Kenwood Stereo Receiver KMD PS971R User Manual

MD-RECEIVER

KMD-PS971R

INSTRUCTION MANUAL

B64-1619-00 (EN)

Safety precautions

IMPORTANT INFORMATION

2WARNING

2CAUTION

You cannot connect the unit directly to the

following CD automatic changers. For users

who want to use older changers with the

unit, follow the directions below according to

the type of changer you own:

To prevent injury and/or fire, take the

following precautions:

• Insert the unit all the way until it is fully

locked in place. Otherwise it may fly out of

place during collisions and other jolts.

To prevent damage to the machine,

take the following precautions:

• Make sure to ground the unit to a negative

12V DC power supply.

• KDC-C200 / KDC-C300 / KDC-C400

• Do not open the top or bottom covers of the

unit.

• Do not install the unit in a spot exposed to

direct sunlight or excessive heat or humidity.

Also avoid places with too much dust or the

possibility of water splashing.

• Do not subject the faceplate to excessive

shock, as it is a piece of precision

equipment.

• When replacing a fuse, only use a new one

with the prescribed rating. Using a fuse with

the wrong rating may cause your unit to

malfunction.

• To prevent short circuits when replacing a

fuse, first disconnect the wiring harness.

• Do not place any object between the

faceplate and the unit.

• During installation, do not use any screws

except for the ones provided. The use of

improper screws might result in damage to

the main unit.

Use the extension cable and the control box

attached to the CD changer, and the optional

CA-DS100 converter cable.

• KDC-C301 / KDC-C600 / KDC-C800 / KDC-

C601 / KDC-C401

Use the extension cable attached to the CD

changer, and the optional CA-DS100

converter cable.

• KDC-C100 / KDC-C302 / C205 / C705 /

non-Kenwood CD changers

• When extending the ignition, battery or

ground cables, make sure to use automotive-

grade cables or other cables with an area of

0.75mm (AWG18) or more to prevent cable

deterioration and damage to the cable

coating.

• To prevent short circuits, never put or leave

any metallic objects (e.g., coins or metal

tools) inside the unit.

• If the unit starts to emit smoke or strange

smells, turn off the power immediately and

consult your Kenwood dealer.

• Make sure not to get your fingers caught

between the faceplate and the unit.

• Be careful not to drop the unit or subject it to

strong shock.

Cannot be used with this model.

2CAUTION

You can damage both your unit and

the CD changer if you connect them

incorrectly.

The unit may break or crack because it

contains glass parts.

• Do not apply excessive force to the moving

faceplate. Doing so will cause damage or

malfunction.

• Do not apply excessive force to the open

faceplate or place objects on it. Doing so will

cause damage or breakdown.

US and foreign patents Iicensed from Dolby

Laboratories Licensing Corporation.

— 3 —

Safety precautions

• The illustrations of the display and the panel

appearing in this manual are examples used

to explain more clearly how the controls are

used. Therefore, what appears on the display

in the illustrations may differ from what

appears on the display on the actual

equipment, and some of the illustrations on

the display may represent something

impossible in actual operation.

• The functions that can be used and the

information that can be displayed will differ

depending on the external disc players being

connected.

Mask key

NOTE

If you have transmitted the Mask Key's

signal once to the unit in advance, you will

have to transmit it once again if the unit has

been removed from the battery. This

function helps prevent theft.

• If you experience problems during

installation, consult your Kenwood dealer.

Egnlish

• If the unit fails to operate properly, press the

RESET button. When the faceplate controls

are not visible, press the left part at the

upper side of the faceplate (as illustrated on

p.15) for as many times as you have preset

to make the faceplate controls appear. The

unit returns to factory settings when the

RESET button is pressed. After you press

the reset button, the Mask Key will be

needed to restart the unit. If the unit still fails

to operate properly after the RESET button

has been pressed, contact your local

When using the unit for the first time:

In order to deactivate the demonstration

mode, be sure to press the transmit button

to transmit the Mask Key's signal.

If this procedure is not carried out, the

control panel of the unit will re-open in two

seconds even with your vehicle's ignition

turned off.

2CAUTION

Do not loose the "Mask Key".

If power is disconnected from the unit,

correct operation can only be restored by the

"Mask Key's" signal.

KENWOOD dealer for assistance.

Cleaning the Faceplate Terminals

If the terminals on the unit or faceplate get

dirty, wipe them with a dry, soft cloth.

• Press the reset button if the CD auto

changer is first controlled and operates

incorrectly. The original operating condition

will return.

The "Mask Key" will also be required for

service repair.

Cleaning the Unit

If the front panel gets dirty, turn off the

power and wipe the panel with a dry silicon

cloth or soft cloth.

KMD-PS971R

4.5V

PREOUT

NOTE

If you send products in for repair that include

a mask key, make sure to present the unit

together with the mask key.

2CAUTION

Do not wipe the panel with a stiff cloth or a

cloth dampened by volatile solvents such as

paint thinner and alcohol. They can scratch

the surface of the panel and/or cause the

indicator letters to peel off.

Reset button

Lens Fogging

In cold climates, there may be a period after

you turn on your vehicle's heater when the

lens that guides the laser beam used in your

MD player fogs up. If this happens, you

cannot play mini discs. Take out discs and

the fogging will disappear. If it does not

return to normal after several hours, contact

your Kenwood dealer.

— 4 —

Handling Mini discs

The marking of products using lasers

(Except for some areas)

• The MD shutter is designed so that it cannot

be opened. If forced open, the cartridge will

be damaged and use of the MD will no

longer be possible. If the shutter has been

opened due to some cause, be careful not to

touch the recording portion with a finger.

Doing so will cause the sound to skip.

CLASS 1

LASER PRODUCT

The label is attached to the chassis/case and

says that the component uses laser beams

that have been classified as Class 1. It

means that the unit is utilizing laser beams

that are of a weaker class. There is no

danger of hazardous radiation outside the

unit.

• Do not use an MD that has a peeling label.

Use of an MD that has a loose or peeling

label may cause problems, such as the label

coming off inside the player and the

resultant inability to eject the MD.

• Wipe away dirt or dust from the cartridge

surface with a dry cloth before use. Using an

oil-soiled cartridge in particular may result in

the disc not loading or being unable to eject

it. (At time of cleaning, be careful not to

open the shutter.)

• Do not leave the MD in the unit for a

prolonged period. The ejected MD should be

placed in an MD case for storage.

• Do not leave the MD in a place exposed to

direct sunlight (such as on a instrument

panel) or in other places that reach high

temperatures. The MD cartridge will become

misshapen and will no longer be usable.

• MDs designed for use with data cannot be

used. Please use MDs designed for music.

• Do not use lens cleaners. Doing so will lead

to breakdown.

— 5 —

General features

Power

You can help prevent theft of the unit by reversing the

faceplate so that the control panel cannot be seen, hiding the

unit, and shutting off the audio.

EJECT

SRC/

Egnlish

u/d

4/¢

PWR OFF

Power ON/OFF:

When you turn your vehicle’s ignition on, the unit’s power will

also turn on, with the faceplate reversing to show the control

panel.

KMD-PS971R

4.5V

PREOUT

When you turn your vehicle's ignition off, the faceplate will

reverse to hide the control panel after a period of time which

you have set in the "Time setting for removing the faceplate" in

the menu. The unit's power will turn off.

Alternatively, you can remove the faceplate during that period.

For details, refer to the "Removing the faceplate" (page 14).

NOTE

ATT/

LOUD

#1~6

DISP

AUD AM/ CLK/

NF D.M

• After installation of your Mask unit, be sure to transmit the

"Mask Key's" signal to deactivate the demonstration mode.

If this procedure is not carried out, the control panel of the unit

will re-open in two seconds even with your vehicle's ignition

turned off.

Full-screen display mode

• When the control panel of the faceplate is hidden, the unit will

be locked by the sleeve, making it more difficult to remove the

unit.

• When the moving faceplate is hit by an object, it will stop and

return to its original state. Remove the object and repeat the

action.

Vertical division display mode

Horizontal division display mode

2CAUTION

Using the Unit in Vehicles with Covered Consoles

• Make sure the console is uncovered whilst the faceplate is

reversed.

• Do not exert any excess force on the movable parts of the unit,

including the faceplate, as it can cause failure in the unit’s

mechanism.

Switching Modes

LOUD indicator

Switching Modes:

— 6 —

Each time you press the SRC button, the mode switches as

follows:

Volume

Increasing Volume:

▼

Press the u button to turn up the volume.

Tuner mode

▼

Decreasing Volume:

MD mode

Press the d button to turn down the volume.

▼

External disc control mode 1

▼

External disc control mode 2/AUX mode

▼

Attenuator

Standby mode

This function allows you to turn down the volume quickly.

Selecting the standby mode:

Turning Attenuator On/Off:

Press the SRC button repeatedly to select to "ALL OFF" .

When "ALL OFF" is displayed, the standby mode is turned on.

The standby mode turns all functions off although leaving the

unit’s power on. Use this mode when you want to have the

display illuminated but do not want to listen to anything.

Press the ATT button to switch the attenuator on and off.

When the attenuator is off, the volume returns to the original

level.

NOTE

Turning the volume up, or turning it all the way down deactivates

the attenuator function.

NOTE

• The mode switches to the next mode from any mode which

cannot be used.

• The external disc control mode will differ depending on the unit

that is connected.

• The AUX mode is available only when the changer / AUX

switching adapter (KCA-S210A or CA-C1AX) or CD changer

(KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is

connected to this unit.

During the AUX mode, "AUX" / AUX-name will show in the

display. When the CA-C1AX is being used, the AUX Mode will

replace the External Disc Control Mode.

Loudness

This function amplifies low and high tones when the volume is

turned down.

The LOUD indicator lights up, when the loudness function is

on.

Turning Loudness On/Off:

Hold down the LOUD button for one second or more to switch

the loudness on and off.

NOTE

Presetting AUX-name

In the AUX mode, press the NAME.S button for two seconds or

more. "NAME SET" is display and AUX-name mode is entered.

Input the characters, referring to the section on "Presetting Disc

Names (DNPS)" (page 28).

