JLFFW1811
JLSS1814
JLFFW2012
JLSS2015
JLFFW2013
Fridge-Freezer
Instruction manual
• The appliance is intended for keeping
foodstuff and/or beverages in a normal
household as explained in this instruction
booklet.
• Do not use a mechanical device or any
artificial means to speed up the thawing
process.
• Do not use other electrical appliances (such
as ice cream makers) inside of refrigerating
appliances, unless they are approved for
this purpose by the manufacturer.
3. Make sure that you can come to the
mains plug of the appliance.
4. Do not pull the mains cable.
5. If the power plug socket is loose, do not
insert the power plug. There is a risk of
electric shock or fire.
6. You must not operate the appliance
without the lamp cover of interior
lighting.
• This appliance is heavy. Care should be
taken when moving it.
• Do not remove nor touch items from the
freezer compartment if your hands are
damp/wet, as this could cause skin
abrasions or frost/freezer burns.
• Do not damage the refrigerant circuit.
• The refrigerant isobutane (R600a) is
contained within the refrigerant circuit of
the appliance, a natural gas with a high level
of environmental compatibility, which is
nevertheless flammable.
• Avoid prolonged exposure of the appliance
to direct sunlight.
During transportation and installation of
the appliance, be certain that none of the
components of the refrigerant circuit
become damaged.
If the refrigerant circuit should become
damaged:
Daily Use
• Do not place hot items such as pans and
baking trays near the plastic components of
the appliance.
• Do not store flammable gas and liquid in the
appliance, because they may explode.
• Do not place food products directly against
the air outlet on the rear wall.1)
• Frozen food must not be re-frozen once it
has been thawed out.
• Store pre-packed frozen food in
accordance with the frozen food
manufacturer's instructions.
– avoid open flames and sources of ignition
– thoroughly ventilate the room in which
the appliance is situated
• It is dangerous to alter the specifications or
modify this product in any way. Any
damage to the cord may cause a short-
circuit, fire and/or electric shock.
Warning! Any electrical component
(power cord, plug, compressor) must
be replaced by a certified service agent
or qualified service personnel.
• Appliance's manufacturers storage
recommendations should be strictly
adhered to. Refer to relevant instructions.
• Do not place carbonated or fizzy drinks in
the freezer compartment as it creates
pressure on the container, which may
cause it to explode, resulting in damage to
the appliance.
1. Power cord must not be lengthened.
2. Make sure that the power plug is not
squashed or damaged by the back of
the appliance. A squashed or damaged
power plug may overheat and cause a
fire.
1) If the appliance is Frost Free
3
• Ice lollies can cause frost burns if consumed • The appliance must not be located close to
straight from the appliance.
radiators or cookers.
• Make sure that the mains plug is accessible
after the installation of the appliance.
Care and cleaning
• Before maintenance, switch off the
appliance and disconnect the mains plug
from the mains socket.
Service
• Any electrical work required to do the
servicing of the appliance should be carried
out by a qualified electrician or competent
person.
• Do not clean the appliance with metal
objects.
• Do not use sharp objects to remove frost
from the appliance. Use a plastic scraper.
• Regularly examine the drain in the
refrigerator for defrosted water. If
necessary, clean the drain. If the drain is
blocked, water will collect in the bottom of
the appliance.
• This product must be serviced by an
authorised Service Centre, and only
genuine spare parts must be used.
Environment Protection
This appliance does not contain gasses
which could damage the ozone layer,
in either its refrigerant circuit or
insulation materials. The appliance
shall not be discarded together with
the urban refuse and rubbish. The
insulation foam contains flammable
gases: the appliance shall be disposed
according to the applicable regulations
to obtain from your local authorities.
Avoid damaging the cooling unit,
especially at the rear near the heat
exchanger. The materials used on this
appliance marked bythe symbol are
recyclable.
Installation
Important! For electrical connection
carefully follow the instructions given in
specific paragraphs.
• Unpack the appliance and check if there are
damages on it. Do not connect the
appliance if it is damaged. Report possible
damages immediately to the place you
bought it. In that case retain packing.
• It is advisable to wait at least four hours
before connecting the appliance to allow
the oil to flow back in the compressor.
• In order to prevent over heating there must
be adequate circulation around the
appliance.
• Please refer to the correct positioning and
location instructions that can be found in
the Installation section of this user guide.
