User’s Guide
L2000CP
Make sure to read the Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for furture reference.
See the label attached on the product and give the information to your
dealer when you ask for service.
Safety Precautions
Keep the packing anti-moisture material or vinyl packing out of the reach of children.
- Anti-moisture material is harmful if swallowed. If swallowed by mistake, force the patient to vomit and visit the
nearest hospital. Additionally, vinyl packing can cause suffocation. Keep it out of the reach of children.
Do not put heavy objects on the product on sit upon it.
- If the product collapses or is dropped, you may be injured. Children must pay particular attention.
Do not leave the power or signal cable when someone can trip over it.
- The passerby can falter, which can cause electrical shock, fire, product breakdown or injury.
Install the product in a neat and dry place. Do not use near water.
- Dust or moisture can cause electrical shock, fire or product damage.
Do not add accessory that have not been designed for this display.
If you smell smoke or other odors or hear a strange sound from the product unplug the power cord and
contact the service center.
- If you continue to use without taking proper measures, electrical shock or fire can occur.
If you dropped the product or the case is broken, turn off the product and unplug the power cord.
- If you continue to use without taking proper measures, electrical shock or fire can occur. Contact the service center.
Do not drop an object on or apply impact to the product. Do not throw any toys or objects at the product.
- It can cause injury to humans, problems to the product and damage the display.
Keep out of reach of children and do not place toys near the product.
Make sure the product ventilation hole is not blocked. Install the product more than 10cm from the wall.
- If you install the product too close to the wall, it may be deformed or fire can break out due to internal heat build-up.
Do not cover the product with cloth or other material (eg. plastic) while plugged in.
- The product can be deformed or fire can break out due to internal overheating inside the product.
Place the product on a flat and stable surface that is large enough to support the product.
- If the product is dropped, you may be injured or the product may be broken.
Install the product where no Electromagnetic Interference occurs.
Keep the product away from direct sunlight.
- The product can be damaged.
Do not place the product on the floor.
- Small Children and others may trip over it.
Precautions in Moving the Product
Warning
Make sure to turn off the product.
- You may be electrocuted or the product can be damaged.
Make sure to remove all cables before moving the product.
- You may be electrocuted or the product can be damaged.
When lifting or moving the product, do not hold it upside down while holding only the stand.
- This may cause the product to fall resulting in damage or injury.
Do not shock the product when moving it.
- You may be electrocuted or the product can be damaged.
Make sure the panel faces forward and hold it with both hands to move.
- If you drop the product, the damaged product can cause electric shock or fire. Contact an authorized the
service center for repair.
Do not place the product face down.
- This may damage the TFT-LCD screen.
2
Safety Precautions
Precautions in Using/Cleaning the Product
Warning
Do not attempt to disassemble, repair or modify the product yourself.
- Fire or electric shock can occur.
- Contact the service center for repair.
When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent
scratching. Do not clean with a wet cloth. Or spray water or other liquids directly onto the product.
An electric shock may occur. (Do not use chemicals such as benzene, paint thinners or alcohol)
Keep the product away from water.
- Fire or electric shock accident can occur.
Do not put or store flammable substances near the product.
- There is a danger of explosion or fire.
Keep the product clean at all times.
Take a comfortable and natural position when working with a product to relax the muscles.
Take a regular break when working with a product for a long time.
Do not press on the panel with a hand or sharp object such as nail, pencil or pen, or make a scratch on it.
Keep proper distance from the product and rest from time-to-time.
- Your vision may be impaired if you look at the product too closely or fpr too long.
Set the appropriate resolution by referring to the User’s Guide.
- Your vision can be impaired.
Keep small accessories out of the reach of children.
Leaving a fixed image on the screen for a long time may cause damage to the screen and cause image
burn-in. Make sure to use a screen saver on the product. Burn-in and related problems are not covered
by the warranty on this product.
On Disposal
The fluorescent lamp used in this product contains a small amount of mercury.
Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of your local authority.
3
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Connecting the stand base or Removing the stand base
1
.
2.
Place the monitor with its front facing downward on a cushion or soft cloth.
