STB-HDM2000
User Manual
Please read carefully before use
InTroDucTIon
Thank you for choosing this quality Set top box from Laser Co Australia.
This device enables you to receive digital free-to-air channels.
TaBle of conTenTS
Front Panel and Rear Panel ................................................................................................................................4
Remote Controller .....................................................................................................................................................5
First time installation ..............................................................................................................................................6
System Setup ................................................................................................................................................................6
Video Setting ................................................................................................................................................................7
Audio Setting ................................................................................................................................................................8
Favourites ........................................................................................................................................................................9
The Menus ......................................................................................................................................................................9
Recording ...................................................................................................................................................................... 10
Trouble Shooting..................................................................................................................................................... 11
3
STB-HDM2000 User Manual
fronT panel anD rear panel
Front Panel
1. MUTE
2. CH+
3. CH-
5. STANDBY INDICATOR
6. REMOTE CONTROL SENSOR
7. USB INPUT
4. LED DISPLAY
Rear Panel
1. Antenna Input
2. Spare Antenna Output
3. Video Output
5. YCbCr Output
6. Coaxial
7. Left/Right Audio Output
8. Super Video Output
4. HDMI Output
4
reMoTe conTroller
1.
2.
3.
4.
STANDBY: Press to place the unit in
standby mode.
NUMBER KEYS:Used to select channel
numbers or input numbers in menus.
TEXT: Used to open teletext OSD display if
teletext available in the broadcast stream.
MENU: Display main menu on TV screen,
press again to exit the menu.
5/23. CH+/CH-: Program changing keys. Move
cursor up or down in menu item.
6/21. VOL-/ VOL+: To increase / decrease volume.
Or to move cursor left or right in menu item.
And to change date in the EPG environment.
7.
8.
9.
OK: Used to confirm a selection
within a menu.
EPG: Used to display information about the
program being viewed and what’s on next.
FAVOURITES: Used to access your
favourite channels.
10.
11.
REC: Press “REC” button to record to USB.
PLAY/PAUSE: Used to play and pause
multimedia files from USB.
12.
13.
STOP: Stop playing USB Media.
PREV/NEXT/REV/FWD: Play previous/next
USB Media image REV/FWD speed up/down.
RED/GREEN/YELLOW/BLUE: Use to
navigate between pages in EPG mode.
USB: Play USB media.
14.
15.
16.
HDMI: Switch the HDMI
576i/576p/720p/1080i.
TV/RADIO: Switch between Digital Radio
and DVB-T modes .
AUDIO: Change the Audio language or
switch to AC3 mode (availability depends
on the channel).
17.
18.
19.
SUB-T: Display subtitle options (availability
depends on the channel).
20.
22.
24.
EXIT: Use this key to quit current menu.
MUTE: Mutes the volume.
INFO: Display information about the
current channel.
25.
RETURN: Go back to the previously
viewed channel.
26/27. PAGE UP/PAGE DOWN:To navigate in the
menu environment.
5
STB-HDM2000 User Manual
fIrST TIMe InSTallaTIon
Start channel installation.
For first time use, the automatic installation message will appear on screen.
a. Select the menu display language.
b. Select the reception country.
c. Then, select your time zone .
d. Please keep the LCN (Logical Channel Number) option ON (activated), so that
the channels can be classified in the correct order.
e. Press the Start button to begin the channel search. The DVB-T channel search
starts immediately and will only take a few minutes
SySTeM SeTup
Press [Menu] key to access:
OSD Language
Use this item to select the language of the setup menu and screen display.
Country
Australia is the correct default setting.
LCN (Logical Channel Number)
Used to classify DVB-T channels in the predefined order. In most of the countries,
including Australia, this option must be enabled.
Time Zone
In this menu adjust the time zone to NSW/ACT+10:00, VIC+10:00, QLD+10:00,
SA+9:30,WA+8:00, TAS+10:00,NT+9:30
Parental Control
Select Parental Control to set a block based on program ratings. Highlight Parental
Control and press OK. A PIN CODE Dialogue box will be displayed, enter your PIN
(default code is “0000”) and press OK. Once in the Parental Control sub-menu use
6
the up and down arrow keys to select the level of program rating to be blocked. All
programs with this rating and above will require the PIN code to view the program.