NOTE

The loudness function does not affect non-fading pre-out.

— 7 —

General features

Audio Control Setting

Adjust various parameters of sound quality.

"Bass Frq" : Adjust the centre frequency of the bass.

Setting values: 60 / 70 / 80 / 100 (Only when the bass quality

factor is set to 1.00, 1.25 or 1.50) / 150 (Only when the bass

quality factor is set to 2.00) Hz

Press the AUD button to enter the control mode.

Egnlish

Selecting mode

NOTE

Press either the FM or AM button.

Each time the button is pressed, the adjustment mode will

change.

Please refer to the following for the contents of the

adjustment modes.

This mode is available only when the Sound coordinate system is

on. (page 35)

NOTE

Source tone memory

Each source (CD, MD, FM, AM, and disc changer) has its own

memory in which to store the bass, treble and N-F level settings.

The settings made for a particular source are then recalled

automatically whenever you use that source (e.g., FM mode uses

the tone settings made for FM, AM for AM, etc.).

"Bass" : Adjust the bass level.

Setting values: - 8 – + 8

Adjust each mode

"Bass Q" : Adjust the Bass quality factor.

Press the 4/¢ button.

Setting values: 1.00 / 1.25 / 1.50 / 2.00

Look at the table to adjust the mode being displayed.

NOTE

Press the AUD button to end the control mode.

This mode is available only when the Sound coordinate system is

on. (page 35)

"dB" : Recalling the kenwood preset sound setting

Press the preset buttons (#1-6).

Settings: #1;Flat, #2;Rock, #3;Pops/Top40, #4;Jazz, #5;Easy,

#6;Scan of #1-5

"Bass EXT" : Switch the Bass Extend mode on/off.

Setting values: ON / OFF

(When the bass extend mode is set to on, low

frequency response is extended by 20%.)

NOTE

• This mode is available only when the Sound coordinate system

is on. (page 35)

NOTE

• You can call the following settings with this function; bass

centre frequency, bass level, bass quality factor, bass

extension, treble centre frequency, and treble level setting.

Their setting values are different depending on the setting of

the mobile preset plan mode.

This mode is available only when the Sound coordinate system is

on. (page 35)

— 8 —

"Tre Frq" : Adjust the centre frequency of the treble.

"HPF Front" : Adjust the frequency of the High-pass filter for

front output.

Setting values: 10.0 / 12.5 / 15.0 / 17.5 kHz

Setting values: Through / 40Hz / 60Hz / 80Hz / 100Hz / 120Hz /

NOTE

150Hz / 180Hz / 220Hz

This mode is available only when the Sound coordinate system is

on. (page 35).

NOTE

You can separately set the high-pass filter for front and rear

output, including preouts. The high-pass filter does not affect the

non-fading preout. The factory default settings for front output

and rear output are "Through" .

"Tre" : Adjust the treble level.

Setting values: - 8 – + 8

"HPF Rear" : Adjust the frequency of the High-pass filter for rear

output.

"Balance" : Adjust the balance level.

Setting values: Through / 40Hz / 60Hz / 80Hz / 100Hz / 120Hz /

150Hz / 180Hz / 220Hz

Setting values: Left 15 – Right 15

NOTE

You can separately set the high-pass filter for front and rear

output, including preouts. The high-pass filter does not affect the

non-fading preout. The factory default settings for front output

and rear output are "Through" .

"Fader" : Adjust the fader level.

Setting values: Front 15 – Rear 15

"LPF NFpre" : Adjust the frequency of the Low-pass filter for

Non-Fading output.

"NFpre Level" : Adjust the Non-fading output level.

Setting values: - 15 – + 15

Setting values: 50 Hz / 80 Hz / 120 Hz / Through

NOTE

Not available during the Dual zone system is on.

— 9 —

General features

Mobile Preset

This function allows you to adjust the setting that is recalled

with the sound coordinate system, according to types of

speakers.

"NFpre Phase" : Adjust the phase for Non-Fading output.

Setting values: Normal (0°) / Reverse (180°)

NOTE

Egnlish

Not available during the Dual zone system is on.

Press the SRC button repeatedly to select the standby mode.

"ALL OFF" is displayed when the standby mode is selected.

Press the AUD button to enter the mobile preset plan mode.

Press either the 4 or ¢ button to select the type of

speaker. The setting switches as follows.

Off / For the OEM speaker / For 6/6x9 in. speaker /

For 5/4 in. speaker

"VOL OFFSET" : Set the sound level of the each source selected

by adjusting the level difference between the

basic sound level and the required level.

Setting values: - 8 – 0

Press the AUD button to end the mobile preset plan mode.

NOTE

• This mode is available only when the Sound coordinate system

is on. (page 35)

• When you change the setting of type of speaker, the bass and

treble tone settings are returned to original levels.

Storing your sound settings:

Hold down a preset button (#1-6) for two seconds or more.

NOTE

• This setting can be made only when the Sound coordinate

system is on. (page 35).

• The settings you can preset are, bass centre frequency, bass

level, bass quality factor, bass extension, treble centre

frequency, and treble level.

Non-Fading Output

Turning non-fading output On/Off :

Hold down the NF button for one second or more to set the

function ON or OFF.

"NF ON" is displayed when the non-fading output is set ON.

Recalling your sound settings:

Press a preset button (#1-6) except during the bass center

frequency, bass level, bass quality factor, bass extension,

treble center frequency, and treble level adjust mode.

TEL Mute

Shut down the audio system temporarily whenever an

incoming call is received.

NOTE

This mode is available only when the Sound coordinate system is

on. (page 35).

NOTE

The function will not work if a cable is not connected to the car

phone.

— 10 —

When the telephone rings:

When a call is received, "CALL" is displayed and all the unit

functions are temporarily interrupted.

Restoring Original Unit Source During Phone Call:

Press the SRC button.

"CALL" disappears from the display, and the volume of the

original source is restored gradually.

Turning TEL Mute Function Off After Phone Call:

Hang the phone up.

"CALL" disappears from the display.

The original source (i.e., the one used before the phone call) is

returned to automatically, and the volume restored gradually.

— 11 —

General features

Example: Tuner mode

Switching Display

You can change the display in each mode.

Left side display

CLK button

Right side display

DISP button

Selecting the Display Mode:

Egnlish

Programme Service name/

Station frequency

Each time you hold down the D.M button for one second or

more, the display mode switches as follows:

Graphic

Band display

+ Preset station number

Spectrum Analyzer1

Spectrum Analyzer2

Spectrum Analyzer3

Analog clock

Vertical division display mode

Horizontal division display mode

Full-screen display mode

Changing the Display:

Digital clock

• During full-screen display mode

Each time you press the CLK button, the display switches as

follows:

NOTE

• This function cannot be operated whilst the Black Mask

function is on.

• The right side display items vary depending on the source

that is playing. For details refer to the "Switching Display"

page for source modes.

Character

"ALL OFF"

Character

Spectrum Analyzer1

Spectrum Analyzer2

Spectrum Analyzer3

Date + Clock

• During vertical division mode display

The upper part display is switched each time the DISP button

is pressed.

The lower part display is switched each time the CLK button is

pressed.

(Source mode)

(Standby mode)

NOTE

Example: Tuner mode

• This function cannot be operated whilst the Black Mask

function is on.

• Character items are not displayed when the graphic display

function is turned off.

Upper part display

DISP button

Lower part display

CLK button

• During horizontal division mode

The left side display is switched each time the CLK button is

pressed.

The right side display is switched each time the DISP button is

pressed.

— 12 —

Programme Service name/

Station frequency

Radio text

Spectrum Analyzer1

Radio text

Spectrum Analyzer2

+ Clock

0 1 2

Spectrum Analyzer2

+ Graphic

Graphic + Clock

Date

NOTE

• Firmly slide the switch until it clicks.

• Do not apply excessive force to the faceplate under settings 1

NOTE

or 2.

• The display items vary depending on the source that is

playing. For details refer to the "Switching Display" page for

source modes.

• The same items cannot be selected for both the upper part

and the lower part.

• When the Black Mask function is turned on, the lower part

display shows the clock only.

• Set the angle adjustment switch to "0" before removing the

faceplate.

Faceplate Angle Adjustment

You can adjust the faceplate angle for easy viewing.

Adjusting faceplate angle:

Press the ¡ (EJECT) button to make the faceplate slide open,

and then adjust the faceplate angle using the angle adjustment

switch.

Adjustment may be made from 0 to 2.

— 13 —

General features

• When removing the faceplate, pull it out only when it is fully

open. The detachment of the faceplate whilst it is moving might

result in damage to the unit.

• Do not apply excessive force to the faceplate bracket without

attaching the faceplate. Doing so will cause the faceplate

bracket to be deformed.

• Do not touch the connector on the faceplate bracket after

removing the faceplate. Touching the connector may cause

damage to the unit.

• Do not touch two metal parts on both sides of the faceplate

bracket. Touching those parts may injure you.

Removing the Faceplate

The faceplate can be detached from the unit, helping to deter

theft.

Egnlish

Removing the faceplate:

Choose the way from among the following and open the

faceplate.

Turn the ignition off, hold down the SRC button for one second

or more, or press the left part at the upper side of the

faceplate (as illustrated on p.15) for as many times as you have

preset in the "Manual Open Button Setting" (OPEN SW #) in

the menu when the control panel has been hidden.

NOTE

• Sliding the faceplate lock switch cause the unit’s power to turn

off. If you want to operate the unit again, remove the faceplate

from the faceplate bracket completely and then reattach it.

• The faceplate is a precision piece of equipment and can be

damaged by shocks or jolts. For that reason, keep the faceplate

in its special storage case whilst detached.

Set the faceplate's angle adjustment switch to "0" to set the

faceplate angle to the vertical.

For details, refer to "Faceplate Angle Adjustment" (page 13).

NOTE

If the faceplate's angle adjustment switch is not set to "0" when

mounting the faceplate on the faceplate bracket, it may be

difficult to mount the faceplate or the faceplate may not be

securely attached and could fall off.

Set the angle adjustment switch to "0" before removing the

faceplate.

