ELECTRIC & GAS DRYER
Use & Care Guide
SECADORAA GAS Y ELÉCTRICA
Manual de Uso y Cuidado
Models/Modelos
Electric/Eléctica: 80412
Gas: 90412
P/N 134686200D (0807)
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
GAS DRYERS:
ELECTRIC DRYERS:
Do not under any
14-30R
circumstances cut,
remove, or bypass
Groundingtype
wall receptacle
DRYER
thegroundingprong
from this plug
FUSED30AMP
120/240 V OR
120/208 V
WALL
RECEPTACLE
DRYER
SERVICECORD
CORRECT
CORRECT
Use this way ONLY
Use this way ONLY
SAVE THESE INSTRUCTIONS
Important Safety Instructions
You can be killed or seriously injured if you don't follow these Important Safety Instructions:
Avoid fire hazard or electrical shock. Do not use an adaptor plug or extension cord or remove grounding prong
from electrical power cord. Failure to follow this warning can cause serious injury, fire or death.
•Toreducetheriskoffire, electricalshock, orinjurytopersonswhenusingthisdryer, complywiththebasicwarningslistedbelow.
• Failure to comply with these warnings could result in serious personal injuries.
PreventFire
• Do not dry items that have been previously cleaned in, soaked in, or spotted with gasoline, cleaning solvents, kerosene, waxes,
etc. Do not store these items on or near the dryer. These substances give off vapors that could ignite or explode.
• Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical
reaction that could cause a load to catch fire.
• Do not dry articles containing rubber, plastic or similar materials such as bras, galoshes, bath mats, rugs, bibs, baby pants,
plastic bags and pillows that may melt or burn. Some rubber materials, when heated, can under certain circumstances produce
firebyspontaneouscombustion.
• Clean the lint screen before or after each load. The interior of the dryer, lint screen housing and exhaust duct should be cleaned
approximately every 18 months by qualified service personnel. An excessive amount of lint build-up in these areas could result in
inefficient drying and possible fire. See Care and Cleaning.
• Do not operate the dryer if the lint screen is blocked, damaged or missing. Fire hazard, overheating and damage to fabrics can
occur. If your dryer has a drying rack, always replace the lint screen when finished using the drying rack.
•-RiskofFire-Aclothesdryerproducescombustiblelint. Thedryermustbeconnectedtoanexhaustoutdoors. Regularlyinspect
the outdoor exhaust opening and remove any accumulation of lint around the outdoor exhaust opening and in the surrounding
area.
• Do not obstruct the flow of ventilating air. Do not stack or place laundry or throw rugs against the front or back of the dryer.
• Do not spray any type of aerosol into, on or near dryer at any time.
• Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or
product.
• Failure to comply with these warnings could result in fire, explosion, serious bodily injury and/or damage to the rubber or plastic
parts of the dryer.
ProtectChildren
• Do not allow children to play on or in the dryer. Close supervision of children is necessary when the dryer is used near children.
As children grow, teach them the proper, safe use of all appliances.
•Destroythecarton,plasticbagandotherpackingmaterialsafterthedryerisunpacked.Childrenmightusethemforplay.Cartons
covered with rugs, bedspreads or plastic sheets can become airtight chambers.
• Keep laundry products out of children's reach. To prevent personal injury, observe all warnings on product labels.
• Before the dryer is removed from service or discarded, remove the dryer door to prevent accidental entrapment.
• Failure to comply with these warnings could result in serious personal injuries.
PreventInjury
•Topreventshockhazardandassurestabilityduringoperation, thedryermustbeinstalledandelectricallygroundedbyaqualified
service person in accordance with local codes. Installation instructions are packed in the dryer for the installer's reference. Refer
to INSTALLATION INSTRUCTIONS for detailed grounding procedures. If the dryer is moved to a new location, have it checked and
reinstalled by a qualified service person.
•Topreventpersonalinjuryordamagetothedryer,theelectricalpowercordofagasdryermustbepluggedintoaproperlygrounded
and polarized 3-prong outlet. The third grounding prong must never be removed. Never ground the dryer to a gas pipe.
