Kodak Projector 7010 User Manual
KODAK EKTAPRO  
7010/7020/9010/9020  
Slide Projector  
SUPPLEMENT TO THE MANUAL  
©Eastman Kodak Company, 2000  
 
Comments  
Presentations with KODAK EKTAPRO 7010,  
7020, 9010 and 9020 Slide Projectors  
One of the important new features of the KODAK EKTAPRO  
7010, 7020, 9010 and 9020 Slide Projectors is the integrated  
dissolver for a 2-projector dissolve.  
You just have to link two projectors using the KODAK  
Dissolve Cable (accessory) and you can immediately run  
more interesting and lively live presentations using the  
infrared remote control. It is also possible to play automatic  
slide shows with a fixed dissolve time. However, it is not  
possible to record the IR-commands.  
• Even when the two projectors are linked with the dissolve  
cable, they behave like individual projectors and can also  
be operated individually as usual via the keypad.  
• If your SLAVE projector has a built-in timer, it must be  
switched off!  
• If you want to use only one projector in single mode,  
simply switch off the SLAVE and use the MASTER!  
Aligning the projectors  
It is important to align the two slide projectors before  
beginning a presentation such that both projected images  
cover the same area. This is easiest using so-called aligning  
slides which your AV dealer will certainly carry in stock (it  
is useful to load the aligning slide in the tray  
compartment 80):  
Projection with a single projector  
(Soft Slide Change)  
If you are just presenting with a single EKTAPRO 7010,  
7020, 9010 or 9020, you can fade your slides out and back in  
again (e.g. by setting a dissolve time to smoothly change the  
slides). This means the hard light change is avoided during  
slide transport.  
• Place the slide trays onto the projectors.  
• Press the slide reverse transport button on both projectors.  
• Focus both slides using the focus buttons on your  
projectors.  
The commands and notes which relate to the control of an  
individual projector are marked with an *.  
• Now align the projectors to project both slides on the same  
area.  
Projection with two projectors  
• Now return both slide trays to their initial position (zero  
position).  
Choosing projectors (MASTER/SLAVE)  
All commands for dissolving etc. are only transmitted to one  
projector. This projector is called the MASTER. It passes  
the commands on to the second projector which is known as  
the SLAVE.  
You can now begin your presentation using the remote  
control.  
Comment (EKTAPRO 7010, 7020, 9010 or 9020)  
If it is necessary to carry out any additional adjustment  
during the presentation push both transport buttons on the  
“dark” projector for longer than one second. The “dark”  
projector is now faded in too. Switch-off the lamp again by  
pressing standby.  
• You can use either the KODAK EKTAPRO 7010, 7020,  
9010 or 9020 projector as a MASTER  
• However, you can use all EKTAPRO models with a  
P-Bus-in interface as a SLAVE!  
Note: The use of all functions is only possible via  
EKTAPRO IR-Remote Control! With the KODAK  
EKTAPRO Cable Remote only dissolves in the default  
setting (0.5 sec) can be carried out.  
Sorting slides into the slide trays  
Once you have decided on the order of your slides, number  
them through. Then sort all the slides with uneven numbers  
in sequence into the slide tray for the MASTER projector.  
The slides with even numbers are sorted in order into the  
slide tray for the SLAVE projector (see the table page 34).  
Setting up  
Putting your 2 projector dissolve system together is fast and  
easy. Connect the two projectors via the P-bus-in interface to  
the KODAK Dissolve Cable (accessory) as shown in the  
illustration! Connect your remote control to the MASTER  
projector! Switch the projectors on. Your 2 projector  
dissolve system is now ready to use.  
6
 
COMMANDS AND EFFECTS  
Overview  
Examples:  
DISSOLVE  
If you want a dissolve time of  
1 s :➔ Input <810> and confirm with <*>.  
5.5 s :➔ Input <855> and confirm with <*>.  
0 s (Hard Cut) :➔ Input <800> and confirm  
with <*>.  
The following table gives and  
overview of all commands and effects.  
All commands with * can also be used  
for projection with a single  
EKTAPRO 7010, 7020, 9010 or 9020  
Projector!  
Basic setting  
After switching on you can  
immediately begin a dissolve  
presentation. Dissolving takes place  
with a default time of 0.5 seconds.  