• Do not expose the faceplate or its storage case to direct

sunlight or excessive heat or humidity. Also avoid places with

too much dust or the possibility of water splashing.

Slide the faceplate lock switch to the left during the period

which you have set in the "Time setting for removing the

faceplate" in the menu.

Reattaching the Faceplate:

Hold the faceplate so that the control panel faces the front

toward you and set the left side of the faceplate in the

faceplate bracket.

2CAUTION

Do not set the right side of the faceplate in the faceplate bracket

first, when reattaching the faceplate. Doing so may cause the

connector on the faceplate bracket to malfunction.

Faceplate lock switch

Press the right side of the faceplate until it locks.

Holding the centre part of the faceplate, pull it out.

The faceplate bracket will automatically close.

2CAUTION

— 14 —

order to open it. You can prevent tampering of the unit when

letting someone else drive your car by keeping it closed this

way.

To cancel the forced closing of unit and open control panel:

Press the left part at the upper side of the faceplate for as

many times as you have preset in the "Manual Open Button

Setting" (OPEN SW #) in the menu. The faceplate will open and

show the control panel.

NOTE

If the faceplate bracket's angle was not set to the vertical when

the faceplate was mounted, check that the faceplate is securely

attached to the faceplate bracket by holding its right side and

pulling it gently towards you.

NOTE

When you set the Manual Open Button setting to 2 or 3, press

the upper left part of the faceplate without pausing. If you do not

press that part without pausing, the command cannot be verified

correctly.

Forced Closing

This function prevents tampering with the unit your car is

being serviced etc.

Hiding the unit with the ignition turned on (forced closing):

Hold down the SRC button for one second or more.

The faceplate will slide open. When the period of time which

you have set in the "Time setting for removing the faceplate" in

the menu has passed, the faceplate automatically reverses to

hide the control panel. However, you can remove the faceplate

during that period. For details, refer to the "Removing the

faceplate" (page 14).

NOTE

• When the closing faceplate is hit by an object, the unit will turn

off without the faceplate closing all the way. Remove the object

and press the SRC button to turn the unit back on, then turn it

off again to make it close properly.

• Whilst the control panel is moving, pressing the buttons will not

have any effect. Do not try to press the buttons on the control

panel as the faceplate is moving, as excessive force may

damage the unit.

• During the forced closing of the unit (i.e., having the unit left

closed whilst ignition is turned on), the faceplate will not open

no matter how often the ignition is turned on or off, unless

"Manual Open button" at the rear of the faceplate is pressed in

— 15 —

Tuner features

Tuning

Press the SRC button repeatedly until the tuner mode is

obtained. "TUNER" is displayed only when the tuner mode is

selected.

Egnlish

4/¢

FM/AM

38 SRC

Press either the FM or AM button to select the band.

Each time you press the FM button, the band switches

between the FM1, FM2 and FM3.

KMD-PS971R

4.5V

PREOUT

Press the AM button to select the MW and LW bands.

• Auto Seek Tuning

Press the ¢ button to seek increasing frequencies.

Press the 4 button to seek decreasing frequencies.

• Preset station seek tuning

Press the ¢ button to move to the next preset station (i.e.,

the one with the next highest number), and the 4 button to

move to the last preset station (i.e., the one with the next

lowest number).

#1~6

DISP

CLK

NOTE

If the frequencies stored at the preset numbers receive

stations which were not originally memorized when traveling

long distances, the preset number is not displayed. In such

cases, pressing the 4/¢ button to use preset station

seek will receive channel 1.

Preset station number

Band display

Frequency

• Manual Tuning

Press the ¢ button to increase the frequency by one step.

Press the 4 button to decrease the frequency by one step.

NOTE

• The ST indicator lights up when stereo broadcasts are being

received.

• Please see the menu settings about selecting tuning mode.

(page 36)

AUTO indicator

Switching Display for Tuner

ST indicator

You can change the display used when listening to the radio.

Changing the Display:

— 16 —

Pressing the DISP button or CLK button, the display switches

as follows:

• During vertical division mode display

Programme Service name/

Station frequency

Graphic

Band display

+ Preset station number

Spectrum Analyzer1

Spectrum Analyzer2

Spectrum Analyzer3

Analog clock

Upper part display

Lower part display

DISP button

CLK button

Programme Service name/

Station frequency

Radio text

Spectrum Analyzer1

Radio text

Spectrum Analyzer2

+ Clock

Digital clock

Spectrum Analyzer2

+ Graphic

NOTE

This function cannot be operated whilst the Black Mask

function is on.

Graphic + Clock

Date

• During the full-screen display mode

The display is switched each time the CLK button is pressed.

NOTE

For information regarding the display items, refer to "Switching

Display" (page 12).

• The same items cannot be selected for both the upper part

and the lower part.

• When the Black Mask function is turned on, the lower part

display shows the clock only.

Displaying Frequencies:

Hold down the DISP button for one second or more.

The frequency for the RDS station will be displayed for five

seconds instead of the station name.

• During horizontal division mode

Left side display

CLK button

Right side display

DISP button

NOTE

• Programme Service name / Radio text : only during RDS station

reception.

• If the RDS station currently tuned to is transmitting no text

whilst the Radio Text Display mode is turned on, "NO TEXT" will

appear in the display. Whilst awaiting reception, "WAITING" will

be displayed.

2WARNING

To prevent accidents, drivers should not look at the display whilst

on the road.

— 17 —

Tuner features

RDS features

Station Preset Memory

Store the frequency of the station currently being listened to.

You can then recall that station with a single touch of a button.

Egnlish

4/¢

FM/AM

PTY SRC

Select the band/ station that you want to have stored.

Hold down the button (#1-6) that you want to use for the

station, for two seconds or more.

The button number blinks once in the display to indicate that

the data has been stored.

KMD-PS971R

4.5V

PREOUT

Recalling a Preset Station:

Press the preset station button (#1-6) for the desired station.

The number of the recalled station is displayed.

NOTE

You can store 6 stations in each of the FM1, FM2, FM3, and AM

(MW and LW) bands.

#1~6

TI/

VOL ADJ

DISP

CLK

Radio text

Kenwood intelligent Twin IF (K2I)

Programme Servics name

When the frequency of another station is too close to that of

the station currently being listened to, interfering with proper

reception, this function automatically narrows the range of

received frequencies to prevent such interference.

NEWS indicator

RDS indicator

TI indicator

— 18 —

RDS (Radio Data System)

Traffic Information Function

You can listen to traffic information. If you are listening to

tapes or discs, they will continue playing until a traffic bulletin

is broadcast.

RDS is a digital information system that lets you receive

signals besides those of regular radio programmes, such as

network information being transmitted from radio stations.

When listening to an RDS station (ie, a station with RDS

capability), the programme service name of the station is

displayed along with the frequency, advising you quickly which

station is being received.

RDS (Radio Data System) stations also transmit frequency data

for the same station. When you are making long trips, this

function automatically switches to the particular frequency

with the best reception for the particular network of stations

that you want to listen to. The data is automatically stored,

allowing you to switch quickly to another RDS stations,

broadcasting the same programme, that has better reception.

These include stations stored in the station preset memory that

you often listen to.

Turning TI function On/Off:

Press the TI button to turn the function on and off.

When the function is on, the TI indicator is turned on.

When none is being received, the TI indicator will blink on and

off. When a traffic information station is being received, the TI

indicator will turn on.

When a traffic bulletin begins to be broadcast, "TRAFFIC INFO"

will be displayed, and reception will begin at the preset

volume.

If you are listening to a tape or disc when a traffic bulletin

begins, they will automatically be turned off. When the bulletin

ends or poor reception is experienced, the tape or disc will

begin playing again.

NOTE

Pressing the TI button whilst in the MW/LW band automatically

switches reception to the FM band. However, the MW/LW band

is not returned to when the TI button is pressed again.

Enhanced Other Network

Stations that offer <Enhanced Other Network> also transmit

information about other RDS stations that have traffic

information. When you are tuned to a station that is not

transmitting traffic information, but another RDS station starts

transmitting a traffic bulletin, the tuner automatically switches

to the other station for the duration of the bulletin.

Switching to a Different Traffic Information Station:

Use the 4 / ¢ buttons to make an auto seek of the TI

stations in a certain band.

NOTE

• When you are listening to a tape or disc, you cannot change to

another TI station.

• When the auto TP seek function is turned on and reception

starts to weaken, the tuner automatically seeks traffic

information stations with better reception.

• If you are tuned to a station that is not a traffic information

station itself but which provides <Enhanced Other Network>

services, you can still have traffic information received.

• Holding the TI button down for one second or more when the

TI function is on in the disc control mode results in a change to

the frequency display of the traffic information station for five

seconds.

Alarm

When an emergency transmission (announcing disasters, etc.)

is sent, all current functions are interrupted to allow the

warning to be received.

— 19 —

RDS features

Presetting Volume for Traffic Information/News

Preset the volume level to be used for traffic information and

news broadcasts.

Select the type of programme to be received

• Press either the FM or AM buttons repeatedly until the type

of programme you want to listen to.

The selection includes:

Egnlish

Tune into the station for which you want to set the volume.

Adjust the volume to the desired level.

Speech

(All Speech)

(All Music)

(News)

Music

1. News

Hold down the VOL ADJ button for two seconds or more.

The volume level blinks once in the display to indicate that the

data has been stored.

Future traffic information/news broadcasts are heard at the

preset level.

2. Current Affairs

3. Information

4. Sports

(Current Affairs)

(Information)

(Sport)

5. Education

6. Drama

(Education)

(Drama)

7. Culture

(Cultures)

NOTE

8. Science

(Science)

• The volume cannot be lowered by this function during tuner

reception. The volume is only set when it is louder than the

listening volume of the tuner.

• You can arrange only to listen to traffic information or news

bulletins with at preset volume with the volume set at

minimum.

