TurboTwister Bagless
Vacuum Cleaner
KBV70
Download from Www.Somanuals.com. All Manuals Search And DownloadI. ssue 02/08
fEATURES Of YOUR KAMBROOK
JAGUAR VACUUM CLEANER
1
2
3
4
8
5
1.Powerful 2000 watt motor for superior
suction and fast and effective cleaning
6.Quality turbo brush floor tool ideal for
carpet and hard floors
2.Bagless canister for easy removal of dirt and
7.Telescopic chrome steel wand is easily
extendable or retractable for varying height
requirements
dust with no need for replacement bags
3.4 stage HEPA filtration system filters dust
particles including mites, pollen, fungus,
spores and most air suspended particles
at 98% efficiency. Ideal for allergy sufferers
8.Multi-Terrain floor tool for cleaning carpets.
4.Horizontal parking for easy and convenient
storage
5.Crevice and brush tools ideal for picking up
dust from hard to reach places
ꢁ
VARIABLE POWER CONTROL
USING YOUR KAMBROOK JAGUAR
VACUUM CLEANER
The power booster dial on the unit is to be
used for variable power control. Turn the
control clockwise for maximum power for
vacuuming hard floor and carpet surfaces.
Turn the control anti-clockwise for
minimum power when using the crevice
and brush tools.
When unpacking the vacuum cleaner unit
check to see you have received all the
required components, such as the hose
and other accessories before discarding
the packaging.
Ensure that the dust container and filters are
correctly fitted.
Locate the crush proof hose and push
the connection point into the hose inlet
connection on the front side of the unit, until
a “click” sound is heard.
Connect the wide end of the metal wand to
the hose end, and push together firmly.
Fit the floor tool to the narrow end of the
wand and push together firmly.
Fully extend the power cord by pulling the
power plug (situated at the rear of the unit)
out from the unit, until the yellow tape on the
cord is shown.
TURBO BRUSH
The Turbo Twister Brush is a floor tool
which has been specifically designed to work
in conjunction with your KBV70 Jaguar Turbo
Twister Bagless Vacuum Cleaner. While
regular floor tools do a good job at cleaning
surfaces the Turbo Brush is the ideal way to
clean away those hard to see dust and dirt
particles that are trapped deep within carpet
pile.
ENSURE THAT YOU DO NOT OVER
EXTEND THE POWER CORD – DO NOT
EXTEND PAST THE RED WARNING TAPE
ON THE CORD
Plug into a 230/240v power point and switch
the power on.
To commence vacuuming push down on the
on/off button at the top of the unit.
Fit the Turbo Brush onto the telescopic wand
and follow the regular starting procedure and
commence vacuuming. The suction of the
cleaner starts a curved row of bristles in the
brush rotating at high speed. These rotating
bristles actively work to dislodge deep pile
debris to provide a more effective surface
clean.
When vacuuming is complete, push down on
the ‘on/off’ button to switch off. Turn the
power off at the outlet and then remove the
power cord from the power outlet. When
removing plug from the power outlet grasp
the plug not the cord.
To retract the cord push down on the ‘cord
rewind’ to retract the cord.
The Turbo Brush has been specifically
designed for removing dirt and debris from
carpeted surfaces. Do not use it for any
purposes, other than those stated. For
optimal performance of your Turbo Brush
ensure that the bristles are kept clean after
use.
IMPORTANT: HOLD THE PLUG END
WHEN RETRACTING THE CORD TO
PREVENT IT FROM STRIKING YOU OR
THE VACUUM.
CAUTION: ALWAYS ENSURE THAT
THE DUST CONTAINER AND THE MOTOR
PROTECTION FILTER ARE CORRECTLY
FITTED. NEVER OPERATE WITHOUT
THE DUST CONTAINER AND FILTERS
IN PLACE.
CLEAN THE FLOOR TOOLS SECTION
REGULARLY REMOVE HAIR, COTTON ETC
FROM THE TURBO BRUSH HEAD. CUT
ACROSS THE HAIR ETC AND GENTLY
PULL FREE.
ꢂ
CREVICE AND BRUSH TOOL
ACCESSORIES
Once released slowly pull the container
upwards.
The crevice tool is ideal for vacuuming hard to
reach places such as the edges along skirting
boards.
The brush tools can be used to vacuum
delicate surfaces and areas such as shelves and
venetian blinds.
Set the variable speed control between
minimum and medium power when using the
tool accessories.
Turn off the vacuum cleaner when changing
any attachments.
DUST CONTAINER INDICATOR AND
DISPENSING THE DUST CONTAINER
To empty the dust container simply place
it above the rubbish bin, press the “push to
empty” button. The bottom of the container
will release and the dust and compiled dirt
will be dispensed.
The dust container should be emptied when
the dust and dirt reaches the MAX level.
