User’s Manual
Electric and Ceran-Top Ranges
PTT052206
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THIS UNIT
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
This manual must be followed to reduce potential risk of fire, electric shock, or to prevent injury to persons or property
damage when using the range.
Please pay attention to these words, which will alert you about harmful situations, and follow all given instructions:
WARNING It may cause seriously harm, death or property damage if you do not follow instructions.
CAUTION It may cause injury or property damage if you do not follow instructions.
WARNING ANTI-TIP DEVICE
•
•
•
•
All ranges can tip.
Injury to persons could result.
Install anti-tip device packed with range.
See Installation Instructions.
To reduce the risk of tipping, the range must be secured by properly installed anti-tip bracket provided with the range.
Please refer to the anti-tip bracket installation instructions for proper installation.
SAFETY INFORMATION
General:
• Use this appliance only for its intended purpose as described in this manual.
• Proper Installation - Be sure your appliance is properly installed and grounded by a qualified technician.
• Never use your appliance for warming or heating the room.
• Do not leave children alone - Children should not be left alone or unattended in the area where appliance is in use.
They should never be allowed to sit or stand on any part of the appliance.
• Wear proper apparel – Loose-fitting or hanging garments should never be worn while using the appliance.
• User servicing - Do not repair or replace any part of the appliance unless specifically recommended in this manual.
All other servicing should be referred to a qualified technician.
• Storage in or on appliance - Flammable materials should not be stored in an oven, storage drawer or near surface
units.
• Do not use water on grease fires – Smother fire or flame, or use dry chemical or foam-type extinguisher.
• Use only dry potholders – Moist or damp potholders on hot surfaces may result in burns from steam. Do not let
potholders touch hot heating elements. Do not use a towel or other bulky cloth.
• WARNING Do not allow anyone stepping, leaning or sitting on the door or storage drawer of this unit. It may
damage the range and could tip it over, resulting in serious burns or other injury.
• CAUTION. Do not store items of interest to children in the cabinets above a range or on the back guard of a range
- children climbing on the range to reach items could be seriously injured.
• DO NOT TOUCH SURFACE UNITS, AREAS NEAR THESE UNITS, HEATING ELEMENTS OR INTERIOR
SURFACES OF THE OVEN. Both surfaces units and oven heating elements may be hot even though they are dark in
color. Areas near surface units and interior surfaces of an oven may become hot enough to cause burns. During and
after use, do not touch, or let clothing or other flammable materials contact surface units, areas near units, heating
elements or interior surfaces of oven until they have had sufficient time to cool. Among these surfaces are the cook
top, surfaces facing the cook top, the oven vent opening and surfaces near this opening, oven door and window.
3
Surface Cooking Units:
• Glazed cooking utensils – Only certain types of glass, glass/ceramic, ceramic, earthenware, or other glazed utensils are
suitable for range-top service without breaking due to the sudden change in temperature.
• Utensils handles should be turned inward and not extend over adjacent surface units – To reduce the risk of burns,
ignition of flammable materials, and spillage due to unintentional contact with the utensil, the handle of a utensil
should be positioned so that it is turned inward, and does not extend over adjacent surface units.
• Use proper pan size – This appliance is equipped with one or more surface units of different size. Select utensils
having flat bottoms large enough to cover the surface unit-heating element. The use of undersized utensils will expose
a portion of the heating element to direct contact and may result in ignition of clothing. Proper relationship of
utensils to burner will also improve efficiency.
• Never leave surface units unattended at high heat setting – Boil-over causes smoking and greasy spillovers that may
ignite.
