®
Undercounter Dishwasher
PRODUCT MODEL SERIES
OVERALL DIMENSIONS
KUDD01DPPA
23-7/16"
(59.5 cm)
22-7/16" *
(57 cm)
raised tabs for
optional top
attaching brackets
Electrical: A 120-volt, 60 Hz, AC-only, 15-amp
fused electrical supply is required. (Circuit breaker
or time-delay fuse is recommended.) It is
recommended that a separate circuit serving only
this appliance be provided.
32-3/16"- 34-1/2"
(81.8 cm - 87.8 cm)
30" ***
(76.2 cm)
The 3 prong grounded outlet must be installed
within 6" (15.2 cm) to 18" (45.7 cm) of the cabinet
side wall.
If you plan to install a garbage disposer, an
additional separate 120-volt, 60 Hz, AC-only,
15- or 20-amp fused electrical supply is required.
Water: A hot water line with 4.3-145 psi
(30-1000 kPa) water pressure must be used.
Water temperature must be minimum 120°F
(49°C) at dishwasher. An easily accessible valve
with 3/8" compression fitting must be installed in
the hot water supply line.
* If custom wood panels are to be used,
the product depth is specified with an
11/16" (18 mm) door panel thickness.
side
attaching
tabs
** Toe panel depth: Factory supplied,
2–4-3/8" (5 – 11 cm); Custom wood,
5" (12.7 cm) less the toe panel
thickness for integrated. Minimum
panel thickness using the supplied
screws is 3/8" (9 mm).
*** Door front height: Factory supplied –
30" (76.2 cm); Custom wood – 28-1/4"
(71.8 cm) minimum.
2"– 4-3/8" **
(5 cm – 11 cm)
20-15/32"
(52 cm)
NOTE: Product shown with front panels
for dimension purposes.
drawer open
CABINET OPENING DIMENSIONS
*IMPORTANT: Custom wood door panels, if
used, may be wider than the dishwasher to
match surrounding cabinets. The 23-5/8"
(60.0 cm) must be increased so that there is
a 1/4" (6.4 mm) clearance between the
cabinet side and panel edge.
moisture protection tape
4"
(10 cm)
For corner installation, there must be a 1/2"
(12.7 mm) space between the adjacent
cabinet doors (i.e. door knobs) and open
dishwasher drawer.
32-5/16"– 34-5/8"
(82.0 cm – 88.0 cm)
Utility hole:
1-1/2" (3.8 cm) dia.
hole, either side –
immediately adjacent
to corner.
DRAIN OPTIONS
Garbage disposal
connection
Sink drain waste
tee connection
22-7/8"
(58.0 cm)
drain hose
support
drain hose
support
23-5/8"* (60.0 cm)
Air break connection
air break
drain hose
connector
6" (15.2 cm)
minimum
waste tee
waste
garbage
disposal
waste
valve
valve
waste
water supply
27-1/2" – 32-1/4"
(70 cm – 82 cm)
water supply
water supply
8" (20.3 cm) min. bend
radius from valve
8" (20.3 cm) min. bend
radius from valve
Because Whirlpool Corporation policy includes a continuous commitment to improve our
products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. 8546448
12-2-04
®
KitchenAid Double Drawer Dishwasher Custom Door Panel Requirements
MODELS: KUDD01DPPA
Horizontal
Position Line
7) On the back side of the top drawer custom door panel,
1 7⁄16”
(36.5 mm)
rout a 1⁄4” (6.4 mm) radius around the medallion cutout
previously cut in step #4. The medallion end does not
need to be routed.
CUSTOM
PANEL FOR
TOP DRAWER
(Back Side)
8) On the back side of the bottom drawer custom door
panel, rout a 1⁄4” (6.4 mm) radius around the medallion
cutout previously cut in step #5. The medallion end does
not need to be routed.
Vertical
Center Line
Medallion
Location Area
9) If custom door panel material is not suitable to withstand
damp conditions, seal with a moisture resistant material.
For painted panels, paint all rear edges to improve sealing.
FIGURE 3A
10) On the backside of the top drawer custom door panel,
measure and mark the vertical center line and horizontal
position line (See figure 3A).
Horizontal
NOTE: The 1 7⁄16” (36.5 mm) horizontal position line is
marked for later use in the installation process. Refer to
the Installation Instructions Drawer Dishwasher included
with the Drawer Dishwasher to align and attach the top
drawer custom door panel to the factory supplied
metal plate.
Position Line
1 3⁄16”
(30.2 mm)
CUSTOM
PANEL FOR
BOTTOM
DRAWER
(Back Side)
11) On the backside of the bottom drawer custom door
panel, measure and mark the vertical center line and
horizontal position line (See figure 3B).
Medallion
Location Area
Vertical
Center Line
NOTE: The 1 3⁄16” (30.2 mm) horizontal position line is
marked for later use in the installation process. Refer to
the Installation Instructions Drawer Dishwasher included
with the Drawer Dishwasher to align and attach the
bottom drawer custom door panel to the factory supplied
metal plate.
FIGURE 3B
12) Mount the customer supplied handles to the locations
previously marked on the top and bottom drawer
custom panels.
IMPORTANT: When mounting the customer supplied
handles, screws must fit flush to the panel and not extend
beyond the back surface.
13) Refer to the Installation Instructions Drawer
Dishwasher included with the Drawer Dishwasher
to complete installation.
|