As soon as you press the transport  
forwards button of the remote control  
both slide trays go to position 1 and the  
MASTER projector fades the no. 1  
slide up at the specified time. If you  
push the button again the first dissolve  
happens: slide no. 1 is faded down in  
the specified time and at the same time  
slide 2 is automatically faded up. Then  
the slide tray of the MASTER projector  
is automatically transported one  
position further and the projector is  
ready for the next dissolve. The  
dissolve process also functions in the  
same way when you push the transport  
backwards button.  
Important  
The dissolve time you have input is  
retained until you overwrite it with a  
new time (via the IR remote control).  
After a reset (switching off and back on  
again) the time you have input with the  
IR remote control is deleted (see Basic  
setting).  
Function  
Code  
* Setting dissolve times  
(Soft Slide Change in  
single projection)  
801 - 899  
* Random Access  
Fade (MASTER)  
Fade (SLAVE)  
0 - 160  
770  
707  
SELECTING SLIDES  
Alternate (Crossfading  
without slide change)  
777  
As in the case of individual projection,  
you can transport backwards and  
forwards at will, or select slides  
directly (random access). The slide  
sequence is always retained and the  
projector which is currently “dark” is  
automatically carried to the next slide  
in your presentation.  
* Freeze  
789  
980  
Independent Projector  
Control Mode  
Parallel Projection Mode  
970  
Notes:  
Activate Focus for SLAVE˚ 666˚  
You can interrupt a presentation if the  
dissolve time is greater than one  
second. If a dissolve has already  
started, it can be interrupted by  
pressing the forward button again at  
lest 1 sec into the dissolve. The  
presentation will move on to the next  
slide. Continuously pressing the  
forward button will interrupt each  
dissolve after one second and move on  
to the next.  
Reactivating of the dissolve 990  
mode  
* Remote Security Mode  
* Rest  
989  
999  
* Auto-Timer  
600 - 660  
˚ Function is inactivated for  
models 7010 and 9010!  
Tip  
• The last code input via the numerical  
keypad of the IR remote control  
remains stored. If the command has  
to be reinput, it is only necessary to  
press the <*> key.  
Dissolve times with IR remote  
control  
You can input  
dissolve times of  
0 seconds(so-called  
hard cut) up to a  
long dissolve of  
9.9 seconds in  
• If you input an incorrect figure on  
the numerical keypad of the IR  
remote control, press clear <C>  
before reinputting your figure.  
increments of a  
tenth of a second.  
The numerical combinations of  
800 ...899 on your remote control are  
reserved for this. Please ensure that you  
press the ENTER button <*> after  
inputting the relevant combination.  
Only then is the command received by  
the projector and the time stored. As  
soon as you press the transport button  
on your remote control, the first  
dissolve takes place.  
7
 
 
*Random Access  
Further control facilities  
With the commands “Fade  
MASTER”, “Fade SLAVE” and  
“Alternate” you can carry out  
*FREEZE (789)  
You select slides in 2 projector dissolve  
according to the slide number of your  
presentation and not according to the  
slide tray number (see the table on  
page 34)!  
With the Freeze command a soft  
dissolve can be stopped at any time  
(resp. fade in and fade out by single  
projection) and in any position. The  
dissolve can be continued by pressing  
the forward transport key. With the  
backwards transport key you can fade  
back accordingly.  
dissolves without a slide transport  
afterwards. When a dissolve command  
follows this will be carried out via  
forward transport key on the next slide  
and with the backward transport key on  
the previous slide. Therefore it is  
guaranteed, that the synchronicity will  
also be maintained by individual lamp  
status. The fade in and out time will be  
that of the dissolve time last set.  
With these commands you also can  
change the lamp status of the projectors  
when operated in the parallel mode  
(code 970) or in the individual control  
mode (code 980), whereby the new  
lamp status will be kept by further  
transport or soft slide changes. This  
opens up interesting possibilities for  
your presentation.  
Of course, if the  
slide you are  
looking for is in the  
slide tray of the  
projector which is  
currentlyprojecting  
a slide, a dissolve is  
not possible. The  
Press <789> and <*> on your remote  
control.  
Note: Mode switch-overs cannot be  
done in FREEZE. FREEZE can only be  
released by pressing the standby button  
or the transport buttons. If you release  
FREEZE by pressing the standby  
button, giving the standby command  
again will not return to FREEZE but  
will continue the dissolve.  
slide will first be faded down and the  
new slide faded up. In this case, the  
screen will stay blank during the  
transport period.  
