Programmer/Remote
Cat. RZCPG
USER GUIDE
•
•
–
•
1 O
N
O
F
F
2 O
N
O
F
F
3 O
N
O
F
F
F
4 O
N
O
F
Compatible with
TMenabled products!
nload from Www.Somanuals.com. All Manuals Search And Downl
INTRODUCTION
Leviton’s Programmer/Remote, Cat. No. RZCPG, is a
multi-functional device. It uses Z-WaveTM technology
to act as a programmer, zone or scene controller,
remote for setting up and operating your ViziaTM
RF network. This manual will guide you through
the understanding of your RZCPG functions as a
setup controller. Once your network is installed, your
RZCPG may also be used as a wireless controller for
controlling your lighting system.
Your RZCPG comes with batteries.
•
•
–
•
1 O
N
O
F
F
2 O
N
O
F
F
3 O
N
O
F
F
F
4 O
N
O
F
RZCPG
Programmer/Remote
1
nload from Www.Somanuals.com. All Manuals Search And Downl
MENU NAVIGATION and ICONS
Navigating screens and menus on your RZCPG is
accomplished using the following buttons:
LCD
Display
x1
-RZCPG-
(HOME screen
Default Profile
1. Area #1
2. Area #2
3. Area #3
4. Area #4
depicted)
Left
Soft Key
Stand By
Menu
Right
Soft Key
Arrow
Buttons
(up, down,
left, right)
Center
Button
1
2
3
4
ON
ON
ON
ON
OFF
OFF
OFF
OFF
"–"
Button
"+"
Button
From the HOME Screen, pressing buttons 1, 2, 3, 4
will control the areas displayed.
x1
MAIN MENU
1. Device List
2. Who Is...
3. Area
The right soft key
brings
you to the MAIN MENU screen
from the HOME screen and is
used for saving and completing
tasks.
4. Profile
5. Settings
Home
Back
The left soft key
bring you back to the previous screen.
is used to
The up and down arrow buttons allow you
to scroll through each screen and will move the
selection box (
) to each choice.
1. Device List
NOTE: Selections are made on
each screen by pressing the
center button on the RZCPG
unless prompted otherwise.
CENTER BUTTON
2
nload from Www.Somanuals.com. All Manuals Search And Downl
<<
>>
NEw
x1
appears on various
screens as a prompt to create
something new (Area, Profile,
Event, etc.)
AREA
<<
>>
NEW
Back
Home
<
>
ON
x1
Single brackets
designate that more than one
choice is available. Use the left
and right side arrow buttons
to toggle between
All Devices
1. All Devices
<
>
2. ON
3. Default Fade
choices.
Cancel
Save
x1
Check boxes
when multiple selections are
available. Use the and
buttons to select and deselect
from a list.
are used
All Devices
Dimmer #1
Switch #1
Switch #2
selected 1
(
)
3
Back
Who Is
S
Z
x1
PROFILE
<< >>
Radio buttons
are used
when an "either/or" single choice
is available. Scroll the selection
box to your choice and use the
button to select.
NEW
Profile #1
Profile #2
Back
Home
x1
The filter
is used when
you wish to view only checked
devices, or only unchecked
devices from a list. Use the
Area #1
Bedroom
Bathroom
Hall
right arrow button
to toggle
selected 3
between showing devices
checked, unchecked or all (no
filter).
( )
3
Back
Who Is
Leviton also provides various icons that appear on
the screens to provide quick review of the state
of your network, selections made and to assist in
identification of devices (refer to Icon Description
chart).