9. Varied

(Varied Speech)

(Pop Music)

(Rock Music)

(Easy Listening)

(Light Classics M)

(Serious Classics)

(Other Music)

(Weather& Metr)

(Finance)

10. Pop Music

11. Rock Music

12. Easy Listening Music

13. Light Classical

14. Serious Classical

15. Other Music

16. Weather

17. Finance

Programme Type (PTY) Function

Conduct auto seek tuning only on those stations with selected

kinds of programmes.

18. Children’s programmes (Children's Progs)

19. Social Affairs

20. Religion

(Social Affairs)

(Religion)

(Phone In)

(Travel & Touring)

(Leisure & Hobby)

(Jazz Music)

21. Phone In

Press the 38(PTY) button.

22. Travel

"PTY" is displayed, and the Programme Type Selection (PTY)

Mode entered.

23. Leisure

24. Jazz Music

25. Country Music

26. National Music

27. Oldies Music

28. Folk Music

29. Documentary

If you make no key input in 30 seconds, the mode will

automatically turn off.

(Country Music)

(National Music)

(Oldies Music)

(Folk Music)

NOTE

You cannot use this function whilst the traffic bulletin is received.

(Documentary)

NOTE

Changing the Display Language to French, German, or Swedish

(Speech.....1~9,16~23, 29, Music.....10~15, 24~28)

• You can select the type of programme directly by pressing a

preset button. The buttons are factory-set to the following

type of programmes:

In the PTY mode, press the DISP button to display the name of

the language currently used.

If you want to change the language, press the preset button for

the desired language and then the DISP button.

1. Music

4. Other Music

2. Speech

5. Serious Classical

3. News

6. Varied

English is #1, French is #2, German is #3, and Swedish is #4.

— 20 —

To scroll automatically:

NOTE

Changing the Preset Button Settings for Programme Type

Press the DISP button to display the Radio Text.

After selecting the type of programme to be stored in a certain

preset button, hold down that button for two seconds or more.

The previously stored data for that button are erased and the

new programme type is stored.

The text will be displayed in one scrolling display.

Press the DISP or CLK button to change the upper part of the

display to radio text.

Seeking the selected programme type

Holding down the DISP button for one second or more results

in one scrolling display of the text.

Press the 4 or ¢ button to make a seek of frequencies

with your selected type of programme.

The display blinks and the seek starts.

NOTE

Please see the menu settings (page 38) about switching between

manual scrolling and automatic scrolling.

"PTY" blinks in the display for about 30 seconds.

If you make no key input in 30 seconds, the PTY selection

mode will turn off automatically.

NOTE

If no programme can be found, "NO PTY" is displayed.

If you want to select another type of programme, repeat steps 2

and 3 above.

Switching to Other Stations with the Same Type of Programme:

When "PTY" is blinking in the display, perform auto seek

tuning.

The tuner scans for another station with the same type of

programme.

Cancelling Programme Type Function During Its Operation:

Press the 38(PTY) button.

Radio Text Scroll

This function permits the text to be scrolled and the entire text

to be displayed. The scrolling method differs depending on the

setting of scrolling in the menu.

To scroll manually:

Press the DISP or CLK button to change the upper part of the

display to radio text.

Holding down the DISP button for one second or more results

in one scrolling display of the text.

— 21 —

MD/External disc control features

When a unit equipped with an O-N switch is to be connected,

please also see the instruction manual of this unit.

Set the O-N switch to "N". "N"-operation will be set.

EJECT

DISC+/

DISC-

"N"-operation:

Egnlish

4/¢

SRC

• The disc title and track title of the CD text can be displayed.

• The disc name will be displayed when the name has been

registered to any connected unit with the Presetting Disc

Names function, or when the playing unit contains a disc to

which the disc title has been recorded.

KMD-PS971R

4.5V

PREOUT

"O"-operation:

• CD text cannot be displayed.

• Regardless of the control unit, the characters that can be

registered with the Presetting Disc Names function are "A~Z

0~9 /, +, –, ∗, =, <, >, [ , ]".

• The disc name will be displayed when the name has been

registered to the playing unit with the Presetting Disc Names

function.

SCAN

REP

M.RDM

D.SCN

DISP

NAME.S

CLK

RDM

NOTE

The CD text, Presetting Disc Names, and Disc Name Preset Play

functions may not be operational depending on the unit.

Track number

Track time

Playing MDs

Playing MDs:

Disc title/Track title/DNPS

Press the ¡(EJECT) button to slide open the faceplate,

showing the MD (insertion) slot. Insert the MD in the proper

orientation.

The faceplate will close, and the MD will start playing.

The •••(MD-IN) indicator will light when an MD has been

inserted.

Playing MDs Already Inserted:

Press the SRC button repeatedly until the MD mode is

obtained. "MD" is displayed when the MD mode has been

selected.

•••(MD-IN) indicator

The MD will start playing.

— 22 —

Pausing and Restarting MD Play:

Pausing and Restarting Disc Play:

Press the 38 button to make the disc pause.

Press the same button again to start play again.

NOTE

Eject:

Press the ¡(EJECT) button. The faceplate will slide to eject

the MD.

When one disc has finished playing its last track, the next disc in

the changer will start playing. When the last disc in the changer

has finished, the player will return to the first disc and start

playing it.

Press the ¡(EJECT) button to close the faceplate.

2CAUTION

• Do not attempt to insert an MD into the slot if another one is

already there.

• When the faceplate has been slid open, it might interfere with

the gear lever or something else. If this happens, pay attention

to safety and move the gear lever or take an appropriate action,

then operate the unit.

Fast Forwarding and Reversing Disc Play

Fast Forwarding Disc Play:

Hold down on the ¢ button.

NOTE

Release your finger to play the disc at that point.

• The sound will be temporarily muted whilst the faceplate is

moving.

• The only buttons that will work during the eject state are the

¡(EJECT), SRC, TI, and ATT buttons, as well as the volume

control button.

Reversing Disc Play:

Hold down on the 4 button.

Release your finger to play the disc at the point.

NOTE

You cannot use reverse play between tracks depending on the

model being connected. Instead, the reverse play function is

cancelled when it reaches the beginning of a track, at which

point normal play automatically resumes.

Playing Other Disc mode

This function permits the connection of optional players and

the playing of discs other than the loaded MD (in the current

unit).

Playing Discs:

Press the SRC button repeatedly to select the external disc

control mode.

The disc will start playing.

NOTE

The external disc control mode will differ, depending on the unit

that is connected.

Mode Display Examples

• "CD" ...when a CD player is connected

• "DISC" ...when a disc changer is connected

• "DISC-1" , "DISC-2" ...when two disc changers are connected

— 23 —

MD/External disc control features

Play starts at the beginning of the displayed disc.

NOTE

Track Search

Search forwards or backwards through the tracks on the disc

until you reach the one that you want to listen to.

"LOAD" is displayed when discs are being exchanged on the disc

changer.

Egnlish

Making a Reverse Track Search:

Press the 4 button to display the desired track number.

Press once to search back to the beginning of the current

track, twice to search back to the beginning of the previous

track, and so forth.

Switching Display for Discs

Switch the display that appears whilst discs are playing.

Play starts at the beginning of the displayed track number.

NOTE

(For disc changers)

Switching Display for Discs:

Pressing the 4 button whilst listening to track 1 only searches

back to the beginning of that track. The reverse search is not

"recycled" to the last track on the disc.

Each time you press the DISP button or CLK button, the

display during disc play switches as follows:

• During vertical division mode display

Making a Forward Track Search:

Upper part display

DISP button

Lower part display

CLK button

Press the ¢ button to display the desired track number.

Press once to fast forward to the next track, twice to fast

forward to the track after that, and so forth.

DNPS

Track Time

DNPS

Play starts at the beginning of the displayed track number.

NOTE

Disc Title

(For disc changers)

You cannot make a forward track search when listening to the

last track on a disc.

Disc Title

Track Title

Spectrum Analyzer1

Track Title

Spectrum Analyzer2

+ Clock

Disc Search

Search forwards or backwards through the discs in a disc

changer until you reach the one that you want to listen to.

(Function of disc changers)

Spectrum Analyzer2

+ Graphic

Graphic + Clock

Date

Making a Reverse Disc Search:

Press the DISC– button to display the desired disc number.

Each time the button is pressed, the displayed disc number

decreases by one.

Play starts at the beginning of the displayed disc.

NOTE

• The same items cannot be selected for both the upper part

and the lower part.

• When the Black Mask function is turned on, the lower part

display shows the clock only.

Making a Forward Disc Search:

Press the DISC+ button to display the desired disc number.

Each time the button is pressed, the displayed disc number

increases by one.

— 24 —

• During horizontal division mode

Left side display

CLK button

Right side display

DISP button

Graphic

Track number

Track Time

Spectrum Analyzer1

Spectrum Analyzer2

Spectrum Analyzer3

Analog clock

DNPS

Track Time

Track number

DNPS

Digital clock

NOTE

This function cannot be operated whilst the Black Mask

function is on.

• During the full-screen display mode

The display is switched each time the CLK button is pressed.

NOTE

For information regarding the display items, refer to "Switching

Display" (page 12).

NOTE

• DNPS : function of disc changers.

• You can give names to discs through the presetting disc name

function (page.28).

Note that depending on the unit, display may not be possible.

• If you try to display the name of a disc that does not have one,

"NO NAME" is displayed instead.

• When an attempt is made to display the title of a disc for which

a disc title/track title has not been recorded, the CD will display

"NO TEXT" , the MD player built into this unit will display "NO

TITLE" , and an MD changer will display "NO TITLE/NO NAME".

• Depending on the type of characters of the CD Text, some

characters may not be displayable.

— 25 —

MD/External disc control features

Track / Disc Repeat

Repeat playing the current track or disc.

Disc Scan

(Function of disc changers)

Successively play the beginning of each disc on a changer

until you find the one that you want to listen to.

Turning Repeat Play Function On/Off:

Press the REP button to switch the repeat play function on and

off as follows :

Egnlish

Starting the disc scan:

Press the D.SCN button. "Disc Scan ON" is displayed and the

first 10 seconds of each disc are played, in the order in which

they are loaded on the changer.

▼

Track Repeat ON

The disc number currently being heard blinks in the display.

