MODEL • MODÈLE • MODELO
#840068
RECIPROCATING SAW
INSTRUCTION MANUAL
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,
MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND
UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE
TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE
PRODUCT, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER
SERVICE DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL, HAVE THE FOLLOWING
INFORMATION AVAILABLE: MODEL NO., DATE PURCHASED AND STORE LOCATION. AN
ALLTRADE REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU
WOULD LIKE TO MAKE A SUGGESTION OR COMMENT, GIVE US A CALL OR EMAIL US AT:
INFO@ALLTRADETOOLS.COM. YOUR FEEDBACK IS VITAL TO US.
FOR CUSTOMER SERVICE
POUR LE SERVICE APRÉS VENTE
OU DU CONSOMMATEUR
87-1904-60957
KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™ MOTORS CORP.,
U.S.A., WHICH DOES NOT MANUFACTURE OR DISTRIBUTE THIS PRODUCT.
CONSUMER INQUIRES SHOULD BE DIRECTED TO:
PARA EL SERVICIO
PARA EL CONSUMIDOR
©COPYRIGHT 2005 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA
840068_Corded Reciprocating Saw
1-800-590-3723
POWER TOOL SAFETY AND USE
PERSONAL SAFETY
!CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
Stay alert. Watch what you are doing, and use common
sense when operating a power tool. Do not use a power tool while tired or
under the influence of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal injury.
NOTE provides additional information that is useful
for proper use and maintenance of this tool. If a
NOTE is indicated make sure it is fully understood.
Before use, check for damaged or defective parts. Do not use the tool if any part
is damaged or defective. Carefully check the tool for damage. Check for breakage
of parts, damage to guards, switches, misalignment and seizure of moving parts, or
any other conditions that may affect the tool’s operation. Ensure that the tool will
operate properly and perform its intended function. Have any damaged or defective
parts repaired or replaced by an authorized repair agent. Never attempt to do any
repairs yourself. Do not use the tool if the switch does not turn it “ ON” or “ OFF” .
IMPORTANT SAFEGUARDS
People with electronic devices, such as pacemakers, should consult their
physician(s) before using this product. Operation of electrical equipment in
close proximity to a heart pacemaker could cause interference or failure of
the pacemaker.
Use safety equipment. Always wear eye protection. Dust mask, non-skid safety
shoes, hard hat or hearing protection must be used for appropriate conditions.
Dress properly. Do not wear loose clothing or jewelry. Keep long hair, clothing and
gloves away from moving parts. Loose clothes, jewelry or long hair can be caught
in moving parts.
Some dust created by grinding, drilling, sawing, sanding, and other
construction activities contains chemicals known to the State of California to
cause cancer, birth defects or other reproductive harm. Some examples of
these chemicals are:
Remove adjusting keys or wrenches before turning the power tool “ ON” .
A wrench or a key that is left attached to a rotating part of the power tool may result
in personal injury.
• Lead from lead-based paints,
Do not overreach. Keep proper footing and balance at all times. Proper footing
and balance enables better control of the power tool in unexpected situations.
• Crystalline silica from bricks and cement and other masonry products, and
arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.
Handling the power cord on this product may expose you to lead, a chemical
known to the State of California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
3
4
SAFETY RULES FOR RECIPROCATING SAW
ELECTRICAL SAFETY
Always wear safety goggles or eye protection when using this tool. Use a dust
mask or respirator for applications which generate dust.
Do not abuse the power cord or use a damaged power cord.
Secure the material being worked on. Never hold it in your hand or across your
legs. Unstable support can cause loss of control and injury.
Never use the power cord to carry the tools or pull the plug from an outlet.
Keep the power cord away from heat, oil, sharp edges or moving parts.
Replace damaged power cords immediately. Damaged power cords increase
the risk of electric shock.
When using the Reciprocating Saw, always maintain a firm grip on the tool with
both hands. Never put your hands or feet in the cutting area. Do not grasp the tool
or place your hands too close to the blade. Keep your hands well away from the
blade. Never reach underneath the tool while the blade is in motion. Do not use your
legs or feet to stabilize the work piece.
WORK AREA
Position yourself to avoid being caught between the tool or side handle and walls
or posts. Should the blade become bound or jammed in the work, it could result in
loss of control and injury.
Make sure that the work area is appropriate and safe to prevent accidents.
Always hold the tool by its insulated gripping surfaces when cutting in areas that
may contain hidden live wiring. If the blade makes contact with a live wire, the
metal parts of this tool may conduct enough electricity to seriously shock the user.
