JLWFF1101
wine cooler fridge freezer
Instruction manual
Environmental Information
Warning
•
•
After installation, please dispose of the packaging with
due regard to safety and the environment.
IF YOU ARE DISCARDING AN OLD APPLIANCE THAT
HAS A LOCK OR CATCH ON THE DOOR,YOU MUST
ENSURE THAT IT IS MADE UNUSABLE TO PREVENT
YOUNG CHILDREN BEINGTRAPPED INSIDE.
When disposing of your appliance use an authorised
disposal site. Remove the plug and ensure that all
locks and catches are removed to prevent young
children being trapped inside.
Positioning
This appliance should only be installed at a location
where the ambient temperature corresponds to the
climate classification indicated on the rating plate, which
is located at the left on the inside of the appliance.
•
The symbol
on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it should be taken to the
appropriate collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent
potential negative consequences for the environment
and human health, which could otherwise be caused
by inappropriate waste handling of this product. For
more detailed information about recycling of this
product, please contact your local council, your
household waste disposal service or the shop where
you purchased the product.
The following table shows which ambient temperature is
correct for each climate classification:
SN +10°C to + 32°C
N
+16°C to + 32°C
ST +18°C to + 38°C
+18°C to + 43°C
T
It should be located in a dry atmosphere, out of direct
sunlight and away from extreme temperature e.g. not
next to a boiler or radiator, or in a very cold room e.g. an
outhouse . If these temperatures are exceeded i.e. colder
or warmer, then the appliance may not operate correctly.
Ecological hints
To save energy and help protect the environment, we
recommend that you follow these hints.
Do not install the appliance close to sources of heat such
as a boiler or radiator.
Important
It must be possible to disconnect the appliance from the
mains power supply; the plugs must therefore be easily
accessible after installation.
Locate the appliance in a well-ventilated room and make
sure that any air openings of the appliance are not
obstructed.
Pack all foods into airtight packages before placing them
into the freezer compartment.
Food, which is to be frozen (when cool), should be placed
in the fridge compartment before being transferred to
the freezer.
Try to avoid keeping the door open for long periods or
opening the door too frequently as warm air will enter
the cabinet and cause the compressor to switch on
unnecessarily often.
Ensure there are no obstructions preventing the door
from closing properly.
3
Contents
For the user
Important safety information
2
5
6
6
7
Alarm reset button
16
16
Switching the appliance off
Description of the appliance
Installation
Using the freezer
Before use
17
17
17
17
17
17
17
Technical specifications
Electrical connection
Freezing fresh food
Frozen food storage
Thawing
The control panel refrigerator
When the fridge is first installed
Switching off
8
8
How to make ice cubes
Cold accumulators
8
Temperature setting buttons
Using the refrigerator
Before use
8
Hints and tips
18
9
9
Maintanence and cleaning
Internal cleaning
19
19
19
19
19
20
Temperature display
9
When the appliance is not in use
External cleaning
Quick cool
9
Fresh food refrigeration
Normal operating sounds
Movable shelves
9
Changing the light bulb
Defrosting
9
10
10
10
Something not working
21
22
Positioning the door shelves
Air recycling
Repairs - After sales service
Storage time chart (refrigerator) 11
Guide to use the instruction
manual
The control panel wine cooler
When the wine cooler is first installed
Temperature setting buttons
Temperature display
12
12
12
13
13
14
14
14
14
15
15
15
15
16
The following symbols will be found in the text to
guide you throughout the instructions:
Safety instructions
Hints and tips
Switching the appliance off
Using the wine cooler
Wine cooler
Environmental information
Movable shelves
Normal operating sounds
The control panel freezer
Temperature setting buttons
Temperature display
This appliance complies with the following
E.E.C. Directives:
* 73/23 - 90/683 (LowVoltage Directive);
* 93/68 ("General Product Safety Directive");
* 87/308 (Radio Interference Suppression);
Starting up - setting the temperature
Quick freeze
* 89/336 (Electromagnetic Compatibility
Directive) and subsequent modifications.
4
Description of the appliance
1.
2.
3.
4.
5.
6.
7.
Control panel
Interior lights
Bottle shelves
Freezing fresh food compartment
Frozen food storage compartments
Dairy compartment
8.
9.
10.
11.
12.
13.
