Operating Instructions
Electric fire KH 1117
ꢀ
Safety information
ƽ Risk of injury or burning
• Never insert objects or body parts such as fingers
inside the chimney through the iron rods.
• Never allow children to use the chimney without the
supervision of an adult. Explain to children the dan-
gers of the appliance.
ƽ Danger of electrocution!
• Connect the appliance only to a 50 Hz grounded
power socket with mains voltage of 230 V~ and that
has been installed according to instructions.
• Do not bend or squeeze the power cord.
• To disconnect, always pull out the plug at the power
socket, do not pull on the power cord.
• The chimney heats up when in operation. Therefore,
never carry it when hot and do so only by the handle
provided for this purpose
• Never touch the chimney, power cord and power plug
with wet hands.
• Lay the power cord such that no one treads or trips
over it.
• Do not use extension cables.
• Do not wind the power cord around the casing of the
chimney.
Intended Use
• Unplug your chimney immediately after use. The
power plug is completely free of power supply only
when you pull it out of the power socket.
• Do not immerse the chimney in liquids under any
circumstances and do not allow any liquids to enter
the device casing of the chimney. Do not expose the
appliance to humidity and do not use it outdoors.
There exists the danger of electrocution. However, if
liquid does enter the device casing, pull out the plug
of the appliance from the power socket and have it
repaired by a qualified technician.
The chimney is used for decorating ad heating living
rooms.
This chimney is exclusively meant for household use
and may be used only for this purpose. Observance of
all the information in these operating instructions, espe-
cially the safety instructions is also from this point of
view.
This chimney is not intended for commercial or industri-
al use.
• Never us the chimney in proximity of water or in
damp cellar areas. The proximity to water presents a
danger, even if the chimney is switched off.
• In case of a breakdown and before cleaning the
chimney, pull out the power plug from power socket.
• If the power cord is damaged, have the chimney
repaired by a qualified technician, before you use it
again.
Description of the appliance
➂ Function switch
➂ Thermostat
➂ Flame regulator
➂ Screws of the glass top
➂ Glowing embers
• Do not operate the chimney, if it has fallen down or is
damaged. Have the appliance checked or repaired by
qualified technicians.
Technical Data
• Do not open or repair the device casing of the chim-
ney. In such cases, safety shall not be guaranteed
and the warranty shall expire. Allow only authorised
technicians to repair the defects in the chimney.
Rated voltage: ..........................................230 V / ~50 Hz
Power rating: ..........................................Max. 1850 Watt
Light bulb : ..................2 candle bulbs, E-14, max. 25 W
ƽ Fire hazard!
• Never place the chimney close to inflammable materi-
als, liquids or gases. Leave at least a one meter
space on all sides and on the top. Never place the
chimney directly under a wall socket.
Before the First Use
Before starting up the appliance, make certain that ...
➂ the appliance or the accessories are in perfect condi-
tion,
• Do not cover the appliance when in operation. Clean
it at regular intervals.
➂ all the packing material has been removed.
• Never leave the chimney unsupervised when in
operation.
• Always place the chimney on an even base.
Otherwise, the chimney could tip over and lead to a
fire.
• Never place the chimney close to heat sources, and
protect the power cord from damages. Therefore, do
not keep the power cord lying in front of the chimney.
• Do not use the chimney with a time switch or a simi-
lar appliance. In case of auto-start, there exists a fire
hazard if the chimney is covered or has been set up
incorrectly.
5
ꢀ
Operation
Cleaning
The chimney is operated by means of three switches:
ƽ Danger of life-threatening electric shock:
• Before you clean the chimney, pull out the plug
from the power socket,
Function switch:
You can set the basic functions with the Function
switch.
➂ Turn the Function switch ➂ step by step for
the following settings:
• and let it cool down completely.
• Never immerse the chimney in water or other
liquids for cleaning
➂ Clean the casing with a damp cloth.
➂ Clean the glass plates with a glass cleaner.
Position
0
Setting
OFF
Do not use cleansers or solvents. They can damage
the plastic surfaces.
only flames
Ventilator without heating
low heat emission (900 W)
maximum heat emission (1850 W)
Disposal
Never dispose off the appliance with normal household
waste.
Thermostat:
If you have selected a setting with heat emission
through the Function switch ➂ you can control the
room temperature with the thermostat ➂.
Enquire with your local town council or regional
authority about the appropriate method of environment-
friendly disposal.
➂ Turn the Thermostat ➂ to the "max“ position.
As soon as the desire room temperature is reached...
➂ Turn the Thermostat ➂ back till you hear an audible
click.
The in-built thermostat now ensures a constant room
temperature.
Warranty & customer service
The warranty conditions and service centre address
can be found in the enclosed warranty slip.
Flame regulator
With the Flame regulator ➂ you can regulate the
flame to any size.
➂ Turn the Flame regulator ➂ in the clock-wise
direction until the desired flame size is obtained.
Replacing the bulbs
ƽ Danger of life-threatening electric shock:
• Before you replace the bulbs, pull out the plug
from the power socket,
• and let it cool down completely.
• Only use candle bulbs with an E-14 thread and
max. 25 Watt
➂ Loosen both the screws ➂ with a slotted screwdriver.
➂ Carefully lift the glass top forward and put it down
safely.
➂ Take out the glowing embers ➂ by pressing with both
the hands and taking it forward.
➂ Now replace the bulbs.
➂ Reassemble the chimney in reverse order and fix the
glass plate with the screws.
6
Kompernaß Handelsgesellschaft mbH · Burgstraße 21 · D-44867 Bochum
ID-Nr.: KH1117-06/04 - V2
|