Jwin Headphones JB TH210 User Manual

Micro-size Hands-Free  
Bluetooth Headset  
Instruction Manual  
JB-TH210  
Please read this manual carefully before operating and save it  
for future reference.  
 
Micro-size Bluetooth headset  
V10M10_IM_EN_12032007  
USER SAFETY GUIDE  
Important Safety Instructions-Continued  
sources such as radiators, heat registers, stoves, or other  
appliances (including amplifiers) that produce heat.  
7. Power sources – The appliance should be connected to a  
power supply only of the type described in the operating  
instructions or as marked on the appliance.  
8. Cleaning – The appliance should be cleaned with a dry cloth.  
9. Objects and liquids entry – Care should be taken so that  
objects do not fall and liquids are not spilled into the device’s  
openings.  
10.Servicing – The user should not attempt to service the  
appliance beyond that described in the user's operating  
instructions. All other servicing should be referred to qualified  
service professional.  
FCC Notice (USA)  
This device complies with Part 15 of the FCC Rules. Operation is  
subject to the following two conditions: (1) this device may not  
cause harmful interference, and (2) this device must accept any  
interference received, including interference that may cause  
undesired operation. Refer to 47 CFR Sec. 15.19.  
This equipment has been tested and found to comply with the  
limits for a Class B digital device, pursuant to Part 15 of the FCC  
Rules. These limits are designed to provide reasonable  
protection against harmful interference in a residential installation.  
This equipment generates, uses, and can radiate radio  
frequency energy and, if not installed and used in accordance  
with the instructions, may cause harmful interference to radio  
- 2 -  
 
Micro-size Bluetooth headset  
V10M10_IM_EN_12032007  
USER SAFETY GUIDE  
FCC Notice (USA)-Continued  
communications, which can be determined by turning the  
equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different  
from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for  
help.  
NOTE: Changes or modifications not expressly approved by  
the party responsible for compliance could void the user’s  
authority to operate the equipment. Refer to 47 CFR Sec.  
15.21.  
Industry Canada Notice to Canadian Users  
Operation is subject to the following two conditions: (1) this  
device may not cause harmful interference, and (2) this device  
must accept any interference received, including interference  
that may cause undesired operation of the device. Refer to IC  
RSS 210 Sec. 5.11. The term “IC” before the certification or  
registration number only means that the registration was  
performed based on a Declaration of Conformity and that  
Industry Canada technical specifications were met. It does not  
imply that Industry Canada (IC) approved this equipment. Refer  
to Self-Marking 6(f) and RSP 100 Sec. 4.  
- 3 -  
 
Micro-size Bluetooth headset  
V10M10_IM_EN_12032007  
USER SAFETY GUIDE  
Additional Safety Instructions  
When not in use, keep your device in a safe place where it  
will not be bent or crushed.  
Keep this device away from children. Some small and  
detachable parts might be swallowed by children and result in  
harm to them.  
About Electromagnetic Interference (EMI)  
This device is designed and manufactured not to exceed the  
exposure limit for radio frequency energy, which is set by the  
Federal Communications Commission of the U.S government.  
The term “EMI” is short for the electromagnetic interference  
caused by the electromagnetic field generated by electronic  
devices. In fact, most electrical appliances and devices emit  
electric and magnetic fields, and most of modern electronic  
devices are susceptible to the EMI if they are inadequately  
shielded or designed.  
If you use any personal medical device, such as a pacemaker,  
please consult the manufacture of your medical device to  
determine if it is adequately shielded from EMI. Your  
physician might assist you in obtaining this information.  
Please turn off this device if you are instructed to do so,  
especially on an airplane or in a hospital.  
Please keep away from medical instruments in a hospital or  
medical unit while using this device.  
- 4 -  
 
Micro-size Bluetooth headset  
V10M10_IM_EN_12032007  
USER SAFETY GUIDE  
IMPORTANT NOTES ON HEARING  
Your hearing is very important to you and to us. We strongly  
recommend you to follow the guideline below in order to prevent  
possible damage to or loss of hearing.  
Hearing experts caution that listening to loud sounds can  
damage hearing over time. With continuous listening to loud  
sounds, hearing adapts and will give the impression that volume  
has reduced. What seems normal may, in fact, be harmful. To  
guard against this before hearing adapts, set the volume at a low  
level and slowly increase the volume level until sound can be  
heard comfortably and clearly without distortion. Damage to  
hearing is accumulative and is irreversible. Ringing or discomfort  
in the ears indicates that the volume is too loud. Once a  
comfortable listening level has been established, do not increase  
the volume level further.  
CAUTION!  
If you experience a ringing sound in your ear, lower the volume  
or discontinue the use of this product.  
- 5 -  
 