Bottle shelf
Quick cool system
Glass shelves
Salad/vegetable drawer
Rating plate
Adjustable feet
Moveable storage shelves
5
Installation
It is dangerous to alter the specifications or
attempt to modify this product in any way.
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
Technical specifications
Dimensions
Width
Height
Depth
1090 mm
1855 mm
547 mm
Power supply voltage
Rated current
230-240V/50Hz
1.1 A + 1.1 A
332 l
Gross capacity
Refrigerator
Wine cooler
Freezer
164 l
91 l
Net capacity
Refrigerator
Wine cooler
Freezer
330 l
162 l
78 l
Freezing capacity
10 kg/24 h
1,345 kWh/24h
491 kWh/year
Energy consumption
Energy class, according to EU
standards
A
25 h
Rising time
Noise Lc
38 dB
129 kg
2
Weight
Number of compressors
6
Electrical connection
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
WARNING: A cut off plug inserted into a
13 amp socket is a serious safety (shock)
hazard.
Ensure that the cut off plug is disposed of
safely.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
Should the appliance power supply cables
need to be replaced, this must be carried
out by a Service Force agent (see page 22)
The plugs must still be accessible after the
appliance has been installed.
The manufacturer declines any liability
should this safety easure not be observed.
The appliance should not be connected to
the electrical supply by means of an
extension cable.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the appliance’s
rating plate. (See picture on page 5).
The appliances are supplied with 2 x 13amp independent
plugs.
In the event of having to change the fuse in the plug
supplied, a 13amp ASTA approved BS 1363/A fuse must be
used.
Should the plug need to be replaced for any reason,
proceed as described below.The wires in the mains lead
are coloured in accordance with the following code:
Green andYellow
Blue
- Earth
- Neutral
- Live
Brown
If you fit your own plug, the colours of the wires in the
mains lead of your appliance may not correspond with
the markings identifying the terminals in your plug.
GREEN & YELLOW
13 AMP. FUSE
BROWN
BLUE
CORD CLAMP
D207
Proceed as follows:
1. Connect the Green and Yellow (earth) wire to the
terminal in the plug which is marked with the letter "E"or
the earth symbol
or coloured green and yellow.
2. Connect the Blue (neutral) wire to the terminal in the plug
which is marked with the letter "N" or coloured black.
3. Connect the Brown (live) wire to the terminal in the
plug which is marked with the letter "L" or coloured red.
4. Upon completion there must be no cut, or stray
strands of wire present and the cord clamp must be
secure over the outer sheath.
7
The control panel refrigerator
Quick
cool
On/Off
˚C
Push button
A. Mains indicator light (green)
E. Temperature setting button (-) (for colder
temperatures)
B. Fridge compartment button ON/OFF
F . Quick cool function "on" indicator light (yellow)
G. Quick cool button
C. Temperature setting button (+) (for warmer
temperatures)
D. Temperature display
When the fridge is first
installed
Switching off
The appliance is switched off by holding in button (B)
for more than 1 second. After this, a countdown on
the temperature display from -3 -2 -1 will be shown.
Warning
When the appliance is switched off, the display (D)
also goes off.
Allow the appliance to stand for 2 hours after
installation.
Insert the plugs into the wall socket.
If the display is OFF press the ON/OFF button.
The green mains indicator light illuminates.
The appliance starts.
Temperature setting buttons
The temperature is adjusted using the “C“ (+) and
“E“ (-) buttons.These buttons are connected to the
temperature display.
Press either the “C“ (+) or “E“ (-) button. The
temperature display switches over and the DESIRED
temperature currently set flashes on the
temperature display.
Set the required temperature by pressing the “C“ (+)
or “E“ (-) buttons (see section "Temperature setting
buttons"). The temperature display will immediately
show the changed setting. Each time a button is
pressed the temperature is adjusted by 1 °C.
The temperature display is switched over from the
display of the ACTUAL temperature (Temperature
display is illuminated) to the display of the DESIRED
temperature (Temperature display flashes) by
pressing one of the two buttons,“C“ (+) or “E“ (-).
Each time one of the two buttons is pressed again
the DESIRED temperature is adjusted by 1 °C.The
DESIRED temperature must be reached within 24
hours.
From a food safety point of view +5 °C should be
considered sufficiently cold for storing food in the
fridge.
Once the required temperature has been set, after a
short period (approx. 5 sec.) the temperature
display will change and again indicate the current
If neither button is pressed, the temperature display
automatically switches back after a short period
(approx. 5 sec.) to the display of the ACTUAL
temperature.