For Coil Surface Elements Cook-top models:
o Make sure reflector pans or drip bowls are in place – Absence of these pans or bowls during cooking may
subject wiring or components underneath to damage.
o Protective liners – Do not use aluminum foil to line surface unit drip bowls or oven bottoms, except as
suggested in the manual. Improper installation of these liners may result in a risk of electric shock, or fire.
o Do not soak removable heating elements – Heating elements should never be immersed in water.
o Clean the cook top with caution – If a wet sponge is used to wipe spills on a hot cook top, be careful to avoid
steam burns.
o To avoid the possibility of a burn or electric shock, always be certain that the controls for all surface units
are at the OFF position and all coils are cool before attempting to lift or remove a unit.
For Ceramic Glass Cook-top models:
o Do not cook on broken cook top – If cook top should break, cleaning solutions and spillovers may penetrate
the broken cook top and create a risk of electric shock. Contact a qualified technician immediately.
o Never use the glass cook-top surface as a cutting area.
o Be careful when placing spoons or other stirring utensils on glass cook-top surface when it is in use. They
may become hot and could cause burns.
o Do not place or store items that can melt or catch fire on the glass cook-top, even when it is not being used.
o Clean cook top with caution – If a wet sponge or cloth is used to wipe spills on a hot cooking area, be careful
to avoid a steam burn. Some cleaners can produce noxious fumes if applied to a hot surface.
o Do not to leave a hot lid on the cook-top – As the cook-top cools, air can become trapped between the lid
and the cook-top and the ceramic glass could break when the lid is removed.
o Do not cook foods directly on the cook-top surface without a pan.
o Do not drop heavy or hard objects on the glass cook-top, they may cause it to crack.
Oven:
• Use care when opening oven door – Let hot air or steam escape before removing or replacing food.
• Do not heat unopened food containers – Build-up of pressure may cause container to burst and result in injury.
• Keep oven vent ducts unobstructed.
• Placement of oven racks – Always place oven racks in desired location while oven is cool. If rack must be moved
while oven is hot, do not let potholder contact hot heating element in oven.
COOK-TOP USE
SETTING SURFACE CONTROLS
How to Operate the Surface Elements (Coil Surface Elements Cook-top Models)
• Place cooking utensil on the surface element.
• Push in and turn the surface control knob in either direction to the desired setting. Start most cooking operations on
a higher setting and turn to a lower setting to finish cooking. The control knobs do not have to be set exactly on a
particular setting. Use the setting as a guide and adjust them as needed.
• When cooking is completed, turn the surface element off before removing the pan.
Note: The surface element on indicator light will glow when one or more elements are turned on. A quick glance at this
indicator light when cooking is finished is an easy way to be sure all surface elements are turned off.
How to Operate Radiant Surface Elements (Ceramic Glass Cook-top Models)
• Place correctly sized cookware on the radiant surface element.
• Push in and turn the surface control knob in either direction to the desired setting. Start most cooking operations on
a higher setting and turn to a lower setting to finish cooking. The control knobs do not have to be set exactly on a
particular setting. Use the settings as a guide and adjust them as needed. Each surface element provides a constant
amount of heat at each setting. A glowing red surface heating area extending beyond the bottom edge of the
cookware indicates the cookware is too small for the surface heating area.
• When cooking is completed, turn the surface element off before removing the pan.
Note: The surface element on indicator light will glow when one or more elements are turned on. A quick glance at this
indicator light when cooking is finished is an easy way to be sure all surface elements are turned off. The hot surface
indicator light will continue to glow after the control knob is turned to the OFF position and will glow until the heating
surface area has cooled sufficiently.
CAUTION Radiant surface elements may appear to have cooled after they have been turned off. The glass surface may
still be hot and burns may occur if the glass surface is touched before it has cooled sufficiently.
SUGGESTED SURFACE CONTROL SETTING (All Models)
Use the following chart as a guide when setting heat levels. Settings are based on cooking in medium-weight metal pans
with lids. They may vary when using other types of pans.
