Instruction Manual
Table of Contents
SECTION
PAGE #
SECTION 1: IMPORTANT SAFEGUARDS
SECTION 2: UNPACKING
1
3
SECTION 3: TOTAL BLENDER OVERVIEW
SECTION 4: INSTALLATION
4
4
SECTION 5: CARE AND CLEANING
SECTION 6: OPERATIONAL OVERVIEW
SECTION 7: TROUBLESHOOTING
SECTION 8: WARRANTY
6
7
8
10
1.8 NEVER OPERATE THE BLENDER USING ATTACHMENTS NOT SOLD
BY BLENDTEC
SECTION 2
The use of any unauthorized attachments may cause fire, electric shock, and/or
injury and will void the warranty.
SAVE ALL PACKAGING MATERIALS AND INSTRUCTIONS FOR FUTURE
USE.
1.9 CONTAINER MUST BE PROPERLY IN PLACE WHILE APPLIANCE IS
OPERATING
2.1 UNPACKING YOUR BLENDER
You should have received the following items:
• TOTAL BLENDERTM motor base
• Blender jar with lid
1.10 BLADES ARE SHARP! HANDLE CAREFULLY!
• Recipe book
1.11 WHEN BLENDING HOT LIQUIDS, REMOVE CENTER PIECE OF LID
1. Remove blender motor, blender jar and lid from packaging.
2. Unwind the power cord.
3. Check for any packing material that may have blocked ventilation holes in
the blender motor.
4. Inspect all items to ensure no damage occurred in shipment.
5. If any damage has occurred contact your Blendtec service agent
immediately.
1.12 POWER CORD PRECAUTIONS
• NEVER operate with a damaged cord or plug. (If the supply cord is damaged
it must be replaced by the manufacturer, or authorized service agent to avoid
a hazard
• DO NOT permit the cord to hang over the edge of the work surface.
• NEVER use an extension cord with the unit.
• Unplug the blender motor when not in use; before changing blender loca-
tions; or cleaning.
2.2 RECORDING YOUR SERIAL NUMBER AND DATE OF PURCHASE
1.13 NEVER ATTEMPT TO REPAIR THE POWER UNIT
Never remove the blender motor cover. The blender motor does not contain self-
adjustable or serviceable parts. A qualified service agent must make all service
adjustments. Removing the cover or attempting to service the blender will void
the warranty.
Record your blender motor serial number and date of purchase in the space
below. You will need these when contacting Blendtec for service or questions.
Motor Serial #:
____________________________________________________
(Found on bottom of motor base)
1.14 TURN THE POWER SWITCH OFF WHEN NOT IN USE
The Power Switch (ON/OFF switch) is located on the back of the blender motor
cover.
Date of Purchase:
1.15 AVOID TOUCHING THE BLENDER DRIVE SOCKET AFTER EXTENSIVE
USE.
____________________________________________________
The blender drive socket may become hot after numerous cycles.
Purchased From
1.16 CLOSE SUPERVISION IS NECESSARY WHEN APPLIANCE IS USED BY
OR NEAR CHILDREN.
____________________________________________________
1.17 THE TOTAL BLENDER IS INTENDED FOR HOME USE ONLY! ANY USE
OF THE TOTAL BLENDERTM FOR COMMERCIAL PURPOSES VOIDS ALL
WARRANTIES.
2.3 REGISTRATION OF YOUR BLENDER
under the Support button) or return the registration card to the address provided.
SAVE THESE INSTRUCTIONS
TB-2
TB-3
SECTION 3
TOTAL BLENDER OVERVIEW
(Refer to Figures 1 and 2)
3.1 BLENDER MOTOR
• Motor Cover: Houses the power unit in a durable, easy-to-clean
polycarbonate.
• Touch Pad: Consists of six buttons that contain pre-programmed settings for
selective blender control, a pulse button, and two speed control buttons.
• LCD Information Center: will indicate status of unit as well as overload or
over-temperature conditions.
• Power Unit: This unit is located within the blender motor and contains the
machinery that runs the blender.
• Power Switch: Located on the back lower-right corner of the power unit.
3.2 BLENDER JAR ASSEMBLY
The blender jar assembly consists of the blender jar, blade assembly, and lid.
• Jar: Made from polycarbonate to provide maximum efficiency and clear
visibility of blender performance.
• Blade Assembly: Stainless steel designed to provide fast consistent blending
SECTION 4
INSTALLATION
We recommend that surge protection be placed between the receptacle and the
blender motor.
TOTAL BLENDER INSTALLATION
1. Place blender on a flat, clean and dry surface.
2. Make sure a plug outlet is available within four feet of the blender motor.
3. Ensure that the unit is turned off before plugging it into a separate 120-volt
receptacle.
4. Ensure that blender vents are unobstructed to allow proper cooling during
use.