DESIRED temperature means:
The temperature that has been selected for inside
the fridge.The DESIRED temperature is indicated by
flashing numbers.
ACTUAL temperature inside the fridge. The display
will change from flashing to continuous illumination.
Information! When the setting is changed, the
compressor does not start immediately if automatic
defrosting is currently taking place. As the storage
temperature within the fridge is reached quickly you
can store food immediately after switching on.
ACTUAL temperature means:
The temperature display indicates the current
temperature inside the fridge. The ACTUAL
temperature is indicated with illuminated numbers.
8
Using the refrigerator
Fresh food refrigeration
Before use
Remove all securing tapes.Wash inside the appliance
with lukewarm water and bicarbonate of soda (5 ml
to 0.5 litre of water).
To obtain the best performance, do not store warm
food or evaporating liquids in the refrigerator; do
cover or wrap the food, particularly if it has a strong
flavour.
Do not use soap or detergent as the smell
may linger. Dry thoroughly.
Do not cover the shelves with any protective
material, such as paper, cardboard or plastic, which
may obstruct the air circulation through them.
Temperature display
The temperature display can indicate several pieces
of information.
To help you use your refrigerator correctly, here are
some more useful hints:
Raw meat (beef, pork, lamb & poultry): wrap in
polythene bags and place on top of the salad drawer.
During normal operation, the temperature currently
present in the fridge (ACTUAL temperature) is
displayed.
Meat can only be stored safely in this way for
one or two days at the most.
When the temperature is being adjusted a flashing
display indicates the fridge temperature currently
set (DESIRED temperature).
Fruit & vegetables: these should be thoroughly
cleaned and placed in the bottom salad drawer.
Butter & cheese: these should be placed in special
airtight containers or wrapped in aluminium foil or
polythene bags to exclude as much air as possible.
Quick cool
The Quick cool function is suitable for quickly
cooling large quantities of fresh food in the
refrigerator.
Milk bottles: these should have a cap and should
be stored in the bottle rack on the door.
The Quick cool function is switched on by pressing
the Quick cool button "G".The yellow light
Normal operating sounds
• You may hear faint gurgling or bubbling sounds
when the refrigerant is pumped through the coils
or tubing at the rear, to the cooling
plate/evaporator or to the fixed freezer shelves.
illuminates. The Quick cool function is ended
automatically after a period of 6 hours.
The Quick cool function can be ended manually at
any time by pressing the Quick cool button again.
• When the compressor is on, the refrigerant is
being pumped round, and you will hear a whirring
sound or pulsating noise from the compressor.
The yellow light goes out.
9
Movable shelves
The walls of the refrigerator have runners so that
the shelves can be positioned as desired.
D338
Positioning the door shelves
To accomodate the storage of larger items, the door
shelves can be adjusted in height.
To adjust the shelves proceed as follows:
Gradually pull the shelf in the direction of the
arrows until it comes off, then reposition as
required.
Air recycling
The refrigerator compartment is equipped with a
special D.A.C.(Dynamic Air Cooling) fan which can
be turned on with the switch (fig.1).When the green
light is on, the fan system is working.
Fig. 1
SWITCH
It is recommended that the fan (D.A.C.) be used
when the ambient room temperature exceeds
25°C.
This feature enables the rapid cooling of foods and a
more uniform temperature in the compartment.
10
Storage time chart (refrigerator)
Time and method of storage of fresh foods in the refrigerator
Foods
Storage time in days
Method of packaging
cling film, airtight
dish covered
dish covered
1
2
X
X
X
3
x
X
X
4
x
x
x
5
6
7
Raw meat
Cooked meat
Roasted meat
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
x
x
x
x
Raw minced meat
Cold cuts,Vienna sausage
Fresh fish
dish covered
X
x
x
x
x
cling film, cellophane, grease-proof paper
cling film, airtight
dish covered
dish covered
dish covered
cling film, airtight
dish covered
cling film, airtight
dish covered
original packaging
original packaging
original packaging
plastic box
Cooked fish
Fried fish
X
X
x
x
x
x
x
x
x
Tinned fish, open
Fresh chicken
Fried chicken
Fresh duck, goose
Roasted duck, goose
Butter unopened
Butter opened
Milk
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
x
X
X
X
X
X
x
x
x
x
X
X
X
x
x
X
X
X
X
X
x
X
x
X
x
x
x
x
x
X
X
x
x
x
x
x
X
X
X
X
x
Cream
Sour cream
Cheese (hard)
Cheese (soft)
Curds
x
X
x
x
X
x
x
plastic box
aluminium foil
cling film
X
X
x
x
x
x
cling film
Egg
X
X
Spinach, sorrel
Green peas, green beans
Mushroom
cling film
cling film
cling film
cling film
cling film
cling film
cling film
X
x
X
x
x
x
X
x
x
Carrot, roots
Bell-pepper
Tomato
X
X
x
X
X
X
X
X
x
X
Cabbage
X
X
X
X
X
x
x
Soft fruits (strawberries,
raspberries, etc.)