4
Contents
For the user
For the installer
Safety information
2
6
Technical data
20
Product description
Installation
Positioning
Location
Electrical Connection
Permanent connection
Rear spacers
20
20
20
21
22
22
22
22
23
23
Control panel
Display
First switch on
Switching off
Functions Menu
Temperature regulation
Holiday Function "H"
Ambient Temperature Function
Child Lock Function
Shopping Function
Eco Mode Function
Action Freeze Function
Drinks Chill Function
Excessive temperature alarm
7
7
8
8
8
8
8
9
9
9
9
9
10
10
Levelling
Removing the shelf holders
Installation of the carbon air filter
Door reversibility
Repairs - after sales service
Environmental concerns
26
27
First use
Cleaning the interior
11
11
Daily use
11
11
11
11
11
12
12
12
13
Storage of frozen food
Thawing
Carbon Air Filter
Movable shelves
Bottle rack
Vegetable Drawer
Positioning the door shelves
Chiller Zone
Guide to use the
instruction manual
The following symbols will be found in the text
to guide you throughout the instructions:
Removaloffreezingbasketsfromthefreezer 14
Helpful hints and tips
14
Safety instructions
Hints and tips
Care and cleaning
Periodic cleaning
Replacing the carbon air filter
Defrosting
16
16
16
17
Environmental information
What to do if…
17
5
Product description
1
22
14
15
2
3
4
16
17
5
6
18
20
21
7
8
19
9
10
11
12
13
23
24
25
A - Refrigerator
B - Freezer
1 Control panel
13 Adjustable feet
14 Dairy compartment
15 Egg tray
2 Air distribution and light box
3 Glass shelves
4 Bottle rack
16 Door shelf
17 Door gasket
18 Bottle shelf
5 Glass shelf
19 Handles
6 Chiller Zone compartment
7 Salad/vegetable drawer
8 Rating plate
20 Condenser
21 Defrost water outlet tube
22 Spacers
9 Air grid
23 Evaporator tray
24 Compressor
25 Rollers
10 Storing compartment(s)
11 Quick freeze drawer
12 Bottom plinth
6
Control panel
A B
C
D E
A - Appliance button ON/OFF
D - Function button
B - Temperature regulation button
C - Temperature and function indicator
E - Confirmation button
Display
Indicates the compartment is on.
Child Lock function indicator.
Timer function indicator.
Indicates the temperature of the
relevant compartment.
If it flashes the operations corresponds
to the relative compartment.
Shopping function indicator.
Excessive temperature alarm.
Drinks Chill function indicator.
Action Freeze function indicator.
If on the indicated temperature is the
ambient temperature.
Positive or negative temperature
indicator.
Eco mode function indicator.
Temperature indicator.
7
The following functions are indicated:
Select/Switch off/Switch on fridge
compartment
Select/Switch off/Switch on freezer
compartment
First switch on
After plugging the plug into the power outlet,
if the display is not illuminated, press key (A),
appliance on.
As soon as the appliance is turned on, it is in
alarm condition, the temperature flashes and
you will hear a buzzer.
Press key (E) and the buzzer will go off (also
see the section on "excessive temperature
Ambient Temperature
Child Lock function
Shopping function
Eco Mode function
Action Freeze function
Drinks Chill function
alarm" ) the icon
still flashes and on the
indicator will appear the warmest
temperature reached.
Temperature regulation
For a correct storage of the food select the
Eco mode function that guarantee the
following temperatures are set:
+5°C in the fridge
The temperature may be regulated by
pressing the key (D) to select the
compartment and than the key (B) to set the
desired temperature.
-18°C in the freezer
By pressing the key (B) the current
temperature setting flashes on the indicator.
To confirm the choice of the temperature
press the key (E).
• Wait until the inside compartment
temperature reach -18°C, before
introducing the goods in the freezer
compartment.
You will hear the buzzer for few seconds and
the indicator displays the newly selected
temperature for a few seconds, then shows
again the inside compartment temperature.
The newly selected-temperature must be
reached after 24 hours.
After a long period out of use it is not
necessary to set again the temperature
because it remains stored.
• To select a different temperature see
"Temperature regulation".
Important!If the door remains ajar for some
minutes, the internal lighting will turn off
electronically; after this, the lighting function
will be reset by closing and opening the door
itself.
Switching off
Important!During thestabilityperiodbythe
first starting the temperature displayed can
not correspond to the setting temperature.
During this time it is possible that the
temperature displayed is different than the
setting temperature.
