K 2.20 M
English
Español
Français
2
59634730 08/09
MODEL OVERVIEW
1 Swivel casters
2 ON/OFF switch
9 Wheels
10 Trigger gun
3 Detergent suction tube with filter
4 High pressure outlet
5
11 Trigger gun safety lock
12 Locking slide for high pressure hose
13 High pressure hose
6 Spray Wand Storage
7 Water inlet with garden hose connec-
tor
14 Spray wand
®
15 Dirtblaster (Rotary spray wand)
®
16 VELCRO fastener
8 Power cord with Ground Fault Circuit
Interrupter (GFCI)
English 3
IMPORTANT SAFETY INSTRUCTIONS
physical injuries to the operator and
irreversible damage to the machine.
ƽ WARNING
When using this product basic precau-
tions should always be followed, includ-
ing the following:
ƽ CAUTION
Gun Kicks Back – Hold with both
hands.
„ Read all the instructions before using
the product.
„ To reduce the risk of injury, close su-
pervision is necessary when a prod-
uct is used near children.
„ Know how to stop the product and
bleed pressures quickly. Be thor-
oughly familiar with the controls.
„ Stay alert – watch what you are do-
ing.
„ The Trigger Gun Safety Lock pre-
vents the trigger from accidentally
being engaged. This safety feature
DOES NOT lock trigger in the ON po-
sition.
ƽ WARNING – Risk of Electrocution
„ Inspect cord before using – Do not
use if cord is damaged.
„ Keep all connections dry and off the
ground.
„ Do not operate the product when fa-
tigued or under the influence of alco- „ Do not touch plug with wet hands.
hol or drugs.
„ Do not use extension cord with this
„ Keep operating area clear of all per-
sons.
product.
„ Connect to individual branch circuit
„ Do not overreach or stand on unsta-
ble support. Keep good footing and
balance at all times.
only.
ƽ CAUTION
This unit has been designed for use with
„ Follow the maintenance instructions cleaning detergents recommended by
specified in the manual.
the manufacturer. The use of other
„ This product is provided with a
cleaning detergents may affect the oper-
Ground Fault Circuit Interrupter built ation of the machine and void the war-
into the power cord plug. If replace-
ment of the plug or cord is needed,
use only identical replacement parts. „ DO NOT SPRAY ELECTRICAL APPA-
ranty.
ƽ WARNING
RATUS AND WIRING.
„ DO NOT USE WITH FLAMMABLE
ƽ WARNING
Risk of Injection or Injury – Do Not
Direct Discharge Stream At Persons.
LIQUIDS AND TOXIC CHEMICALS.
„ High pressure jets can be dangerous „ HIGH PRESSURE. KEEP CLEAR OF
if misused. The jet must not be di- NOZZLE.
rected at persons, animals, electrical „ INJECTION HAZARD: EQUIPMENT
devices, or the unit itself.
„ Wear safety goggles.
CAN CAUSE SERIOUS INJURY IF
THE SPRAY PENETRATES THE
SKIN. DO NOT POINT THE GUN AT
ANYONE OR ANY PART OF THE
BODY. IN CASE OF PENETRATION
SEEK MEDICAL AID IMMEDIATELY.
„ THIS SYSTEM IS CAPABLE OF PRO-
DUCING 1600 PSI TO AVOID RUP-
ƽ WARNING
Risk Of Explosion – Do not spray
flammable liquids.
„ Do not use acids, alkaline, solvents,
or any flammable material in this
product. These products can cause
4 English
TURE AND INJURY, DO NOT
OPERATE THIS PUMP WITH COM-
become necessary, use only identical
replacement parts that include GFCI
PONENTS RATED LESS THAN 1600 protection.
PSI WORKING PRESSURE (INCLUD-
ING BUT NOT LIMITED TO SPRAY
WATER SUPPLY
(Cold Water Only)
GUNS, HOSE AND HOSE CONNEC-
TIONS).