Do not use an extension cord or an adaptor plug.
Printed in U.S.A.
3
Important Safety Instructions (con't)
• ALWAYS disconnect the dryer from the electrical supply before attempting any service or cleaning. Failure to do so can result
in electrical shock or injury.
• Do not use any type spray cleanser when cleaning dryer interior. Hazardous fumes or electrical shock could occur.
• To prevent injury, do not reach into the dryer if the drum is moving. Wait until the dryer has stopped completely before reaching
into the drum.
• To prevent injury and damage to the dryer:
-
AllrepairsandservicingmustbeperformedbyanauthorizedservicerunlessspecificallyrecommendedinthisOwner's
Guide. Use only authorized factory parts.
-
-
Do not tamper with controls.
Do not install or store the dryer where it will be exposed to the weather.
• A thermal limiter switch automatically turns off the motor in the unlikely event of an overheated situation (electric dryers only).
A service technician must replace the thermal limiter switch after correcting the fault.
• Failure to comply with these warnings could result in serious personal injuries.
Pedestal
A pedestal accessory specifically designed for this dryer may be used when elevating the dryer for ease of use.
Failure to use accessories certified by the manufacturer could result in personal injury, property damage or damage to the dryer.
• Follow the guidelines below for preparing the load for drying.
• Read the Operating Instructions card for operating your specific model.
Drying Procedures
• Always read and follow fabric care labels and laundry product labels.
To reduce the risk of fire, electrical shock, or injury to persons, read
Important Safety Instructions before operating this dryer.
1. Prepare items for drying.
•
•
Dry items of similar fabric, weight and construction in the same load.
Separate dark items from light-colored items. Separate items that shed lint
from those that attract lint. If an item sheds lint, turn it inside out.
Besurebuckles,buttonsandtrimareheatproofandwon'tdamagethedrum
finish. Close zippers, fasten hooks and Velcro®-like fasteners. Tie strings
and sashes to prevent snagging and tangling.
•
Follow fabric care label instructions.
•
•
If possible, turn pockets inside out for even drying.
Check for stains which may not have been removed in washing. Dryer heat
may permanently set some stains. Repeat stain removal process before
drying.
•
Place small items in a mesh bag to prevent tangling and for easy removal.
2. Check that lint screen is clean and in place.
3. Load the dryer.
•
•
•
•
•
Theaverageloadwillfillthedrum1/3to1/2full.Itemsneedroomtotumble
freely for even drying and less wrinkling. Do not overload dryer.
Whendryinglargeitems,dryonly2or3atatime.Fillouttheloadwithsmall
and medium sized items.
For delicate or very small loads, add 2 lint-free towels for better drying, less
wrinkling, and to prevent grease stains caused by fabric softener sheets.
Donotoverdryitems.Overdryingcancausewrinkling,shrinkage,harshness,
and a build-up of static electricity, which can produce more lint.
If desired, add a dryer fabric softener sheet.
Place small items in a mesh bag.
4. Close the dryer door and set dryer controls (some models).
See Operating Instructions for your specific model controls.
5. Select cycle and settings according to type of load, level of dryness and/
or options desired.
6. Start the dryer.
•
•
Turn the START knob clockwise to ON. Hold for 1-2 seconds and release.
Toaddorremoveitemswhenthedryerisrunning,openthedoor.Thedryer
will always stop when the door is opened. Allow the drum to come to a
complete stop before reaching inside.
•
To restart dryer, close the door then turn the START knob clockwise to ON.
Hold for 1-2 seconds and release.
7. Whenthecycleends,removeitemsimmediatelyandhangorfold.Ifload
Fill dryer drum 1/3 to 1/2 full.
is removed before the cycle ends, turn cycle selector to OFF.
4
Cycle Signal Control (some models)
Features
When the Cycle Signal Control is ON, a signal will sound at the end of each
cycle and during the WRINKLE-RID setting (some models). The volume is
adjustable on some models.
Drum Light (some models)
A drum light will come on whenever the door is opened to illuminate the dryer
drum during loading and unloading. Closing the door turns off the light.