Change Password
To change your password (PIN Code) follow these simple steps:
1. Highlight Change password and press OK to activate the
Change PIN dialogue box.
2. Enter the current PIN (default is “0000”) and press OK.
3. Enter your new PIN and press OK
4. Enter your new PIN once again then press OK to verify the change.
System Information
Highlight System Information and press OK to view software and hardware tags.
Press Ok to exit this environment. .
Factory Reset
Use this option if you encounter a problem after having changed some parameters.
This option will reset the unit’s data to restore it to the out of factory value, thus
deleting all channels. You will need to scan all Channels Afterwards.
VIDeo SeTTIng
TV System
The default setting for this environment is PAL.
HDMI Output
To enjoy the enhanced audio and video quality that HDMI offers, you need an
HD Ready television with HDMI connection. You then simply need to select the
maximum resolution supported by your television in the menu:
•
•
•
•
576i/480i
576p/480p
1280x720p (720p)
1920x1080i (1080i)
7
STB-HDM2000 User Manual
Display problem in HDMI mode
If you have selected a HDMI resolution which is not supported by your TV (for
example, you have selected 1080i while your TV supports 720p resolution only),
a black screen will appear. To solve this problem, press the HDMI button on the
remote to change the HDMI resolution.
Screen Ratio
In this environment you can select the aspect ratio to match your TV, for a
widescreen TV or panel version 16:9.
auDIo SeTTIng
Audio LR Mode
LR MODE can switch left/Right/Stereo.
Audio SPDIF
Selecting the SPDIF setting allows the user to adjust the audio output on SPDIF
Ports to work in harmony with audio equipment (e.g.receiver,speakers) conected
to this unit.
PCM Select this option when you are going to use stereo signals(2 channels).
RAW If you select this option the player will use the DVB original audio track. Use
this option when you want to use the Dolby Digital AC3 signals through the
coaxial audio output.
8
faVourITeS
This function allows you to define a list of favourite channels. When you select
the menu CHANNEL EDIT, a message will appear to ask you to select whether you
want to create a favourite list for DVB-T channels, or for radio stations.
a. Press the red button to select a favorite list 1,Press the red key a second time
for favorite list 2,and a third Time favorite list 3.
b. Press the UP and DOWN keys to select a channel and press OK to add this
channel to the selected favorite list.A confirmation logo will be displayed next
to the selected channel.
c. Press the EXIT key to quit the menu.
THe MenuS
Main Menu
System Setup
Video Settings
Audio Settings Installation
Channel Edit
Country
Lcn
TimeZone
TV System
HD Output
Screen Ratio
LR Mode
SPDIF
Manual Search
Audio Search
Upgrade STB
OTA
TV Channel
Radio Channel
Parental Control
ChangePassword
System Information
Factory Reset
9
STB-HDM2000 User Manual
recorDIng anD prograM reMInDer
Record live TV
Simply use the “REC” button while viewing the current channel.
Schedule record / Reminder
Highlight your chosen program and press “OK”. Confirm the schedule recording/
reminder settings and press “OK” to confirm.
Notes
•
•
•
Conflicts may occur if 2 or more programs are scheduled for the same time.
Recorded files are designed to play on this unit only.
Recordings are made to a USB flash drive or external hard drive (less than
500GB). Please plug your device in before powering the unit on. Restart the unit
if there are any connection issues.
THe MenuS
10
TrouBle SHooTIng
Symptom
possible cause
remedy
Connect power cord
properly into the power
socket
AC power cord
disconnected
LED on front panel does Incorrect connection of
Connect two terminals
correctly with RCA
not display
the video/audio output
to TV input terminal
Incorrect Connection of
antenna cable
Connect the antenna
cable correctly
Incorrect placement of
antenna
Adjust the direction of
antenna
Check the cable
connections, TV and
other equipment
connected between the
TV and the receiver or
adjust the antenna
No picture or sound
No signal or weak signal
Your TV mode is
different from Set Top
Box broadcasting mode
Use AV mode
Black and white screen
or V-Hold
Battery exhausted
Change the batteries
Switch off the light
Fluorescent light
interfering with the
remote controller
The remote controller is
not working
Unplug the power from
the wall and plug it
back in
No Power
Power Down
11
|