3
nload from Www.Somanuals.com. All Manuals Search And Downl
ICON DESCRIPTION
Undefined device
Center button
Single choice (radio button) - not chosen
Single choice (radio button) - chosen
Multiple selection (checkbox) - not selected
Multiple selection (checkbox) - selected
Remote Control
Zone/Scene Controller (Single or Multibutton)
Dimmer
Switch
Thermostat
Buzzer OFF (indication)
Buzzer OFF
Buzzer ON
Error Indication
Filter (data on screen is filtered)
Battery Power
STARTUP
Upon initial power up of the RZCPG, the VIZIATMRF
logo will appear briefly. You will then be prompted to
START INSTALLATION CHECKLIST. Press the right
soft key
(YES) to begin Installation Checklist.
x1
INSTALL CHECKLIST
START
by
INSTALLATION
Certified
Z-Wave Compliant
CHECKLIST
NO
YES
4
nload from Www.Somanuals.com. All Manuals Search And Downl
INSTALLATION CHECKLIST
Leviton provides the Installation Checklist as a step
by step tool to setup your ViziaTMRF network and
recommends following these steps in order, specifically
if you are a first time user. System design will impact
performance, so it is necessary to include and update
your devices in a specific order to ensure overall system
performance and reliability. The Installation Checklist
steps are shown below. When a step is completed,
simply press the right soft key
to select NEXT STEP
and the RZCPG will bring you to the next screen.
x1
x1
INSTALL CHECKLIST
INSTALL CHECKLIST
1. Include Dim/Swch
2. Include Controller
3. Update Controller
4. Create Areas
3. Update Controller
4. Create Areas
5. Set Associations
6. Security
5. Set Associations
7. Install Complete
Back
Next Step
Back
Next Step
Using your RZCPG, follow these steps to set up
your ViziaRfTM network:
Include Dimmers/Switches
STEP 1
Pressing the center button
x1
to select Include Dim/Swch
will bring you to the INCLUDE
DIM/SwCH screen and put the
RZCPG into Inclusion Mode.
You will be prompted to press a
button on your Dimmer, Switch or
Plug-In Module. These devices
INCLUDE DIM/SWCH
Press button on
Dimmer/Switch
Cancel
require a simple one step process (button press) to
include into the network (refer to individual device
instruction sheet). Once the button is pressed on
your Dimmer, Switch or Plug-In Module, the RZCPG
will go through a communication process and assign
the node information for that device. The TEXT
EDITOR will display. You can now name your device.
NOTE: The RZCPG is by default assigned #1.
5
nload from Www.Somanuals.com. All Manuals Search And Downl
TEXT EDITOR
Using TEXT EDITOR you can
x1
either assign a name from a list
of templates or assign a unique
name to your device.
TEXT EDITOR
Switch #2
Leviton
Switch #2
NOTE: The right soft key
will
Save? Press
Template
toggle from Template to Abc to
ABC to abc to 123 and back to
Template again. This feature allows you to access
the template names or to select capital/undercase
letters and numerals to name your device.
To use the pre-made Templates,
x1
with Template displayed, use the
up and down arrow buttons
to select a name. The RZCPG
offers a list of over 100 commonly
used names to choose from.
NOTE: The template names are
editable for customization if you
choose to alter them.
TEXT EDITOR
Switch #2
Leviton
Bedroom
Save? Press
Abc
To create a unique name or modify text, under
ABC (or Abc, abc, 123) use the up and down arrow
buttons to change each letter or numeral and
side arrow buttons to navigate. The and
buttons can be used to insert and delete characters.
Once your template or created
name is displayed, press the
x1
INCLUDE DIM/SWCH
Node included!
Node ID# 2:
center button
.Your device
has now been included in
Bedroom
the network with your chosen
name. The RZCPG will confirm
inclusion with the name displayed
and prompt you to continue to
More? Press
Back
Next Step
INCLUDE DIM/SwCH by pressing the center button
or to continue to the NEXT STEP by pressing the
right soft key
.
Include Controller
STEP 2
x1
INSTALL CHECKLIST
NOTE: The INSTALL CHECKLIST
screen will appear with the
selection box around STEP 2
- Include Controller when NEXT
STEP is chosen from STEP 1.
1. Include Dim/Swch
2. Include Controller
3. Update Controller
4. Create Areas
5. Set Associations
Back
Next Step
6
nload from Www.Somanuals.com. All Manuals Search And Downl
Press the center button
on the
x1
RZCPG to bring up the INCLUDE
CNTRLLER screen, where you will
be prompted to place the controller
in program mode.