Align the hooks on the stand body with the matching slots in the base of the monitor.
Insert the hooks into slots.
3.
Warning: The tape and locking pin m ay only be re m ove d from thos e m onitors
equipped with a standing base when the base is pulled up.
Otherwise, you may be injured by the protruding sections of the stand.
Hook
Slot
4. Use a coin on the back of the stand base and turn the screw clockwise to tighten.
5. When you desire to detach the monitor from the stand base, use a coin to turn the
screw counterclockwise.
Screw
Important
This illustration depicts the general model of connection. Your monitor may differ from
the items shown in the picture.
Once you connect the stand base, try not to disconnect it.
Do not carry the product upside down holding only the stand base. The product may
fall and get damaged or cause injury your foot.
4
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Positioning your display
1. Adjust the position of the panel in various ways for maximum comfort.
Tilt Range : -5˚~25˚
Swivel :350˚
Height Range : maximun 3.15 inch (80.0mm)
80.0mm
First, remove
the locking pin.
Landscape & Portrait : You can rotate the panel 90o clockwise.
(* For detailed information, please refer to the Pivot Sofeware CD provided.)
* Make sure not to touch the
floor when the head rotates
to use the Pivot function.
Ergonomic
It is recommended that in order to maintain an ergonomic and comfortable viewing
position, the forward tilt angle of the monitor should not exceed 5 degrees.
5
Connecting the Display
Using the Computer
1. Place the monitor in a convenient, well-ventilated location near your computer.
To adjust height of your monitor, unlock the stand lock on top of the stand.
2. Connect the signal cable. When attached, tighten the thumbscrews to secure the
connection.
1
3. Connect the power cord into a proper power outlet that is easily accessible and close
to the display.
2
Power Cord
Signal Cable
Digital signal Analog signal
DVI D-sub
Varies according to model.
Wall-outlet type
NOTE
This is a simplified representation of the rear view.
This rear view represents a general model; your
display may differ from the view as shown.
2
User must use shielded signal interface cables (D-
sub 15 pin cable, DVI cable) with ferrite cores to
maintain standard compliance for the product.
1
PC
PC
MAC
Mac adapter
For Apple Macintosh use, a separate plug adapter is needed
to change the 15 pin high density (3 row) D-sub VGA
connector on the supplied cable to a 15 pin 2 row connector.
4. Press
button on the front switch panel to turn the power
on. When monitor power is turned on, the 'Self Image
Se tting Function' is executed automatically.
(Only Analog Mode)
NOTE
‘ Self Image Setting Function’? This function provides the user with optimal display settings.When
the user connects the monitor for the first time, this function automatically adjusts the display to
optimal settings for individual input signals.
‘AUTO/SET’ Function? When you encounter problems such as blurry screen, blurred letters, screen
flicker or tilted screen while using the device or after changing screen resolution, press the
AUTO/SET function button to improve resolution.
6
Control Panel Functions
Front Panel Controls
Control
Function
MENU Button
Use this button to enter or exit the On Screen Display.
OSD LOCKED/UNLOCKED
This function allows you to lock the current control
settings, so that they cannot be inadvertently changed.
Press and hold the MENU button for several seconds.
The message "OSD LOCKED" should appear.
You can unlock the OSD controls at any time by pushing
the MENU button for several seconds. The message
"OSD UNLOCKED" should appear.
Use these buttons to select or adjust functions in the On
Screen Display.
+
-
Buttons
For more information, refer to page 14.
Use this button to make D-Sub or DVI connector active.
This feature is used when two computers are connected
to the display. The default setting is D-Sub.
(SOURCE Hot key)
7
Control Panel Functions
Control
Function
Use this button to enter a selection in the On Screen
Display.
AUTO/SET
Button
AUTO IMAGE ADJUSTMENT
When adjusting your display settings, always press
the AUTO/SET button before entering the On Screen
Display(OSD). This will automatically adjust your
display image to the ideal settings for the current
screen resolution size (display mode).
The best display mode is
1600 x 1200
Power Button
Use this button to turn the display on or off.
This Indicator lights up blue when the display
operates normally(On Mode). If the display is in Sleep
Mode (Energy Saving), this indicator color changes
to amber.