Micro-size Bluetooth headset  
V10M10_IM_EN_12032007  
TABLE OF CONTENTS  
GETTING STARTED  
Introduction. …..………..……………………………………… 8  
What’s Included in the Package…………………………..… 8  
What is Bluetooth wireless technology? ............................. 9  
Location of Controls…………………………………………… 10  
Charging the Headset………………………………………… 10  
Turning on the Headset………………………………………. 11  
Turning off the Headset………………………………………. 11  
Pairing the Headset using Bluetooth Wireless Technology. 12  
OPERATING INSTRUCTIONS  
Making a call…………………………………………………… 14  
Answering a call……………………………………………… 14  
Ending a call…………………………………………………… 15  
Rejecting an Incoming Call…………………………………… 15  
Transferring Calls ………………….………………………… 15  
Adjusting the Volume………………………………………… 15  
TROUBLESHOOTING GUIDE  
Questions and answers about the product………………… 16  
SPECIFICATIONS  
Technical information about the product…………………… 16  
- 6 -  
 
Micro-size Bluetooth headset  
V10M10_IM_EN_12032007  
- 7 -  
 
Micro-size Bluetooth headset  
V10M10_IM_EN_12032007  
GETTING STARTED  
Micro size hands-free Bluetooth headset  
Thank you for purchasing the JB-TH210. This headset has been  
designed wireless mobile phone connection using Bluetooth  
wireless technology. Please keep this manual in a safe place for  
future reference.  
Answer or make calls wirelessly without taking your  
mobile phone out  
Supports volume control  
Compliant with Bluetooth V2.0  
Supports HSP and HFP profiles  
Built-in lithium polymer rechargeable battery  
Standby time up to 160 hours  
Continuous talking time up to 5 hours  
Communication range up to 33ft. (10m)  
Light weight: 0.3 oz (9grams)  
What’s included in the package?  
Bluetooth hands-free headset  
AC power adapter  
One extra ear tip  
Instruction manual  
Warranty card  
- 8 -  
 
Micro-size Bluetooth headset  
V10M10_IM_EN_12032007  
GETTING STARTED  
What is Bluetooth wireless technology?  
Bluetooth wireless technology is a short-range wireless  
communication technology intended to replace the cables  
connecting electronic devices while maintaining the high level of  
security. With Bluetooth wireless technology, two devices can be  
connected at the same time without the need to face each other  
or the concern of interference from other wireless communication  
within its optimum range of 33 feet.  
Through a process called “Pairing,” two or more devices with  
Bluetooth wireless technology can interact with each other  
without interference from other wireless platforms nearby,  
including other Bluetooth wireless communications between  
unrelated devices.  
- 9 -  
 
Micro-size Bluetooth headset  
V10M10_IM_EN_12032007  
GETTING STARTED  
LOCATION OF CONTROLS  
6
1
2
4
2
3
3
7
6
4
5
1. Power/answer button  
2. Volume - button  
3. Volume + button  
4. Ear clip  
5. Microphone  
6. Earpiece/receiver  
7. Power connector  
Charging the Headset  
Fully charge the headset by connecting the  
charger to the power connector on the top of  
the headset. The RED indicator light will go on  
during charging  
TOP  
- 10 -  
 
Micro-size Bluetooth headset  
V10M10_IM_EN_12032007  
GETTING STARTED  
Turning on the Headset  
Press and hold the Power/answer button for approximately  
three to five (3-5) seconds until the indicator light begins flashing.  
Note: The indicator will continuously  
flash when the power is on.  
Turning off the Headset  
Press and hold the Power/answer button until the red indicator  
light flashes two times.  
Note: No light will flash when the power is off.  
Please FULLY CHARGE the headset  
before first use.  
- 11 -  
 
Micro-size Bluetooth headset  
V10M10_IM_EN_12032007  
GETTING STARTED  
Pairing with Bluetooth mobile phones  
1. With the power turned off, press and hold the Power/answer  
button until the Blue and Red lights blink alternatively.  
2. Set both the JB-TH210 and the mobile phone to SEARCH  
mode following the pairing instructions included with the  
phone, placing both units close together. Typically mobile  
phones have a Bluetooth menu from which SEARCH can be  
selected.  
3. The mobile phone with Bluetooth  
wireless technology will identify the  
Headset.  
4. Confirm with “yes,” or  
“ok.”  
5. When asked for a passkey or PIN, enter  
0000 (4 zeros) and press “yes,” or “ok.”  
6. Phone and headset have successfully paired.  
- 12 -  
 
Micro-size Bluetooth headset  
V10M10_IM_EN_12032007  
GETTING STARTED  
Notes on Pairing  
This headset will not be recognized by your mobile phone unless  
it is properly paired. The JB-TH210 cannot pair with mobile  
phones which are not equipped with Bluetooth wireless  
technology. To ensure that correct pairing is accomplished, it is  
important to follow both these instructions and those which  
accompany the corresponding mobile phone.  
The JB-TH210 can store pairing information for up to eight (8)  
Bluetooth devices. All devices are stored in the “Pairing Setting  
List” in the order in which pairing occurred. When paired with  
more than eight (8) devices, the earliest paired device will be  
deleted from the list. While the headset can pair to as many as  
eight (8) devices, it can only operate with one device at a time.  
The default device is the one most recently paired. To connect to  
a different device connection must be initiated by the other  
device rather than the JB-TH210.  
- 13 -  
 