▼

Stopping to Listen to the Disc Being Scanned:

Press the 38 or D.SCN button again to stop the scan and keep

on listening to the disc normally.

Disc Repeat ON (Function of disc changers)

▼

Track/Disc Repeat OFF

NOTE

"Track Repeat/T-Repeat/Repeat ON" is displayed and the track

number blinks in the display when track repeat is on.

"Disc Repeat/D-Repeat ON" is displayed and the disc number

blinks in the display when disc repeat is on.

• The disc scan function is cancelled when you eject the disc.

• The disc scan function only scans each disc on the changer

once.

• "LOAD" is displayed when discs are being exchanged on the

disc changer.

NOTE

Repeat play is cancelled when you eject the disc.

Random Play

Play all the tracks on the current disc in random order.

Track Scan

Successively play the beginning of each track on a disc until

you find the track that you want to listen to.

Press the RDM button to switch the random play function on

and off.

Starting the Track Scan:

"Random ON" is displayed when random play is turned on.

The display of the track number changes continuously as the

next track is being selected.

Press the SCAN button. "Track Scan/Scan ON" is displayed and

the first 10 seconds of each track are played, and the tracks

are played in order.

When the track has been selected, play starts.

The selected track number blinks in the display as it is being

played.

The track number currently being heard blinks in the display.

Stopping to Listen to the Track Being Scanned:

Press the 38 or SCAN button again to stop the scan and keep

on listening to a track normally.

NOTE

(For disc changers)

When all the tracks on a certain disc have been played using the

random play function, the next disc on the changer starts playing

(with the random play function still turned on).

NOTE

• The track scan function is cancelled when you eject the disc.

• The track scan function only scans each track on a disc once.

To change the track being heard, press the ¢ button.

Another track is selected and played.

— 26 —

NOTE

Press the DISP or CLK button to display the disc title or track

title at the upper part of the display.

Random play is cancelled when you eject the disc.

Holding down the DISP button for one second or more results

in one scrolling display of the titles.

To scroll automatically:

Press the DISP button to display the disc title or the track title.

The titles will be displayed in one scrolling display.

Magazine Random Play

(Function of disc changers)

Play the tracks on all the discs in the disc changer in random

order.

NOTE

When the disc or track to be played changes, the title is

displayed in one scrolling display.

Press the M.RDM button to switch the magazine random play

function on and off.

Press the DISP or CLK button to display the disc title or track

title at the upper part of the display.

"M-Random ON" is displayed when magazine random play is

turned on.

Holding down the DISP button for one second or more results

in one scrolling display of the titles.

The display of the disc and track numbers change continuously

as the next track is being selected.

When the disc/track has been selected, play starts.

The selected disc/track number blinks in the display as it is

being played.

NOTE

Please see the menu settings (page 38) about switching between

manual scrolling and automatic scrolling.

NOTE

This function is not available with the following models:

KDC-C200/C300/C400/C301/C401

To change the track being heard, press the ¢ button.

Another disc/track is selected and played.

NOTE

• Magazine random play is cancelled when you eject the disc.

• The time needed for random selection depends on the number

of discs loaded in the disc magazine.

Text / Title Scroll

This function permits the text to be scrolled and the entire text

to be displayed. The scrolling method differs depending on the

setting of scrolling in the menu.

To scroll manually:

— 27 —

MD/External disc control features

A press of the 38 button exits the disc name preset mode.

Operations can be followed again from Step 2 at a time such

as this, and the characters to be input are selected using the

procedure described below.

Press the DISC+ or DISC– button to display the desired

character. Besides the alphabet (capital letters only) and

numbers, you can choose the following characters: /, +, –, *,

=, <, >, [ and ].

Presetting Disc Names(DNPS) (Function of disc changers)

Store the names of discs to be displayed when played.

Play the disc whose name you want to preset.

Egnlish

NOTE

• This function is not available for disc changers that do not

feature the Disc Name Preset function.

• This procedure is not to be used to store the disc and track

titles for MDs that you record.

• When the display mode selection is full-screen display and disc

title or track title is displayed at the upper part of the vertical

division screen, the disc name preset function cannot be used.

Continue steps 3 and 4 until all the characters are chosen for

the name.

NOTE

You can enter up to 10 characters for each name.

Press the NAME.S button.

Hold down the NAME.S button for two seconds or more.

The disc name is stored and the disc name preset mode is

cancelled.

"NAME SET" is displayed and the disc name preset mode is

entered.

If you make no entry in a 10-second period, the name will be

stored with the characters input so far.

The cursor blinks in the position where character input can be

made.

NOTE

Press either the 4 or ¢ button to move the cursor to the

desired position.

• The number of characters and discs whose names can be

stored will differ depending on the disc changer that is

connected. Please see your disc changer manual for details.

• Discs are identified by their total length and number of tracks. If

another disc happens to have the same specifications as one

that you have already stored a name for, the name will be

displayed for it, too.

• If you want to change the name of a disc, repeat steps 1 and 2

to display the name, and then repeat steps 3 and 4 to input the

changes.

• Pressing the reset button does not erase the disc names stored

in a disc changer.

The 4 button moves the cursor to the left, and the ¢

button to the right.

Each time the 38 button is pressed, the characters to be

entered change as listed below.

^{Press the DISC}+ or DISC– button to display the desired

character.

Characters that can be displayed are as follows.

Alphabet (upper case): A ~ Z

Alphabet (lower case): a ~ z

Numerals and symbols: 0~9 @ ” ‘ ` % & ∗ + - = , . / \ < > [ ]

Special characters: á

›

NOTE

The operation and characters that can be entered may change

as listed below, depending on the unit that is connected.

— 28 —

Menu settings

4/¢

FM/AM

KMD-PS971R

4.5V

PREOUT

DISP

Menu display

AUTO indicator

RDS indicator

NEWS indicator

— 29 —

Menu settings

If you fail to end the menu mode, several functions may not

operate properly, including the Traffic Information function, the

News Bulletin function with PTY news timeout setting, and the

Alarm function.

Menu System

You can set the defaults for additional functions in the menu

mode.

Make a setting for each function, referring to the following

operations.

Egnlish

Enter the menu mode

Hold down the MENU button for one second or more.

"MENU" is displayed when the menu mode is entered.

The function that you can adjust is indicated with the current

settings displayed.

Touch Sensor Tone

This function produces a beep sound that accompanies button

operation. It can be switched on or off.

Display and setting:

Selecting function to set

"Beep ON" : Beep setting is on.

"Beep OFF" : Beep setting is off.

Press the FM button to search through the functions until you

see the one you want to adjust in the display.

Press the AM button to search through the functions backward.

Example: If you want to switch the tuning mode from AUTO1

to manual, first search through the functions until

you see "Auto 1" in the display.

NOTE

The beep sound is not output from the preout jacks.

Manual Time Adjustment

Adjust the time manually.

NOTE

Changing setting for currently displayed function

Press either the 4 or ¢ button.

This adjustment is available only when the automatic time

adjustment is set to off. (page 32)

The setting will change for each function.

Example: The tuning mode will switch from AUTO 1 to AUTO

2. Pressing the button again switches the setting to

manual, and "Manual" is displayed.

Display and setting:

Select the display "Clock Adjust" during the selecting function

in the menu system.

Hold down either the 4 or ¢ button for two seconds or

more to enter the Manual time adjustment mode.

The time display will blink.

• Adjusting the hours

Press the FM button to advance the hours, or press the AM

button to make the hours go back.

Ending the menu mode

Press the MENU button.

• Adjusting the minutes

NOTE

Press the ¢ button to advance the minutes, or press the

Make sure to end the menu mode when finished.

4 button to make the minutes go back.

— 30 —

Press the MENU button to end the menu mode.

Calendar Adjustment

Adjust the date for the unit so that you can use the calendar

function.

Display and setting:

Select the display "Date Adjust" during the selecting function in

the menu system.

Hold down either the 4 or ¢ button for two seconds or

more to enter the Calendar adjustment mode.

The date display will blink.

Selecting the item (day, month, or year) to adjust

Press the 4 or ¢ button.

The item blinking in the display can be adjusted.

Adjusting the date

Press the FM or AM button.

The item of the date blinking in the display will change.

Press the MENU button to end the menu mode.

Calendar Mode

You can set the date formats of the calendar function.

Display and setting:

Select the display "Date Mode" during the selecting function in

the menu system.

Press the 4 and ¢ button to select the date format you

want to show in the display.

The sample of the date format for today is displayed.

— 31 —

Menu settings

Memo Mode

You can input the text to be displayed and set the date when

that text will appear in the display with the calendar function.

Alphabet (upper case): A ~ Z

Alphabet (lower case): a ~ z

Egnlish

Display and setting:

Numerals and symbols: 0~9 @ ” ‘ ` % & ∗ + - = , . / \ < > [ ]

Select the display "Memo Mode" during the selecting function

in the menu mode.

Special characters: á

›

Hold down either the 4 or ¢ button for two seconds or

more to enter the Memo mode.

The date display will blink.

• Selecting the character

Press the FM and AM button.

Selecting the set of the date and text to be displayed

Press the FM and AM button.

Press the MENU button to end the menu mode.

NOTE

If you want to input a new text, select the blank display.

• The text you selected automatically appears on the date you set

when the unit’s power is first turned on. (Calendar function)

Pressing the DISP button for one second or more scrolls the

display once, regardless of the text scroll setting.

Entering the month or day setting mode

Press the 4 and ¢ button to enter the month or day

setting mode.

The month display will blink enter the month setting mode, the

day display will blink enter the day setting mode.

Pressing a button other than the DISP button will cause the text

to disappear from the display.

• You can enter up to 32 characters for each text.

• The calendar function can be set up to 30 cases.

• To delete the date and text setting, set both the month and day

of the date to "00" or set all of the text to blanks.

Changing the month or day

Press the FM and AM button.

Entering the text input mode

Press the ¢ button to enter the text input mode.

The cursor blinks in the position where character input can be

made.

Inputting / Changing the text

• Moving the cursor

Automatic Time Adjustment

Press the 4 and ¢ button.

• Changing the type of characters

Press the 38 button.