INCLUDE CNTRLLER
Place controller
in program mode
See Instruction sheet
Begin? Press
Return
NOTE: Leviton Controllers require
an inclusion process that differs
from Dimmers, Switches and Plug-
In Modules. Controllers must be placed into program
mode before they can be included into the network
(refer to individual device instruction sheet).
NOTE: If no controllers are in system, use down arrow
button
to skip to STEP 4.
Once your controller has been placed in program
mode, press the center button
on the RZCPG. The
RZCPG will go through the communication process
and assign the node information for that device. The
TEXT EDITOR will display where you can name your
device (refer to TEXT EDITOR pg. 6).
Once your name is displayed,
x1
press the center button
.The
INCLUDE CNTRLLER
Node included!
Node ID #3:
RZCPG will confirm inclusion
and prompt you to continue to
INCLUDE CONTROLLER by
pressing the center button
to continue to the NEXT STEP
by pressing the right soft key
Room Controller
or
More? Press
Back
Next Step
NOTE: The confirmation process will take some time,
specifically in large networks. Remain close to the
controller until the confirmation is complete.
x1
Update Controller
STEP 3
INSTALL CHECKLIST
NOTE: The INSTALL CHECKLIST
screen will appear with the
selection box around STEP 3
- Update Controller when NEXT
STEP is chosen from STEP 2.
1. Include Dim/Swch
2. Include Controller
3. Update Controller
4. Create Areas
5. Set Associations
Back
Next Step
Press the center button
to
x1
bring up the UPDATE CNTRLS
screen where a list of all the
controllers in the network will be
displayed. With the selection box
around the first controller listed
UPDATE CNTRLS
Room Controller
Hall Controller
(
)
2
Back
Who Is
press the center button
.
7
nload from Www.Somanuals.com. All Manuals Search And Downl
x1
The RZCPG will prompt you to
UPDATE
Please stand within
3 ft from controller
and press YES
to continue
stand within 3 feet of that controller.
Press the right soft key
(YES)
to update your controller. NOTE:
It is important that you remain
within 3 ft. of the controller
you've selected from the list.
If you are unsure about which
controller you are updating
you can use the "who Is"
NO
YES
x1
UPDATE
Node Updated!
Node ID #4
command (see pg. 13).
Room controller
Leviton controllers will blink
during the update process,
confirming you are updating
the correct controller. Update
only one controller at a time.
Return
Once the RZCPG confirms UPDATE it will display
the updated node information. Press left soft
key
(Return). Continue this process until all of
your controllers have been updated. Each time
you successfully update your controller it will be
removed from the list. Once all of your controllers
have been updated, press the right soft key
to
continue to the NEXT STEP.
Create Areas
STEP 4
x1
INSTALL CHECKLIST
NOTE: The INSTALL
1. Include Dim/Swch
2. Include Controller
3. Update Controller
4. Create Areas
CHECKLIST screen will appear
with the selection box around
STEP 4 - Create Areas when
NEXT STEP is chosen from
STEP 2.
5. Set Associations
Back
Next Step
x1
AREA
Press the center button
bring up the AREA screen. With
<< >>
to
<< >>
NEW
NEw
center button
selected press the
to bring up the
CREATE AREA screen. You
can now name your new area
by pressing the center button
(refer to TEXT EDITOR pg. 6).
Once you name your new area,
Back
Next Step
x1
CREATE AREA
Name: Area #1
Add Devices...
press the center button
to
save the information and return
to the CREATE AREA screen.
Cancel
Save
8
nload from Www.Somanuals.com. All Manuals Search And Downl
Scroll to and press the center
button to select Add Devices
which will bring up a list of the
dimmers and switches you
included in Step 1 to add to your
new area. Scroll to each device
x1
AREA #1
Bedroom
Bathroom
Hall
selected 1
check box and use the
and
(
)
3
Back
Who Is
buttons to either add or subtract
each device from your area.
NOTE: You can use the
x1
AREA
<<
4
ON
4 ON button
on the bottom
>>
NEW
Area #1
of the RZCPG to select ALL
devices simultaneously. The 4
OFF
Off button
deselects ALL
Back
Next Step
devices. This feature will work
whenever you encounter check
box lists.
