GS8 GS12
GS8 and GS12 Eco-System™ Amplifier specifications:
Eco-System Power
Amplifiers
Inputs:
Input impedance:
Outputs:
Output power:
Peak output power:
Ideal impedance:
8 or 12 gold RCA jacks with adjustable gain
50k ohms
5 way gold binding posts
50 watts RMS per channel (8 ohms)
100 watts per channel (8 ohms)
4 – 8 ohms
Installation Instructions v1.2
Warning: To be installed and/or used in accordance with
appropriate electrical codes and regulations.
Frequency response: 10 Hz – 40 kHz +/- 1dB (1w)
S/N ratio:
Over 105 dB A weighted (50 watts)
Less than 0.1% 20 Hz to 20 kHz
Less than 0.01% 60 Hz 7 kHz 4:1 (SMPTE)
17” x 3.5” x 11.5” (432 x 89 x 292 mm)
Quiet 28 dBA
THD distortion:
IMD distortion:
Dimensions:
Fan noise:
Introduction: Thank you for your purchase of a Knoll
Eco-System multi-channel power amplifier and
congratulations on your choice. This amplifier is
specifically designed to save energy when idling, which
can be most of the time. When compared to similar power
amplifiers the GS8 and GS12 uses less than 5% of the
energy required for normal amps to idle.
Power:
Standby in Eco-System™ less than 5 watts
Maximum 750 watts at 117 VAC or 230VAC
GS8 20 lbs (9 kg); GS12 22 lbs (10 kg)
Steel chassis, powder coated; glass epoxy
printed circuit boards
Weight:
Construction:
FEATURES:
•
•
•
Eco-System™ Circuitry saves energy (and
money) and increases power.
12 channels x 50 watts RMS at 8 Ohms (over
100W peak). GS8 8 channels.
Individual and automatic channel resetting
protection for low impedance, overheating,
overloading, overvoltage and undervoltage.
Individual gain controls for all channels.
Electronic Link feature connects stereo inputs
channel 2 through 6 to channel 1. GS8 connects
stereo inputs channel 2 through 4 to channel 1.
Side-mounted thermostatically controlled fan for
internal cooling.
Warranty
Knoll Systems warrants its products sold in the USA and Canada by
authorized Knoll dealers to be free of defects in materials and
workmanship. This warranty extends for three full years from the date
of purchase by the original consumer. Any products returned to Knoll
Systems and found to be defective by Knoll Systems within the
warranty period will be repaired or replaced at Knoll Systems option, at
no charge. Knoll Systems will not be responsible for the actual cost of
installation or removal of the product, nor for any incidental or
consequential damages. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above
limitation may not apply to you. This warranty gives you specific legal
rights. You may have additional legal rights that vary from state to
state.
•
•
•
•
Two rack spaces (3-1/2”) with optional rack
mount version.
145 Tyee Drive Point Roberts, WA 98281
12140 Horseshoe Way Richmond BC V7A 4V4
tel (604) 272 4555, fax (604) 272 5595
Made in Canada GS18 and GS12, 2005, Knoll Systems All Rights Reserved
8. Make sure the speakers in each room are connected in phase
with the amplifier + going to the speaker +. Out of phase
speakers give unstable imaging and poor bass response.
9. Connect the AC power into an outlet than can supply at least
six amps (750 watts) dedicated to each GS8 or GS12.
10. After the amp has been turned on adjust the “SENS” pot on
the rear of the amplifier if necessary. The “SENS” adjustment
can be adjusted up (clockwise) to make the amp less
susceptible to be turned on due to nuisance noise and hum. If it
is adjusted too high, the amp may delay turn on or turn off
during a quiet music or speech passage.
Installation
Installing the amplifier should be relatively easy. With a bit of
planning, this amplifier will give trouble free service for years.
1. The most important consideration when installing the
GS8 and/or GS12 is cooling. This amplifier has a lot of power
packed into a small chassis size. When installing it in an
equipment stack, it should be the top component. It needs at
least 3"-5" of space above the amplifier to allow for adequate
convection cooling.