„ BEFORE SERVICING, CLEANING
OR REMOVING ANY PARTS, SHUT
OFF POWER AND RELIEVE PRES-
SURE.
„ IF CONNECTION IS MADE TO A PO-
TABLE WATER SYSTEM, THE SYS-
TEM SHALL BE PROTECTED
AGAINST BACKFLOW.
ƽ CAUTION
When connecting the water inlet to the
water supply mains, local regulations of
your water company must be observed.
In some areas the unit must not be con-
nected directly to the public drinking wa-
ter supply. This is to ensure that there is
no feedback of chemicals into the water
supply. Direct connection via a receiver
tank or backflow preventer, for example,
is permitted.
SERVICING OF A DOUBLE-
INSULATED PRODUCT
Dirt in the feed water will damage the
unit. To avoid this risk, we recommend
fitting a water filter.
„ Garden hose must be at least 1/2
inch or 5/8 inch in diameter.
In a double-insulated product, two sys-
tems of insulation are provided instead
of grounding. No grounding means is
provided on a double-insulated product,
nor should a means for grounding be
added to the product. Servicing a dou-
ble-insulated product requires extreme
„ Flow rate of water supply must not
fall below 2 GPM (gallons per
minute).
care and knowledge of the system, and „ Flow rate can be determined by run-
should be done only by qualified service
personnel. Replacement parts for a dou-
ble-insulated product must be identical
to the parts they replace. A doubleinsu-
lated product is marked with the words
“DOUBLE INSULATION” or “DOUBLE
INSULATED”. The symbol “ ” may also
be marked on the product.
ning the water for one minute into an
empty 5-gallon container.
„ The water supply temperature must
not exceed 104°F/40°C.
„ Never use the pressure washer to
draw in water contaminated with sol-
vents, e.g. paint thinners, gasoline,
oil, etc.
„ Always prevent debris from being
drawn into the unit by using a clean
water source.
GROUND FAULT CIRCUIT INTER-
RUPTER PROTECTION
This pressure washer is provided with a
ground-fault circuit-interrupter (GFCI)
built into the plug of the power-supply
cord. This device provides additional
protection from the risk of electric shock.
Should replacement of the plug or cord
SAVE THESE INSTRUCTIONS!
English 5
ASSEMBLY INSTRUCTIONS
Î STEP 3:
Required tools
®
Fix the VELCRO fastener to the ap-
pliance.
Screwdriver, small size (not supplied)
for connecting high pressure hose and
trigger gun.
Î STEP 4:
A Pull out the locking slide of the trigger
gun handle.
Assembly
B Insert the small end of the high pres-
sure hose into place.
C Push the locking slide back into the
trigger gun to lock the hose in posi-
tion.
Î STEP 1:
Insert the steering rollers and lock
them.
Î STEP 2:
Insert wheels into the side holes of
the unit.
OPERATING INSTRUCTIONS
Î STEP 1:
Connect the high pressure hose to
the unit’s high pressure outlet.
Î STEP 2:
Insert the spray wand of your choice
into the trigger gun. Press in against
the spring tension and twist into
locked position.
6 English
Î STEP 3:
Connect garden hose to unit’s water
Î STEP 6:
Unlock the trigger gun safety lock.
inlet.
Trigger the gun to eliminate trapped
air, wait for a steady flow of water to
emerge from the spray nozzle.
Î STEP 4:
Connect garden hose to the cold wa-
ter source and turn water on com-
pletely.
Î STEP 7:
Turn on the high pressure washer (I/
ON).
The motor starts only if the trigger
of the gun is pulled and shuts off
when the trigger is released.
Î STEP 5:
Plug the Ground Fault Circuit Inter-
rupter (GFCI) into a working outlet.
We recommend that you test the GFCI as
part of your startup procedure each time
you use your pressure washer. To learn
how to peform this test on your unit, visit
gfci_test.php for detailed instructions for
your type of GFCI.