SETTING
HIGH (HI – 9)
RECOMMENDED USE
Start most foods, bring water to a boil, pan broiling
Continue a rapid boil, fry, deep fat fry
MEDIUM HIGH (7 – 8)
MEDIUM (5 – 6)
Maintain a slow boil, cook soups, thicken sauces and gravies, steam vegetables
Keep foods cooking, poach, stew
MEDIUM LOW (2 – 4)
LOW (LO – 1)
Keep food warm, melt, simmer
Note: The size and type of utensil used and the amount and type of food being cooked will influence the setting needed
for best cooking results.
5
COIL ELEMENTS AND BURNER BOWLS (Coil Surface Elements Cook-top Models)
•
•
•
Surface units should be level for optimal cooking results. Drip bowls, when clean, reflect heat back to the
cookware. They also help catch spills.
Cookware should have flat bottoms that make good contact with the entire surface unit. Check for flatness by
rotating a ruler across the bottom. There should be no gaps between the utensil and the ruler.
Utensil sizes should match with surface unit size. Pans should cover the entire element to absorb the maximum
heat. Avoid using an undersized utensil that would expose a portion of the surface unit, resulting in serious
burns or clothing ignition.
•
Pans should not extend more than one inch over the coil element. The bottom surface of the pan in this
situation could trap enough heat to cause discoloring of the burner bowl, damage to the surface units and or
crazing of the porcelain enamel range surface.
CERAMIC GLASS (Ceramic Glass Cook-top Models)
•
•
•
•
•
The surface cooking area will glow red when an element is on. It will cycle on and off, at all settings, to
maintain the selected heat level.
Wiping off the cook-top before and after each use will help keep it free from stains and provide the most even
heating. For more information, see “Care and Cleaning” section.
Use cookware about the same size as the surface cooking area. Cookware should not extend more than one
inch outside the area.
Use flat-bottomed cookware for best heat conduction and energy efficiency. Cookware with rounded, warped,
ribbed or dented bottoms could cause uneven heating and poor cooking results.
Determine flatness by placing the straight edge of a ruler, no space or light should be visible between it and the
cookware.
6
OVEN USE
BEFORE SETTING OVEN CONTROL
Oven Vent Location (Coil Surface Elements Cook-top Models)
•
•
The oven vent is located under the right rear surface unit. When the oven is on, warm air flows through the right
rear element. This venting is necessary for proper air circulation in the oven and good baking results.
DO NOT BLOCK OVEN VENT.
Arranging Oven Racks
•
•
To avoid possible burns, place racks in the desire position before turning the oven on.
Racks have stop-locks, so that when placed correctly on the supports, they will stop before coming completely
out, and will not tilt.
•
Do not move racks with bake ware on them.
To remove, pull the rack out until the stop position, raise the front edge and slide out.
To replace, fit the rack onto the guides on the oven walls. Tilt the front of the rack upward and slide it back into place.
Recommended Rack Positions for Broiling, Baking, and Roasting
FOOD
RACK POSITION
Broiling meats, chicken or fish
1 or 2
Cookies, cakes, pies, biscuits and muffins
2 or 3
Broiling fish, medium steaks, hamburgers and chops
Broiling well-done foods such as chicken and lobster
Frozen pies, angel food cake, yeast bread, casseroles, small cuts of meat or poultry
Turkey, roast or ham
2
3
4
4
Air Circulation into the Oven
•
•
To cook food evenly, hot air must be able to circulate.
For best air circulation and baking results allow two inches of space around bake ware and be sure pans and
bake ware do not touch each other, the oven door, sides or back of the oven cavity.
•
The hot air must circulate around the pans and bake ware in the oven for even heat to reach around the food.
NUMBER OF PANS
POSITION ON RACK
1
2
Center of rack
Side by side or slightly staggered
3 or 4
Opposite corners on each rack. Make that no bake ware piece is directly over another.
7
HOW TO OPERATE THE OVEN
NOTE The oven indicator light will glow when there is electric power to the bake element. When the oven
temperature setting is reached, the indicator light will go off. It lights up again when the power comes back on the bake
element.