The appliance is shut off by pressing button
(A) until a countdown from -3 -2 -1 is
completed.
Functions Menu
By activating the key (D) the functions menu
is operating. Each function could be confirmed
by pressing button (E). If there is no
confirmation after some seconds the display
will go out from the menu and return in
normal condition.
Holiday Function "H"
The holiday function sets the temperature at
+ 15°C.
8
This function allows you to keep the
refrigerator shut and empty during a long
holiday period ( e. g. the summer holidays)
without the formation of a bad smell.
To turn on the holiday function operate as per
modift the selected temperature. The
temperature indicator can modify the
displayed temperature up to + 8 °C, 1 °at a
tim. + 2 °C will be followed by the letter "H
". Press key E to confirm.
It is possible to de-activate the function at any
time by pressing key (D) until the
corresponding icon will flash and then key (E).
Shopping Function
If you need to insert a large amount of warm
food, for example after doing the grocery
shopping, we suggest activating the Shopping
function to chill the products more rapidly and
to avoid warming the other food which is
already in the refrigerator.
Now the refrigerator is in the "holiday
"function in the energy- saving mode.
The Shopping function is activated by pressing
key (D) (several times if necessary) until the
corresponding icon appears . You must
confirm the choice by pressing key (E) within
few seconds. You will hear the buzzer and the
icon remains lighted.
The Shopping function shuts off automatically
after approximately 6 hours. It is possible to
de-activate the function at any time by
pressing key (D) until the corresponding icon
will flash and then key (E).
Important! The fridge compartment must
be empty with holiday function on.
Ambient Temperature
Function
The ambient temperature function is
activated by pressing key (D) (several times if
necessary) until the corresponding icon
appears
. In this condition the displayed
temperature is the ambient temperature.
You must confirm the choice by pressing key
(E) within few seconds. You will hear the
buzzer and the icon remains lighted.
It is possible to de-activate the function at any
time by pressing key (D) until the
Eco Mode Function
The Eco Mode function is activated by
pressing key (D) (several times if necessary)
until the corresponding icon appears
You must confirm the choice by pressing key
(E) within few seconds. You will hear the
buzzer and the icon remains lighted.
corresponding icon will flash and then key (E)
In this condition the chosen temperatures are
automatically set (+ 5°C and - 18°C), in the
best conditions for storing food.
It is possible to de-activate the function at any
time by changing the selected temperature in
one of the compartment.
Child Lock Function
The Child Lock function is activated by
pressing key (D) (several times if necessary)
until the corresponding icon appears
.
You must confirm the choice by pressing key
(E) within few seconds. You will hear the
buzzer and the icon remains lighted. In this
condition any possible operation through the
keys does not cause any change as long as this
function is activated.
Action Freeze Function
The freezer compartment is suitable for long
term storage of commercially frozen and
deep-frozen food, and for freezing fresh food.
9
The maximum quantity of foods to freeze in
24 hours is shown on the rating plate.
To freeze the amount of food indicated on the
rating plate, place the food directly in touch
with the cooling surface (remove the drawer
or basket). In case the food is frozen inside the
drawers or baskets, the maximum quantity is
slightly reduced.
To freeze fresh foods, you will need to
activate the Action Freeze function. Press key
(D) (several times if necessary) until
indicator appears.
You must confirm the choice by pressing key
(E) within few seconds. You will hear the
buzzer and on the display will appear some
animation with lines.
After a pre-cooling period of 24 hours, place
the foods in the freezer.
Place the food to be frozen in the
compartment, as this is the coldest point.
The freezing process takes 24 hours. During
this period do not put other foods in the
freezer.
This function stops automatically after 52
hours.
It is possible to deactivate the function at any
At the end of the selected time there are the
following indications:
• on the indicator
the symbol flashing
•
the icon
flashing
• the icon flashing
• sounding of an acoustic alarm until key (E)
is pressed
At this point bear in mind to remove the
drinks contained in the freezer compartment.
It is possible to deactivate the function at any
time by pressing key (D) until the
corresponding icon will flash and then key (E).
Excessive temperature
alarm
An increase in the temperature in a
compartment (for example due to an power
failure) is indicated by:
• flashing temperature
•
freezer compartment flashing
• flashing of the icon
• sounding of buzzer
When normal conditions are restored:
• the acoustic signal shuts off
• the temperature value continues to flash
When you press key (E) to de-activate the
alarm, the highest temperature reached in the
time by pressing key (D) until
flash and then press key (E).
indicator will
Drinks Chill Function
compartment appears on indicator
some seconds.
for
The Drinks Chill function is to be used as a
safety warning when placing bottles in the
freezer compartment. It is activated by
pressing key (D) (several times if necessary)
Then it returns on the normal operation
showing the temperature of the selected
compartment.