Other fruits
Tinned fruits opened
Cakes filled with cream
X
X
X
X
X
X
X
X
X
X
X
x
x
X
x
x
x
x
x
cling film
cling film
dish covered
dish covered
x
Notation:
X usual storage time
x possible storage time (concerns to really fresh product only)
11
The control panel wine cooler
Quick
freeze
On/Off
On/Off
Alarm off
Freezer
Cooler ˚C
˚C
˚C
Cooler
/
˚C
Freezer
Push button
A. Mains indicator light (green)
B. Wine cooler button On/Off
C. Temperature setting button (+) (for warmer
temperatures)
D. Temperature display
E. Temperature setting button (-) (for colder
temperatures)
defrosting is currently taking place. As the storage
temperature within the Wine cooler is reached
quickly you can store beverage immediately after
switching on.
When the wine cooler is first
installed
Warning
Important: If the wine cooler is switched off,
the door must be closed to ensure that the
freezer is working properly.
Allow the appliance to stand for 2 hours after
installation.
When switched off, the electronic control of
the appliance functions automatically and
periodically circulating the air to prevent
unpleasant smells and humidity within the
compartment.
Insert the plug into the wall socket.
Press On/Off, button B can function the Wine
cooler separately with the appliance in function.
The green mains indicator light illuminates.
Press either the “C“ (+) or “E“ (-) button. The
temperature display switches over and the DESIRED
temperature currently set flashes on the
temperature display.
Temperature setting buttons
The temperature is adjusted using the “C“ (+) and
“E“ (-) buttons.These buttons are connected to the
temperature display.
Set the required temperature by pressing the “C“
(+) or “E“ (-) buttons (see section "Temperature
setting buttons"). The temperature display will
immediately show the changed setting. Each time the
button is pressed the temperature is adjusted by 1
°C.
The temperature display is switched over from the
display of the ACTUAL temperature (Temperature
display is illuminated) to the display of the DESIRED
temperature (Temperature display flashes) by
pressing one of the two buttons,“C“ (+) or “E“ (-).
Once the required temperature has been set, after a
short period (approx. 5 sec.) the temperature
display will change and again indicate the current
ACTUAL temperature inside theWine Cooler.
Each time one of the two buttons is pressed again
the DESIRED temperature is adjusted by 1 °C. The
DESIRED temperature will be reached within 24
The display will change from flashing to continuous
illumination.
Information! When the setting is changed, the
compressor does not start immediately if automatic
12
hours.
If neither button is pressed, the temperature display
automatically switches back after a short period
(approx. 5 sec.) to the display of the ACTUAL
temperature.
DESIRED temperature means:
The temperature that has been selected for inside
the wine cooler. The DESIRED temperature is
indicated by flashing numbers.
ACTUAL temperature means:
The temperature display indicates the current
temperature inside the wine cooler. The ACTUAL
temperature is indicated with illuminated numbers.
Temperature display
The temperature display can indicate several pieces
of information.
During normal operation, the temperature currently
present in the wine cooler. (ACTUAL temperature)
is displayed.
When the temperature is being adjusted a flashing
display indicates the wine cooler temperature
currently set (DESIRED temperature).
Switching the appliance off
The wine cooler can be switched off independently
of the freezer compartment. By switching off the
freezer compartment you also switch off the wine
cooler.To switch off the wine cooler, hold down the
On/Off button (B) for the wine cooler for a count
of 5 Sec.To switch off the appliance hold down the
On/Off button (G) for approx.5 seconds. This will
result in acount down from "3" to "1" taking place in
the temperature display. On reaching "1" the
appliance will switch off. The temperature display
will go off.