With automatic time adjustment, you can set the clock time

automatically according to time data sent from RDS stations

(after receiving RDS signals for several minutes). You can also

set the time manually if the automatic time adjustment

function is turned off. The factory default is automatic time

adjustment.

Each time the button is pressed, the type of characters

switches as follows.

Display and setting:

"SYNC ON" : Automatic time adjustment

"SYNC OFF" : Manual time adjustment

Adjusting Time Automatically:

— 32 —

Tune into an RDS station for 3 or 4 minutes.

The time adjusts automatically to the correct local time.

NOTE

Transmission part

Transmit button

The time is not adjusted when the RDS station you are tuned to

is not transmitting a time signal. Choose another RDS station in

such a case.

Mask Key

NOTE

If you have transmitted the Mask Key's signal once to the unit

in advance, you will have to transmit it once again if the unit

has been removed from the battery. This function helps

prevent theft.

• Keep the Mask Key close to the signal sensor when you

transmit the Mask Key’s signal.

• If the Mask Key’s signal does not be received correctly, the

display will return to "TRANSMIT 1" . In this case, repeat the

procedure in step 5.

When using the unit for the first time:

In order to deactivate the demonstration mode, be sure to

press the transmit button to transmit the Mask Key's signal.

If this procedure is not carried out, the control panel of the unit

will re-open in two seconds even with your vehicle's ignition

turned off.

Hold down the transmit button on the Mask key again until the

full transmit level indicator lights up in the display.

"APPROVED" will appear in the display, with the Mask key

function turning on.

If you press the RESET button or remove the battery:

The first time you turn the unit on again, "TRANSMIT 1" will

appear in the display, indicating the setting mode has been

entered. Repeat steps 5 and 6 above, and transmit the signal.

You can start operating the unit again when "APPROVED"

appears in the display.

Press the SRC button repeatedly to select the standby mode.

"ALL OFF" is displayed when the standby mode is selected.

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the FM button repeatedly until the "Mask key" appears in

the display.

Press the AM button to search in the other direction.

Hold down either the 4 or ¢ button for two seconds or

more.

Selectable Illumination

You can switch the colour of the button illumination between

green and red.

"TRANSMIT 1" will appear in the display, indicating the setting

mode has been entered.

Display and setting:

Hold down the transmit button on the Mask key until the full

transmit level indicator lights up in the display.

"TRANSMIT 2" will be displayed.

"Color Green" : The colour of the illumination is green.

"Color Red" : The colour of the illumination is red.

— 33 —

Menu settings

Display and setting:

Brightness level adjustment

You can adjust the brightness level of the unit separately when

your car's light switch has been turned on or off.

"BLACK MASK ON" : The display will be shown in horizontally

divided mode. When this function is

enabled, the dual display mode is entered

and ••• (MD-IN) indicator is displayed.

Clock alone is displayed in the lower part.

"BLACK MASK OFF" : The display will turn on by using the

whole part of the display.

Egnlish

Display and setting:

"Bright 0" – "Bright 10"

NOTE

The initial setting value whilst your car's light switch is turned on

is "5" , and whilst the light is turned off is "10" .

NOTE

This function cannot be set in the full-screen display and

horizontal division display.

Dimmer

You can dim the display.

Time setting for removing the faceplate

You can set the interval during which the open control panel

cannot reverse to be hidden. During the period you have set,

the faceplate can be removed from the faceplate bracket.

NOTE

The dimmer function is not available for units if the dimmer cable

is not connected.

Display and setting:

"Dimmer ON" : The dimmer setting is on.

"Dimmer OFF" : The dimmer setting is off.

"OFF WAIT" : 0sec / 3sec / 5sec / 10sec / 15sec / 20sec /

25sec (sec=sec.)

NOTE

If you do not slide the faceplate lock switch during the period

which you have set, the unit’s power turns off after the control

panel is automatically hidden.

Switching Graphic Display

You can turn the movement of graphic display on and off.

The initial setting is ON.

Dual Zone System

Display and setting:

"Graphic ON" : The graphic display works.

"Graphic OFF" : The graphic display does not work.

The following operation allows separate sound sources to

control the output of the front and rear speakers. The Dual

zone system can only be switched on or off when the source is

set to the AUX mode.

Display and setting:

"Zone 2 ON" : The dual zone system function is on.

"Zone 2 OFF" : The dual zone system function is off.

Black Mask

This function allows you to turn off the graphic part of the

display if there is too much information in the display.

NOTE

— 34 —

• You must purchase the optional KCA-S210A/CA-C1AX/KDC-

CPS82/KDC-CX82/KDC-CPS85/KDC-CX85 device before you can

use this function.

• You can choose to send the AUX input through the rear

channel, and the unit’s tuner or MD source through the front

channel.

• The Bass, Treble and Loudness adjustments do not affect the

rear channel.

• When the Dual zone system is turned on, the External disc

control features cannot be used.

• When you set the Dual zone system to on whilst the non-fading

preout is switched on, the sound of the non-fading preout does

not be outputted.

Manual Open Button Setting

By pressing the button hidden behind the upper left part of the

faceplate during forced closing, you can open the faceplate.

Follow the directions below to preset the number of times that

this button needs to be pressed in order to open the faceplate.

Display and setting:

"OPEN SW 1" – "OPEN SW 3"

NOTE

The initial setting value is "1" .

dB (Sound Coordinate system)

When this system is set to on, the sound coordinate factors

(Bass frequency, Bass quality, Bass extension, and Treble

frequency) appear during the audio control mode.

Display and setting:

"dB set ON" : The sound coordinate factors appear and can be

adjusted.

"dB set OFF" : The sound coordinate factors are not appeared.

External Amp Control

Adjust the bass boost level of the external amplifier using the

main unit.

Display and setting:

"AMP BASS Flat" : Bass boost level is flat.

"AMP BASS +6" : Bass boost level is low (+6dB).

"AMP BASS +12" : Bass boost level is high (+12dB).

NOTE

As of December 1999, the power amplifiers controllable by the

main unit are as follows:

KAC-X501F/PS501F/X401M/PS401M/X301T/PS301T/X201T/PS201T.

— 35 —

Menu settings

Selecting Tuning Mode

News Bulletin Function

You can choose from three tuning modes: auto seek, preset

station seek, and manual. The "AUTO 1" indicator lights up

when auto seek tuning is selected, and the "AUTO 2" indicator

lights when preset station seek tuning is selected.

with PTY News Timeout Setting

You can arrange to have news bulletins interrupt your current

listening source, including other radio stations. When the

News Bulletin function is on, the PTY News Timeout setting

allows you to set the interval during which further news

interruption cannot take place. You can adjust the PTY news

interruption period from 10 to 90 minutes for each journey.

Egnlish

Display and setting:

"Seek Mode Auto 1" : Auto seek tuning mode

"Seek Mode Auto 2" : Preset station seek tuning mode

"Seek Mode Manual" : Manual tuning mode

Display and setting:

"NEWS OFF/ 00min/ 10min/ 20min/ 30min/ 40min/ 50min/

60min/ 70min/ 80min/ 90min"

(min= minutes)

: When you select the news interruption timeout interval, the

News function turns on and the NEWS indicator lights up.

When a news bulletin is received, "NEWS" will be displayed

and reception will begin at the preset volume.

Auto Memory Entry

You can automatically store all the receivable frequencies in

the band currently being listened to, and then recall them with

the touch of a button later. This function is especially useful

when you are travelling and do not know what stations are

available. Up to 6 frequencies can be stored this way.

NOTE

• If you choose the "20min" setting, further news bulletins will not

be received for 20 minutes once the first news bulletin is

received.

• This function is only available if the desired station sends PTY-

code for news bulletin or belongs to <Enhanced Other

Network>-Network sending PTY-code for news bulletin.

• If you turn on the news bulletin function in the MW/LW band,

the band is switched automatically to the FM band.

However, the MW/LW band is not returned to when you turn

off the function.

Display and setting:

Select the display "A-Memory" during the selecting function in

the menu system.

Hold down either the 4 or ¢ button for two seconds or

more to start auto memory function.

The numbers of the preset station buttons showed in order.

When all the stations in a certain band are stored in the preset

memory, the auto memory entry stops. The tuner then plays

the last station received.

NOTE

Local Seek Function

With the local seek function turned on, auto seek tuning skips

stations with relatively poor reception.

• When the AF function is turned on whilst auto memory entry

takes place, only RDS stations (i.e., stations with RDS

capability) are stored. RDS stations that have been preset for

FM1 cannot also be preset in FM2 or FM3.

• When the local seek function is turned whilst auto memory

entry takes place, stations with poor reception are not stored.

• When the Traffic Information function is on , only the local

traffic information station frequency will be stored.

Display and setting:

"Local.S ON" : The local seek function is on.

"Local.S OFF" : The local seek function is off.

Cancelling Auto Memory Entry During Its Operation:

— 36 —

Press the MENU button whilst auto memory entry is taking

place to stop the process.

NOTE

Sometimes stations in the same network broadcast different

programmes or use different programme service names.

Recalling a Preset Station:

Press the preset station button (#1-6) for the desired station.

The number of the recalled station is displayed.

Auto TP Seek Function

When the TI function is on and poor reception conditions are

experienced when listening to a traffic information station,

another traffic information station with better reception will be

searched for automatically. This function is on, when unit is

first powered on.

AF (Alternative Frequency) Function

When poor reception is experienced, automatically switch to

another frequency broadcasting the same programme in the

same RDS network with better reception.

The RDS indicator lights up when the AF function is turned on.

Display and setting:

"ATPS ON" : The Auto TP Seek Function is on.

If the traffic information station you are tuned to

experiences poor reception, this function

automatically seeks another TP station.

"ATPS OFF" : The Auto TP Seek Function is off.

Display and setting:

"AF ON" : The AF function is on.

"AF OFF" : The AF function is off.

NOTE

• When no other stations with stronger reception are available for

the same programme in the RDS network, you may hear the

incoming broadcast in bits and snatches. Turn off the AF

function in such a case.

• The AF function can be turned on or off even when the standby

mode has been turned on. If the power is on, the AF function

tunes in to stations that offer good reception.