The oven indicator light glows until the oven reaches your selected temperature, then goes OFF and ON with the oven
element(s) during cooking.
Baking
Before baking, positions racks and bake ware according to “Arranging oven racks and Air circulation in the oven”
sections.
1. Preheat the oven before start baking. To preheat, set the oven at the correct temperature. Preheating is necessary
for good results when baking cakes, cookies, pastry and breads. Preheat the oven for 10 minutes.
2. Turn the oven control clockwise to the temperature setting desired. Check food for doneness at the minimum
time shown in the recipe. Cook longer if necessary.
3. Turn the oven control knob OFF when cooking is complete.
Broiling
Before broiling, position rack according to “Arranging oven racks” section.
•
To broil, turn the oven control clockwise to BROIL. It is not necessary to preheat the oven unless recommended
in the recipe. Position food on broiler pan provided with the range. It is designed to drain juices and help prevent
spatter and smoke. Close the door to the broil stop position to ensure proper broiling temperature.
Broil on one side until food is browned, turn and cook on the second side. Always pull the rack out to the stop
position before turning or removing food.
•
•
Turn the oven control knob OFF when cooking is complete.
CAUTION Should an oven fire occur, close the oven door and turn OFF the oven. If the fire continues, use a fire
extinguisher. DO NOT put water or flour on the fire. Flour may be explosive.
SETTING THE CLOCK AND TIMER (Some Models)
TO SET THE CLOCK
•
•
•
Press and hold the CLOCK pad.
Press the UP or DOWN ARROW pads to select the time of day.
Press the CLOCK pad to start.
TO SET THE TIMER
•
•
Press the TIMER pad.
Press the UP or DOWN ARROW pads to increase or decrease the time in one-minute increments. Press and hold the
pads to increase or decrease the time in 10-minute increments. The timer can be set for any amount of time from
00:01 minutes to 11:59 hours.
•
Press the TIMER pad to start.
NOTES: The timer does not start or stop cooking. It serves as an extra timer in the kitchen that will beep when the set
time has run out. While the timer is active, press and hold the UP or DOWN ARROW pads to increase or decrease the
time. To cancel the timer before the set time has run out, press the CLOCK pad.
8
GENERAL CARE AND CLEANING
WARNING Before cleaning, make sure all controls are OFF and the oven and cook-top are cool. Always follow label
instructions on cleaning products. Soap, water, and a soft cloth or sponge are suggested first unless otherwise noted.
SURFACES
HOW TO CLEAN
Porcelain Enamel Surfaces
•
The porcelain enamel finish is sturdy but breakable if misused. This finish is acid-resistant.
However, any acidic foods spilled (such as fruit juices, tomato or vinegar) should not be
permitted to remain on the finish.
•
•
•
If acids spill on the cook-top while it is hot, use a dry paper towel or cloth to wipe it up
right away. When the surface has cooled, wash wish soap and water. Rinse well.
Painted surfaces include the sides of the range. Clean these with soap and water or vinegar
and water solution.
Do not use commercial oven cleaners, cleaning powders, steel wool or harsh abrasives on
any painted surfaces.
Painted Surfaces
Control Panel and Knobs
•
•
The Clean up spatters with a damp cloth. Remove heavier soil with warm, soapy water.
The control knobs may be removed for easier cleaning. To remove a knob, pull it straight
off the stem. Wash the knob in soap and water but do not soak.
Be sure all the controls are turned OFF and the surface units are cool before attempting to remove
them.
Coil Elements
(Coil Surface Elements Models)
To clean the surface units, turn the control to the highest setting for a minute. The coils will burn
off any soil.
To remove:
•
Push in the edge of surface unit toward the receptacle. Then lift it just enough to clear the
burner bowl. Do not lift the surface unit more than 25 mm (1 in.)
Pull the surface unit straight away from the receptacle.
Lift out the burner bowl.
•
•
To replace:
•
•
Line up openings in the burner bowl with the surface unit receptacle.