13
Using the wine cooler
Wine cooler
Normal operating sounds
To obtain the best performance the temperature
can be adjusted between +6 and + 16°C.
• You may hear faint gurgling or bubbling sounds
when the refrigerant is pumped through the coils
or tubing at the rear, to the cooling
plate/evaporator or to the fixed freezer shelves.
This compartment is ideal for storing and refining
red or white wines for long periods.
• When the compressor is on, the refrigerant is
being pumped round, and you will hear a whirring
sound or pulsating noise from the compressor.
Lay the bottles down in such a way that the
corks do not dry.
Keep the wine in the dark. The door is anti-UV
darkened double glazed glass to protect the wine
from the light in case the appliance is located in a
well-lit place.
Handle the bottles with care, to avoid agitating
the wine.
Follow the recommendations and advice received
at the time of purchase or given in the technical
documentation regarding the quality, duration and
optimum storage temperature for the wine.
Air circulation
Do not cover the shelves with any protective
material, such as paper, cardboard or plastic, which
may obstruct the air circulation through them.
Do not place the bottles at directly against the back
wall of the compartment which will obstruct the air
circulation through them.
Movable shelves
The shelves can be inclined between the two guides,
making sure that the smallest pins are properly
inserted in the upper guide seat and the front part
of the shelf is resting on the front guide.
Adjust the wooden shelves as follows:
The short shelf can be placed on the two short
guides at the top.
The long shelf can be placed on the three long
middle guides and inclined between the last short
guide at the bottom and the shelf support structure.
The shelf support structure must be placed in the
bottom of the compartment.
Important: Only the long shelves can be inserted
in the shelf support structure.
14
The control panel freezer
Quick
freeze
On/Off
On/Off
Alarm off
Freezer
Cooler ˚C
˚C
˚C
Cooler
/
˚C
Freezer
F. Mains indicator light (green)
K. Quick freeze function "on" indicator (yellow)
L. Quick freeze button
G. Button On/Off for the appliance
H. Temperature setting button (for warmer
temperatures)
M. Alarm off reset light
N. Alarm off reset button
I. Temperature display
J. Temperature setting button (for colder
temperatures)
Temperature setting buttons
Temperature display
The temperature is adjusted using the “H“ and “J“
buttons. These buttons are connected to the
temperature display.
The temperature display can indicate several pieces
of information.
During normal operation, the temperature currently
present in the freezer (ACTUAL temperature) is
displayed.
The temperature display is switched over from the
display of the ACTUAL temperature (Temperature
display is illuminated) to the display of the DESIRED
temperature (Temperature display flashes) by
pressing one of the two buttons,“H” or “J“.
When the temperature is being adjusted a flashing
display indicates the freezer temperature currently
set (DESIRED temperature).
Each time one of the two buttons is pressed again
the DESIRED temperature is adjusted by 1 °C.The
DESIRED temperature must be reached within 24
hours.
Starting up - setting the temperature
Plug the mains plug into the mains socket.
Press ON/OFF button (G) for the functioning of the
whole appliance. The green mains pilot indicator
illuminates. The alarm light flashes until the
temperature is reached.The buzzer sounds.
If neither button is pressed, the temperature display
automatically switches back after a short period
(approx. 5 sec.) to the display of the ACTUAL
temperature.
Pressing button “N” stops the buzzer.
DESIRED temperature means:
Press either the H“ or “J” button.The temperature
display switches over and the DESIRED temperature
currently set flashes on the temperature display.
The temperature that has been selected for inside
the freezer. The DESIRED temperature is indicated
by flashing numbers.
Set the required temperature by pressing the “H“ or
“J“ buttons (see section "Temperature setting
buttons"). The temperature display will immediately
show the changed setting. Each time the button is
pressed the temperature is adjusted by 1 °C.
ACTUAL temperature means:
The temperature display indicates the current
temperature inside the freezer.The ACTUAL
temperature is indicated with illuminated numbers.
From a food safety point of view -18 °C should be
considered sufficiently cold for storing food in the
freezer.
The alarm light goes off, when the set temperature
is reached.
15
Note:
Quick freeze
The appliance cannot be switched on or off if
unplugged, or if there is no power being supplied to
it. Following connection to the mains power supply,
the appliance returns to the same operating state as
before the interruption of main power.
The Quick freeze function accelerates the freezing
of fresh food and, at the same time, protects
foodstuffs already stored from undesirable warming.
