Installation Guide
VM9224BT
EJECT
MUTE
A/V INPUT
VM9224BT
What’s in the Box
Tools and Supplies
You will need these tools and supplies to
install your VM9224BT:
VM9224BT Head Unit
Left and Right Double DIN
Mounting Brackets
•
Torx type, flat-head and Philips
screwdrivers
Double DIN Half Sleeve Install Bracket
External Microphone
•
•
Wire cutters and strippers
Tools to remove existing radio (screw
driver, socket wrench set or other tools)
Electrical tape
Crimping tool
Volt meter/test light
Crimp connections
18 gauge wire for power connections
16 – 18 gauge speaker wire
Two Custom Cosmetic Trim Rings
Parking Brake Wire
•
•
•
•
•
•
Hardware Bag
Speaker Output Harness
Power Input Harness
2 x Accessory Harness
Installation Guide
WARNING! Never install this unit where operation and viewing could interfere with
safe driving conditions.
1
Installation Using Half-Sleeve
Step 1-b
Install half-sleeve in the dashboard.
a. Install adapter if necessary (optional).
1
b. Install half-sleeve into adapter or dashboard (use only
the supplied screws). Do not force the sleeve into the
opening or cause it to bend or bow.
WARNING! Only connect the unit to a 12-volt power
supply with proper grounding.
c. Locate the series of bend-tabs along the top, bottom
and sides of the mounting sleeve. With the sleeve fully
inserted into the dashboard opening, bend as many of
the tabs outward as necessary so that the sleeve is
firmly secured to the dashboard.
Step 1-c
Use the M5 x 6 screws (provided) to install the mounting
brackets to each side of the radio using the holes indicated
2
TAB
in the diagram. DO NOT USE OTHER SCREWS.
Place the radio in front of the dashboard opening so the
wiring can be brought through the mounting sleeve.
3
DASHBOARD
Complete wiring as illustrated in the wiring diagram. Once
4
the wiring is complete, reconnect the battery negative
terminal. If there is no ACC available, connect the ACC lead
to the power supply with a switch.
Step 2
CAUTION! Be careful not to damage the car wiring.
After completing the wiring connections, turn the unit on
5
to confirm operation (ignition switch must be on). If unit does
not operate, recheck all wiring until problem is corrected.
Once proper operation is achieved, turn off the ignition
switch and proceed with final mounting of the chassis.
a. Connect wiring adapter to existing wiring harness.
b. Connect antenna lead.
c. Carefully slide the radio into the half-sleeve, making
sure it is right-side-up. Use the supplied screws to at-
tach the radio to the half sleeve.
Step 5-c
Using the Cosmetic Trim Ring
Two cosmetic trim rings are packaged with the head unit for
installation flexibility. This unit will fit into most import dashes
with little or no modification to the dash board/cavity. Some US
domestic vehicle dashes will accept a Double-DIN chassis, but
there is usually a small gap between the radio and dash piece af-
ter installation is complete. In this case, use the appropriate trim
ring to conceal any gaps that may be present.
NOTE: For proper operation of the CD/DVD player, the chassis
must be mounted within 30° of horizontal. Make sure the unit
is mounted within this limitation.
TRIM RING
MOUNTING
SLEEVE
3
Wiring Diagram
IMPORTANT: Incorrect wiring connections can damage the unit. Follow the wiring instructions carefully, or
have the installation handled by an experienced technician.
Need Help? For technical assistance, call the Jensen customer support line at 1-800-323-4815.
RADIO ANT
MICROPHONE
External Power Amplifier
WHITE
FRONT
FRONT
L
RED
WHITE
RED
R
REAR
L
REAR
R
BLUE
SUBWOOFER
YELLOW
Rear Video
VIDEO OUT
GPS
DVB-T
iPod
External
Microphone
Steering Wheel Control
(SWC) requires PAC
SWI-PS Interface Adapter,
Sold Separately
Antenna
Auto antenna
control (connect
to antenna control
lead and power
supply of antenna
amplifier)
Cell Phone
Rear View
Video Camera
-
BATTERY
4
|