Holding the surface unit as level as possible, carefully push surface unit terminal into the
receptacle.
•
When the terminal is pushed into the receptacle as far as it will go, push down the edge of the
surface unit opposite the receptacle.
Do not immerse the surface units in liquids of any kind. Do not clean the surface unit in a
dishwasher. Do not bend the surface unit plug terminals.
Drip Bowls
(Coil Surface Elements Models)
•
•
Remove the surface units. Then lift out the drip bowls.
For best results, clean the drip bowls by hand. Place them in a covered container with ¼
cup ammonia to loosen the soil. Then scrub with a soap-filled scouring pad. Rinse with
clean water and polish with a clean soft cloth.
•
•
•
Clean the area under the drip bowls often. Built-up soil, specially grease, may catch fire.
Clean only porcelain enamel drip bowls in a dishwasher, not chrome.
Do not cover the drip bowls with foil. Using foil so close to the receptacle could cause
shock, fire or damage to the range.
9
Lift Up Cook-top
(Coil Surface Elements Models)
•
•
The cook-top can be lifted up for easier cleaning. The entire cook-top may be lifted up and
supported in the up position.
The surface units do not need to be removed; however, you may remove one to make
raising the cook-top easier. There are two side supports that lock into position when the
cook-top is lifted up.
•
•
•
After cleaning under the cook-top wit hot, mild soapy water and clean cloth, lower the
cook-top. Be careful not to pinch your fingers.
To lower the cook-top, push the rods back and gently lower the cook-top until it rests in
place.
Oven Vent
(Coil Surface Elements Models)
Never cover the opening with aluminum foil or any other material.
Glass Cook-top
(Ceramic Glass Cook-top
Models)
IMPORTANT: Prior to using your cook-top for the first time, apply some of the cook-top cleaning
cream supplied with your new range. Buff with a non-abrasive cloth or pad such a no scratch scrub
sponge. This will make cleaning easier when soiled from cooking. The special cook-top cleaning
cream leaves a protective finish on the glass to help prevent scratches and abrasion.
Also clean the glass surface after each use. This helps protect the top and makes clean up easier.
To clean the cook-top seal around the edge of the glass, let a wet cloth rest on it for a few minutes,
then wipe clean. Use a mild detergent if needed. Do not use a knife or any sharp object on the seal
because it will cut or damage it.
Sliding aluminum or cooper clad bottom pans on the cook-top can cause metal markings on the
cook-top surface. These marks should be removed immediately after the cook-top has cooled using
the cook-top cleaning cream. Metal marks can become permanent if not removed prior to future
use.
For light to moderate soil:
•
Apply a few drops of the cook-top cleaning cream (cleaner must be recommended for Ceramic
Glass cook-top) directly to the cook-top. Use a paper towel or a no scratch scrub sponge to
clean the entire cook-top surface. Make sure the cook-top is cleaned thoroughly, leaving no
residue.
For heavy, burned on soil:
•
Apply a few drops of the cook-top cleaning cream (cleaner must be recommended for Ceramic
Glass cook-top) directly to the soiled area. Rub the soiled area using a no scratch scrub sponge,
applying pressure as needed. Once the sponge has been used on the cook-top, do not use the
sponge for any other purpose.
•
•
If soils remain, carefully scrape soils with a metal razor blade scraper, holding scraper at a 30-
degree angle to the surface. Remove loosened soils with cook-top cleaner and buff surface
clean.
Store razor blades out of the reach of children.
Plastic or foods with a high sugar content:
•
These types of soils need be remove immediately if spilled or melted onto the ceramic cook-top
surface. Permanent damage (such as pitting of the cook-top surface) may occur if not removed
immediately. After turning the surface elements OFF, use a razor blade scraper or a metal
spatula with a mitt and scrape the soil from the hot surface (as illustrated). Allow the cook-top
to cool, and use the same method for heavy or burner on soils.