The Quick freeze function is switched on by
pressing the Quick freeze button. The yellow light
illuminates.
If the appliance is not going to be used for an
extended period:
If the Quick freeze function is not ended manually,
the appliance will switch off the Quick freeze
function after 52 hours.The yellow light goes out.
Switch off the appliance, holding down the On/Off
button (G) until the display goes off (see above).
Remove the main plug .
The Quick freeze function can be ended manually at
any time by pressing the Quick freeze button again.
Finally, leave the doors open so as to avoid a build
up of odours.
The yellow light goes out.
Alarm reset button
In the event of an abnormal temperature rise inside
the freezer (e.g. power cut) warning light (M) will
start to flash and a buzzer will sound.
After the temperature has returned to normal, the
warning light (M) will continue to flash, although the
buzzer has stopped.
When the alarm button is pushed, the warmest
temperature reached in the compartment flashes on
the indicator.
Switching the appliance off
By switching off the freezer compartment
you also switch off theWine Cooler.
To switch off the appliance hold down the On/Off
button (G) for approx. 5 seconds.This will result in a
count down from "3" to "1" taking place in the
temperature display. On reaching "1" the appliance
will switch off.The temperature display will go off.
16
Using the freezer
Before use
Thawing
Frozen food, prior to being used, can be thawed in
the fridge or at room temperature depending on the
time available. Small food items may even be cooked
from frozen; in this case cooking will take longer.
Remove all securing tapes.Wash inside the appliance
with lukewarm water and bicarbonate of soda (5 ml
to 0.5 litre of water).
Do not use soap or detergent as the smell
may linger. Dry thoroughly.
Any frozen food which is allowed to thaw
accidentally should either be eaten as soon as
possible or thrown away. Alternatively, if the food is
uncooked and has not been completely defrosted it
can be cooked and then refrozen.
Freezing fresh food
The 4-star compartment is suitable for the long
term storage of commercially frozen food and for
freezing fresh food.
Meat, fish and fruit should be thawed in the
refrigerator compartment and small pieces of meat
can even be cooked while still frozen, but you must
ensure that it is thoroughly cooked through.
To freeze fresh foods it is not necessary to move
the thermostat knob from the normal setting. Push
the quick freeze switch at least 3 hours before
loading food.
Vegetables should be directly immersed in boiling
water; ready-cooked dishes can be placed directly in
the oven in their aluminium wrapping.
In any 24 hours you can freeze up to 10 kg.of fresh food.
Place the food to be frozen in drawer 4 as indicated
in the diagram on page 5, as this is the coldest part.
A microwave oven is particularly suitable for
thawing any type of frozen or deep-frozen food:
follow the oven instructions, particularly regarding
the placement of aluminium wrapping or containers
in the oven.
To guarantee a good operation of the appliance during
normal use, the drawers should not be removed.
Frozen food storage
Defrosted cooked food must never be
refrozen.
When first starting-up or after a period out of use,
before putting the the frozen food products in the
compartment let the appliance run for at least two
hours on the coldest setting, then turn the
thermostat knob to the normal operating position.
How to make ice cubes
The appliance is provided with a tray for making ice
cubes.
Do not exceed the storage period indicated by the
manufacturer.
Fill the tray(s) 3/4 full to give the ice space to
expand and place them in the freezer compartment.
Finally, do not open the door frequently or leave it
open longer than is absolutely necessary.
To release the ice cubes simply give the tray a slight
twist.
Do not use sharp or metallic instruments to remove
the trays from the freezer.
Warning
Do not put carbonated liquids, (fizzy drinks etc.), in
the freezer compartment.
Cold accumulators
Two cold accumulators are supplied in the freezer;
these increase the length of time the food will keep
in the event of a power failure or breakdown.
Ice lollies, if consumed immediately after removal from
the freezer, can cause low temperature skin burns.
Do not remove items from the freezer if your hands
are damp/wet, as this could cause skin abrasions or
“frost/freezer burns”.
They must be placed in the top drawer.
Important
In the event of a power cut the food in the freezer
will not be affected if the power cut is short and if
the freezer is full. Do not open the door. Should the
food begin to thaw, it must be consumed quickly and
must not be re-frozen.
17
Hints and tips
Food storage
In the event of a power failure
• To obtain the best results from your appliance,
neither hot foods nor liquids which may
evaporate, should be placed in the larder
compartment.