During the alarm phase, the buzzer can be
switched off by pressing key (E).
until the corresponding icon appears
.
You must confirm the choice by pressing key
(E) within few seconds. You will hear the
buzzer and the icon remains lighted.
In this condition it operates a timer with a
default value of 30 min. and it could change
from 1 to 90 min., by pressing key (B) you
select the minutes needed.
10
First use
Important! Do not use detergents or
abrasive powders, as these will damage the
finish.
Cleaning the interior
Before using the appliance for the first time,
wash the interior and all internal accessories
with lukewarm water and some neutral soap
so as to remove the typical smell of a brand-
new product, then dry thoroughly.
Daily use
Storage of frozen food
Carbon Air Filter
When first starting-up or after a period out of Your appliance is equipped with a carbon filter
use, before putting the products in the
behind a flap in the rear wall of the air
compartment let the appliance run at least 2 distributing box.
hours on the higher settings.
The filter purifies the air from unwanted
odours in the fridge compartment meaning
that the storage quality will be further
improved.
Important! In the event of accidental
defrosting, forexample due toa powerfailure,
if the power has been off for longer than the
value shown in the technical characteristics
Important! During the operation, always
chart under "rising time", the defrosted food keep the air ventilation flap closed.
must be consumed quickly or cooked
immediately and then re-frozen (after
cooling).
Thawing
Deep-frozen or frozen food, prior to being
used, can be thawed in the refrigerator
compartment or at room temperature,
depending on the time available for this
operation.
Small pieces may even be cooked still frozen,
directly from the freezer: in this case, cooking
will take longer.
Movable shelves
The walls of the refrigerator are equipped
with a series of runners so that the shelves can
be positioned as desired.
Download from Www.Somanuals.c1om1. All Manuals Search And Download.
There is a separator inside the drawer that can
be placed in different positions to allow for the
subdivision best suited to personal needs.
There is a grille (if foreseen) on the bottom of
the drawer to separate the fruit and
vegetables from any humidity that may form
on the bottom surface.
All parts inside the drawer can be removed
for cleaning purposes
1
2
Bottle rack
Place the bottles (with the opening facing
front) in the pre-positioned shelf.
Important! If the shelf is positioned
horizontally, place only closed bottles.
This bottle holder shelf can be tilted in order
to store previously opened bottles. To obtain
this result, pull the shelf up so it can rotate
upwards and be placed on the next higher
level.
Positioning the door
shelves
To permit storage of food packages of various
sizes, the door shelves can be placed at
different heights.
To make these adjustments proceed as
follows:
gradually pull the shelf in the direction of the
arrows until it comes free, then reposition as
required.
Vegetable Drawer
The drawer is suitable for storing fruit and
vegetables.
12
5
6
Chiller Zone
2
The Chiller Zone compartment is suitable for
storing fresh food like fish, meat, seafood,
because the temperature is lower here than
in the rest of the fridge. It is placed in the lower
part of the refrigerator, directly above of the
vegetable drawer.
3
1. Open the door of the refrigerator as wide
as possible. If you cannot open the door
at an angle of 180° because of a limit stop
or any other objects , remove the bottle
shelf from the door.
If you wish to remove the Chiller Zone
compartment, do these steps:
2. Pull the drawer towards yourself to the
end point.
3. Slightly lift the front part of the drawer.
4. Remove the drawer from its support.
5. Lift the back of the support from its nest.
6. Pull the frame towards yourself.
7. Remove the support frame.
To put the Chiller Zone compartment to its
initial position, do above steps in opposite
sequence.
Download from Www.Somanuals.c1om3. All Manuals Search And Download.
Removal of freezing
baskets from the freezer
The freezing baskets have a limit stop to
prevent their accidental removal or falling out.
At the time of its removal from the freezer,
pull the basket towards yourself and, upon
reaching the end point, remove the basket by
tilting its front upwards.
At the time of putting it back, slightly lift the
front of the basket to insert it into the freezer.
Once you are over the end points, push the
baskets back in their position.
