Kicker Stereo Amplifier ZX4001 User Manual

ZX  
SUBWOOFERAMPLIFIER  
CLASS-DMONOCHANNEL  
ZX400.1, ZX750.1  
©2006 Stillwater Designs  
 
recommended impedance and multiple speaker wiring suggestions). Also check for adequate airflow  
around the amplifier. 2) Amplifier shuts down only while vehicle is running. Voltage protection  
circuitry is engaged. Voltage to the amplifier is not within the 9-16 volt operating range. Have the  
vehicle's charging and electrical system inspected. 3) Amplifier will only play at low volume levels.  
Short circuit protection is engaged. Check for speaker wires shorted to each other or to the vehicle  
chassis. Check for damaged speakers, or speaker(s) operating below the minimum recommended  
impedance.  
Operation  
Your Kicker ZX.1 series amplifier has three rotary controls on top and one switch on the end-panel.  
Before turning on the system for the first time, turn the three rotary controls on the top of the amplifier  
to the full counter-clockwise position.  
1. SubsonicFilterSwitch The subsonic filter switch located on the end-panel utilizes an internal  
12dB per octave at 25 Hz high-pass  
crossover in the ON position. The  
No or low output? 1) Check the balance and fader control on source unit 2) Check the RCA  
(or speaker input) and speaker output connections  
Figure 3  
-
setting for this control is subjective;  
the ON position is a good place to  
start. Never change the subsonic filter  
switch “ON/OFF” setting with the  
audio system on! See Figure 1.  
Alternator noise-whining sound with engine’s RPM? 1) Check for damaged RCA (or speaker  
input) cable 2) Check the routing of RCA (or speaker input) cable 3) Check the source unit for proper  
grounding 4) Check the gain settings and turn them down if they are set too high.  
+
Reduced bass response? Check system phasing by reversing a speaker connection from  
positive to negative on the stereo/subwoofer channel(s); if the bass improves, the speaker was out  
of phase.  
2. InputGainControl The input gain  
control is not a volume control. It  
matches the output of the source unit  
to the input level of the amplifier. Turn  
the source unit up to about 3/4 volume (if the source unit goes to 30, turn it to 25). Next, slowly turn  
(clockwise) the gain on the amplifier up until you can hear audible distortion, then turn it down a little.  
Crossover Control  
50 - 200Hz, 24dB/Oct  
Input Gain Control  
Low Level: 125mV - 5V, High Level: 250mV - 10 V  
Bass Boost Control  
0 to +18dB boost @ 40Hz  
If you have more questions about the installation or operation of your new KICKER product, see the  
Authorized KICKER Dealer where you made your purchase. For more advice on installation, click on the  
choose the subject you are interested in, and then download or view the corresponding information.  
Please E-mail support@kicker.com or call Technical Services (405) 624-8583 for unanswered  
or specific questions.  
3. BassBoostControl The bass boost control is designed to give you increased output 0 - 18dB  
at 40 Hz. The setting for this control is subjective. If you turn it up, you must go back and adjust the  
input gain control to avoid clipping the amplifier.  
CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are  
correct. Improper connections can result in blown amplifier fuses as well as the failure of other critical  
systems in the vehicle.  
4. CrossoverControl The setting for this control is subjective; 80Hz is a good place to start.  
5. RemoteBass(Level Control) With the remote bass level control you have the ability to control the  
level of the subwoofer(s) remotely by controlling the output level of one or more ZX series amplifiers. To  
mount the remote bass level control, simply screw the metal bracket to the chosen location. Then slide  
the housing onto the bracket until it  
Performance  
Figure 4  
Mount the metal bracket  
Model  
ZX400.1  
ZX750.1  
snaps into place. Run the cable from  
the controller to the “Remote Bass”  
Back View  
Side View  
RMS Power in Watts, all channels driven  
@14.4V, 4Ω Mono 1.5% THD+N  
@14.4V, 2Ω Mono, 1.5% THD+N  
Length:  
jack on the amplifier chassis.  