Always switch the appliance off, then switch
off at the power outlet and unplug the
appliance prior to replacing filters or emptying
the dust container.
IMPORTANT: DO NOT USE THE UNIT
WITHOUT A DUST CONTAINER
IN PLACE
To remove the dust container, ensure the
unit is down on its wheels; remove the dust
container by pressing the “press and lift”
button on the dust container.
ꢃ
MOTOR PROTECTION fILTER
CLEANING AND REPLACING
fILTERS
The motor protection filter must always be in
place when operating the vacuum otherwise
damage to the motor may occur.
Filters must be cleaned from time to time (at
least twice a year) to remove the fine dust
particles that have been collected.
To replace the motor protection filter
- remove the dust container. The motor
protection filter is located at the bottom of
the inner chamber. Pull the filter upward to
remove then simply replace the new filter.
1. Remove the dust container from the unit
by pressing down on the “Press and llift”
button
2. After removing the dust container, hold
steadily on the dust container and twist the
lid clockwise until ‘click’ sound is heard and
the lid of the dust container is detached.
EXHAUST fILTER
The exhaust filter should be cleaned every
six months. Simply unclip the grill at the back
of the vacuum cleaner and shake and tap the
filter to remove any dust accumulated. Then
relocate the filter and reattach the grill.
3. Take off the combined mesh and HEPA
filter by holding steady on the lid of the dust
canister and twisting the combined mesh
and HEPA filter anti-clockwise
CARE AND MAINTENANCE
4. Tap and shake the filter until all the fine
dust particles are removed. However, after
approximately 6 months the filter should be
replaced.
Always switch appliance off, then switch off
at the power outlet and unplug the appliance
prior to cleaning or replacing either filter.
To clean the outside of the unit, wipe the
exterior with a soft, damp cloth. Never use
an abrasive cleaner.
5. To place the filter back in the dust canister
simply place the combined mesh and HEPA
filter in the dust container lid and turn the
filter in a clockwise direction until ‘click’
sound is heard to lock it in place.
CHECK AND REPLACE BOTH THE
MOTOR PROECTION AND HEPA FILTERS
APPROXIMATELY TWICE A YEAR OR
WHEN VISIBLY CLOGGED
6. To fully assembled the dust filter unit,
simply placed the combined filter and lid
together with the dust container. Hold
steady on the dust container and twist
the lid in anti-clockwise direction until it’s
clicked in place.
7. Place the complete dust container assembly
back in the vacuum cleaner for next use.
Ensure the bottom of the dust container is
closed prior to replacing the dust container.
ꢄ
NOTES
ꢅ
KAMBROOK 12 MONTH REPLACEMENT WARRANTY
Kambrook warrants the purchaser against defects If the product includes one or a number of
in workmanship and material for a period of 12 accessories only the defective accessory or
months from the date of purchase (3 months product will be replaced.In the event of Kambrook
commercial use).
choosing to replace the appliance, the guarantee
will expire at the original date, i.e. 12 months from
the original date of purchase.
Guarantee and purchase receipt for this product
are to be retained as proof of purchase and must be
presented if making a claim under the Kambrook In Australia, this KAMBROOK Guarantee is
guarantee.
additional to the conditions and guarantees which
are mandatory as implied by the Trade Practises
Act 1974 and State andTerritory legislation.
Kambrook reserves the right to replace or repair
the appliance within the warranty period.
For service, spare parts or product information
in Australia, please call KAMBROOK on the
Customer Service Line; 1300 139 798.
Warranty does not apply to any defect,
deterioration, loss, injury or damage occasioned
by, or as a result of the misuse or abuse, negligent
handling or if the product has not been used in For service, spare parts or product information
accordance with the instructions. The guarantee in New Zealand, please call KAMBROOK New
excludes breakages.
Zealand; 0800 273 845.
This warranty is void if there is evidence of the If claiming this guarantee the product must be
product being tampered with by unauthorised returned freight prepaid.
persons.
KAMBROOK 12 MONTH REPLACEMENTWARRANTY
Attach a copy of the purchase receipt here.
YOUR PURCHASE RECORD (Please complete)
DATE OF PURCHASE
MODEL NUMBER
SERIAL NUMBER
(Please don’t return purchase record until
you are making a claim)
PURCHASED FROM
Kambrook - Australia
Building 2, Port Air Industrial Estate 1A Hale Street, Botany NSW 2019,Australia
Customer Service Line 1300 139 798
Customer Service Fax 1800 621337
Kambrook - New Zealand
Private Bag 94411, Greenmount,Auckland, New Zealand
Customer Service Line/Spare Parts 09 271 3980
Customer Service Fax 0800 288 513
Due to continual improvement in design or otherwise, the product you purchase may differ slightly from the illustration in this book. Issue 2/08
|