2
1
Helpful hints and tips
• When the compressor is on, the refrigerant
is being pumped around and you will hear
a whirring sound and a pulsating noise from
the compressor. This is correct.
• The thermic dilatation might cause a
sudden cracking noise. This is not a fault
with the appliance and is a completely
normal operating sound.
Normal Operating
Sounds
• You may hear a faint gurgling and a bubbling
sound when the refrigerant is pumped
throughthe coils or tubing. This is notafault
with the appliance and is a completely
normal operating sound.
14
Milk bottles: these should have a cap and
should be stored in the bottle rack on the
door.
Bananas, potatoes, onions and garlic, if not
packed, must not be kept in the refrigerator.
Hints for energy saving
• Do not open the door frequently or leave
it open longer than absolutely necessary.
• If the ambient temperature is high and the
Temperature Regulator is set to low
temperature and the appliance is fully
loaded, the compressor may run
continuously, causing frost or ice on the
evaporator. If this happens, set the
Temperature Regulator towards a warmer
setting to allow automatic defrosting and
will therefore save in electricity
Hints for freezing
To help you make the most of the freezing
process, here are some important hints:
• the maximum quantity of food which can
be frozen in 24 hrs. is shown on the rating
plate;
consumption.
• the freezing process takes 24 hours. No
further food to be frozen should be added
during this period;
• only freeze top quality, fresh and
thoroughly cleaned, foodstuffs;
• prepare food in small portions to enable it
to be rapidly and completely frozen and to
make it possible subsequently to thaw only
the quantity required;
• wrap up the food in aluminium foil or
polythene and make sure that the packages
are airtight;
Hints for fresh food
refrigeration
To obtain the best performance:
• do not store warm food or evaporating
liquids in the refrigerator
• do cover or wrap the food, particularly if it
has a strong flavour
• position food so that air can circulate freely
around it
• do not allow fresh, unfrozen food to touch
food which is already frozen, thus avoiding
a rise in temperature of the latter;
Hints for refrigeration
Useful hints:
• lean foods store better and longer than
fatty ones; salt reduces the storage life of
food;
Meat (all types) : wrap in polythene bags and
place on the glass shelf above the vegetable
drawer.
For safety, store in this way only one or two • it is advisable to show the use by date on
days at the most.
each individual pack to enable you to keep
tab of the storage time.
Cooked foods, cold dishes, etc.: these should
be covered and may be placed on any shelf.
Fruit and vegetables: these should be
thoroughly cleaned and placed in the special
drawer(s) provided.
Butter and cheese: these should be placed in
special airtight containers or wrapped in
aluminium foil or polythene bags to exclude as
much air as possible.
Warning! Lolly ices, if consumed
immediately after removal from the
freezer compartment can cause
freezer burns.
Download from Www.Somanuals.c1om5. All Manuals Search And Download.
• not open the door frequently or leave it
open longer than absolutely necessary.
• Once defrosted, food deteriorates rapidly
and cannot be refrozen.
• Donotexceedthestorage periodindicated
by the food manufacturer.
Hints for storage of
frozen food
To obtain the best performance from this
appliance, you should:
• make sure that the commercially frozen
foodstuffs were adequately stored by the
retailer;
• be sure that frozen foodstuffs are
transferred from the foodstore to the
freezer in the shortest possible time;
Care and cleaning
Clean the condenser (black grill) and the
Caution! Unplug the appliance
before carrying out any maintenance
operation.
compressor at the back of the appliance with
a brush or a vacuum cleaner. This operation
will improve the performance of the appliance
and save electricity consumption.
This appliance contains hydrocarbons
in its cooling unit; maintenance and
recharging must therefore only be
carried out by authorised technicians.
Important! Take care of not to damage the
cooling system.
Many proprietary kitchen surface cleaners
contain chemicals that can attack/damage the
plastics used in this appliance. For this reason
it is recommended that the outer casing of this
appliance is only cleaned with warm water
with a little washing-up liquid added.
After cleaning, reconnect the equipment to
the mains supply.
Periodic cleaning
The equipment has to be cleaned regularly:
• clean the inside and accessories with
lukewarm water and some neutral soap.
• regularly check the door seals and wipe
clean to ensure they are clean and free from
debris.
• rinse and dry thoroughly.
Replacing the carbon air
filter
To get the best performance the carbon air
filter should be changed once every year.
New active air filters can be purchased from
your local dealer.
Important! Do not pull, move or damage
any pipes and/or cables inside the cabinet.