However, if the slide you are looking  
for is in the slide tray of the projector  
which is currently “dark”, it will  
dissolve with the slide you are  
currently projecting.  
With Soft Slide Change the lamp lights  
up when FREEZE is ended by pressing  
the transport forwards button, and goes  
dark if the transport backwards button  
is pressed. No slide transport is carried  
out.  
Special feature: You can use the  
transport buttons during the dissolve  
procedure to change the direction of  
dissolve more than once. Once the  
dissolve procedure has finished,  
however, the slide is not transported.  
This only happens the next time you  
press the transport button. Pressing it  
again continues your presentation as  
normal.  
Zero compartment  
If there is a slide in the zero  
compartment of the slide tray, this can  
be selected by entering the following:  
161 for the MASTER projector;  
0 for the SLAVE projector.  
FADE MASTER (770)  
The MASTER projector's lamp can be  
faded in or faded out according to  
status. By re-pressing the button the  
command will be reversed.  
Press <770> and <*> on your remote  
control.  
Note: it is not possible to dissolve  
from 0 to 161 or vice versa.  
FADE SLAVE (707)  
Note: (EKTAPRO 7010 and 9010)  
If the slide tray (SLAVE) is transported  
on after a random access by pressing  
the transport buttons on the projector  
once or more, the previously selected  
slide cannot be accessed with a  
repeated random access command.  
(Example: on slide 36 with RA,  
transport forwards to slide 38, then  
back to slide 36 with RA cannot be  
done.)  
The SLAVE projector's lamp can be  
faded in or faded out according to  
status. By repressing the button the  
command will be reversed.  
Further presentation features  
Press <707> <*> on your remote  
control.  
INDIVIDUAL SLIDE  
TRANSPORT OF THE TWO  
PROJECTORS WITH REMOTE  
CONTROL (980)  
With the number combination <980>  
and <*> you can control the transport  
of the two projectors individually with  
the remote control.  
If this code is transmitted, the dissolve  
mode is cancelled and the lamps of  
both projectors remain on. Soft slide  
change cannot be carried out in this  
mode.  
*ALTERNATE (Dissolve  
without transport) (777)  
With the Alternate command the  
existing lamp status can be changed  
(see chart).  
Press <777> and <*> on your remote  
control.  
Press <980> and <*> on your remote  
control.  
8
 
 
Transport control on the MASTER:  
The slide transport runs, as usual, via  
the two transport buttons.  
Transport control on the SLAVE:  
The slide transport is via the two focus  
buttons.  
It is therefore not possible to focus the  
two projectors with this setting!  
Access to individual slides (RA  
control) is still possible (see *Random  
Access).  
hitches” can occur if the presenter  
presses the wrong button on the remote  
control by accident.  
*AUTOTIMER (600...660)  
A Timer function can also be set via the  
IR remote control. This is particularly  
relevant for the EKTAPRO 7010/7020  
as this does not have a built-in timer.  
Any time from 1 to 6 seconds can be  
set (in steps of one second). If you  
transmit such a command to the  
MASTER projector, the first transport  
command or the first dissolve is carried  
out immediately. This is a check for  
you that the projector is now in  
With the security setting you can set up  
your remote control so that when the  
transport button is pressed, only one  
transport step or only one dissolve is  
executed. The focus buttons are also  
disabled so that if you happen to press  
the buttons, the focus on the projector  
is not changed. All other functions  
remain active (and can be secured by  
the cover on the remote control). Even  
novice presenters can now “not put a  
foot wrong”!  
PARELLEL PROJECTION  
(970)  
You can also program parallel  
autotimer mode.  
Example  
projections via your remote control.  
Press <970> and <*>.  
Both projectors will then move to the  
same slide tray setting and both lamps  
are switched on.  
You want a dissolve to take place every  
22 seconds:  
➔ Press <622> and <*> on your  
remote control.  
The slide tray goes to position 1 and the  
first picture with the dissolve time is  
faded up. The first dissolve occurs after  
22 seconds.  
This is how to put your remote control  
into the security position:  
Press (989) and <*>.  
The following functions are changed:  
• Transport forwards:  
Regardless of how long you press a  
button, the projector only carries out  
a single transport step or the next  
dissolve. In case the parallel mode is  
activated the slides will only be  
projected if the button is released.  