TB-4
TB-5
SECTION 5
SECTION 6
CARE AND CLEANING
OPERATIONAL OVERVIEW
5.1 AFTER USE CLEANING
6.1 MAIN POINTS OF OPERATION
1. Add 1 cup of hot water and a drop of liquid dishwashing soap to the blender
jar.
1. Turn on the main power switch located on the back of the blender motor in
the lower right corner.
2. Place the lid tightly onto the jar. Place the blender jar on the blender base,
and with your hand placed on top of the lid; press the pulse button for 5
seconds.
2. Place the blender jar on the base, making sure the jar is secure. Attach the
blender lid. Hold the jar lid down with your hand if the jar is more than half
full.
3. Rinse with clear water until all soap is rinsed from jar and lid.
4. Clean the blender base by simply wiping the base and touchpad with a
damp rag and water.
3. Press the desired touch pad button once. You may press any button on the
lower row to stop the cycle.
4. When cycle is complete, remove the blender jar and serve.
5.2 LONG-TERM SANITATION
6.2 AUTOMATIC CYCLE OPERATION
1. For long-term sanitation, occasionally fill the blender jar half way with hot
water.
2. Add one teaspoon of liquid chlorine bleach.
3. Stir for 10 seconds to mix water and bleach. Let mixture stand in blender jar
for five minutes.
4. Empty water/bleach mixture and rinse the jar thoroughly to ensure that there
is no bleach mixture left in the jar. Turn jar RIGHT SIDE UP on dish rack
until dry.
The Blendtec Total Blender has blending cycles for ice cream, frozen yogurt, ice
crushing, milkshakes, soups, syrups, fondues, sauces, dips, dressings, batters,
whole juice, and smoothies. These cycles have variable speed settings that will
change during the course of the cycle. This allows the blender to draw the con-
tents into the blending vortex, which creates the desired texture. The blender will
run its pre-programmed cycle and automatically shut off. If at any point you want
to stop the blender before it has completed its cycle press any lower row button.
Note: The speed buttons allow you to control the blender to operate up to 10
speed settings. Simply press the speed up button and the motor will begin.
Continue pressing the Speed Up key to increase the speed, or press the Speed
Down key at any time to decrease speed. Once you have reached the desired
speed release the button. Once you press a speed button, the blender will begin
to run at the selected speed, then shut off after 50 seconds. To stop the cycle
before the 50 seconds, press any button on the lower row.
5.3 CLEANING TIPS AND CAUTIONS
• Do not use abrasives or stiff brushes to clean the blender base or jar as this
will dull or scratch the surface. Cosmetic damage is not covered by war-
ranty.
• NEVER submerge the blender motor in water. Avoid submerging blender jars
for more than 5 minutes. Water penetration through the lower jar seals will
reduce the life of the jar. After cleaning, we recommend the blender jar be
stored upright.
• BLENDER JAR IS DISHWASHER SAFE - TOP RACK ONLY! Extreme tem-
peratures damage the lower seal to the jar.
TB-6
TB-7
7.3 BLENDED TEXTURE UNSATISFACTORY
If the blended texture of product is lumpy or uneven, do the following:
SECTION 7
TROUBLESHOOTING
• Ensure the mixture is not cavitating during the cycle. Cavitation is a condi-
tion in which the blender blade spins freely in an air pocket within the drink
mix because the mix is too cold or too solid. This problem can be corrected
by increasing the mix temperature by reducing ice, increasing liquid and/or
ensuring that the frozen ingredients used in the recipe are never colder than
10 degrees Fahrenheit (-12 degrees Celsius).
• Increase cycle time. If the drink is mixing well but has not had enough time
for complete blending, try a longer cycle (usually by using higher button
number to start the blender) or touch and hold the “Pulse” button for required
extra blending time.
7.1 BLENDER MOTOR WILL NOT TURN ON
If the blender motor will not turn on, try the following:
• Make sure the main power switch on the back lower-right corner is turned
ON.
• Check your house circuit breaker switch or fuse, to make sure it is set to the
ON position.
• Unplug the power cord from the wall receptacle, wait 5 seconds, then plug
power cord back in.
• Determine if the Liquid Crystal Display (LCD) is lit. An absence of a lit LCD
indicates a lack of power to the unit.
• TRIED EVERYTHING? If none of the preceding suggestions work, contact
your Blendtec service agent for further assistance.
• Remove the blender jar from the blender motor and check to make sure the
blade turns freely while unattached to the motor. If the blade does not move
freely the problem may be the jar, not the motor. Check the jar by turning the
shaft by hand to see if it rotates easily.
Look at the LCD:
• A reading of “OVERTEMP” indicates that the motor is overheating. The
blender has been disabled until the unit cools to operating temperatures.
Turn off and unplug the unit. Allow it to cool for at least 20 minutes.
• A reading of “OVERLOAD” indicates an overload on the motor. Turn off
and unplug the unit. Plug in the unit and turn the motor on again to clear the
over-load condition. Check the blender jar for blockage. If overload condi-
tion re-occurs, contact your Blendtec service agent.