ƽ WARNING
Do not use if above test fails.
Note: The actual appearance of the GFCI may be
different from this illustration.
English 7
USING THE ACCESSORIES
ƽ WARNING
Dirtblaster®
To avoid serious injury never point
spray nozzle at yourself, other per-
sons or animals.
„ This nozzle features a 0º pencil jet
which rotates 360º for maximum dirt
cutting action, effectively increasing
cleaning performance up to 50%.
This nozzle combines the cleaning
performance of a 0º pencil jet with
the surface coverage of a wide angle
nozzle.
Always test an inconspicuous area
before cleaning with high pressure.
Spray wand
This nozzle features a steady powerful
high pressure spray pattern, for general
cleaning.
Not recommended for soft materi-
als, siding, painted surfaces,
decks or autos.
„ Before cleaning any surface an in-
conspicuous area should be cleaned
to test spray pattern and distance for
maximum cleaning results.
8 English
WORKING WITH DETERGENTS
Detergents can only be applied at low For best results see Cleaning Tips for
pressure.
specific information on how to clean
different surfaces.
A low-pressure jet is generated if no
spray wand is attached to the trigger
gun.
®
Always Use Kärcher Detergent for
Î STEP 1:
Best Results
Kärcher biodegradable detergents are
®
Fill a container with Kärcher deter-
gent. Place the filter end of detergent specially formulated to protect the envi-
suction tube into the container.
ronment and your pressure washer. The
special formula won’t clog the suction
tube filter and will protect the internal
parts of the pressure washer for a longer
®
life. For Kärcher Detergents, check
your retailer or visit our website:
ƽ CAUTION
Î STEP 2:
Never use:
Detach spray wand from the trigger
gun.
Î STEP 3:
– Bleach, Chlorine products and other
corrosive chemicals
– Liquids containing solvents (i.e.,
paint thinners, gasoline, oils)
– Tri-sodium phosphate products
– Ammonia products
Turn on the pressure washer (I). Pull
trigger to operate unit. Liquid deter-
gent is drawn into the unit and mixed
with water. Apply detergent to work
area. Do not allow detergent to dry
on surface.
– Acid-based products
These chemicals will harm the unit and
will damage the surface being cleaned.
Use of these items will void the war-
ranty.
Î STEP 4:
To rinse, insert the spray wand and
pull trigger to operate unit.
Î STEP 5:
Cleaning up: Always draw fresh wa-
ter through the detergent tank or si-
phon tube when done to flush any
remaining detergents from the injec-
tion system.
English 9
TAKING A BREAK ..five minutes or more
Î STEP 1:
Release trigger and engage gun
safety lock.
Î STEP 2:
Turn pressure washer to OFF (0) po-
sition.
SHUTTING DOWN & CLEAN-UP
Î STEP 1:
Turn the switch to OFF (0) position
and unplug cord from outlet.
Î STEP 5:
Disconnect the garden hose from the
water inlet on the unit.
Î STEP 6:
Î STEP 2:
Turn off the water source.
Î STEP 3:
Disconnect the high pressure hose
from the high pressure outlet.
Press trigger to release water pres-
sure.
Î STEP 7:
Engage the spray lance in its com-
partment.
Î STEP 4:
Store coiled power cord, coiled high
pressure hose and handgun with the
VELCRO fastener on the appliance.
Release trigger and engage gun
safety lock.
®
10 English
WINTERIZING AND LONG-TERM STORAGE
Î 1: Disconnect all water connections.
Î 2: Turn on the machine for a few sec- Failure to follow the above directions will
ƽ CAUTION
onds, until the water which had re-
mained in the pump exits, turn off
immediately.
result in damage to the pump assembly
and accessories and will void the war-
ranty.
®
Î 3: Do not allow high pressure hose to Kärcher also recommends the regular
become kinked.
practice of using a pump protector like
“Kärcher Pump Guard” to prevent cold
weather damage during storage in the
winter months.