Power Indicator
8
On Screen Display (OSD) Control Adjustment
Screen Adjustment
Making adjustments to the image size, position and operating parameters of
the display is quick and easy with the On Screen Display Control system. A
short example is given below to familiarize you with the use of the controls.
The following section is an outline of the available adjustments and selections
you can make using the OSD.
NOTE
Allow the display to stabilize for at least 30 minutes before making image adjustments.
To make adjustments in the On Screen Display, follow these steps:
Press the MENU Button, then the main menu of the OSD appears.
+
To access a control, use the
becomes highlighted, press the AUTO/SET Button.
or Buttons. When the icon you want
-
Use the Buttons to adjust the image to the desired level. Use the
-
/
+
AUTO/SET Button to select other sub-menu items.
Push the MENU Button once to return to the main menu to select another
function. Push the MENU Button twice to exit from the OSD.
9
On Screen Display(OSD) Selection and Adjustment
The following table indicates all the On Screen Display control, adjustment,
and setting menus.
Main menu
Sub-menu
BRIGHTNESS
CONTRAST
GAMMA
A
D
Reference
PICTURE
To adjust the brightness,
contrast and gamma of the
screen
sRGB
COLOR
To customize the color of
the screen
PRESET
6500K
9300K
RED
GREEN
BLUE
HORIZONTAL
To adjust the position of the
screen
POSITION
VERTICAL
CLOCK
To improve the clarity and
stability, sharpness of the
screen
PHASE
TRACKING
SHARPNESS
LANGUAGE
To customize the screen
status for a user's operating
environment
SETUP
OSD
HORIZONTAL
POSITION VERTICAL
WHITE BALANCE
POWER INDICATOR
FACTORY RESET
MOVIE / TEXT
FLATRON
To select or customize
desired image settings
F-ENGINE (-)
USER
NORMAL
: Adjustable
A : Analog Input
D : Digital Input
NOTE
The order of icons may differ depending on the model (10~14).
10
On Screen Display(OSD) Selection and Adjustment
You were introduced to the procedure of selecting and adjusting an item
using the OSD system. Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
Press the MENU Button, then the main menu of the OSD appears.
P I C T U R E
Menu Name
Sub-menus
Icons
Button Tip
MENU
: Exit
: Adjust (Decrease/Increase)
: Enter
+
-
SET
: Select another sub-menu
NOTE
OSD (On Screen Display) menu languages on the monitor may differ from the manual.
11
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
PICTURE
P I C T U R E
BRIGHTNESS
To adjust the brightness of the screen.
To adjust the contrast of the screen.
CONTRAST
GAMMA
Set your own gamma value. : -50/0/50
On the monitor, high gamma values
display whitish images and low gamma
values display high contrast images.
MENU : Exit
: Decrease
-
+
: Increase
SET : Select another sub-menu
COLOR
C O L O R
• sRGB: Set the screen color to fit the sRGB
standard color specification.
PRESET
• 6500K: Slightly reddish white.
• 9300K: Slightly bluish white.
Set your own red color levels.
Set your own green color levels.
Set your own blue color levels.
RED
GREEN
BLUE
MENU : Exit
: Decrease
-
+
: Increase
SET : Select another sub-menu
POSITION
P O S I T I O N
HORIZONTAL
To move image left and right.
To move image up and down.
VERTICAL
MENU : Exit
: Decrease
-
+
: Increase
SET : Select another sub-menu
12
On Screen Display(OSD) Selection and Adjustment
Main menu
Sub menu
Description
TRACKING
T R A C K I N G
CLOCK
To minimize any vertical bars or stripes
visible on the screen background.The
horizontal screen size will also change.
PHASE
To adjust the focus of the display. This
item allows you to remove any
horizontal noise and clear or sharpen
the image of characters.
MENU : Exit
SHARPNESS To adjust the clearness of the screen.
: Decrease
-
+
: Increase
SET : Select another sub-menu
SETUP
To choose the language in which the
control names are displayed.
LANGUAGE
S E T U P
OSD
POSITION
To adjust position of the OSD window
on the screen.