Once you have checked the devices for your area
press the right soft key (Save). The AREA screen
will display with your newly created area and prompt
you to continue to create a new area by pressing the
<<
>>
center button
to the NEXT STEP by pressing the right soft key
to select NEw or to continue
.
1
ON
NOTE: You can use the 1 ON button
and
OFF
1 Off button
on the RZCPG to turn the lights
ON and OFF in an area that has the selection box
around it.
Set Associations
STEP 5
NOTE: The INSTALL CHECKLIST
screen will appear with the
selection box around STEP 5 - Set
Associations when NEXT STEP is
chosen from STEP 4.
NOTE: If no controllers are in
system, use down arrow button
to skip to STEP 6.
x1
INSTALL CHECKLIST
1. Include Dim/Swch
2. Include Controller
3. Update Controller
4. Create Areas
5. Set Associations
Back
Next Step
x1
Press the center button
to bring
ASSOCIATION
Room Controller
Hall Controller
Den Controller
up the ASSOCIATION screen.
A list of controllers included in
Step 2 that support association will
be displayed.
Back
Next Step
Scroll to and press the center
button
to select the controller
you wish to associate an area or areas to.
9
nload from Www.Somanuals.com. All Manuals Search And Downl
The CONTROLLER ASSOC
screen will display with the
selection box around 1. Button
prompting you to select the
button on your controller that
you wish to associate an area to.
x1
CONTROLLER ASSOC
Dev: Room Controller
1. Button 1
<
>
2. Area #1
3. Area ON/OFF
Cancel
Save
Use side arrow buttons
toggle if applicable.
to
Scroll to 2. Area and choose an area you wish to
associate to the button you've selected. This will
allow the button on the chosen controller to control
the desired area.
Selecting 3. Area ON/Off allows you to set an
AREA ON/Off or SCENE command to that button
on your controller (for SCENE commands refer to
Advanced Settings).
Once you are done press the right soft key
(Save) to complete. You will be prompted to
continue setting associations or to proceed to the
NEXT STEP by pressing the right soft key
.
Security
STEP 6
x1
NOTE: The INSTALL
INSTALL CHECKLIST
CHECKLIST screen will appear
with the selection box around
STEP 6 - Security when NEXT
STEP is chosen from STEP 5.
2. Include Controller
3. Update Controller
4. Create Areas
5. Set Associations
6. Security
Press the center button
to
Back
Next Step
bring up the SECURITY screen.
Press the center button
to
x1
select 1. Setup Password.
Enter password using four of the
eight buttons on the RZCPG
SECURITY
1. Setup Password
<
>
2. OPEN
(1 ON, 1 Off, 2 ON, 2 Off etc.)
NOTE: The password you
choose MUST be 4 characters
long.
Back
Save
x1
You will be prompted to, and
must re-enter password.
Scroll to 2. and use the side
SECURITY
1. Setup Password
<
>
2. RZCPG Lock
arrow buttons
to toggle
between choices OPEN, RZCPG
Lock and System Lock.
Back
Save
10
nload from Www.Somanuals.com. All Manuals Search And Downl
Press right soft key
(Save) to complete.
<
>
NOTE: Selecting RZCPG Lock will lock the
RZCPG. When you return to the HOME screen you
will not have access to the MAIN MENU nor any
screens until you press the right soft key
enter your password.
and
<
>
Selecting System Lock will only lock System
Setup, preventing one from changing how the
system is configured until the password is entered
upon prompt.
Install Complete
STEP 7
x1
INSTALL CHECKLIST
NOTE: The INSTALL
3. Update Controller
4. Create Areas
5. Set Associations
6. Security
CHECKLIST screen will appear
with the selection box around
STEP 7 - Install Complete when
you save your security selection.