®
Î 4: Store the machine and accesso-
ries in a room which does not reach
freezing temperatures. DO NOT
store near furnace or other sources
of heat as it may dry out the pump
seals.
CARE AND MAINTENANCE INSTRUCTIONS
Cleaning the water inlet filter
Maintenance
Î STEP 1:
The unit is maintenance-free.
Pull out washer from the water inlet.
Î STEP 2:
Pull out water inlet filter with flat-nose
pliers.
Î STEP 3:
Rinse out water inlet filter in warm
water.
Î STEP 4:
Reinsert water inlet filter and washer
into the water inlet.
English 11
CLEANING TIPS
6 feet and always apply detergent from
bottom to top). Allow detergent to re-
ƽ CAUTION
„ Before cleaning any surface an in-
conspicuous area should be cleaned main on surface 1-3 minutes. Do not al-
to test spray pattern and distance for low detergent to dry on surface, if
maximum cleaning results.
„ If painted surfaces are peeling or
chipping, use extreme caution as
pressure washer may remove the
loose paint from the surface.
surface appears to be drying, simply wet
down surface with fresh water. If need-
ed, use special wash brush attachment
(not included) to remove stubborn dirt.
Rinse at high pressure from top to bot-
„ When using on surfaces which might tom in an even sweeping motion keep-
come in contact with food, flush sur- ing the spray nozzle approximately
faces with plenty of drinking water.
„ For additional cleaning tips and a
complete video library, visit our web-
site:
6 inches from the cleaning surface.
Cement Patios, Brick and Stone
(with or without detergent). Pre-rinse
cleaning surface with fresh water. If us-
ing detergent or Degreaser, apply to
surface at low pressure. For best re-
sults, limit your work area to smaller sec-
tions of approximately 25 square feet.
Allow detergent or Degreaser to remain
on surface 1-3 minutes. Do not allow de-
tergent to dry on surface. Rinse at high
pressure in a sweeping motion keeping
Deck Cleaning
(with or without detergent). Pre-rinse
deck and surrounding area with fresh
water. If using detergent, apply to sur-
face at low pressure. For best results,
limit your work area to smaller sections
of approximately 25 square feet. Allow
detergent to remain on surface 1-3 min- the spray nozzle approximately 3-6
utes. Do not allow detergent to dry on inches from the cleaning surface. Al-
surface. Rinse at high pressure in a long ways clean from top to bottom and from
sweeping motion keeping the spray noz- left to right. For removing extremely
®
zle approximately 3-6 inches from the
stubborn stains, use the Dirtblaster
cleaning surface. Always clean from top Nozzle.
to bottom and from left to right. When
Cars, Boats & Motorcycles
moving on to a new section of the clean-
ing surface, be sure to overlap the previ-
ous section to eliminate stop marks and
ensure a more even cleaning result.
(with or without detergent). Pre-rinse
vehicle with fresh water. If using deter-
gent, apply to surface at low pressure.
For best results, clean one side of vehi-
cle at a time and always apply detergent
from bottom to top, do not allow deter-
House Siding
(with or without detergent). Pre-rinse
cleaning surface with fresh water. If us- gent to dry on surface. If needed, use
ing detergent, apply to surface at low
pressure (for best results, limit your
work area to sections of approximately
special wash brush attachment (not in-
cluded) to remove stubborn dirt. Rinse
at high pressure in a sweeping motion
12 English
keeping the spray nozzle approximately tremely stubborn dirt, it may be neces-
6-8 inches from the cleaning surface sary to move the spray nozzle even
(distance should increase when rinsing closer to the surface for greater dirt cut-
pin-striping or other sensitive surfaces). ting action.
Always clean from top to bottom and
Patio & Lawn Furniture
from left to right. For best results, wipe
surface dry with a chamois or soft dry
cloth.