If there is a power failure during the storage of
frozen foods, keep the door closed. If the
temperature within your freezer should rise do not
refreeze the food without checking it’s condition.
The following guidelines should assist you.
• Keep the time between buying chilled food and
placing it in your fridge as short as possible.
Ice Cream:
Once thawed should be discarded.
Fruit andVegetables:
If soft should be cooked and used up.
Bread and Cakes:
Can be refrozen without danger.
Shellfish:
• Do not push food together too much, try to
allow air to circulate around each item.
• Do not store food uncovered.
• Remove suspect food from your refrigerator and
clean, refer to ‘Maintenance and Cleaning’.
• Ensure that food placed in the freezer is dated
and labelled and used in date order to ensure
that food is consumed at its best.
Should be refrigerated and used up quickly.
Cooked Dishes:
i.e. casseroles, should be refrigerated and used up.
Large Pieces of Meat:
Can be re-frozen providing there are ice crystals
remaining within them.
Small Joints:
Should be cooked and then re-frozen as cooked
dishes.
• Avoid buying frozen food if you cannot store it
straight away.The use of an insulated container is
advisable.When you arrive home place the
frozen food in the freezer immediately.
• The symbols on the drawers show different
types of frozen goods.The numbers indicate
storage times in months for the appropriate
types of frozen goods.Whether the upper or
lower value of the indicated storage time is valid
depends on the quality of the foods and pre-
reating before freezing.
Chicken:
Should be cooked and re-frozen as a fresh dish.
Energy saving advice
• Do not install the cabinet close to sources of
heat, i.e. boiler or radiator.
• Locate the appliance in a cool well ventilated
room and make sure that the air openings of the
cabinet are not obstructed.
• Avoid unnecessary frosting in the cabinet by
packing all foodstuffs into airtight packages
before placing them in the freezer.
• Always leave warm food to cool down to room
temperature before placing in the freezer.
• Food which is to be frozen (when cool) should
be placed in the fridge before being transferred
to the freezer.
• Try to avoid keeping the door open for long
periods, or opening the door too frequently as
warm air will enter the cabinet, and cause the
compressor to switch on unnecessarily often.
• Ensure there are no obstructions preventing the
door from closing properly.
18
Maintenance and cleaning
Before any maintenance or cleaning work is carried
out, DISCONNECT the appliance from the
ELECTRICITY supply.
Internal cleaning
Clean the inside and accessories with warm water
and bicarbonate of soda (5ml to 0.5 litre of water).
Rinse and dry thoroughly.
N E V E R U S E D E T E R G E N T S ,
Press on the rear hook and at the same time slide the
cover in the direction indicated by the arrow.
ABRASIVE POWDERS, HIGHLY
PERFUMED CLEANING PRODUCTS
OR WAX POLISHES, TO CLEAN THE
INTERIOR AS THESE WILL DAMAGE
THE SURFACE AND LEAVE A
STRONG ODOUR.
Unscrew the bulb and replace it with one of the same
power (the maximum power is shown on the light
diffuser) available from your nearest Service Force
Centre.
Replace the light cover by sliding it into its original
position.
When the appliance is not in use
When the appliance is not in use for long periods,
disconnect from the electricity supply, empty all
foods and clean the appliance, leaving the doors ajar
to prevent unpleasant smells.
Wine cooler
Should the interior light fail to work, first switch off
the appliance and disconnect from the electricity
supply, then replace the bulb as follows;
External cleaning
Once or twice a year dust the condenser (black
grill) and the compressor at the back of the
appliance, with a brush or vacuum cleaner, see
figure, as an accumulation of dust will affect the
performance of the appliance and cause excessive
electricity consumption.
press on the rear hook and at the same time slide the
cover in the direction indicated by the arrow.
Unscrew the bulb and replace it with one of the same
power (the maximum power is shown on the light
diffuser) available from your nearest Service Force
Centre.
Replace the light cover by sliding it into its original
position.
PR259
Changing the light bulb
Refrigerator
Should the interior light fail to work, first switch off
the appliance and disconnect from the electricity
supply, then replace the bulb as follows;
19
Maintenance and cleaning
Defrosting
Freezer
Your appliance is frost free, which means there is no
need to manually defrost your appliance as this will
be carried out automatically.
Refrigerator
The refrigerator automatically defrosts every time
the compressor stops.The water is discharged, via
the pipe, into a tray located at the back of the
appliance above the compressor, where it
evaporates.