7. Install Complete
Back
Next Step
Press the center button
to
x1
receive your confirmation that
the INSTALL CHECKLIST is
now complete. Press the center
INSTALL CHECKLIST
Installation Checklist
complete.
button
the RZCPG.
again to start using
Press
to start using RZCPG.
button
The HOME screen of the
RZCPG will be displayed.
x1
-RZCPG-
Default Profile
1. Area #1
2. Area #2
3. Area #3
4. Area #4
Menu
Stand By
11
nload from Www.Somanuals.com. All Manuals Search And Downl
MAIN MENU SCREEN
Pressing the right soft key
while on the HOME
screen will bring up the MAIN MENU screen where
you can navigate through the various selections to
edit or change settings.
x1
x1
MAIN MENU
1. Device List
2. Who Is
MAIN MENU
2. Who Is
3. Area
3. Area
4. Profile
5. Settings
6. System Setup
4. Profile
5. Settings
Home
Home
Back
Back
DEVICE LIST
x1
Selecting 1. Device List from the
MENU screen will bring you to
the DEVICE LIST screen where
a list devices included in the
network will appear. From this
list you can rename devices by
DEVICE LIST
RZCPG
Bedroom
Bathroom
Hall
R
C
Room Controller
(
)
Who Is
Back
8
pressing the center button
to
select a device and using TEXT
EDITOR (pg.6), control ON/OFF and adjust intensity
OFF
levels. NOTE: Pressing the 2 Off button
with
the selection box around a dimming device will
bring up the DEVICE CONTROL menu where you
can use the and buttons to precisely raise
or lower the level with slide control, which will be
displayed at the bottom.
wHO IS
x1
Selecting 2. who Is from the
WHO IS...
Press button on unit
MENU screen will bring you to
the wHO IS... screen where you
can identify your devices. Simply
press a button on a network
included device to obtain the node
information.
After the information is received
by the RZCPG, it will display the
device ID and the NAME assigned
to the device you activated.
Acquiring node info
Back
x1
WHO IS...
This is node #7
Dimmer Scene Cap
RT Slave
Name: Hall dimmer
Press
Back
12
nload from Www.Somanuals.com. All Manuals Search And Downl
AREA
Selecting 3. Area from the MENU screen will bring
you to the AREA screen. You can create a new
area, rename an existing area, modify devices
in an area or delete an area (refer to Step 4 of
INSTALLATION CHECKLIST - Create Areas pg.9).
PROfILE
Selecting 4. Profile from the MENU screen will bring
you to the PROfILE screen. Up to 16 profiles can
be created to control different areas of your house
with your RZCPG. Each device may be controlled by
assigning an area to one of the four buttons on the
RZCPG. NOTE: Default profile will control the first
four areas created with ON/OFF control using the 1
1
ON
4
ON
ON
, 1 Off through 4 ON
,
4 Off buttons respectively.
With the selection box around
x1
PROFILE
<<
>>
NEw press the center
button . You can name your
new profile by pressing the center
button to select Name: (refer
<<
>>
NEW
to TEXT EDITOR pg. 6).
Once you name your new profile,
Back
Home
press the center button
save and scroll to Button. Use
side arrow buttons to
toggle between button choices.
The displayed button will be the
button on your controller that
your profile will react to.
to
x1
NEW PROFILE
Name: Profile #1
Button: 1
Area: Area #1
Action: ON/OFF
Cancel
Save
Scroll to Area and use side arrow
buttons
to choose the area
x1
PROFILE
<< >>
you wish to affect with this profile.
Scroll to Action and use side
arrow buttons
an ON/Off or SCENE (1-255)
command. Scene commands will
also give you a fade option. Use
NEW
Profile #1
Profile #2
Profile #3
to choose
Back
Home
side arrow buttons
to toggle
between fade choices DEfAULT,
IMMEDIATE, or 1 SECOND thru
127 MINUTES.
Press the right soft key
(Save) to complete.
13
nload from Www.Somanuals.com. All Manuals Search And Downl
The HOME screen will display
x1
with your newly created profile.
Use the side arrow buttons
to toggle between profiles when
on the HOME screen. Default
Profile will display when none
-RZCPG-
Default Profile
1. Area #1
2. Area #2
3. Area #3
4. Area #4
Menu
Stand By
are selected. Use the
to deselect a profile.
button
SETTINGS
x1
Selecting 5. Settings from the
MAIN MENU screen will bring
you to the SETTINGS screen.