ReversibleDryerDoor
Your dryer is equipped with a reversible door. The door can be hinged on the
right or left side. Refer to the INSTALLATION INSTRUCTIONS for directions on
changing the door.
Drying Rack (some models)
Use the drying rack to dry items which should not be tumble dried.
1. Open the dryer door and remove the lint screen.
2. Insert drying rack into the dryer drum. Place the front bar under the lip of the
lint screen opening.
3. Place items to be dried on top of the rack. Weight should not exceed 10 lbs.
Leave space between items, but do not let items hang over the sides or
through the grids. Do not tumble other items when using the drying rack.
4. Select a timed dry setting best suited for items being dried. Use only the Air
Fluff (no heat) temperature setting for items containing plastic, foam rubber,
rubber-like materials, feathers or down.
5. When items are dry, remove the rack and replace the lint screen. If lint
screen is not in place, tumbling items could enter the exhaust system and
cause damage to the dryer.
Place the front bar under
the lip of the lint screen opening.
Common Drying Problems
Many drying problems involve poor cleaning results, poor soil and stain removal, residues of lint and scum, and fabric damage. For
satisfactory drying results, follow these suggestions provided by The Soap and Detergent Association.
PROBLEM
POSSIBLECAUSES
SOLUTIONS
PREVENTIVEMEASURES
Greasy, oily
stains
• Rub fabric softener stains with bar soap.
Rinse and rewash.
• Add a few bath towels to small loads for
proper tumbling.
• Some"silk-like"fabricsshouldbeairdried.
• Use proper drying temperature.
• Place fabric softener sheet on top of load
before starting the dryer.
• Fabric softener sheet.
Lint
• Reduce load size and rewash using liquid
fabric softener in the final rinse.
• Or, add a fabric softener sheet and tumble
without heat.
• Overloading.
• Overdrying causes static
electricity.
• Lint screen not clean when
cycle began.
• Lint is attached to "pills."
• Do not overload dryer.
• Use fabric softener in washer or dryer to
reduce static electricity.
• Removeitemswhentheyareslightlydamp
to avoid overdrying.
• Check that lint screen is clean and in place.
• Use lint brush or roller to remove lint.
Pilling
• Use a lint brush or shaver to remove pills.
• Irreversible condition.
• Use fabric softener to lubricate fibers.
• When ironing, use spray starch or fabric
finish on collars and cuffs.
• Pilling is normal with
synthetic and permanent
press fabrics. This is due to
abrasionfromnormalwear.
(Fibers break
off, ball up and
cling to fabric.)
• Turn items inside out to reduce abrasion.
Shrinking
• Overdrying.
• Follow fabric care label directions.
• If shrinking is a concern, check load often.
• Remove items while slightly damp and
hang or lay flat to complete drying.
• Block knits into shape.
Wrinkling
• Reduce load size and tumble at medium or
low heat for 5-10 minutes.
• Remove items immediately. Hang or fold.
• Overloading.
• Leaving items in dryer after
cycle ends.
• Do not overload dryer.
• Remove items as soon as cycle ends.
5
Care and Cleaning
Toreduceriskoffireorseriousinjurytopersonsorproperty,comply
with the basic warnings listed in Important Safety Instructions and those listed
below.
•
•
Before cleaning the dryer interior, unplug the electrical power cord to avoid
electrical shock hazards.
Do not use any type spray cleanser when cleaning dryer interior. Hazardous
fumes or electrical shock could occur.
Inside
• Cleanthelintscreenaftereveryload.Lintbuild-upinthescreenrestrictsairflow,
whichcauseslongerdryingtimes.Thescreenislocatedatthebottomofthedoor
opening.Removebypullingstraightup.Removethelintandreplacethescreen.
CAUTION - Risk of Fire - A clothes dryer produces combustible lint. The dryer
must be connected to an exhaust outdoors. Regularly inspect the outdoor
exhaust opening and remove any accumulation of lint around the outdoor
exhaust opening and in the surrounding area.
