frequency response
Frequency response
Output impedance
Output impedance
THD+N, 1W/8ohms
THD+N, 1W/4ohms
THD+N, 100W/8ohms
THD+N, 180W/8ohms
THD+N, 375W/4ohms
S/N ratio
0.3Hz-33KHz
-0dB/+0.2dB
-0.2dB/+0dB
0.035 Ohms
0.4 Ohms
0.015%
0.02%
0.008%
0.01%
0.07%
A-wgt.
A-wgt.
107dB
133 dB
A-wgt. Ref. 200W/8ohms.
A-wgt. Ref. 200W/8ohms.
1KHz, 200W/8ohms.
Dynamic range
Channel separation
Peak output current
Output common mode voltage Max 33V DC
90dB
40A
Ref. Ground. The amplifier can
not be used in bridged mono
mode.
Output DC voltage
5 mV
All audio measurements, except frequency response, are measured with a 20KHz low-
pass filter in accordance with AES-17.
- 17 -
Protection
Parameter
Grounding
Value
Note
Mains earth, chassis and audio
ground are connected
internally.
Output short circuit current
Output DC voltage
Over temperature
40A
5V @ <0.1Hz
All heat sinks and mains-
transformer.
Auto resetting thermal fuse in
mains transformer.
Mains
Parameter
Value
Note
Mains input connector
Mains voltage range
Mains voltage range
Internal mains fuse
Internal mains fuse
Power consumption
Power consumption
Power consumption
Power consumption
IEC 320 cold type
100-120V AC, 50–60Hz
200-240V AC, 50-60Hz
8 Amp / 0.25A
4 Amp / 0.1A
1.5 W
35 W
116 W
820 W
Mains lead supplied.
115V version
230V version
115V version
230V version
STANDBY mode.
OPERATE mode, no output.
2*37.5W/4ohms.
2*300W/4ohms.
Trigger
Parameter
TRIGGER OUT connector
TRIGGER OUT Voltage
Value
3.5mm (1/8") mono jack
12V DC
Note
Case=Gnd, Tip=Input
Short circuit protected
Mechanical
Parameter
Width
Depth
Value
450mm (17.72")
435mm (13.39")
Note
Excluding loudspeaker
connectors (over wheel)
Including loudspeaker
connectors (over wheel.
Excluding feet.
Depth
455mm (14.21")
Height
Height
Net weight
Shipping weight
88.8mm (3.5")
100.6mm (3.96")
18.0Kg (37lb.)
20.0Kg (41lb.)
Including feet.
- 18 -
Trouble Shooting
Protection Mode
A sophisticated monitoring circuit controls the operation of the amplifier. When an error is
detected, the amplifier shuts down into protection mode immediately and indicates the
status by flashing the Lyngdorf logo.
Protection mode can be triggered by:
1. Overload/short-circuit of the speaker outputs (limits current to approx. 35 Amps)
2. DC defected at the speaker outputs; this can be due to extreme program material.
3. Internal power failure burned fuses etc.
4. Mains supply voltage is too low or too high.
5. Overheating of the amplifier.
Most problems are temporary
Most of the above mentioned error conditions are normally temporary. When the
Millennium goes into protection mode, switch off the power and inspect the amplifier.
Check the speaker cables, feel if the cover is very hot. Turn on the amplifier again to see if
normal operation mode may be resumed.
If the error condition persists, the Millennium will return to protection mode immediately. If
this is the case, the Millennium needs authorised service.
NOTE:
• No bridge coupling is possible.
• The frequency response of the Millennium extends down to DC. Playback of material
with extreme infrasonic program material may cause the amp to go into protection
mode in order to protect the speakers.
Future upgrades & features
The Lyngdorf Millennium is a modular design, a platform for state-of-the-art music
reproduction. This means that you can add functions like an analog input Module, a Clock
Gate controlled DVD-player or simply upgrade to future Audio Formats.
That’s the beauty of the Lyngdorf Millennium concept; whatever the future standards will
be, you will easily be able to implement them in your system for a reasonable cost.
This manual will expand together with your Millennium. If you take the time to register your
investment, we guarantee that you will get information about future upgrades and
expansions when they become available.
- 19 -
Support
and newest version of this document.
Technical assistance
If you have any problems with or questions regarding your Lyngdorf Audio product, please
contact your nearest Lyngdorf Audio representative or:
Lyngdorf Audio
Væselvej 114
7800 Skive
Denmark
E-mail: [email protected]
Web-site: www.lyngdorf.com
|