Focussing:  
MASTER: With the focus buttons.  
SLAVE: First press <666> and <*>,  
then use focus buttons (not possible  
with models 7010 and 9010!).  
With a next slide transport this  
command is inactive again.  
The slides are numbered from 1 - 80  
(or 1 - 140 on a 140 slide tray) in this  
parallel mode and can be selected as  
such. If, for example, no. 13 is selected,  
both projectors will go into search  
mode and project the slides in the slide  
tray slot no. 13.  
Important  
Whilst the MASTER projector is  
carrying out a slide transport, no  
commands should be sent with the IR  
remote control. This can lead to the  
command not being recognized,  
especially in the case of very short  
autotimer times. In this case the  
projector should be switched off- and  
on again.  
• Transport backwards:  
Hold down the button for at least two  
seconds. The projector carries out a  
single step backwards and the slide  
will be projected in the moment the  
button is released.  
• Focus:  
Inactive  
Note:  
Switching the autotimer off  
You can turn the autotimer off again at  
any time:  
Press <600> and <*> on your remote  
control.  
• Of course the security position can  
also be used to control projection  
with a single projector.  
BACK INTO DISSOLVE MODE  
(990)  
By inputting this combination of  
numbers and the <*> you can go back  
to a basic setting for the two projector  
dissolve. The dissolve time previously  
set is retained.  
• For the individual projector control  
(980) this command cannot be  
applied.  
To cancel the security setting:  
The presentation mode can only be  
cancelled by a reset command or by  
switching the projectors off and on  
again [see *RESET (999)].  
Press <990> and <*> on your remote  
control.  
*SECURITY SETTING FOR  
PRESENTATIONS USING IR  
REMOTE CONTROL (989)  
If all the  
Press (999) and <*>.  
*RESET (999)  
preparations for a  
presentation have  
been made, it is  
important for a  
presentation to run  
“smoothly”. In  
spite of the best  
When you input this command, the two  
projectors are automatically reset to  
their zero position. Reset is the same as  
switching the projectors off and back  
on again (see also Basic setting).  
Press <999> and <*> on your remote  
control.  
preparation “small  
9
 
 
Slide Sorter Aid  
Position  
Position  
in  
MASTER  
tray  
Position  
in  
MASTER  
tray  
Position  
in  
MASTER  
tray  
Position  
in SLAVE  
tray  
Position  
in SLAVE  
tray  
Position  
in SLAVE  
tray  
Position  
in SLAVE  
tray  
Slide  
No.  
in  
Slide  
No.  
Slide  
No.  
Slide  
No.  
MASTER  
tray  
0
0
1
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
64  
65  
66  
67  
68  
69  
70  
71  
72  
73  
74  
75  
76  
77  
78  
79  
80  
81  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
82  
83  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
123  
124  
125  
126  
127  
128  
129  
130  
131  
132  
133  
134  
135  
136  
137  
138  
139  
140  
141  
142  
143  
144  
145  
146  
147  
148  
149  
150  
151  
152  
153  
154  
155  
156  
157  
158  
159  
160  
161  
62  
63  
64  
65  
66  
67  
68  
69  
70  
71  
72  
73  
74  
75  
76  
77  
78  
79  
80  
1
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
64  
65  
66  
67  
68  
69  
70  
71  
72  
73  
74  
75  
76  
77  
78  
79  
2
1
2
84  
3
2
3
85  
4
86  
5
87  
6
3
88  
7
4
89  
8
4
90  
9
5
91  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
5
92  
6
93  
6
94  
7
95  
7
96  
8
97  
8
98  
9
99  
9
100  
101  
102  
103  
104  
105  
106  
107  
108  
109  
110  
111  
112  
113  
114  
115  
116  
117  
118  
119  
120  
121  
122  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
80  
0
34  
 

Invacare Personal Lift 5143 User Manual
JBL Car Speaker 28T 60 User Manual
JBL Portable Speaker FLIPIIBLK User Manual
Jensen Handheld TV JDTV 1020 User Manual
JVC Stereo Receiver RX 7001PGD User Manual
Keating Of Chicago Fryer 14 TS User Manual
Keys Fitness Fitness Equipment ST 205 User Manual
Kidde Smoke Alarm KN COPP B LS User Manual
Kolcraft Stroller S67 T R1 User Manual
Konftel Printer G510 7276 00 User Manual