OWNER’S MANUAL
Magic Remote
Please read this manual carefully before operating your set and retain it
for future reference.
AN-MR400
Remote control (AN-MR400G)
RF Dongle (AN-MR400D)
(Brazil : www.lge.com)
3
* To avoid wireless interference, keep the distance
between the Wi-Fi dongle and the remote RF
RF DONGLE
dongle over 20 cm.
LA97**/ LA96**/ LA88**/ LA86**/ LA79**/
LA74**/ LA71**/ LA69**/ LA68**/
LA66**(LA6600 Except for Korea) /
LA64**(Japan, Asia, Austrailia, Middle East, Africa)
/ LA6250(Korea) / LA6205(Brazil, Mexico,
USA, Canada) / LA620*(Japan, Asia, Austrailia
, Middle East, Africa) / LN6100(Middle East,
Africa) / LN5750(Brazil, Mexico, USA, Canada),
LN570*(Korea, Except for 32LN570*)/
LN570*(Middle East, Africa)/ LN578*(Europe)/
PH67**/ PH66** / PH47** models do not require RF
dongle connection. RF Dongle is built in TV.
Cable IN
RF SPECIFICATION
The Magic Remote Control communicates with
the RF Dongle using Bluetooth Version 3.0 .
REV.5
ꔛ
ꔛ
Output Power (Max.) : 10 dBm or lower
Lamp
Maximum Communication Distance :
Line of Open Sight approx. 10 m
INSTALLING THE RF DONGLE
Image shown may differ from your TV.
ꔛ
ꔛ
Frequency Range :
2.400 GHz - 2.4835 GHz
1 Locate the designated Velcro attachment
location on the TV. Then tear off the protection
paper and attach the Velcro. (The attachment
location is different depending on the TV model
you own)
Data Rate (Max.) : 3 Mbps
2 Connect the RF Dongle Cable plug on the RF
Dongle to a USB or USB Apps jack on the TV.
PRECAUTIONS TO TAKE
ꔛ
ꔛ
ꔛ
Use the remote control within the specified
range (within 10 m).
You may experience communication failures
when using the device outside the coverage area
or if there are obstacles within the coverage
area.
Velcro
You may experience communication failures
depending on the accessories.
Devices such as a microwave oven and wireless
LAN operate in the same frequency band (2.4
GHz) as the Magic Remote Control. This may
cause communication failures.
*Attach the RF Dongle aligning with the upper left
corner bracket.
3 Attach the RF Dongle to the velcro as shown
above and then turn on the TV.
The Magic Remote Control may not work
properly if a wireless router (AP) is within 1
meter of the TV. Your wireless router should be
more than 1 m away from the TV.
4 Turn your TV on and wait 20 seconds. Now,
register the Magic Remote Control with your TV.
* If the RF Dongle for the wireless media box is
attached, attach the RF Dongle for the Magic
Remote Control on the below right of the back of
the TV.
ꔛ
ꔛ
Do not disassemble or heat the battery.
Do not drop the battery. Avoid avoid extreme
shocks to the battery.
ꔛ
Inserting the battery the wrong way may result in
explosion.
4
REGISTERING
HOW TO USE
To use the Magic Remote Control, pair it with
your TV first.
How to register the Magic
Remote Control
1 Put batteries into the Magic Remote
Control and turn the TV on.
2 Point the Magic Remote Control at
your TV and press the WHEEL (OK)
on the remote control.
* If the TV fails to register the Magic
Remote Control, try again after
turning the TV off and back on.
How to Re-register the Magic
Remote Control
Press the BACK and SMART
at
the same time, for five seconds, to
unpair the Magic Remote Control
with your TV.
If you wish to re-register the remote,
press the WHEEL (OK) on the remote
control.
VPDUW
* Shake the Magic Remote Control slightly to the right
and left or press SMART , , /Q.MENU buttons to make
the pointer appear on the screen.
* Shake the Magic Remote Control slightly to the right
and left to make the pointer appear on the center of
screen.
* If the pointer has not been used for a certain period of
time, it will disappear.
* The wheel also functions as the ‘OK’ button when
pressed.
* You can change channels and scroll through menus
using the Wheel.
* You can just move your wrist to move the pointer
instead of moving your whole arm.
* The Magic Remote Control depletes batteries faster
than a normal remote due to the additional features.
You may wish to use rechargeable batteries.
* If the pointer loses its calibration, set down the remote
for a couple of minutes to let it recalibrate.
|