200 x 1  
400 x 1  
375 x 1  
750 x 1  
TroubleShooting  
10 1/4” (260mm) 14 11/16” (373mm)  
Slide the housing until it snaps into the metal bracket  
If your amplifier does not appear to  
Specifications common to all models:  
L
R
L
R
be working, check the obvious things  
first such as blown fuses, poor or  
incorrect wiring connections,  
incorrect setting of crossover switch  
and gain controls, etc. There are two  
LEDs on the top of your Kicker ZX  
series amplifier, one green and one  
HI-LEVEL  
INPUT  
+
-
-
+
ON OFF  
SUB SONIC  
INPUT  
OUTPUT  
Height:  
Width:  
2 1/8” (54mm)  
9 5/8” (244mm)  
20 Hz - 200 Hz  
REMOTE  
BASS  
+
-
Frequency Response, + 0 / - 1 dB:  
Signal-to-Noise Ratio:  
Input Sensitivity:  
4 Conductor  
Phone Cable  
>95 dB, a-weighted, re: rated power  
125 mV - 5 V low level, 250 mV - 10 V high level  
Variable Low-Pass, 50 - 200Hz, 24dB per octave  
Defeatable High-Pass 12 dB per octave @ 25 Hz  
Variable 0 to +18 dB boost @ 40 Hz  
Electronic Crossover:  
red. When the green LED is lit this indicates the amplifier is turned on and no trouble exists. If the green  
LED turns off and the red LED is lit, this indicates that the protection circuitry (SORT) is engaged.  
Bass Boost:  
Green LED off, no output? With a Volt Ohm Meter (VOM) check the following: 1) +12 volt power  
terminal (should read +12V to +16V) 2) Remote turn-on terminal (should read +12V to +16V)  
3) Check for reversed power and ground connections 4) Ground terminal, for proper conductivity.  
Model ZX400.1  
200 x 1 @ 4 ohms, 14.4Vdc, 1% THD,  
CEA-2006 (Watts)  
Signal to Noise Ratio -55 CEA-2006  
(ref: 1W, A-weighted)  
Green LED on, no output? Check the following: 1) RCA connections 2) Test speaker outputs  
with a “known” good speaker. 3) Substitute source unit with a “known” good source unit. 4) Check  
for a signal in the RCA cable feeding the amplifier with the “AC” test position selected on the  
VOM meter.  
Model ZX750.1  
375 x 1 @ 4 ohms, 14.4Vdc, 1% THD,  
CEA-2006 (Watts)  
Signal to Noise Ratio -62 CEA-2006  
(ref: 1W, A-weighted)  
Red LED on, no output? 1) Amplifier is very hot. Thermal protection is engaged. Test for proper  
impedance at the speaker terminals with a VOM meter (see the diagrams in this manual for minimum  
 
ZX.1AMPLIFIER  
4
5
ElectronicsLimitedWarranty  
InternationalWarranty  
Kicker warrants this product to be free from defects in material and workmanship under normal use for a period of  
THREE (3) MONTHS from date of original purchase with receipt. When purchased from an Authorized KICKER Dealer  
it is warranted for TWO (2) YEARS from date of original purchase with receipt. In all cases you must have the original  
receipt. Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction  
during the warranty period, Kicker will repair or replace (at its discretion) the defective merchandise with equivalent  
merchandise at no charge. Warranty replacements may have cosmetic scratches and blemishes. Discontinued  
products may be replaced with more current equivalent products.  
Contact your International Kicker dealer or distributor concerning specific procedures for your country's warranty  
policies.  
WARNING: KICKER products are capable of producing sound levels that can permanently damage your hearing!  
Turning up a system to a level that has audible distortion is more damaging to your ears than listening to an  
undistorted system at the same volume level. The threshold of pain is always an indicator that the sound level is too  
loud and may permanently damage your hearing. Please use common sense when controlling volume.  