SETTINGS
1. Contrast
2. Buzzer
3. Security
4. Battery Level
Home
Back
CONTRAST
Sets the contrast for your
RZCPG LCD screen as follows:
x1
CONTRAST
1. Select Contrast.
050 %
2. Use the
and
buttons to adjust
the percentage of contrast.
3. Press right soft key
(Save) to complete.
Save
Cancel
BUZZER
Turns the buzzer on the RZCPG keypad ON or
Off. When the buzzer is ON, a beep will be heard
when pressing the keypad. When the buzzer
is Off, a click will be heard when pressing the
keypad. The default setting is buzzer ON. Adjust the
buzzer as follows:
x1
1. Select Buzzer.
2. Use the side arrow
buttons to turn buzzer ON
or Off.
BUZZER
Buzzer ON
3. Press right soft key
(Save) to complete.
Save
Cancel
14
nload from Www.Somanuals.com. All Manuals Search And Downl
SECURITY
Sets the password and lock level for your RZCPG
or System (refer to INSTALLATION CHECKLIST
- Security pg. 11).
BATTERY LEVEL
Displays the battery level for your
RZCPG as follows:
x1
BATTERY LEVEL
1. Select Battery Level.
-
2.88
+
Back
Home
SYSTEM SETUP
Selecting 7. System Setup
x1
from the MAIN MENU screen
will bring you to the SYSTEM
SETUP screen.
SYSTEM SETUP
1. Install Checklist
2. Advanced
Selecting 1. Install Checklist
brings you to the Installation
Checklist (refer to pg. 5).
NOTE: This feature is not
Back
Home
x1
available on secondary remotes.
ADVANCED
Selecting 2. Advanced will
prompt you to continue with
Advanced Settings. Pressing
Advanced
Settings?
the right soft key
bring you to the ADVANCED
(YES) will
NO
YES
screen.
NOTE: If you are unsure about any of the
following ADVANCED SETTINGS consult
ViziaRf application guide or visit our
website at www.ViziaRf.com.
15
nload from Www.Somanuals.com. All Manuals Search And Downl
NETwORK
Selecting 1. Network from the ADVANCED screen
will bring you to the NETwORK screen.
x1
x1
x1
ADVANCED
NETWORK
1. Include Node
2. Exclude Node
3. Ntwk Rediscovery
4. Update Devices
5. Remove Failed
NETWORK
5. Remove Failed
6. Join Network
7. RZCPG Utils
8. Replace Node
9. Dev Properties
1. Network
2. Association
3. HAI Setup
4. RTS Devices
5. Utilities
Back
Home
Back
Home
Back
Home
1. Include Node
(refer to INSTALLATION CHECKLIST pg. 5)
2. Exclude Node
Use this option to remove a device from the
network (refer to the individual device
instruction sheet for details).
3. Network Rediscovery
This feature is used for updating your network,
specifically if nodes have moved or the network
environment has changed.
It will optimize the mesh
x1
network to ensure overall
system routing integrity.
4. Update Controllers
(refer to INSTALLATION
CHECKLIST - Update
Controllers pg. 8).
NTWK REDISCOVERY
Powerlevel -6DB
To change powerlevel
[
]
press 4 OFF
Start? Press
Back
Home
5. Remove failed
x1
Use this option to detect
devices that are non-
operational and require
removal from the network.
Once the list is generated, you
will press the center button
to select a device to
FAILED NODE
Building Node List
Complete...65%
Cancel
x1
remove. Press the right soft
REMOVE FAILED
key
(YES) to remove the
Bedroom
Bathroom
Hall
device from the network.
6. Join as Secondary
This feature allows you to
join this Leviton RZCPG
Room Controller
Home
Back
16
nload from Www.Somanuals.com. All Manuals Search And Downl
x1
as a secondary remote to
the network. Press the right
REMOVE FAILED
soft key
(YES) after the
Bedroom
Node 2
prompt to continue. NOTE:
This step will erase any
existing data in the remote.
You will then be required to
include this remote with your
primary controller. follow
the controller inclusion/
replication process of
your primary controller
(for RZCPG see pg. 7). This
secondary remote will prompt
you to start building the
node list. Press right soft key
(YES) to complete.