Contact with a “live” wire will make exposed metal parts of the tool “live” and shock
the operator. Do not cut or break into existing walls or other blind areas where
electrical wiring may exist. If this situation is unavoidable, disconnect all fuses or
circuit breakers feeding this worksite.
Keep your work area clean and well lit. Cluttered work benches and dark work
areas may cause accidents or injury.
Do not operate power tools in explosive areas, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the
dust or fumes.
Keep bystanders, children and visitors away while operating a power tool.
Distractions can cause you to lose control. Protect others in the work area from
debris such as chips and sparks. Provide barriers or shields as needed.
Check to see that keys and adjusting wrenches are removed from the saw before
switching the tool “ ON” . Keys or wrenches can fly away at high velocity striking
you or a bystander.
Do not run the Reciprocating Saw while carrying it at your side. A moving blade
Do not use this tool in a damp or wet environment.
could cause serious personal injury.
Do not use the Reciprocating Saw if it has been damaged, left outdoors in the
rain, snow, wet or damp environments, or immersed in liquid.
TOOL USE AND CARE
Do not use dull or damaged blades.
Do not use the power tool if the power switch does not
turn it “ ON” or “ OFF” . Any tool that cannot be controlled with the power switch
is dangerous and must be replaced.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control.
When restarting a saw in the workpiece, check that teeth are not engaged in
the material.
Store idle tools out of reach of children and other untrained persons. Tools are
dangerous in the hands of untrained users.
Keep the handle of the Reciprocating Saw dry, clean, and free from oil and
grease.
Disconnect the power cord plug from the power source before making any
adjustments, changing accessories or storing the tool. Such preventive safety
measures reduce the risk of starting the tool accidentally.
Be extra careful when cutting in high or hard-to-reach locations. Be on the
lookout for hidden wires and falling debris.
Maintain labels and nameplates on the Reciprocating Saw. These carry important
information. If unreadable or missing, contact Alltrade for a replacement.
5
6
Use clamps (not included) or other practical ways to secure and support the
work piece to a stable platform. Holding the work by hand or against your body is
unstable and may lead to loss of control.
OPERATING INSTRUCTIONS
3
2
Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained
tools with a sharp cutting edge are less likely to bind and are easier to control. Do
not use a damaged tool. Tag damaged tools “Do not use” until repaired.
4
5
Do not force the tool. Use the correct tool for your application. The correct tool
will do the job better and safer at the rate for which it is designed.
6
1
SYMBOLS
IMPORTANT: Some of the following symbols may be used on your tool. Please
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.
SYMBOL
NAME
Volts
Amperes
Hertz
Watt
Kilograms
Alternating Current
Direct Current
EXPLANATION
Voltage (Potential)
Current
Frequency (Cycles per Second)
Power
Weight
Type of Current
Type of Current
V
A
Hz
W
Kg
CONTROLS AND COMPONENTS:
ACCESSORIES:
1. Trigger Switch
5. Saw Blades (2)
2. Lock-On Button
3. Blade Clamp
4. Shoe
6. Wrench
Alternating or Direct Current Type of Current
Earthing Terminal
Class II Construction
Minutes
Grounding Terminal
Denotes Double Insulation
Time
Time
min
s
Seconds
Diameter
Size of Drill Bits,
Grinding Wheels, etc.
No load speed
No-load Rotational Speed
.../min
Revolutions per Minute
Revolutions, Surface Speed,
Strokes, etc. per Minute
1,2,3, …
Ring Selector Settings
Speed, Torque or Position Settings
7
8
VARIABLE SPEED TRIGGER SWITCH AND LOCK-ON BUTTON
GENERAL CUTTING
Never tape the trigger switch down to provide continuous
high speed. The tool may fail under such conditions causing fire or personal
injury.
Always hold the saw in front of you and away from your body. Keep your
hands and feet well away from the work piece.
Never feed the blade into the work piece until the blade is at full speed. If
the blade is not at full speed, the saw may kick back causing serious
personal injury.
LOCK-ON BUTTON
Do not force the saw. Excessive force may result in a
broken blade. Use only enough pressure to keep the saw moving through the
work piece.
TRIGGER
THIS TOOL IS CONTROLLED
BY A TRIGGER SWITCH:
• Put on eye
protection.
• The speed of the Reciprocating
Saw depends on the amount of
pressure applied on the trigger.
The further the trigger is pressed,
the faster the tool will go.