Never use detergents, abrasive powders,
highly perfumed cleaning products or wax
polishes to clean the interior as this will
damage the surface and leave a strong odour.
Refer to "Installation of the carbon air filter"
for the instructions.
16
The absence of frost is due to the continuous
circulation of cold air inside the compartment,
driven by an automatically controlled fan.
Defrosting
Your appliance is frost free. This means that
there is no build up of frost when it is in
operation, neither on the internal walls nor on
the foods.
What to do if…
Caution! Before troubleshooting,
disconnect the power supply.
Only a qualified electrician or
competent person must complete any
repairs to the appliance.
Important! It is normal to hear some
operating noises during use (for example the
compressor, refrigerant circulation).
Problem
Possible cause
Solution
The appliance is noisy.
The appliance is not supported
properly.
Check if the appliance stands stable
(all the four feet should be on the
floor).
The compressor
operates continually.
The Temperature regulator may Set a warmer temperature.
be set incorrectly.
The door is not closed correctly. Refer to "Closing the door".
The door has been opened too
frequently.
Do not keep the door open longer
than necessary.
The product temperature is too Let the product temperature
high.
decrease to room temperature
before storage.
The room temperature is too
high.
Decrease the room temperature.
The Action Freeze function is
switched on.
Refer to "Action Freeze function".
Water flows on the rear During the automatic defrosting This is correct.
plate of the refrigerator. process, frost defrosts on the rear
plate.
Water flows into the
refrigerator.
The water outlet is clogged.
Clean the water outlet.
Products prevent that water flows Make sure that products do not
into the water collector. touch the rear plate.
Download from Www.Somanuals.c1om7. All Manuals Search And Download.
Problem
Possible cause
Solution
Water flows on the
ground.
The melting water outlet does not Attach the melting water outlet to
flow in the evaporative tray above the evaporative tray.
the compressor.
There is too much frost Products are not wrapped
and ice.
correctly..
Please refer to the "Hints for
refrigeration" and "Hints for
freezing" instructions in this guide.
The door is not closed correctly. Refer to "Closing the door".
The Temperature regulator may Set a higher temperature.
be set incorrectly.
The temperature in the The door is not closed correctly. Refer to "Closing the door".
appliance is too high.
The product temperature is too Let the product temperature
high.
decrease to room temperature
before storage.
Many products are stored at the Store less products at the same
same time. time.
The temperature in the There is no cold air circulation in Make sure that there is cold air
refrigeration is too high. the appliance.
circulation in the appliance.
The temperature in the Products are too near to each
Store products so that there is cold
air circulation.
freezer is too high.
other.
The appliance does not The appliance is switched off.
Switch on the appliance.
operate.
The mains plug is not connected Please refer to the installation
to the mains socket correctly.
instructions provided in this user
guide.
The appliance has no power.
To test this connect a different
There is no voltage in the mains electrical appliance to the mains
socket.
socket. Contact a qualified
electrician.
The lamp does not work. The lamp is defective.
Refer to "Replacing the lamp".
If after following these instructions you do not 2. Remove the lamp cover.
resolve the fault with your appliance please
refer to the "Repairs - After Sales Service".
3. Replace the lamp with one of the same
power (the maximum power is shown on
the light bulb cover).
Replacing the lamp
4. Install the lamp cover.
5. Connect the plug to the mains socket.
6. Open the door. Make sure that the light
comes on.
Caution! Disconnect the plug from
the mains socket.
1. Pull outwards the hook of the lamp cover.
18
1
2
Closing the door
1. Clean the door gaskets.
2. If necessary, adjust the door. Refer to
"Installation".
3. If necessary, replace the defective door
gaskets. Contact the Service Force
Center.
Download from Www.Somanuals.c1om9. All Manuals Search And Download.
Technical data
JLFFW1811
JLSS1814
JLFFW2013
JLSS2015
JLFFW2012
Dimension
Height
Width
Depth
1850 mm
595 mm
632 mm
16 h
2010 mm
595 mm
632 mm
16 h
2010 mm
595 mm
632 mm
16 h
Rising Time
The technical information are situated in the
rating plate on the internal left side of the
appliance and in the energy label.
Installation
Read the "Safety Information" carefully
for your safety and correct operation
of the appliance before installing the
appliance.
Location
The appliance should be installed well away
from sources of heat such as radiators,
boilers, direct sunlight etc. Ensure that air can
circulate freely around the back of the cabinet.