A confirmation (version) screen
will display the same Home ID
as the primary, a new Node
ID, a new serial number and
an x2 designation at the top.
Remove?
YES
NO
x1
JOIN AS SECONDARY
WARNING!
This step will erase
all the data
Continue?
NO
YES
x2
JOIN AS SECONDARY
Would you like
to start building
node list?
NO
YES
NOTE: The secondary remote will be populated
with only the device data of the primary remote
(not Areas, Profiles). You can create new Areas
and Profiles with your secondary remote. If you
wish to duplicate the secondary RZCPG remote
with the primary RZCPG remote's application
information, use RZCPG Utilities.
7. RZCPG Utilities
This feature allows you
x1
to duplicate all necessary
network data from a primary
RZCPG remote into your
secondary RZCPG remotes.
RZCPG UTILS
1. Get Data
2. Send Data
3. Update DB (Man)
4. Update DB (Aut)
1. Get Data is selected from
Back
Home
the receiving RZCPG
remote to retrieve the
selected data (Areas,
Profiles,) from the sending
RZCPG remote.
x1
TX DATA
When prompted
on receiving unit
press one of the
group buttons
2. SEND data is selected
from the primary RZCPG
remote to transfer the
Back
Home
17
nload from Www.Somanuals.com. All Manuals Search And Downl
data. Follow the prompts to
complete this process.
NOTE: Update DB (no. 3
and 4) are only available on
secondary RZCPG remotes.
x1
RX DATA
Setup Data
Areas
Profiles
Select receive items
Start? Press
3. Update DB (Man) is used
Back
Home
to manually perform a
database update (devices in the network, their
names and types) for a secondary remote that
has joined the network. It will require you to
press buttons on each individual device you
wish to update in your secondary remote.
4. Update DB (Aut) is used to perform an
automatic database update (devices in
the network, their names and types) for a
secondary remote that has joined the network.
8. Replace Node
Use this option to replace
non-operational devices in
the network. Once the list is
generated, you will press the
x1
FAILED NODE
Building Node List
Complete...65%
center button
to select
a device to replace. You will
be prompted to prepare the
controller to be replaced or
to press a button on a slave
device to be replaced when
prompted. The button press
will occur after you initiate
the replacement process by
pressing the center button
on the RZCPG. After
Cancel
x1
REPLACE NODE
Bedroom
Bathroom
Hall
Room Controller
Home
Back
replacement you can name the replacing device
(refer to TEXT EDITOR
pg. 6). Once your name is saved, you will receive
confirmation that the node has been replaced.
x1
x1
REPLACE NODE
Node replaced!
Node ID# 8:
REPLACE NODE
Prepare replacing
controller or press
button on slave
when prompted
Garage
Start? Press
More? Press
Back
Next Step
Home
Back
18
nload from Www.Somanuals.com. All Manuals Search And Downl
9. Device Properties
This feature will display information about
a particular device (Name, Node ID and
Description) when selected from the list.
x1
x1
PROPERTIES
RZCPG
PROPERTY
Name: RZCPG
R
C
Bedroom
Hall
Room Controller
NID: 001 Cntrl Room
Portable Remote
Mfg. by Leviton
(
)
4
Back
Home
Back
Home
ASSOCIATION
Selecting 2. Association from
the ADVANCED screen will
bring you to the ASSOCIATION
screen. NOTE: Consult ViziaRf
application guide for advanced
ASSOCIATION options.
x1
ASSOCIATION
Room Controller
Hall Controller
Den Controller
Back
Home
HAI SETUP
Selecting 3. HAI Setup from
the ADVANCED screen will
bring you to the HAI SETUP
screen. This feature allows for
the creation of subscriptions
for devices when setting up a
PC interface (refer to ViziaRf
application guide).
x1
HAI SETUP
Bedroom
Hall
Room Controller
(
)
3
Back
Home
RTS DEVICES
Selecting 4. RTS Devices from
the ADVANCED screen will
bring you to the RTS DEVICES
screen. This is a network
x1
RTS DEVICES
1. Set Routes
2. Set Hail
3. Update Routes
optimization feature which can
enhance performance and
communication ability (refer to
ViziaRf application guide).