• Clear the saw of any
foreign material.
• Make sure the work piece is held
securely in place. Hold smaller pieces
in a vise or attach to the workbench
with clamps.
• To maintain a certain speed, pull the “On/Off” trigger to turn the Reciprocating Saw
“ ON” and engage the lock-on button. To turn the Reciprocating Saw “ OFF” ,
release the trigger switch. The lock-on button will automatically reset.
• Mark out the line to be cut so it is easily visible.
• Pull the trigger to start the saw.
ATTACHING / REMOVING BLADE
• Set the shoe against the work piece.
BLADE CLAMP
TO ATTACH BLADE:
• Turn the blade
clamp to the
• When the blade reaches full speed, slowly feed the blade into the work piece.
right with fingers.
PLUNGE CUTTING
• Insert blade, then release
the blade clamp to make
sure it is securely fastened.
Never feed the blade into the work piece until the blade
is at full speed. If the blade is not at full speed, the saw may kick back
causing serious personal injury.
• Make sure that the teeth are
facing downward.
Do not force the saw. Excessive force may result in a
broken blade. Use only enough pressure to keep the saw moving through the
work piece.
TO REMOVE BLADE:
• Turn the blade clamp to the right with fingers.
• Pull off blade.
9
10
• Mark out the line to be cut
so it is easily visible.
ACCESSORIES
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
• Start inside the area to be
cut out.
• Depress the lock-on button
and press the trigger to start
the saw.
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.
If you must use an extension cord, be sure that the gauge is large enough to carry
the amount of current necessary for your power tool. If not, your tool may
experience a loss of power, excessive voltage drop or overheating. The smaller the
gauge number, the heavier the cord (see table below).
• Set the shoe against the
work piece.
• When the blade reaches full
speed, slowly feed the blade
into the work piece.
RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS
TOOL CURRENT RATING
CONDUCTOR SIZE IN A.W.G
AMPERE
3-6
6-8
8-10
10-12
12-16
16-20
10FT.
18
18
18
16
25FT.
18
18
18
16
50FT.
18
18
18
14
100FT.
18
16
14
14
-
METAL CUTTING
Never use gasoline or any flammable liquid as a
lubricant. Sparking from the motor may cause it to ignite into flames.
14
12
12
12
12
12
OIL
-
• When cutting metals other then
copper, brass or aluminum,
always use a lubricant, such
as cutting oil, to keep the
blade cool. This
will prolong
MAINTENANCE AND CLEANING
Always UNPLUG the Reciprocating Saw from the power
source before inspecting, performing any maintenance or cleaning.
the life of the
blade as well
as speeding
up the cutting
process.
This Reciprocating Saw is lubricated before it leaves
the factory. This lubrication should last for the life of the tool. No further
lubrication is required.
• Make sure
the work
piece is held
securely in place.
Hold smaller pieces, such as pipe or conduit,
in a vise or attach to the workbench with clamps.
Use only mild soap and a damp cloth to clean the tool. Never let any liquid get
inside the casing. Never immerse any part of the tool in a liquid. Always keep the
ventilation openings clear.
Brushes will wear with use and should be inspected periodically by qualified
personnel.
• To eliminate vibration, always cut close to the clamping point.
Regularly clean the ventilation slots in your tool using only a soft brush or dry cloth.
• When cutting thin sheets of metal, place a piece of plywood on either side to control
vibration and prevent tearing.
Never open the Reciprocating Saw case. Do not attempt to repair the
Reciprocating Saw yourself. Opening the case will void your warranty.
11
12
SPECIFICATIONS
SPECIFICATIONS
2 YEAR LIMITED WARRANTY
Express and Exclusive Limited Warranty to Original Retail Buyer
Alltrade Tools LLC (hereinafter “Alltrade”) expressly warrants to the original retail
purchaser of the accompanying KAWASAKI™ portable power tool and no one else
all parts of the product (except those parts referred to below which are specifically
excluded from such warranty (see Exclusions) to be free from defects in materials
and workmanship for a period of two years from original date of purchase.
Voltage
120V
5.0A
18mm (3/4")
2500/min
60 Hz
Rated Current
Length of Stroke
No Load Speed
The date of purchase shall be the date of shipment to the original purchaser, or the
date the original purchaser took possession, custody or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
component thereof is modified or altered. This warranty does not apply to any other
product and/or component thereof manufactured or distributed by Alltrade, and
does not apply to products and/or components thereof designed, manufactured
and/or assembled by others, for which Alltrade makes no warranties whatsoever.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON
THE FACE HEREOF.