2. When installing the GS8 and/or GS12 in a rack we suggest
adding a 3-1/2" blank above and below the amplifier. In
multiple GS8 and GS12 installations, plan for a 3-1/2" blank
(double) between each amplifier and a 3-1/2" blank on the top
and bottom. Amplifiers should always be the top components in
a rack system.
Caution: Never listen to sound that is distorted. If distorted
sound is heard, turn the volume down immediately or speaker
and/or amplifier damage could occur that is not covered by the
warranty. If this problem persists, contact your dealer.
User Adjustments and Service: There are no user
adjustments inside the GS8 or GS12. Your installer may make
certain gain and sensitivity level adjustments on the rear panel.
3. The GS8 and GS12 are available as an optional 19" EIA rack
mount style.
4. Never operate a GS8 or GS12 on its side, as the cooling
potential drops significantly when operated on the side.
5. Connect the GS8 or GS12 RCA inputs to the source
component outputs with good quality, short as possible RCA
jack cables. Connect each channel individually.
6. Connect the GS8 or GS12 speaker outputs to speakers using
good quality speaker wire. Minimum 16 gauge copper wire is
recommended with 14 gauge minimum for runs over 30' (10m).
Fire-rated wire may be required if installing wires inside walls,
ceilings or floors.
Caution: The GS8 or GS12 contains no user serviceable parts,
so do not attempt to open or repair the GS8 or GS12.
Refer servicing to a qualified technician only or contact the
factory for information.
Troubleshooting
If a problem is encountered with the GS8 or GS12 amplifier, the
most expedient procedure is to locate the problem and if
possible repair it before requesting service. Be sure to carefully
check other system components such as controllers, CD players,
volume controls, wiring, speakers, etc. that may be at fault.
Note: Ideally the GS8 and GS12 amplifiers like 6-8 ohm loads.
Connecting to 4-ohm loads won't hurt the amplifier, but the
channels connected to 4-ohm loads may occasionally shutdown
due to overloading. Never connect any GS8 or GS12 amplifier to
less than 4 ohms.
Problem
Power led does
not light - no sound
Action
1. Check that the GS8 or GS12 is plugged
in.
2. Test the AC outlet with a lamp.
3. Check GS8 or GS12 power button is on
(in).
7. Individually adjust the channel gains as required. Ideally, all
gains are fully on (fully clockwise).
4. Slowly turn down the “SENS”
adjustment (counterclockwise) on the
amplifier rear, until the amplifier just
turns on.
(continued)
Caution: NEVER connect the GS8 or GS12 to impedances
less than 4 ohms or amplifier damage not covered by the
warranty may occur.
GS12 Rear Panel
The Link button is normally set to the in position to give
all six stereo inputs individual sources. When a channel
Link button is set to the out position, that channel is
(Left/Right) linked or cascaded to input #1 (without the
use of Y cords). Any or all combinations of linked inputs 2
to inputs 6 are possible. When all inputs are linked to
input one, the input impedance is about 8500 ohms.
The “SENS” pot controls the level threshold setting of the
automatic power on and off to all channels. Each channel
turns on and off individually.
Power On
Initially adjust the “SENS” on to about 1/3 level. Turn on a
source to one or more channels and see if the channel
turns on (observe the front panel led). With soft music on,
the channel should sense the music and turn on. If it does
not turn on, try turning the “SENS” adjustment counter
clockwise slowly until the channel turns on.
Note: When linked unused RCA inputs can be used as
outputs to other amplifiers.
Power Off
If the channel does not turn off about 3-30 seconds after
a source has been muted or shut off, adjust the “SENS”
slowly clockwise and wait 30 seconds. If it still does not
turn off, turn it a bit more clockwise and wait another 30
seconds. Keep doing this until the channel turns off in 3-
30 seconds.
Note 1: Ideal speaker impedance is 6-8 ohms.
|