Single Pole (One location) or 3-Way (Multi-location)
Electronic Countdown Timer Switch
Cat. No. LTB15, LTB30, LTB60, LTB02, LTB12 Lighted
20A Resistive/Inductive, 1800W Incandescent, 1HP
120VAC, 60Hz
INSTALLATION INSTRUCTIONS
WARNINGS AND CAUTIONS:
WARNINGS AND CAUTIONS:
•
•
•
To be installed and/or used in accordance with appropriate electrical codes and regulations.
If you are unsure about any part of these instructions, consult an electrician.
•
•
Disconnect power at circuit breaker or fuse when servicing, installing or removing fixture.
Use only one (1) Leviton electronic countdown timer switch in a multi-location circuit with up to 9 coordinating remote switches
without LEDs or up to 4 matching remote switches with LEDs
Maximum wire length from timer switch to all installed remote switches cannot exceed 300 ft (90 m).
Use this device only with copper or copper clad wire only.
Leviton electronic countdown timer switches are not compatible with standard 3-way or 4-way switches. They must be used with compatible
.
Vizia ® ON/OFF remote switches.
•
•
+
•
Recommended minimum wall box depth is 2-1/2”.
PK-93796-10-00-2A
IMPORTANT: For 3-Way applications, note that one of the screw terminals
from the old switch being removed will usually be a different color (Black)
or labeled Common. Tag that wire with electrical tape and identify as the
common (Line or Load) in both the switch wall box and remote wall box.
Step 4a cont'd
Step 4b cont'd
TOOLS NEEDED TO INSTALLYOUR TIMER SWITCH
Timer Switch
Coordinating Remote Switch (no LED) Timer Switch
Slotted/Phillips Screwdriver
Electrical Tape
Cutters
Pliers
Ruler
Pencil
Hot (Black)
WH
BK
WH
BK
Changing the color of your device:
White
GGroruenend Red
Black
Hot (Black)
(unused)
Preparing and connecting wires:
Step 3
Your device may include color options. To change color of the face,
proceed as follows:
Green
Ground
Green
Ground
Pull off pre-cut insulation from timer switch leads. Make sure
that the ends of the wires from the wall box are straight (cut if
necessary). Remove insulation from each wire in the wall box
as shown:
Black
Yellow/Red
RD
RD
YL/RD
YL/RD
(unused)
Line
120VAC, 60Hz
Black
Load
Insulating
Line
Load
Label
120 VAC, 60Hz
Strip Gage
(measure bare
wire here)
5/8"
(1.6 cm)
White
Line up tabs and
press in sides one
at a time to attach
White
Push in side
at tab to release
Neutral (White)
Cut
(if necessary)
Neutral (White)
WIRING TIMER SWITCH:
Connect wires per WIRING DIAGRAM as follows:
MAXIMUM LOAD PER TIMER FOR MULTI-DEVICE INSTALLATIONS
Load Single Two Devices More than 2 devices
Resistive Load 20A (2400W) 16A (1920W) 16A (1920W)
WIRING TIMER SWITCH:
Connect wires per WIRING DIAGRAM as follows:
Green or bare copper wire in wall box to Green lead.
Line Hot wall box wire to Black lead.
Load wall box wire to Red lead.
Line Neutral wall box wire to White lead.
Timer Switch Yellow/Red lead should have Red insulation label affixed.
Proceed to Step 5.
NOTE: The timer switch must be installed in a wall box that has a Line
For non-standard wiring applications, refer to
Wire Nut and Connector Size Chart
Hot connection.
•
•
•
•
•
•
NOTE: Maximum wire length from timer switch to all installed remote
WIRE CONNECTOR / # OF COND. COMBINATION CHART
switches cannot exceed 300 ft (90 m).
Green or bare copper wire in wall box to Green lead.
Incandescent Load
1800W
Inductive Load 20A
Motor Load 1HP
1800W
16A
1800W
16A
1 - #12 w/ 1 to 3 #14, #16 or #18
2 - #12 w/ 1 to 2 #16 or #18
1 - #14 w/ 1 to 4 #16 or #18
2 - #14 w/ 1 to 3 #16 or #18
•
•
Line Hot (common) wall box wire identified (tagged) when removing
old switch to Black lead.
First Traveler wall box wire to Red lead (note wire color).
1HP
1HP
•
•
•
INSTALLINGYOUR TIMER SWITCH
Remove Red insulating label from Yellow/Red lead.
•
Make sure that the ends of the wires from the wall box are
straight (cut if necessary).
Remove insulation from each wire in the wall box as shown.
For Single-Pole Application, go to Step 4a.
For 3-Way Coordinating Remote Switch (no LEDs) Application, go to Step 4b.
For 3-Way Matching Remote Switch (with LEDs) Application, go to Step 4c.
Second Traveler wall box wire to Yellow/Red lead (note wire color).
This traveler from the timer switch must go to the terminal screw on
the remote switch marked "YL/RD".
+
3-Way Wiring with Vizia Coordinating Remote
Switch (no LED) Application:
Step 4b
NOTE: Use check boxes
when Steps are completed.
•
•
•
•
WARNING: TO AVOID FIRE SHOCK OR DEATH;TURN
OFF POWER at circuit breaker or fuse and test that power is
off before wiring!
Step 1
•
Line Neutral wall box wire to White lead.
Coordinating Remote Switch
Timer Switch
+
WIRING VIZIA COORDINATING REMOTE SWITCH:
Connect wires per WIRING DIAGRAM as follows:
NOTE: "BK" and "RD" terminals on coordinating remote switch are
OFF
OFF
OFF
OFF
OFF
OFF
ON OFF
ON OFF
ON OFF
N OFF
OFF
O
ON
ON
ON
ON
ON
ON
Black
Single Pole Wiring Application:
Step 4a
WH
BK
1
2
unused. Tighten both screws.
2
NOTE: Maximum wire length from timer switch to last remote switch
White
1
Black
1
is 300 ft (90 m).
•
•
Identifying your wiring application (most common):
NOTE: If the wiring in your wall box does not resemble any of
these configurations, consult an electrician.
Step 2
3
5
Yellow/Red
Green or bare copper wire in wall box to Green terminal screw.
Load wall box wire identified (tagged) when removing old switch to
5
4
RD
D
YL/R
Red
4
First Traveler (note color as above).
Single Pole
3-Way
White
Red
2
4
Green
3
•
Second Traveler wall box wire (note color as above) to terminal
screw marked "YL/RD". This traveler from the remote switch must go
to the Yellow/Red lead of the timer switch.
Remove White insulating label from terminal screw marked "WH".
Line Neutral wall box wire to terminal screw marked "WH".
Proceed to Step 5.
1. Line (Hot)
2. Neutral
3. Ground
4. Load
1. Line or Load (see
IMPORTANT instruction)
2. Neutral
2
1
2
1
•
•
•
3. Ground
3
4
5
3
4
4. First Traveler – note color
5. Second Traveler – note
color.
3
Green
Yellow/Red
Insulating label:
This wire is used in 3-way installations only.
For single pole installations, do not remove this insulating label.
NOTE: For matching remote w/LEDs installation,
the First Traveler becomes Line Hot.
|