(with or without detergent). Pre-rinse
furniture and surrounding area with
fresh water. If using detergent, apply to
surface at low pressure. Allow detergent
to remain on surface 1-3 minutes. Do
not allow detergent to dry on surface. If
Barbecue Grills, Outdoor Power
Equipment & Gardening Tools
(with or without detergent). Pre-rinse
cleaning surface with fresh water. If us- needed use special Wash Brush Attach-
ing detergent or Degreaser, apply deter- ment (not included) to remove stubborn
gent at low pressure. Allow detergent to dirt. Rinse at high pressure in a sweep-
remain on surface 1-3 minutes. Do not
ing motion keeping the spray nozzle ap-
allow detergent to dry on surface. Rinse proximately 3-6 inches from the
at high pressure keeping the spray noz- cleaning surface. For best results, clean
zle approximately 3-6 inches from the
cleaning surface. For removing ex-
from top to bottom and from left to right.
OPTIONAL CLEANING ACCESSORIES
Optional accessories are available to
further enhance your cleaning capabili-
ties. These accessories are accurate as
of the printing date of this manual.
25 Ft. Extension /Replacement
High-Pressure Hose
®
Replacement hose fits Kärcher pres-
Please check our website for pricing and sure washer with screw-on type gun
up-to-date information.
connections from 2400 PSI to 2500 PSI,
Extension Hose for all Kärcher high
®
Pump Guard
pressure washers between the original
equipment hose and machine up to
2500 PSI.
Specially formulated to protect your
pressure washer from freezing, corro-
sion and premature wear. The Pump
Guard also adds lubrication to valves
and seals to prevent sticking. Highly rec-
Part No. 2.640-850.0
66" Extension Wand (Four piece)
®
ommended for all Kärcher pressure
Need to clean second story windows or
other high areas? Increase the reach of
your pressure washer by up to 66" with
this extension kit. Includes 4 aluminum
sections for variable length. 66" fully as-
washers!
Part No. 9.558-998.0
®
sembled. Fits most Kärcher pressure
washers up to 2300 PSI. (bayonet)
Part No. 2.640-746.0
English 13
Rotating Wash Brush (bayonet)
Wet Sandblasting Kit (bayonet)
For more effortless cleaning of all
Why spend hours stripping old paint and
smooth surfaces (painted, glass and
plastic) try the Kärcher Rotating Wash the Kärcher Wet Sandblasting Kit do
Brush. Use it on your automobile, house the work! Attach the kit to your pressure
rust by hand using harsh chemicals? Let
®
®
siding or windows. The water pressure
from your pressure washer causes the
inner brushes to gently spin, making
washer, add abrasive material and at-
tack the rust and paint with our eco-
friendly alternative. Fits most Kärcher
®
your cleaning job much easier. The an- pressure washers up to 2300 PSI. (bay-
gle of brush head is adjustable to help
you reach difficult areas. Excellent for
the application of detergent. A must-
onet)
Part No. 2.638-792.0
®
Detergent Foamer Attachment
have accessory designed for Kärcher
pressure washers up to 2300 PSI. (bay-
onet)
Part No. 2.640-743.0
Ideal for applications which require a
thick foam. Simply fill the resevoir cup
with liquid pressure washer detergent to
generate a foam spray. Connects direct-
Soft Clean Washing Brush
®
ly to the trigger gun. Fits most Kärcher
Made with soft bristles that will not harm pressure washers up to 2300 PSI. (bay-
painted surfaces. Easily attaches direct- onet)
ly to the trigger gun. Ideal for stubborn
dirt on cars, boats, patio furniture and
other surfaces. Great for applying deter-
gent. Fits most Kärcher pressure wash-
ers up to 2300 PSI. (bayonet)
Part No. 6.964-507.0
T 100 Wide Area Surface Cleaner
®
For cleaning surfaces such as patios,
terraces and driveways without splash-
back, there is no better solution than the
Part No. 2.640-740.0
®
Kärcher T 100. It saves time by clean-
25 ft. Pipe Cleaning Kit (bayonet)
ing a one foot wide area gently as it hov-
ers, providing consistent, streak-free
Need to clean blocked pipes, drains or
®
downspouts? The Kärcher pipe clean- cleaning. When you finish cleaning the
ing kit is the answer! The pipe cleaner
propels itself forward while simulta-
neously flushing out debris. For exam-
ple, insert the cleaning nozzle in the
patio and driveway, remove the wand
and use the handle to clean garage
doors and other vertical surfaces. In-
cludes two nozzles which spin at high
base of a downspout, pull the trigger on speed for optimum results. Our top sell-
®
the pressure washer gun and watch as
the nozzle shoots out leaves and other
ing accessory for Kärcher pressure
washers up to 2300 PSI. (bayonet)
debris while climbing upward. Connects Part No. 2.640-959.0
directly to the trigger gun of most
®
Kärcher pressure washers up to
2300 PSI. (bayonet)
Part No. 2.640-747.0
14 English
TROUBLESHOOTING
ƽ CAUTION
Disconnect the machine from the power
source before making any repair.