•
Occasionallyawaxybuild-upmayformonthelintscreenfromusingdryer-added
fabric softener sheets. To remove this build-up, wash the lint screen in warm,
soapy water. Dry thoroughly and replace. Do not operate the dryer without the
lint screen in place.
•
•
Ifthedryerdrumbecomesstainedfromnoncolorfastfabrics,cleanthedrumwith
a damp cloth and a mild liquid household cleanser. Remove cleanser residue
before drying the next load.
Cleanlintscreenaftereveryload.
Every 18 months a Sears or other qualified service dealer should clean the dryer
cabinetinteriorandexhaustduct.Theseareascancollectlintanddustovertime.
Anexcessiveamountoflintbuild-upcouldresultininefficientdryingandpossible
fire hazard.
Outside
•
•
•
•
•
Clean the cabinet with mild soap and water. Never use harsh, gritty or
abrasivecleansers.
If the cabinet becomes stained, clean with diluted chlorine bleach [1/2 cup
(120 ml) in 1 quart (.95 liter) water]. Rinse several times with clear water.
Removeglueresiduefromtapeorlabelswithamixtureofwarmwaterandmild
detergent. Or, touch residue with the sticky side of the tape or label.
Do not store or place laundry products
on top of dryer at any time. They can
damage the finish or controls.
When cleaning chrome parts use Windex with ammonia or any of the cleaning
items mentioned for cleaning the cabinet.
Before moving the dryer, place a strip of cardboard or thin fiberboard under
the front leveling legs to prevent damage to floor.
6
Before calling for service, review this list. It may save both time and expense. The list includes
common occurrences that are not the result of defective workmanship or materials in this dryer.
Avoid Service
Checklist
OCCURRENCE
Dryer does not start.
POSSIBLE CAUSE
Electrical power cord is not securely
plugged in or plug may be loose.
SOLUTION
Make sure the plug fits tightly in wall outlet.
Reset circuit breaker or replace fuse.
House fuse blown or circuit breaker
tripped.
Make sure electrical line is not overloaded and the dryer is
on a separate circuit.
Call Sears or other qualified service dealer
Replace fuse.
Thermal limiter tripped.
There are 2 house fuses in the dryer circuit.
If 1 of the 2 fuses is blown, the drum may
turn but the heater will not operate.
Dryer runs but won't heat.
Check to make sure supply valve is open. See
INSTALLATION INSTRUCTIONS for procedure.
Gas supply valve is not open (gas models).
See INSTALLATION INSTRUCTIONS.
Dryer does not have anough air supply to
support the burner flame (gas models).
Refill or replace tank.
LP gas supply tank is empty or there has
been a utility interruption of natural gas
(gas models).
Dryer should heat when utility service is restored.
Make sure all lint has been removed from the dryer lint
screen before starting each cycle.
Lint screen is clogged with lint.
Drying cycle takes too long,
outsideofthedryerfeelstoo
hot or smells hot.
Exhaust duct must be at least 4 inches in diameter and
made of rigid or flexible metal.
Exhaust duct requirements have not been
met.
When in place, the duct must have no more than two 90°
bends and must not exceed length listed in
INSTALLATION INSTRUCTIONS.
Drying time will be 20% longer than drying on a 240 volt
circuit.
Electric dryer is connected to a 208 volt
circuit.
See Drying Procedures.
Drying procedures have not been
followed.
Clean out any obstruction.
Outside exhaust hood or exhaust duct may
be clogged or restricted.
Use a dehumidifier near the dryer.
Do not overload. See Drying Procedures.
Remove items as soon as cycle ends.
See Drying Procedures.
High humidity.
Dryer is overloaded.
Excessive wrinkling.
Items left in dryer too long.
Insufficient sorting of items.
Drying temperature too high.
Follow fabric care label instructions.
Always remove foreign objects from pockets before
laundering. Remove objects from drum and restart dryer.
Foreign objects such as coins, pins, clips or
buttons are inside the dryer.
Scratchingorchippingofthe
drumfinish.
It may be necessary to baste a scrap of material securely
around ornaments before drying to prevent scratching
and damage to the dryer.