The oven door is removable for cleaning.
Lift-Off Oven Door
To remove:
•
•
Open the door to the fully opened position.
Pull up the lock located on both hinge supports and engage it in the hook of the hinge levers.
You may have to apply a little downward pressure on the door to pull the lock fully over the
hooks.
•
Grasp the door by the sides; pull the bottom of the door up and toward you to disengage the
hinge supports. Keep pulling the bottom of the door toward you while rotating the top of the
door toward the range to completely disengage the hinge levers.
To replace:
Proceed in reverse to reinstall the door. Make sure the hinge supports are fully engaged before
unlocking the hinge levers.
•
10
To clean the inside of the door:
•
Soap and water will normally do the job. Heavy spattering or spillovers may require cleaning
with a mild abrasive cleaner.
•
Soap-filled, steel wool pads may also be used.
To clean the outside of the door:
•
•
•
•
•
Use soap and water to thoroughly clean the top, sides and front of the oven door. Rinse well.
Use a glass cleaner to clean the glass on the outside of the door.
Do not let water drip into the vent openings.
Oven Cavity
Do not use oven cleaners.
Soap and water will normally do the job. Heavy spattering or spillovers may require cleaning
with a mild abrasive cleaner. Soap-filled, steel wool pads may also be used.
Be sure to wear rubber gloves to protect your hands.
To clean the oven bottom, gently lift the bake element. This will allow easier access to the oven
bottom for cleaning. Be careful not to raise the element more than 4 to 5 inches from the resting
position. Clean with warm soapy water.
•
•
Oven Heating Elements
Oven Racks
•
•
•
Do not clean the oven heating elements. Any soil will burn off when the elements are heated.
Clean the racks with an abrasive cleaner or steel wool.
To make the racks slide more easily apply a small amount of vegetable oil or cooking oil to a
paper towel and wipe the edges of the racks with it.
Broiler Pan
•
•
After broiling, remove the broiler pan from the oven. Carefully pour out the grease from the
pan into a proper container.
Wash and rinse the broiler pan in hot water with soap-filled or plastic scouring pad. If food has
burned on, sprinkle with detergent while hot and cover with wet paper towels or a dishcloth.
Soaking the pan will remove burned-on foods.
•
It may be cleaned with a commercial oven cleaner. The broiler pan can also be cleaned in the
dishwasher.
Oven Light
(Some Models)
•
Before replacing the oven light bulb, turn the oven light OFF. Replace bulb with a 40-watts
household appliance bulb.
The storage drawer can be removed. Before removing, make sure drawer is cool and empty.
Storage Drawer
(Some Models)
To remove:
•
•
•
•
Open drawer to its full open position.
Locate the black tabs on both sides of the drawer.
Press the tabs on both right and left side at the same time, then pull drawer out another inch.
Holding the drawer by its sides, not its front, carefully pull it all the way out.
To replace:
•
•
•
Align the drawer glides with the receiving guides.
Push drawer in all the way.
Gently open and close the drawer to ensure it is seated properly on the slides.
11
BEFORE YOU CALL FOR SERVICE
IMPORTANT Before you call for service, review this list. It may save you time and expense. The list includes common
occurrences that are not the result of defective workmanship or materials in this appliance.
OCCURRENCE
POSSIBLE CAUSE
SOLUTION
a) Make sure cord plug is plugged tightly into a) Check it.
grounded outlet.
1) Surface Elements Or Oven
Not Will Operate
b) A household fuse been blown or has the
circuit breaker been tripped.
b) Replace the fuse or reset the circuit.
c) Service wiring is not complete.
c) Contact your dealer, installing agent or
authorized service.
d) Power outage.
d) Check house lights to be sure. Call your
local electric company for service.
a) Lightweight or warped pans used.
a) Use only flat, evenly balanced, medium or
heavyweight cookware. Flat pans heat
better than warped pans. Cookware
materials and weight of the material affect
heating. Heavy and medium-weight pans
heat evenly. Because lightweight pans heat
unevenly, foods may burn easily.