Monaural Reception

When poor stereo reception is experienced, this function will

reduce noise and improve listening conditions.

Display and setting:

"MONO ON" : The monaural reception is on.

"MONO OFF" : The monaural reception is off.

Restricting RDS Region (Region Restrict Function)

You can choose whether or not to restrict the RDS channels,

received with the AF function for a particular network, to a

specific region. When the Region Restrict Function is on, the

region is restricted.

Display and setting:

"Regional ON" : The Region Restrict Function is on.

"Regional OFF" : The Region Restrict Function is off.

— 37 —

Menu settings

Basic Operations of steering remote control

Text Scroll

This function permits the CD text, MD title, Radio text, and

Calender function to be scrolled and the entire text to be

displayed. Switching Switching between manual scrolling and

automatic scrolling is permitted. The factory default is manual

scrolling.

Egnlish

ATT

∞

FM/DISC +

Display and setting:

"Scroll Auto" : Automatic scrolling

"Scroll Manual" : Manual scrolling

VOLUME

∞

FM/DISC+

AM/DISC–

SRC

NOTE

ATT

SRC

• Radio Text Scroll (page 21)

• Text / Title Scroll (page 27)

DWN

AM/DISC –

— 38 —

cannot be used.

2WARNING

• The external disc control mode will differ depending on the unit

that is connected.

• The AUX mode is available only when the changer / AUX

switching adapter (KCA-S210A or CA-C1AX) or CD changer

(KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is

connected to this unit.

During the AUX mode, "AUX" / AUX-name will show in the

display.

When the CA-C1AX is being used, the AUX Mode will replace

the External Disc Control Mode.

To prevent accidents, do not attempt to use the steering remote

control whilst turning the steering wheel.

Loading and Replacing the Lithium Battery:

Use one lithium battery (CR2025).

Insert the battery with the + and – poles aligned properly,

following the illustration.

• VOLUME buttons

Press the 5 button to turn the volume up.

Press the ∞ button to turn the volume down.

• ATT button

2WARNING

Turns down the volume quickly. To return the volume to its

original level, press the button again. Turning the volume up, or

turning it all the way down deactivates the attenuator function.

Store unused lithium batteries out of the reach of children.

Contact a doctor immediately if the battery is accidentally

swallowed.

Basic operations

Tuner features

• SRC button

• TUNE buttons

Each time you press the SRC button, the mode switches as

follows:

Press the 4 button to make decreasing seeks (using the

preset tuning mode).

Press the ¢ button to make increasing seeks (using the preset

tuning mode).

▼

Tuner mode

▼

• FM button

MD mode

Selects and switches between the FM1, FM2 and FM3 bands.

▼

• AM button

Selects the MW and LW bands.

External disc control mode 1

▼

External disc control mode 2/AUX mode

▼

Standby mode

NOTE

• The mode switches to the next mode from any mode which

— 39 —

Basic Operations of steering remote control

MD/External disc control features

• DISC buttons (for disc changers)

Press the AM/DISC– button to search through the discs

backwards.

Egnlish

Press the FM/DISC+ button to search through the discs

forwards.

• TRACK buttons

Press the 4 button to search through the tracks backwards.

Press the ¢ button to search through the tracks forwards.

— 40 —

5. Take Connector A on the wiring harness and connect it to the

external power connector on your vehicle.

6. Connect the wiring harness connector to the unit.

7. Install the unit in your car.

Accessories

External view

......... Number of items

8. Reconnect the - terminal of the battery.

.........1

2CAUTION

• If your car is not prepared for this special connection-system,

consult your KENWOOD dealer.

.........1

• Only use antenna conversion adapters (ISO-JASO) when the

antenna cord has an ISO plug.

• Make sure that all cable connections are securely made by

inserting jacks until they lock completely.

• If your vehicle's ignition does not have an ACC position, or if

the ignition cable is connected to a power source with constant

voltage such as a battery cable, the power will not be linked

with the ignition (i.e., it will not turn on and off along with the

ignition). If you want to link the unit's power with the ignition,

connect the ignition cable to a power source that can be turned

on and off with the ignition key.

• If the fuse blows, first make sure that the cables have not

caused a short circuit, then replace the old fuse with one with

the same rating.

• Do not let unconnected cables or terminals touch metal on the

car or anything else conducting electricity. To prevent short

circuits, also do not remove the caps on the ends of the

unconnected cables or the terminals.

2CAUTION

The use of any accessories except for those provided might

result in damage to the unit. Make sure only to use the

accessories shipped with the unit, as shown above.

• Connect the speaker cables correctly to the terminals to which

they correspond. The unit may receive damage or fail to work if

you share the - cables and/or ground them to any metal part

in the car.

• After the unit is installed, check whether the brake lamps,

indicators, wipers, etc. on the car are working properly.

• Insulate unconnected cables with vinyl tape or other similar

material.

• Some disc changers need conversion cables for connection.

See the section on "Safety Precautions" for details.

• If the console has a lid, make sure to install the unit so that the

faceplate does not hit the lid when closing and opening.

• Mount the unit so that the mounting angle is 30° or less.

Installation Procedure

1. To prevent short circuits, remove the key from the ignition and

disconnect the -terminal of the battery.

2. Make the proper input and output cable connections for each

unit.

3. Connect the cable on the wiring harness.

4. Take Connector B on the wiring harness and connect it to the

speaker connector in your vehicle.

— 41 —

Connecting Cables to Terminals

Antenna Conversion Adaptor (ISO–JASO) (Accessory3)

Antenna Cord (ISO)

Non-fading right output (Red)

Connector Function Guide

FM/AM

antenna input

Non-fading left output (White)

Rear right output (Red)

Pin Numbers for

Cable Colour

Functions

ISO Connectors

Egnlish

External Power

Rear left output (White)

Front right output (Red)

Connector

A–4

A–5

A–6

A–7

A–8

Yellow

Blue/White

Orange/White Dimmer

Red

Battery

Power Control

Front left output (White)

KENWOOD disc changer/DAB control input/

Display Data Output Jack

Outputs data representing the unit's current state,

causing it to appear in the external display.

To connect to this jack, a converting adapter

(optional) is necessary.

Ignition (ACC)

Earth (Ground)

Connection

Black

Speaker

Connector

Fuse(10A)

B–1

B–2

B–3

B–4

B–5

B–6

B–7

B–8

Purple

Purple/Black

Gray

Gray/Black

White

White/Black

Green

Rear Right (+)

Rear Right (–)

Front Right (+)

Front Right (–)

Front Left (+)

Front Left (–)

Rear Left (+)

Rear Left (–)

NOTE

Wiring harness

(Accessory1)

To connect the Disc changer or DAB unit,

consult each manual.

DC/DC converter box (Wrap the cushion

(Accessory0) around this box.)

2CAUTION

Separate this box from the unit and antenna cords. If they

are too close, it may cause the reception to get noise.

External amplifier

control cable

(Pink / Black)

Green/Black

To "EXT.AMP.CONT." terminal of the

EXT.CONT.

amplifier having the external amp

control function.

Battery cable (Yellow)

TEL mute cable (Brown)

Ignition cable (Red)

Connect to the terminal that is

grounded when either the telephone

rings or during conversation.

TEL MUTE

NOTE

To connect the KENWOOD navigation

system, consult your navigation manual.

Power control/ Motor antenna

A–7 Pin (Red)

control cable (Blue/White)

Connect either to the power control

terminal when using the optional

power amplifier, or to the antenna

control terminal in the vehicle.

P.CONT.

A–4 Pin (Yellow)

Connector A

ANT.CONT.

NOTE

If no connections are

made, do not let the cable

come out from the tab.

NOTE

If no connections are made,

do not cut the tube off from

the edge of the cable.

Connector B

— 42 —

Connecting Cables to Terminals

Installtion

■

2WARNING

Installation

Connecting the ISO Connector (see p.42)

The pin arrangement for the ISO connectors depends on the

type of vehicle you drive. Make sure to make the proper

connections to prevent damage to the unit.

Firewall or metal support

The default connection for the wiring harness is described in 1

below. If the ISO connector pins are set as described in 2 or 3,

make the connection as illustrated.

Screw (M4X8)

(commercially

available)

1 (Default setting) The A-7 pin (red) of the vehicle's ISO

connector is linked with the ignition, and the A-4 pin (yellow)

is connected to the constant power supply.

Unit

Vehicle

Ignition cable (Red)

A–7 Pin (Red)

Bend the tabs of the

mounting sleeve

with a screwdriver or

similar utensil and

attach it in place.

Battery cable (Yellow)

A–4 Pin (Yellow)

Self-tapping

screw

(commercially

available)

Metal mounting

strap

(commercially

available)

2 The A-7 pin (red) of the vehicle's ISO connector is connected

to the constant power supply, and the A-4 pin (yellow) is

linked to the ignition.

NOTE

Unit

Vehicle

Make sure that the unit is installed securely in place. If the unit

is unstable, it may malfunction (eg, the sound may skip).

Ignition cable (Red)

A–7 Pin (Red)

Battery cable (Yellow)

A–4 Pin (Yellow)

3 The A-7 pin (red) of the vehicle's ISO connector is not

connected to anything, whilst the A-4 pin (yellow) is connected

to the constant power supply (or both the A-7 (red) and A-4

(yellow) pins are connected to the constant power supply).

Unit

Vehicle

Connect to a power source that can be

turned on and off with the ignition key.

Ignition cable (Red)

2CAUTION

To attach this unit, make sure the front of the control panel faces

you and fit it into the mounting sleeve by pressing the four corners

of the hard rubber frame at the same time.

Battery cable (Yellow)

A–4 Pin (Yellow)

Do not apply strong pressure to other sections than the corners;

otherwise troubles such as the impossibility of opening or closing

the panel may result.

— 43 —

Removing the Unit

■

Removing the Unit

■

Removing the hard rubber frame

Insert the removal tool into the indentations in the hard rubber

frame, and pull it gently until the lock is released.

Make the faceplate control panel appear.

NOTE

When the control panel of the faceplate is hidden, the unit will

be locked by the sleeve, making it more difficult to remove

the unit.