Back
Home
19
nload from Www.Somanuals.com. All Manuals Search And Downl
UTILITIES
Selecting 5. Utilities from the ADVANCED screen
will bring you to the UTILITIES screen.
x1
x1
UTILITIES
1. Who Is
2. Version
3. Rediscovery
4. Dev Properties
5. Reset
UTILITIES
3. Rediscovery
4. Device Property
5. Reset
6. Test ZW
7. Test CR
Back
Home
Back
Home
1. who Is...
(refer to wHO Is... pg.13).
2. Version
This feature displays the
ViziaTMRF and Z-WaveTM
versions, the Home ID, Node
ID and Serial No. of your
RZCPG. You can also access
x1
VIZIA RF V1.09
Z-Wave 2.06
Dec 7 2006
HID: 00989680
NID: 1
S/N: 007358DH
Back
this screen by pressing the up arrow button
while on the HOME screen.
3. Rediscovery PL
x1
This feature allows you to
change the power level used for
network rediscovery (refer to
Network Rediscovery pg. 19).
4. Device Properties
(refer to Device Properties
pg. 22).
REDISCOVERY PL
-3 DB
+ – to adjust
/
Cancel
Save
x1
RESET
5. Reset
ALL DATA
WILL BE
LOST
Resets your RZCPG back to
factory default and erases any
programmed information from
the remote. NOTE: Resetting
the RZCPG to factory default
PROCEED?
NO
YES
does not reset your devices. If you want to
factory reset your devices refer to the individual
device instruction sheet for that device.
6. Test Zw
wARNING: for factory use only! DO NOT USE.
7. Test CR
wARNING: for factory use only! DO NOT USE.
20
nload from Www.Somanuals.com. All Manuals Search And Downl
NOTES
nload from Www.Somanuals.com. All Manuals Search And Downl
LIMITED 5 YEAR wARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and
not for the benefit of anyone else that this product at the
time of its sale by Leviton is free of defects in materials
and workmanship under normal and proper use for five
years from the purchase date. Leviton’s only obligation
is to correct such defects by repair or replacement, at
its option, if within such five year period the product is
returned prepaid, with proof of purchase date, and a
description of the problem to Leviton Manufacturing
Co., Inc., Att: Quality Assurance Department, 59-25
Little Neck Parkway, Little Neck, NewYork 11362-2591.
This warranty excludes and there is disclaimed liability
for labor for removal of this product or reinstallation. This
warranty is void if this product is installed improperly or in
an improper environment, overloaded, misused, opened,
abused, or altered in any manner, or is not used under
normal operating conditions or not in accordance with
any labels or instructions. There are no other or implied
warranties of any kind, including merchantability
and fitness for a particular purpose, but if any implied
warranty is required by the applicable jurisdiction,
the duration of any such implied warranty, including
merchantability and fitness for a particular purpose, is
limited to five years. Leviton is not liable for incidental,
indirect, special, orconsequentialdamages, including
without limitation, damage to, or loss of use of, any
equipment, lost sales or profits or delay or failure
to perform this warranty obligation. The remedies
provided herein are the exclusive remedies under this
warranty, whether based on contract, tort or otherwise.
for additional information, contact Leviton’s Techline
at 1-800-824-3005 or visit Leviton’s website at
DI-104-RZCPG-20A-X1
nload from Www.Somanuals.com. All Manuals Search And Downl
This page is NOT to be printed in the booklet
LEVITON INSTRUCTION SHEET/MANUAL
SPECIFICATIONS
DI-104-RZCPG-20A-X1
Black
Helvetica
40 lb. offset
Paper size:
5.75" x 6" (Printer Spread)
Overall size:
5.75" x 3" (booklet - saddle stitch)
Final fold size:
DOCUMENTATION
N/A
LG
12/19/06
6"
Saddle
Stitch
5.75"
2
3
OVERALL SIZE
3"
Cat. No.
5.75"
Booklet
1
nload from Www.Somanuals.FcIoNAmL .SIAZEll Manuals Search And Downl
|