D037
Important
To avoid defrost water overflowing into the fridge,
periodically clean the water discharge hole in the
centre of the V shaped drip collector at the back of
the refrigerator compartment behind the fruit and
vegetable drawer. Use the defrost cleaner provided
which you will find already inserted into the
discharge hole.
Remember to wash the defrost cleaner in hot soapy
water at regular intervals. Dry throughly before
replacing.
20
Something not working
Certain problems are due to a lack of simple maintenance or oversights, which can be solved easily without
calling out an engineer. Please carry out the following checks before contacting the extended warranty
administrators see Repairs - After Sales Service.
IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use
or installation, a charge will be made even if the appliance is under guarantee.
Symptom
Cause
Solution
It is too warm in the
refrigerator.
Thermostatic control can be set incorrectly.
If products are not cold enough or placed
incorrectly.
Set the thermostat knob to higher position.
Place the products to the appropriate place.
The door does not close tightly or it is not
shut properly.
Check if the door closes well and the
gasket is undamaged and clean.
Thermostatic control can be set incorrectly.
The door does not close tightly or it is not
shut properly.
It is too warm in the
freezer.
Set the thermostat knob to higher position.
Check if the door closes well and the
gasket is undamaged and clean.
Products in big quantity to be frozen were put
in.
Wait some hours and then check the
temperature again.
Products to be frozen are placed too closely to
each other.
Place the products in a way so that cold air
could circulate among them.
It is normal. During automatic defrosting frost
melts on the back plate.
The outlet of the chamber can be clogged up.
Products placed in can prevent water from
flowing into the collector.
The melting water outlet flows not into the
evaporative tray above the compressor.
Water flows at the back
plate of the refrigerator.
Water flows into the
chamber.
Water flows onto the
floor.
Clean the outlet.
Replace the products so that they can not
touch the back plate directly.
Put the melting water outlet to the
evaporative tray.
Wrap the products better.
Check if the doors close well and the
gaskets are undamaged and clean.
Products are not wrapped properly.
Doors are not shut properly or do not close
tightly.
There are too much frost
and ice.
Set the thermostat knob to a position that
gives higher temperature.
The thermostatic control can be set
incorrectly.
The compressor operates
continually.
Set the thermostat knob to a position that
gives higher temperature.
The thermostatic control is set incorrectly.
Check if the doors close well and the
gaskets are undamaged and clean.
Wait some hours and then check the
temperature again.
Put food at max. room temperature.
Try to reduce the temperature in the room
where the appliance stands.
Doors are not shut properly or do not close
tightly.
Products in big quantity to be frozen were put
in.
Too warm food was put in.
The appliance is in too warm place.
Connect the mains plug properly.
The appliance does not
work at all. Neither
cooling, nor lighting works.
Plug is not connected to the mains socket
properly.
The fuse burnt out.
Change the fuse.
The thermostatic control is not on.
Start the appliance according to
instructions in chapter 'Putting it into use'.
Call an electrician.
There is no voltage in the mains socket. (Try to
connect another appliance into it.)
The appliance is not supported properly.
Check if the appliance stands stable (all the
four feet should be on the floor).
The appliance is noisy.
In as much as the advice does not lead to result, call the nearest brand-mark service.
21
Repairs - after sales service
In the unlikely event of your appliance requiring
service, or if you wish to purchase spare parts,
please contact our extended warranty
administrators by telephoning:
Spare parts
Always insist on genuine spare parts.
An authorised service engineer should service this
product, and only genuine spare parts should be
used.
0870 010 7887
They will give you details for your local Service
Force Centre.
Under no circumstances should you attempt to
repair the machine yourself. Repairs carried out by
inexperienced persons may cause injury or serious
malfunctioning. Contact your local Service Force
Centre.
Before calling out an engineer, please ensure you
have read the details under the heading “Something
NotWorking”.
When you contact your local Service Force Centre
you will need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of fault
4. The purchase date found on your receipt.
5. The model and serial number of the appliance
(found on the rating plate - see picture on page 5)
So that you always have these numbers at hand, we
recommend you to make a note of them here:
Mod. :......................................................................................
PNC :......................................................................................
S.N. :.......................................................................................
Your Wine Cooler Fridge Freezer is covered
by a 3 year parts and labour guarantee (see
separate details given at point of sale). Please
retain your purchase receipt safely for the
service engineer to verify the purchase
details.
22
|