Permanently attached items such as belt
buckles, zippers and fasteners may be
hitting the inside of the drum.
Drum damage caused by foreign objects or
permanently attached items is not covered by the
warranty.
7
Kenmore Appliance Warranty
One Year Limited Warranty
When installed, operated and maintained according to all instructions supplied with the product, if this appliance fails due to
a defect in material or workmanship within one year from the date of purchase, call 1-800-4-MY-HOME®
(1-800-469-4663)toarrangeforfreerepair.
Ifthisapplianceisusedforotherthanprivatefamilypurposes, thiswarrantyappliesforonly90daysfromthedateofpurchase.
This warranty covers only defects in material and workmanship. Sears will NOT pay for:
1. Expendable items that can wear out from normal use, including but not limited to filters, belts, light bulbs, and bags.
2. A service technician to instruct the user in correct product installation, operation or maintenance.
3. A service technician to clean or maintain this product.
4. Damage to or failure of this product if it is not installed, operated or maintained according to all instructions supplied with the
product.
5. Damage to or failure of this product resulting from accident, abuse, misuse or use for other than its intended purpose.
6. Damage to or failure of this product caused by the use of detergents, cleaners, chemicals or utensils other than those
recommended in all instructions supplied with the product.
7. Damage to or failure of parts or systems resulting from unauthorized modifications made to this product.
Disclaimer of implied warranties; limitation of remedies
Customer’ssoleandexclusiveremedyunderthislimitedwarrantyshallbeproductrepairasprovidedherein.Impliedwarranties,
includingwarrantiesofmerchantabilityorfitnessforaparticularpurpose, arelimitedtooneyearortheshortestperiodallowed
bylaw.Searsshallnotbeliableforincidentalorconsequentialdamages.Somestatesandprovincesdonotallowtheexclusion
or limitation of incidental or consequential damages, or limitations on the duration of implied warranties of merchantability or
fitness, so these exclusions or limitations may not apply to you.
This warranty applies only while this appliance is used in the United States and Canada.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8
Master Protection Agreement
IntheU.S.A
Congratulations on making a smart purchase. Your new Kenmore® appliance is designed and manufactured for years of dependable
operation. But like all products, it may require preventive maintenance or repair from time to time. That’s when having a Master Protection
Agreement can save you money and aggravation.
The Master Protection Agreement also helps extend the life of your new appliance. Here’s what’s included in the Agreement:
√
√
Parts and labor needed to help keep products operating prop-erly under normal use, not just defects. Our coverage
goes well beyond the product warranty. No deductibles, no functional failure excluded from
coverage— real protection.
Expert service by a force of more than 10,000 authorized Sears service technicians, which means someone you can
trust willbe working on your product.
√
√
Unlimited service calls and nationwide service, as often as you want us, whenever you want us.
“No-lemon” guarantee – replacement of your covered product if four or more product failures occur within twelve
months.
√
√
√
Product replacement if your covered product can’t be fixed.
Annual Preventive Maintenance Check at your request – no extra charge.
Fast help by phone – we call it Rapid Resolution – phone sup-port from a Sears representative on all products. Think of
us as a “talking owner’s manual.”
√
√
Power surge protection against electrical damage due to power fluctuations.
$250 Food Loss Protection annually for any food spoilage that is the result of mechanical failure of any covered
refrigerator or freezer.
√
√
Rental reimbursement if repair of your covered product takes longer than promised.
10% discount off the regular price of any non-covered repair service and related installed parts.
Once you purchase the Agreement, a simple phone call is all that it takes for you to schedule service. You can call anytime day or night,
or schedule a service appointment online.
The Master Protection Agreement is a risk free purchase. If you cancel for any reason during the product warranty period, we will provide
a full refund. Or, a prorated refund anytime after the product warranty period expires. Purchase your Master Protection Agreement today!
Sears Installation Service
Some limitations and exclusions apply.
For prices and additional information,
call 1-800-827-6655.
For Sears guaranteed professional installation of home
appliances and items like garage door openers and
water heaters, in the U.S.A. call 1-800-4-MY-HOME®
8
|