Egnlish

Refer to the section “Removing the hard rubber frame” and

then remove the hard rubber frame.

Remove the screw (M4×8) on the back panel.

Insert the removal tool deeply, as illustrated, with the L on the

left and the R on the right.

Screw (M4X8)

(commercially

available)

Accessory4

Removal tool

Accessory2

Removal tool

Push upward the both

tools, as shown, and pull

the unit toward you until it

is halfway out. The unit

may drop if you pull it out

completely.

Pull the unit all the way out

with your hands, being

careful not to drop it.

— 44 —

Locking the faceplate to the unit

Attaching Steering Remote Control

Mounting Example

■

Locking the faceplate to the unit

If you want to lock the faceplate to the unit so that it does not

fall off, follow the directions below.

Refer to the function "Removing the faceplate (page 14)" and

remove the faceplate.

Insert the provided screw into the hole at the centre of the

bottom side of the faceplate which you have removed from

the unit.

Accessory5

Refer to the section "Removing the faceplate (page 14)" and

then reattaching the faceplate.

2CAUTION

Never insert the taptite screws (ø2 × 6 mm) in any other screw

holes than the one specified. If you insert it in another hole, it

will contract and may cause damage to the mechanical parts

inside the unit.

Attach the operation section and the light emitting section of the

Steering Remote Control as shown above.

Be sure to attach them to positions that can ensure proper

operation.

2CAUTION

• Clean dirt and oil from the positions where the Steering

Remote Control sections are to be attached.

• If the attached position is cold, warm it before attaching.

• The position should be selected so that the product does not

come in the way of steering operation.

• Do not attach anything on the surface of a steering wheel

incorporating an air bag.

• Before finally affixing the transmitter, check various angles to

find an orientation that provides faithful operation.

— 45 —

Troubleshooting Guide

What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring.

Before calling service, first check the following table for possible problems.

PROBLEM

POSSIBLE CAUSE

SOLUTION

The power does not turn on.

The fuse has blown.

After checking for short circuits in the cables, replace

the fuse with one having the same rating.

Egnlish

No ACC position on vehicle ignition.

The Attenuator function is turned on.

Connect the same cable to the ignition as the battery cable.

Turn off the Attenuator function.

No sound can be heard, or the

volume is low.

The fader and/or balance settings are set all the way to

one side.

Reset the fader and/or balance settings.

The input/output cables or wiring harness are connected

incorrectly.

Reconnect the input/output cables and/or the wiring

harness correctly. See the section on "Connecting

Cables to Terminals".

The values of “VOL OFFSET” are low.

Increase the values of “VOL OFFSET”. (see p. 10)

Press the reset button on the unit (see page 4).

Nothing happens when the

buttons are pressed.

The computer chip in the unit is not functioning normally.

A speaker cable may be pinched by a screw in the car.

The speakers are not wired correctly.

Check the speaker wiring.

The sound quality is poor or

distorted.

Reconnect the speaker cables so that each output

terminal is connected to a different speaker.

Radio reception is poor.

The car antenna is not extended.

Pull out the antenna all the way.

The antenna control cable is not connected.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

The memory is erased when

the ignition is turned off.

The battery cable has not been connected to the proper

terminal.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

The ignition and battery cable are incorrectly connected.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

The TEL mute function does

not work.

The TEL mute cable is not connected properly.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

The TEL mute function turns

on even though the TEL mute

cable is not connected.

The TEL mute cable is touching a metal part of the car.

The faceplate is incorrectly attached.

Pull the TEL mute cable away from the metal part of the

car.

The faceplate does not open or

close.

Reattach the faceplate correctly, See the section on

"Removing the Faceplate".(page.14)

— 46 —

Troubleshooting Guide

MD/External disc control mode

PROBLEM

POSSIBLE CAUSE

SOLUTION

MD mode cannot be set.

The faceplate was closed whilst the MD was being

ejected.

Press the eject(0) button and reinsert the MD.

The MD cannot be inserted.

The MD does not load.

There is already an MD loaded.

Eject the currently loaded MD and then load the new one.

Insert the MD in the proper orientation.

The insertion orientation of the MD is incorrect or the MD

is upside down.

The MD loads but soon comes

out again.

Nothing is recorded on the MD.

Replace the MD with one that is recorded.

The sound skips.

The mounting angle exceeds 30°.

The mounting is unstable.

Adjust to an angle of less than 30°.

Fix the unit securely. When the sound skips at the same

portion even when the car is stopped, the problem lies

with the MD.

There is noise during playback.

The MD is soiled with dust or dirt.

If another MD is played back and there is no problem, then

the problem is due to the sound quality of the MD itself.

Turn off the random play or magazine random play

function.

The specified track does not

play.

Random play or magazine random play has been

selected.

Track repeat, disc repeat, track

scan, disc scan, random play,

and magazine random play

start by themselves.

The setting is not cancelled.

The settings for these functions remain on until the

setting to off or the disc ejected, even if the power is

turned off or the source changed.

The disc control mode cannot

be selected.

No cable has been connected to the disc changer input

terminal on the unit.

Connect the cable to the disc changer input terminal on

the unit.

The specified disc does not

play, but another one plays

instead.

The specified CD is very dirty.

The CD is upside-down.

Clean the CD.

Load the CD with the labelled side up.

The disc is loaded in a different slot from that specified.

Eject the disc magazine and check the number for the

specified disc.

The disc is severely scratched.

Something is touching the disc changer.

The CD is scratched or dirty.

Try another disc instead.

The sound skips.

Remove whatever is touching it.

If skipping happens at the same place when the car is

stopped, something is wrong with the CD. Clean the CD.

The display shows that the

changer is being played, but no

sound can be heard.

The computer chip in the unit is not functioning normally.

Press the reset button on the unit (see page 4).

— 47 —

Troubleshooting Guide

The following messages are displayed when certain problems are occurring in your system. Take the

recommended actions.

No disc magazine has been loaded in the changer. The disc magazine is not completely loaded.

EJECT

] Load the disc magazine properly.

No CD in the unit.

] Insert the CD.

Egnlish

No disc has been loaded in the disc magazine.

NO DISC

E-04

] Load a disc into the disc magazine.

No disc has been loaded in the disc magazine.

] Load a disc into the disc magazine.

The CD is very dirty. The CD is upside-down. The CD is scratched a lot.

] Clean the CD and load it correctly.

Nothing has been recorded on the MD.

BLANK

No tracks are recorded on the MD, although it has a title.

NO TRACK

NO PANEL

The faceplate of the slave unit being connected to this unit has been removed.

] Replace it.

The unit is malfunctioning for some reason.

E-77

E-99

] Press the reset button on the unit. If the "E- 77", code does not disappear, consult your nearest service centre.

Something is wrong with the disc magazine. Or the unit is malfunctioning for some reason.

] Check the disc magazine. And then, press the reset button on the unit.

If the "E- 99" code does not disappear, consult your nearest service center.

The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60°C (140°F),

HOLD

stopping all operation.

] Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60°C (140°F),

the disc starts playing again.

The MD player section is not operating properly.

•••

(MD-IN)

] Reinsert the MD. If the MD cannot be ejected or the display continues to flash even when the MD has been properly

reinserted, please switch off the power and consult your nearest service centre.

If the following situations, consult your nearest service centre:

• Even though the disc changer is connected, the Disc Changer Mode is not on, with "AUX" showing in the display during the Changer Mode.

• Even though no device (KCA-S210A, CA-C1AX, KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is connected, the AUX Mode is entered when switching modes.

— 48 —

Specifications

Specifications subject to change without notice.

FM tuner section

Audio section

Frequency range (50 kHz Space)..............87.5 MHz – 108.0 MHz

Usable sensitivity (S/N=26dB) ..................................0.7 µV/75 Ω

Quieting Sensitivity (S/N=46dB).................................1.6 µV/75 Ω

Frequency response ( 3.0 dB)..............................30 Hz – 15 kHz

Signal to Noise ratio (MONO)..............................................65 dB

Selectivity (DIN) (400kHz).................................................≥ 80 dB

Stereo separation (1 kHz) ....................................................35 dB

Maximum output power.................................................45 W × 4

Output power (DIN 45324, +B=14.4V)...........................28 W × 4

Tone action

Bass: ...........................................................100 Hz 10 dB

Treble: .........................................................10 kHz 10 dB

Preout level / Load ................................4500 mV/10 kΩ (MD/CD)

Preout impedance.................................................................80 Ω

MW tuner section

General

Frequency range (9kHz Space)......................531 kHz – 1611 kHz

Usable sensitivity (S/N=20dB) .............................................25 µV

Operating voltage .............................14.4 V (11 – 16 V allowable)

Current consumption.............................................................10 A

Installation size (W × H × D) ..........................182 × 53 × 162 mm

Weight...............................................................................1800 g

LW tuner section

Frequency range .............................................153 kHz – 281 kHz

Usable sensitivity (S/N=20dB) .............................................45 µV

MD player section

Laser diode....................................................GaAlAs (λ=780 nm)

Digital filter (D/A) .....................................8 Times Over Sampling

D/A Converter .......................................................................1 Bit

Spindle speed ..............................................400 – 900 rpm (CLV)

Wow & Flutter........................................Below Measurable Limit

Frequency response ( 2 dB).................................20 Hz – 20 kHz

Total harmonic distortion (1 kHz) ......................................0.01 %

Signal to Noise ratio ................................................90 dB (1 kHz)

Dynamic range ....................................................................90 dB

Channel separation..............................................................85 dB

— 49 —

Insignia CD Player NS A2113 User Manual
JBL Speaker System 1000 ARRAY User Manual
JBL Stereo Amplifier DA1002 User Manual
JBM electronic Switch C 130 User Manual
JVC DVD Recorder DR M70SEK User Manual
Kathrein Satellite TV System UFD 170 User Manual
King Kutter Lawn Mower Rotary Mower User Manual
KitchenAid Dishwasher KUDU03FTSS0 User Manual
Kodak Scanner A 61195 User Manual
Konica Minolta All in One Printer 4690MF User Manual