To ensure best performance, if the appliance
is positioned below an overhanging wall unit,
the minimum distance between the top of the
cabinet and the wall unit must be at least 100
mm . Ideally, however, the appliance should
not be positioned below overhanging wall
units. Accurate levelling is ensured by one or
more adjustable feet at the base of the
cabinet.
Positioning
Install this appliance at a location where the
ambient temperature corresponds to the
climate class indicated on the rating plate of
the appliance:
Climate Ambient temperature
class
SN
N
+10°C to + 32°C
+16°C to + 32°C
+16°C to + 38°C
+16°C to + 43°C
ST
T
20
Warning! It must be possible to
disconnect the appliance from the
mains power supply; the plug must
therefore be easily accessible after
installation.
Green and Yellow:
Brown:
Earth
Live
1
3
5
Blue:
Neutral
As the colours of the wires in the mains lead
of this appliance may not correspond with the
coloured markings identifying the terminals in
your plug, proceed as follows:
1. Connect the wire coloured green and
yellow to the terminal marked either with
the letter “E“ or by the earth symbol
or coloured green and yellow.
Electrical Connection
Caution! Any electrical work
required to install this appliance should
be carried out by a qualified electrician
or competent person.
Warning! This appliance must be
earthed.
The manufacturer declines any liability
should these safety measures not be
observed.
2. Connect the wire coloured blue to the
terminal either marked with the letter
“N“ or coloured black.
3. Connect the wire coloured brown to the
terminal either marked with the “L“ or
coloured red.
Important! The wires in the mains lead are
coloured in accordance with the following
code:
4. Check that no cut, or stray strands of wire
4
is present and the cord clamp is secure
over the outer sheath.
5. Make sure the electricity supply voltage is
the same as that indicated on the
appliance rating plate.
6. Switch on the appliance.
Download from Www.Somanuals.c2om1. All Manuals Search And Download.
The appliance is supplied with a 13 amp plug
Levelling
When placing the appliance ensure that it
stands level. This can be achieved by two
adjustable feet at the bottom in front.
2
fitted . In the event of having to change the
fuse in the plug supplied, a 13 amp ASTA
approved (BS 1362) fuse must be used.
Warning! A cut off plug inserted into
a 13 amp socket is a serious safety
(shock) hazard. Ensure that it is
disposed of safely.
Permanent connection
In the case of permanent connection it is
necessary that you install a double pole switch
between the appliance and the electricity
supply (mains), with a minimum gap of 3mm
between the switch contacts and of a type
suitable for the required load in compliance
with the current electrical regulations.
The switch must not break the green and
yellow earth cable at any point.
Removing the shelf
holders
Rear spacers
In the bag with the documentation, there are
two spacers which must be fitted as shown in
the figure.
Slacken the screws and insert the spacer
under the screw head, then tighten again the
screws.
Your appliance is equipped with shelf
retainers that make it possible to secure the
shelves during transportation.
To remove them proceed as follows:
1. Move the shelf holders in the direction of
the arrow (A).
2. Raise the shelf from the rear and push it
forward until it is freed (B).
3. Remove the retainers (C).
22
A
B
C
Important! During operation, always keep
the air ventilation flap closed.
The filter should be handled carefully so
fragments do not loosen from the surface.
Installation of the carbon
air filter
Door reversibility
The carbon air filter is an active carbon filter
which absorbs bad odours and permits to
maintain the best flavour and aroma for all
foodstuffs without risk of odour cross
contamination.
On delivery the carbon filter is in a plastic bag
to maintain it’s duration and characteristics.
The filter should be placed behind the flap
before the appliance is turned on.
Warning! Before carrying out any
operations, remove the plug from the
power socket.
Important! To carry out the following
operations, we suggest that this be made with
another person that will keep a firm hold on
the doors of the appliance during the
operations.
1. Open the flap cover (1)
To change the opening direction of the door,
do these steps:
1. Open the door with the appliance in the
upright position. Unscrewthe screws (t1)
and remove the upper door plastic trim
(t2). Close the door.
2. Remove the filter from the plastic bag
3. Insert the filter in the slot found in the back
of the flap cover (2)
4. Close the flap cover
Download from Www.Somanuals.c2om3. All Manuals Search And Download.
t1
t1
d1
t1
t2
t3
d7
6. Unscrew the middle hinge (m2). Remove
the plastic spacer (m1).
2. Remove the little plastic cover from the
door plastic trim and refit on the opposite
side (t3).