If the output of the video card is different
the required specifications, the color level
may deteriorate due to video signal
distortion. Using this function, the signal
level is adjusted to fit into the standard
output level of the video card in order to
provide the optimal image.
WHITE
BALANCE
-
+
M E N U
S E T U P
SET
Activate this function when white and
black colors are present in the screen.
-
+
M E N U
SET
Use this function to set the power indicator
on the front side of the monitor to ON or
OFF.
POWER
INDICATOR
MENU : Exit
: Adjust
-
+
: Adjust
SET : Select another sub-menu
If you set OFF, it will go off.
If you set ON at any time, the power
indicator will automatically be turned on.
Restore all factory default settings except
FACTORY
RESET
"LANGUAGE."
Press the
button to reset immediately.
If this does not improve the screen image, restore the factory default settings.
If necessary, perform the white balance function again. This function will be enabled only when
the input signal is an analog signal.
13
On Screen Display(OSD) Selection and Adjustment
A A A
The OSD screen will appear when you touch the
side of the monitor.
(-) button on the right
Menu Name
Icons
Sub-menu Name
FLATRON F-ENGINE
Screen when applied Screen when not applied
When you execute F-ENGINE, two tones will appear
on the screen as shown. The applied screen will
appear on the left side, whereas the non-applied
screen will appear on the right side.Touch the SET
button to use the adjusted screen.
Main menu
Sub menu
Description
MOVIE This feature lets you easily select the best desired
TEXT image condition optimized to the environment
(ambient illumination, image types etc).
MOVIE: For animation images in videos or movies
MENU : Exit
: Move
SET : Select
TEXT: For text images (Word processing etc.)
,
+
-
USER User
You can manually adjust brightness, ACE or RCM.
You can save or restore the adjusted value even
when using a different environment setting.
To adjust the USER sub-menu function,
Press the SET Button
...
(Brightness): Adjusts screen brightness.
ACE(Adaptive Clarity Enhancer): Selects the clarity mode.
...
U S E R
...
RCM(Real Color Management): Selects the color mode.
BRIGHTNESS
0
Not applied
ACE
RCM
1
1
2
Green enhance
Flesh tone
2
3
Color Enhance
SAVE
M E N U
SET
SAVE
Select the
sub-menu using the SET button
MENU : Exit
and save the YES value using the buttons.
: Decrease
-
: Increase
SET : Select another sub-menu
+
NORMAL This is under normal operating conditions.
14
Troubleshooting
Check the following before calling for service.
No image appears
Is the power cord of
the display connected?
Check and see if the power cord is connected
properly to the power outlet.
Is the power indicator
light on?
Press the Power button.
Is the power on and
the power indicator
blue or green?
Adjust the brightness and the contrast.
Is the power indicator
amber?
If the display is in power saving mode, try moving
the mouse or pressing any key on the keyboard
to bring up the screen.
Try to turn on the PC.
This message appears when the signal from the
PC (video card) is out of horizontal or vertical
frequency range of the display. See the
'Specifications' section of this manual and
configure your display again.
Do you see an "OUT
OF RANGE" message
on the screen?
Do you see a "CHECK
SIGNAL CABLE"
message on the
screen?
This message appears when the signal cable
between your PC and your display is not
connected. Check the signal cable and try again.
Do you see a "OSD LOCKED" message on the screen?
Do you see “OSD
LOCKED” when you
push MENU button?
You can secure the current control settings,
so that they cannot be inadvertently
changed. You can unlock the OSD controls
at any time by pushing the MENU button for
several seconds: the message
“OSD UNLOCKED” will appear.
15
Troubleshooting
Display image is incorrect
Display Position is
incorrect.
Press the AUTO/SET button to automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, adjust the image
position using the H position and V position
icon in the on screen display.
Check Control Panel --> Display --> Settings
and see if the frequency or the resolution were
changed. If yes, readjust the video card to the
recommend resolution.
On the screen
background, vertical
bars or stripes are
visible.
Press the AUTO/SET button to automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, decrease the
vertical bars or stripes using the CLOCK icon in
the on screen display.