Symptom
Motor will not start On/Off switch is in the “OFF” Turn switch to the “ON” (I) po-
(0) position. sition
Power cord is not plugged in. Plug in power cord.
Cause
Solution
Electrical outlet does not
supply adequate power.
Try a different outlet.
Tripped GFCI plug.
Press “RESET” button on
GFCI plug.
Tripped circuit breaker.
Switch off pressure washer.
The reset comes automatically
once the temperature of the
unit drops.
Unit does not
reach high
pressure.
Diameter of garden hose is too Replace with a 5/8 inch or larg-
small.
er garden hose.
Water supply is restricted.
Check garden hose for kinks,
leaks and blockage.
Not enough inlet water supply. Open water source full force.
Water inlet filter is clogged.
Remove filter and rinse out in
warm water.
Spray wand is on low pressure Turn spray wand to high pres-
position. sure position.
Output pressure Not enough inlet water supply. Turn water on full force. Check
varies high and
low.
garden hose for kinks, leaks or
blockage.
Pump is sucking air.
Check that hoses and fittings
are air tight. Turn off machine
and purge pump by squeezing
trigger gun until a steady flow
of water emerges through the
nozzle.
Water inlet filter is clogged.
Remove filter and rinse out in
warm water.
Discharge nozzle is
obstructed.
Blow out or remove debris with
a fine needle.
Calcified gun, hose or spray
wand.
Run distilled vinegar through
detergent suction tube.
English 15
Symptom
Cause
Solution
No detergent.
Detergent suction tube not
properly connected to the
machine.
Check connection.
Detergent is too thick.
Dilute detergent, for best re-
sults use Kärcher detergent.
®
Filter on detergent suction
tube is clogged.
Run warm water through filter
to remove debris.
Damaged or clogged
detergent suction tube.
Remove obstruction or replace
detergent suction tube.
Spray wand fitted.
Remove spray wand.
Discharge nozzle is
obstructed.
Blow out or remove debris with
fine needle.
Garden hose
Loose fittings.
Tighten fittings.
connection leaks.
Missing/worn rubber washer. Insert new washer.
Spray wand leaks. Spray wand not properly
attached.
Insert the spray wand into the
trigger gun. Carefully press in
against the spring tension and
twist into the locked position.
Broken o-ring or plastic insert. Call Customer Support
Pump is noisy.
Pump is sucking air.
Check that hoses and fittings
are air tight. Turn off machine
and purge pump by squeezing
trigger gun until a steady flow
of water emerges through the
nozzle.
Water leaks from Loose fittings.
Check that all fittings are tight.
pump (up to 10
drops per minute
is permissible).
Water seals are damaged or Call Customer Support
worn.
Oil Drip.
Oil seals are damaged or
worn.
Call Customer Support
If you encounter any additional difficul-
ties not listed, please visit our website.
USA / Canada:
México:
16 English
|