Micro-size Bluetooth headset  
V10M10_IM_EN_12032007  
OPERATING INSTRUCTIONS  
Making a call  
Be certain the headset is properly paired with a mobile phone  
featuring Bluetooth wireless technology before answering a call.  
1. Normal dialing: Press the CALL button and dial the  
telephone number on your mobile phone. When the call  
connects, it will be heard through the headset.  
2. Last number redial: After a call has been made, the number  
can be automatically redialed by pressing and holding the  
Power/answer button for approximately 3 seconds.  
3. Voice dial function: Press the Power/answer button, the  
voice call function will be activated.  
Answering a Call  
1. An incoming phone call will be indicated by a ring. Press the  
Power/answer button once to answer the call.  
2. If the headset is off when there is an incoming call, press the  
Power/answer button to turn on the headset and answer the  
call as usual.  
Notes on Answering a Call  
When there is an incoming call, some phones might not ring  
when paired with JB-TH210, but there will be a beeping  
sound from the headset. Press the Power/answer button to  
answer the phone when you hear this beep.  
Similarly, some phones may not send an incoming call signal  
to the headset. Press the Power/answer button when the  
phone rings.  
- 14 -  
 
Micro-size Bluetooth headset  
V10M10_IM_EN_12032007  
OPERATING INSTRUCTIONS  
Ending a Call  
There are several ways to end a phone call.  
1. Press the Power/answer button on the headset.  
2. Press the End key on the mobile phone.  
3. A call will also end as the person on the other end hangs up.  
Note: Your mobile phone with Bluetooth wireless technology  
must be paired with the JB-TH210 BEFORE these functions are  
attempted.  
Rejecting an Incoming Call  
When there is an incoming call, press and hold the  
Power/answer button for approximately 3 to 5 seconds and  
release to reject the call.  
Transferring a call between JB-TH210 and  
your mobile phone  
While talking on the phone, press and hold the Power/answer  
button for approximately three (3) seconds to transfer the call  
between JB-TH210 and mobile phone.  
Adjusting the Volume  
To adjust the volume, press the Volume Up (S) or Volume  
Down (T) button.  
- 15 -  
 
Micro-size Bluetooth headset  
V10M10_IM_EN_12032007  
TROUBLESHOOTING GUIDE  
1. The headset does not work with my mobile phone.  
Be certain that your mobile phone is equipped with Bluetooth  
wireless technology. This headset will only work with such  
mobile phones. Additionally, your mobile phone must be  
paired with the headset BEFORE all other pairing.  
2. There is interference on the headset with my phone.  
The maximum distance for Bluetooth wireless communication  
is 33 feet (10 meters). When this distance is approached,  
background noise will increase. Also, a poor signal on the  
mobile phone may contribute to degradation the quality of  
sound as well.  
3. There is no sound.  
Ensure that both the mobile phone and the JB-TH220 are  
turned on, set up, and paired correctly. Be certain that the  
volume is turned up on both devices.  
Specifications  
Bluetooth spec. v2.0+EDR compliance  
Headset (HSP) and Hands-free Profile (HFP) supported  
Bluetooth Class ll  
Typically 6 hrs Talk Time  
Typically 170 hrs Stand-by Time  
Rechargeable Lithium Polymer Battery  
- 16 -  
 
Micro-size Bluetooth headset  
V10M10_IM_EN_12032007  
- 17 -  
 
Micro-size Bluetooth headset  
V10M10_IM_EN_12032007  
- 18 -  
 
TEL: 516-626-7188  
FAX: 516-626-7105  
© 2007 jWIN Electronics Corp. All rights reserved. The Bluetooth word mark  
and logos are owned by Bluetooth SIG, Inc. and any use of such marks by  
jWIN Electronics Corp. is under license. No portion of this printed material or  
product enclosed herewith including design, shape and graphics, may be  
reproduced or transmitted in any form without the expressed written consent  
of jWIN Electronics Corp. by any means, electronic or mechanical, including  
photocopying, recording or the use of an information storage and retrieval  
system. Any unauthorized distribution or reproduction of this printed material  
or product, or any portion thereof, will be prosecuted to the fullest possible  
extent of the law. Mobile phone not included in this package  
Printed in China  
 

Insignia Home Theater System NS AV511 User Manual
Intermec Printer PK80 User Manual
Jensen Car Amplifier A400HLX User Manual
JVC Car Stereo System GET0735 001A User Manual
JVC CRT Television AV 14FT14 User Manual
Keurig Coffeemaker SS 300C User Manual
KitchenAid Dishwasher W10300235A User Manual
KitchenAid Microwave Oven COOK SPEED OVEN User Manual
KitchenAid Speaker 8301169 User Manual
Klipsch Speaker System SB 3 User Manual