This warranty is valid only for the original purchaser and is not extended to owners of the product subsequent to the  
original purchaser. Any applicable implied warranties are limited in duration to a period of the express warranty as  
provided herein beginning with the date of the original purchase at retail, and no warranties, whether express or  
implied, shall apply to this product thereafter. Some states do not allow limitations on implied warranties; therefore  
these exclusions may not apply to you. This warranty gives you specific legal rights; however you may have other  
rights that vary from state to state.  
GARANTÍA INTERNACIONAL  
VersiónEspañol  
Comuníquese con su concesionario o distribuidor Kicker internacional para obtener infor ación sobre procedimientos  
específicos relacionados con las normas de garantía de su país.  
ADVERTENCIA: Los excitadores Kicker son capaces de producir niveles de sonido que pueden dañar  
permanentemente el oído. Subir el volumen del sistema hasta un nivel que produzca distorsión es más dañino para el  
oído que escuchar un sistema sin distorsión al mismo volumen. El dolor es siempre una indicación de que el sonido es  
muy fuerte y que puede dañar permanentemente el oído. Sea precavido cuando controle el volumen.  
WHAT TO DO IF YOU NEED WARRANTY OR SERVICE  
Defective merchandise should be returned to your local Authorized Stillwater Designs (Kicker) Dealer for warranty  
Designs directly. You can confirm that a dealer is authorized by asking to see a current authorized dealer window  
decal.  
La frase "combustible para vivir la vida Livin' Loud™ a todo volumen" se refiere al entusiasmo por la vida que la marca  
Kicker de estéreos de automóvil representa y a la recomendación a nuestros clientes de que vivan lo mejor posible ("a  
todo volumen") en todo sentido. La línea de altavoces y amplificadores Kicker es la mejor del mercado de audio de  
automóviles y por lo tanto representa el "combustible" para vivir a todo volumen en el área de "estéreos de automóvil"  
de la vida de nuestros clientes. Recomendamos a todos nuestros clientes que obedezcan todas las reglas y  
reglamentos locales sobre ruido en cuanto a los niveles legales y apropiados de audición fuera del vehículo.  
If it becomes necessary for you to return defective merchandise directly to Stillwater Designs (Kicker), call the Kicker  
Customer Service Department at (405) 624-8510 for a Return Merchandise Authorization (RMA) number. Package all  
defective items in the original container or in a package that will prevent shipping damage, and return to:  
INTERNATIONALE GARANTIE  
DeutscheVersion  
Stillwater Designs, 5021 North Perkins Road, Stillwater, OK 74075  
Nehmen Sie mit Ihren internationalen Kicker-Fachhändler oder Vertrieb Kontakt auf, um Details über die  
Garantieleistungen in Ihrem Land zu erfahren.  
The RMA number must be clearly marked on the outside of the package. Please return only defective components.  
The return of functioning items increases your return freight charges. Non-defective items will be returned freight-  
collect to you.  
WARNUNG: KICKER-Treiber können einen Schallpegel erzeugen, der zu permanenten Gehörschäden führen kann!  
Wenn Sie ein System auf einen Pegel stellen, der hörbare Verzerrungen erzeugt, schadet das Ihren Ohren mehr, als ein  
nicht verzerrtes System auf dem gleichen Lautstärkepegel. Die Schmerzschwelle ist immer eine Anzeige dafür, dass  
der Schallpegel zu laut ist und zu permanenten Gehörschäden führen kann. Seien Sie bei der Lautstärkeeinstellung  
bitte vernünftig!  
Include a copy of the original receipt with the purchase date clearly visible, and a "proof-of-purchase" statement listing  
the Customer's name, Dealer's name and invoice number, and product purchased. Warranty expiration on items  
without proof-of-purchase will be determined from the type of sale and manufacturing date code. Freight must be  
prepaid; items sent freight-collect, or COD, will be refused.  