2) Surface Elements Do Not Heat
Properly
b) No power to the appliance.
b) Check steps under Occurrence (1)
c) Incorrect control setting.
c) Make sure the correct control is on for the
surface unit to be used.
d) The surface units are not plugged in solidly.
d) With controls off, check to make sure the
surface unit in plugged completely into the
receptacle.
a) Foods with acids, such as tomatoes, if
allowed to stand in/on bowls will cause
corrosion.
a) Remove and wash drip bowls as soon as
possible after a spillover.
3) Drip Bowls Are Pitting Or
Rusting
(Coil Surface Elements Models)
b) Environment.
b) Houses along seacoast are exposed to salt
air. Protect bowls as much as possible from
direct exposure to salt air.
a) Bottom surface of cookware extends
beyond surface elements and touches cook-
top surface
a) This can cause high enough temperatures to
discolor the drip bowls. DO NOT use
cookware of this type. Pan sizes should be
matched to the size of the element.
a) Be sure cook-top surface and bottoms of
utensils are clean before usage. Small
scratches do not affect cooking and will
become less visible with time.
4) Drip Bowls Are Turning Color
Or Distorted
(Coil Surface Elements Models)
a) Coarse particles such as salt or sand
between cook-top and utensils can cause
scratches.
5) Scratches Or Abrasions On
Cook-top Surface
(Ceramic Glass Cook-top
Models)
b) Cleaning materials not recommended for
ceramic glass cook-top have been used.
c) Cookware with rough bottom has been
used.
b) Check them.
c) Use smooth, flat-bottomed cookware.
a) Sliding or scraping of metal utensils on
cook-top surface
a) Do not slide metal utensils on cook-top
surface. Use a ceramic glass cook-top
cleaning cream to remove the marks.
6) Metal Marks
(Ceramic Glass Cook-top
Models)
a) Boil-overs are cooked onto surface
a) Use a razor blade scraper to remove soil.
7) Brown Streaks Or Specks
(Ceramic Glass Cook-top
Models)
a) Mineral deposits from water and food.
Remove using a ceramic glass cook-top
cleaning cream
a) Use cookware with clean, dry bottoms.
8) Areas Of Discolorations With
Metallic Sheen
(Ceramic Glass Cook-top
Models)
a) The hot surface indicator light stay on after a) Check it.
control knob(s) have been turned OFF.
9) Hot Surface Indicator Light
Stays On
(Ceramic Glass Cook-top
Models)
12
a) Improper cookware being used/
a) Many factors affect baking results.
a) Use only flat cookware to minimize cycling.
10) Frequent Cycling Off And
On Surface Units
(Ceramic Glass Cook-top
Models)
a) Make sure the proper rack position is used.
Center food in the oven and space pans to
allow air to circulate. Allow the oven to
preheat to the set temperature before
placing food in the oven. Try adjusting the
recipes recommended temperature or
baking time.
11) Poor Baking Results
a) This is the sound of the heating element
turning off and on during cooking
functions.
a) This is normal.
12) Oven Makes Clicking Noise
13) Oven Door Is Crooked
a) The door is out of position
a) Because the oven door is removable; it is
sometimes gets out of position during
installation. To straighten the door, see
“Care and Cleaning” in this Guide.
a) See “Care and Cleaning” in this Guide.
b) Call for Service.
a) Replace or tighten bulb.
b) Switch operating light is broken.
14) Oven Light Does Not Work
(Some Models)
13
© 2006 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions.
®
All rights reserved. Sunbeam is a registered trademark of Sunbeam Products,
Inc. used under license. Distributed by Petters Consumer Brands, LLC. 4400
Baker Road, Minnetonka, MN 55343.
For service, support and warranty information, visit www.sunbeammajorappliances.com or in the US call 1-866-866-6283.
14
|