3. Remove the panel (t4). If it is necessary
use a screwdriver very carefully. Unscrew
the screw on the other side. Remove the
upper door mount (t5) . Place them in an
empty plastic bag.
m1
m5
m2
m6
m4
m3
t4
t5
7. Remove the spacer (m6)and move to the
other side of the hinge pivot (m5).
8. Remove the lower door.
9. Remove using a tool the cover (b1).
Unscrew the lower hinge pivot (b2) and
the spacer (b3) and place them on the
opposite side.
10. Re-insert the cover (b1) on the opposite
side.
4. Remove the upper door.
5. Unscrew the screw and remove the door
stopper (d1). Attach it reversed on the
other side.
24
16. Fit the pin of the middle hinge (m5) into
the left-hand hole of the lower door.
b1
17. Re-insert the lower door on the pivot pin
(b2).
18. Re-screw the middle hinge (m1) on the
opposite side . Do not forget the plastic
spacer (m2) inserted under the middle
hinge.
19. Re-insert the upper door on the middle
hinge (m5).
b2
Make sure that the edges of the doors run
parallel to the side edge of the appliance.
b3
20. Position and fix the upper hinge (you can
find them in the instruction for use bag)
on the opposite side (t6).
11. Disassemble the door locking elements
(d2,d3) by unscrewing the screw (d4) .
d2
d4
d3
d6
d5
21. Insert the panel (t7) (that can be found in
the instruction for use bag).
22. Open the upper door, attach the top
cover (t2) using screws (t1). Insert the
magnet (d7). Close the door.
23. Reposition, level the appliance, wait for
at least four hours and then connect it to
the power socket.
12. Remove stoppers in both doors (d5,d6) .
13. Reverse the door locking elements
(d2,d3) , move to the other side of the
other door and fix by screwing in the
screw (d4) .
14. Re-insert the stoppers (d5,d6) on the
other side of the doors.
24. Unscrew the handles (h1) and fix them on
the opposite side.
15. Remove the left-hand cover pin of the
middle hinge (m3,m4) and move to the
other side.
Download from Www.Somanuals.c2om5. All Manuals Search And Download.
• All screws are tightened.
• The magnetic seal adheres to the cabinet.
• The door opens and closes correctly.
If the ambient temperature is cold (i.e. in
Winter), the gasket may not fit perfectly to the
cabinet. In that case, wait for the natural fitting
of the gasket.
h1
In case you do not want to carry out the above
mentioned operations, contact the nearest
After Sales Service Force. The After Sales
Service specialist will carry out the reversibility
of the doors at your cost.
Do a final check to make sure that:
Repairs - after sales service
Your appliance comes with a three year
warranty. If it is not working correctly; consult
the fault finding guides within this instruction
book (Something not working). If a fault
occurs which you can not resolve through
following the advice and information
contained within this instruction manual, the
next step is to contact our extended warranty
administrators on:
5. The model and serial number of the
appliance. So that you always have these
numbers at hand, we recommend you to
make a note of them here:
• Mod.......................................
• P.N.C.....................................
• S.N.........................................
IMPORTANT : If you call out an
engineer to a fault listed below, or to
repair a fault caused by incorrect use
or installation, a charge will be made
even if the appliance is under
guarantee.
0844 871 7771
They will give you details for your local Service
engineer. Before calling out an engineer,
please ensure you have read the details under
the heading “Something not working”.
When you contact your local service engineer
you will need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of fault
4. The purchase date as found on your
receipt
Spare parts
Always insist on genuine spare parts.
An authorised service engineer should service
this product, and only genuine spare parts
should be used. Under no circumstances
should you attempt to repair the appliance
yourself. Repairs carried out by inexperienced
persons may cause injury or serious
26
malfunctioning. Contact your local John Lewis
branch.
Environmental concerns
The symbol
on the product or on its
packaging indicates that this product may not
be treated as household waste. Instead it
should be taken to the appropriate collection
point for the recycling of electrical and
electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for
the environment and human health, which
could otherwise be caused by inappropriate
waste handling of this product. For more
detailed information about recycling of this
product, please contact your local council,
your household waste disposal service or the
shop where you purchased the product.
Download from Www.Somanuals.c2om7. All Manuals Search And Download.
John Lewis Partnership
171 Victoria Street
London SW1E 5NN
210620342-UK-00-17042009
925034086
925034087
925034270
925034271
925034272
|