Any horizontal noise
appearing in any
image or characters
are not clearly
Press the AUTO/SET button to automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, decrease the
horizontal bars using the PHASE icon in the on
screen display.
portrayed.
Check Control Panel --> Display --> Settings
and adjust the display to the recommended
resolution or adjust the display image to the ideal
setting. Set the color setting higher than 24 bits
(true color).
The screen color is
mono or abnormal.
Check if the signal cable is properly connected
and use a screwdriver to fasten if necessary.
Make sure the video card is properly inserted in
the slot.
Set the color setting higher than 24 bits (true
color) at Control Panel - Settings.
The screen blinks.
Check if the screen is set to interlace mode and if
yes, change it to the recommend resolution.
16
Troubleshooting
Have you installed the display driver?
Have you installed the
display driver?
Be sure to install the display driver from the
display driver CD (or diskette) that comes with
your display. Or, you can also download the
Do you see an
Make sure to check if the video card supports
Plug&Play function.
"Unrecognized monitor,
Plug&Play (VESA DDC)
monitor found"
message?
17
Specifications
20.1 inches (51.0cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
Display
Visible diagonal size: 51.0cm
0.255mm pixel pitch
Horizontal Freq.
Vertical Freq.
Input Form
28 - 83kHz (Automatic)
56 - 85Hz (Automatic)
Sync Input
Video Input
Separate Sync
Composite Sync
SOG (Sync On Green) , Digital
Signal Input
Input Form
15 pin D-Sub Connector
DVI - D connector (Digital)
RGB Analog (0.7Vp-p / 75ohm) , Digital
Max
Recommend
VESA 1600 x 1200@60Hz
VESA 1600 x 1200@60Hz
Resolution
Plug&Play
DDC 2B
On Mode
Sleep Mode
Off Mode
:
≤
≤
58W
1W
1W
Power
Consumption
Width
Height
44.60 cm / 17.56 inches
Dimensions
&Weight
(with tilt/ swivel
stand)
44.78 cm / 17.62 inches (Min)
52.78 cm / 20.76 inches (Max)
24.26 cm / 9.55 inches
Depth
Net
7.6 kg
Tilt
-5˚~25˚
350˚
80mm / 3.15 inches
90˚clockwise
Range
Swivel
Height
Rotate
Power Input
AC 100-240V~ 50/60Hz 1.2A
Operating Conditions
Environmental
Conditions
Temperature 10˚C to 35 ˚C
Humidity
10 % to 80 % non-Condensing
Storage Conditions
Temperature -20˚C to 60 ˚C
Humidity 5 % to 90 % non-Condensing
Tilt/Swivel Stand
Power cord
Attached( ), Detached ( O )
Wall-outlet type or PC-outlet type
NOTE
Information in this document is subject to change without notice.
18
Specifications
Preset Modes (Resolution)
Vertical Freq. (Hz)
Display Modes (Resolution)
Horizontal Freq. (kHz)
1
2
3
4
5
6
7
8
9
31.47
31.47
37.50
43.27
31.47
37.88
46.88
53.67
49.72
48.36
60.02
68.68
68.68
61.80
63.98
79.98
75.00
73.53
640 x 350
640 x 480
640 x 480
640 x 480
720 x 400
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
1152 x 870
1152 x 900
1280 x 1024
1280 x 1024
1600 x 1200
1600 x 1200
70
60
75
85
70
60
75
85
75
60
75
85
75
65.96
60.02
75.02
60
10
11
12
13
14
15
16
*17
**18
60
*Recommend Mode
**Digital Mode
Indicator
MODE
LED Color
On Mode
Sleep Mode
Off Mode
Blue
Amber
Off
19
How to Install the VESA Standard wall mounting
This monitor meets VESA-compliant mounting interface pad
specifications.
VESA wall mounting
Connected to another object (stand type and wall-
mounted type. This monitor accepts a VESA-
compliant mounting interface pad.- optional)
For further information, refer to the VESA Wall
Mounting Instruction Guide.
Kensington Security Slot- optional
Connected to a locking
cable that can be purchased
separately at most
computer stores
20
Digitally yours
|