Der Slogan "Treibstoff für Livin' Loud" bezieht sich auf die mit den Kicker-Autostereosystemen assoziierte  
Lebensfreude und die Tatsache, dass wir unsere Kunden ermutigen, in allen Aspekten ihres Lebens nach dem Besten  
("Livin' Loud") zu streben. Die Lautsprecher und Verstärker von Kicker sind auf dem Markt für Auto-Soundsysteme  
führend und stellen somit den "Treibstoff" für das Autostereoerlebnis unserer Kunden dar. Wir empfehlen allen unseren  
Kunden, sich bezüglich der zugelassenen und passenden Lautstärkepegel außerhalb des Autos an die örtlichen  
Lärmvorschriften zu halten.  
WHAT IS NOT COVERED?  
This warranty is valid only if the product is used for the purpose for which it was designed.  
It does not cover:  
o Damage due to improper installation  
o Subsequent damage to other components  
o Damage caused by exposure to moisture, excessive heat, chemical cleaners, and/or UV radiation  
o Damage through negligence, misuse, accident or abuse. Repeated returns for the same damage may be  
considered abuse  
o Any cost or expense related to the removal or reinstallation of product  
o Speakers damaged due to amplifier clipping or distortion  
o Items previously repaired or modified by any unauthorized repair facility  
o Return shipping on non-defective items  
o Products with tampered or missing barcode labels  
o Products returned without a Return Merchandise Authorization (RMA) number  
o Freight Damage  
GARANTIE INTERNATIONALE  
VersionFrançaise  
Pour connaître les procédures propres à la politique de garantie de votre pays, contactez votre revendeur ou  
distributeur International Kicker.  
AVERTISSEMENT: Les haut-parleurs Kicker ont la capacité de produire des niveaux sonores pouvant endommager  
l'ouïe de façon irréversible ! L'augmentation du volume d'un système jusqu'à un niveau présentant une distorsion  
audible endommage davantage l'ouïe que l'écoute d'un système sans distorsion au même volume. Le seuil de la  
douleur est toujours le signe que le niveau sonore est trop élevé et risque d'endommager l'ouïe de façon irréversible.  
Réglez le volume en faisant prevue de bon sens !  
o The cost of shipping product to Kicker  
o Service performed by anyone other than Kicker  
L'expression " carburant pour vivre plein pot " fait référence au dynamisme de la marque Kicker d'équipements audio  
pour véhicules et a pour but d'encourager nos clients à faire le maximum (" vivre plein pot ") dans tous les aspects de  
leur vie. Les haut-parleurs et amplificateurs Kicker sont les meilleurs dans le domaine des équipements audio et  
représentent donc pour nos client le " carburant pour vivre plein pot " dans l'aspect " installation audio de véhicule "  
de leur vie. Nous encourageons tous nos clients à respecter toutes les lois et réglementations locales relatives aux  
niveaux sonores acceptables à l'extérieur des véhicules.  
HOW LONG WILL IT TAKE?  
Kicker strives to maintain a goal of 72-hour service for all electronics (amplifiers, crossovers, equalizers, etc.) returns.  
Delays may be incurred if lack of replacement inventory or parts is encountered.  
Failure to follow these steps may void your warranty. Any questions can be directed to the Kicker Customer Service  
Department at (405) 624-8510.  
Note: To get the best performance from your new Kicker Amplifier, we recommend using genuine Kicker Accessories and Wiring.  
P.O. Box 459 • Stillwater, Oklahoma 74076 • U.S.A. • (405) 624-8510  
12282005+06ZX.1  
 
ZX.1AMPLIFIER  
6
7

IOGear Switch GCS661U User Manual
JVC CRT Television 0803 NIC JMT User Manual
Keys Fitness Elliptical Trainer ET4000 User Manual
Kidde Smoke Alarm 820 0898 User Manual
KitchenAid Clothes Dryer KEYE900T User Manual
KitchenAid Ice Maker KUIS18PNJB8 User Manual
KitchenAid Refrigerator W10233586 User Manual
Klaxon Smoke Alarm 110 DC User Manual
Knoll Systems Projector HD102 User Manual
Kodak Digital Camera CX7300 User Manual