SERVICE
Use only authorized replacement parts for your tool.
Tool service must be performed only by qualified repair personnel using authorized
replacement parts. Service or maintenance by unqualified personnel could result in
considerable risk of personal injury. Use of unauthorized parts or failure to follow
maintenance instructions may create a risk of electric shock or injury.
Warranty Performance
By purchasing the product, purchaser expressly acknowledges and agrees that their
sole and exclusive remedy under this warranty shall be strictly limited to the repair
or replacement of any covered nonconforming items or parts thereof provided that
any such nonconforming item and/or part is promptly returned to Alltrade’s facility
postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair,
1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service #310-522-9008)
within the applicable warranty period, with a written request by purchaser that
Alltrade repair and/or replace the nonconforming item and/or part. We recommend
that you keep the original product packaging in the event you need to ship the unit.
We suggest the package be insured against loss or in transit damage. When
sending your product include your name, address, phone number, dated proof
of purchase (or copy), and a statement about the nature of problem. Warranty
coverage is conditioned upon purchaser furnishing Alltrade with adequate written
proof that they are the original purchaser and of the original purchase date. Parts
returned, freight prepaid and insured, to Alltrade’s facility (see above address) will
be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if
found to be defective and subject to warranty. Alltrade retains the sole discretion
to determine whether any item or part is nonconforming and, if so, whether the
item and/or part will be repaired and/or replaced. If the unit is repaired, new or
reconditioned replacement parts may be used. If Alltrade chooses to replace
the product, it may replace it with a new or reconditioned one of the same or
comparable design. The repaired or replaced unit will be warranted under the terms
of the remainder of the two year warranty period. Typically, a defective product that
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS
Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would
like further information on the following products, please contact Alltrade Customer
Service Department at 1-800-590-3723.
Cordless Drills/Screwdrivers
Impact Wrenches
Sanders
Jigsaws
Circular Saws
Angle Grinders
Reciprocating Saws
Routers
Rotary Tools
Corded and Cordless Multi-Purpose Tools
Wide Range of Accessories and more.
13
14
is returned within the first 30 days after the purchase date will be replaced; for items
returned after the first 30 days and within the two year warranty period, covered
defective parts not subject to normal wear and tear or other exclusions will be
repaired or replaced, at Alltrade’s option. During the warranty period, Alltrade will
be responsible for the return shipping charges. Alltrade’s repair and/or replacement
of any nonconforming item and/or part thereof shall constitute fulfillment of all
obligations to the purchaser. Alltrade shall not be responsible or liable for any
expense, including freight charges, or repairs made outside Alltrade’s facility, unless
expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade
bear any responsibility for loss of the unit, loss of time or rental, inconvenience,
commercial loss or consequential damages.
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY
WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR
CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER’S
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.
EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE
WARRANTY IS MADE WITH REGARD TO THIS PRODUCT. ALL EXPRESS AND/OR
IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE
AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE,
PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT
THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY,
GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY
OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF
ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY
EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH
WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING
THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE
REMEDY IS AS STATED ABOVE.
Exclusions
This warranty does not cover parts damaged due to normal wear, abnormal
conditions, misapplication, misuse, abuse, accidents, operation at other than
recommended pressures or temperatures, improper storage or freight damage.
Parts damaged or worn by operation in dusty environments are not warranted.
Failure to follow recommended operating and maintenance procedures also
voids warranty.
This limited warranty does not apply to accessory items such as drill bits,
screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding
sheets and other related items.
DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY,
USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES,
COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO
PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS
WARRANTY.
Limitation Of Liability
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH
OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS
REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER,
AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR
OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS
REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH
DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL
ALLTRADE’S AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF
THE PRODUCT. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF
THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY
PERIODS SPECIFIED ABOVE.
Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons;
pre-delivery services such as assembly, oil or lubricants, and adjustment;
maintenance services that are normally required to maintain the product.
The use of other than genuine Alltrade Repair Parts will void warranty.
Warranty Disclaimers
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES,
GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY
PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR
REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF
15
16
Limitations on Warranty Disclaimers
Some states do not allow limitations on how long an implied warranty lasts
and some states do not allow the exclusion or limitation of the incidental or
consequential damages, so part or all of the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
If your product is not covered by this warranty, please call our Customer Service
Department at 1-310-522-9008 or toll free at 1-800-590-3723 for general repair
information and charges.
17
18
|