• BLADE STOPS: If the overload switch stops the blender, remove the blender
jar and carefully check for blockage of the blade. If no blockage is found,
replace jar and use the Pulse button on the touch pad to quickly pulse the
blade through the mixture. Once the blade spins freely a programmed but-
ton may be used.
INSTRUCTIONS THAT APPEAR IN THIS USER
GUIDE ARE NOT MEANT TO COVER EVERY
POSSIBLE CONDITION OR SITUATION THAT
MAY OCCUR. GOOD JUDGMENT MUST BE
USED WHEN OPERATING THIS OR ANY OTHER
MACHINERY.
7.2 NOISE LEVEL CHANGES
If the blender noise level has increased significantly from original levels, deter-
mine whether the sound is coming from the blender motor or jar.
• Blender Motor: Check to see if the excess noise is coming from the blender
base. Remove the jar and press cycle number two or three. Listen to the
motor sound without a jar attached. If it is excessively noisy contact your
Blendtec service center.
• Jar: Check to see if the excess noise is coming from the jar. Place the jar
back on the motor. Run the motor for a few seconds using the Pulse button.
If you have more than one jar, test a different jar to determine whether the
sound changes as different jars are used. If a jar is excessively noisy, or if
the blade assembly seems loose or sounds “gravelly” when turned by hand,
contact your Blendtec service center.
TB-8
TB-9
SECTION 8
UNDER WARRANTY
WARRANTY
1. Contact Blendtec immediately to diagnose the difficulty. Please have blender
serial number ready as well as a description of the problem. Do not attempt to
do your own repairs. Repairs made by persons other than Blendtec authorized
service representatives will void the warranty. Many issues can be resolved
simply and quickly over the phone.
WARRANTY DESCRIPTION (US Domestic and Canada)
Your Blendtec Total Blender motor is warrented for 3 years or 10,000 cycles,
whichever happens first. The jar assembly, including all moving jar parts, is cov-
ered against leaking or breakage for 1 year. The blender jar blade and the motor
base drive socket are covered by a lifetime warranty. Warranties begin from date
of purchase.
2. If the difficulty cannot be resolved over the phone, your unit may require re-
placement. If blender is under warranty Blendtec will repair or replace the unit at
no cost. Cosmetic damage and abuse are not included.
The quality of Blendtec blenders are unsurpassed. You will enjoy years of won-
derful and reliable service from your Blendtec Total Blender.
3. Upon receiving instructions from Blendtec, box up your existing unit and en-
close the following:
Warranties begin from the date of purchase. Cosmetic damage, product abuse,
unreasonable use, damage resulting from an accident, product tampering, servic-
ing performed or attempted by unauthorized service agencies, units that have
modifications, or have been or used for commercial purposes are not included
under this warranty.
Your name:
Address:
Phone number:
The blender serial number:
(located on the bottom of the blender motor base)
Cycle Count (from the LCD indicator):
Your purchase date:
An explanation of the problem:
THIS WARRANTY APPLIES ONLY TO PRODUCTS SOLD BY
BLENDTEC OR ITS AUTHORIZED DEALERS
Place of purchase:
Limited Three Year Warranty
OUT OF WARRANTY
Blendtec warrants THE TOTAL BLENDERTM motor to be free of defect in
material and workmanship for a period of three years. During this period, such
defects will be repaired or the product replaced, at Blendtec’s discretion, without
charge. This warranty does not cover damage caused by misuse, accident, or
negligence. All implied warranties, including but not limited to implied warranties
of fitness and merchantability are limited in duration to a period of three years on
motor and one year on Jar. Any unit submitted for repair must be accompanied
by proof of original purchase and should be shipped prepaid to:
1. Contact Blendtec to diagnose the difficulty. Please have the blender serial
number ready along with a description of the problem. Do not attempt to do your
own repairs. Many issues can be resolved simply and quickly over the phone.
2. If the blender is not under warranty and you wish to have it repaired, box up
the blender motor and ship it to Blendtec and you will be billed for services ren-
dered.
3. When you ship your unit please enclose the following:
Blendtec home
1206 South 1680 West
Orem, UT 84058
(800) 253-6383
Your name:
Address:
Phone number:
(801) 222-0888
The blender serial number:
(located on the bottom of the blender base)
Cycle Count (from the LCD indicator):
FOR QUESTIONS REGARDING THIS WARRANTY
CONTACT CUSTOMER SERVICE AT
Your purchase date:
Place of purchase:
An explanation of the problem:
(800) 253-6383 OR (801) 222-0888.
TB-10
TB-11
1206 South 1680 West
Orem, UT 84058
801-222-0888
blendtechome.com
21-801-03 Blendtec Home Total Blender Manual Rev. 02 June 2006
©2006 K-TEC, Inc., All Rights Reserved
Blendtec is a registered trademark of K-TEC, Inc.
|