VIDEO CASSETTE RECORDER
HR-A590U
INSTRUCTIONS
Printed in Thailand
LPT0662-001A
COPYRIGHT © 2002 VICTOR COMPANY OF JAPAN, LTD.
K
4F21901A
01/12
Dear Customer,
CAUTION:
Thank you for purchasing the JVC VHS video cassette recorder.
Before use, please read the safety information and precautions to
ensure safe use of your new VCR.
Changes or modifications not approved by JVC could void user’s
authority to operate the equipment.
Failure to heed the following precautions may result in damage
to the VCR, Remote or video cassette.
CAUTIONS
1
DO NOT place the VCR . . .
...in an environment prone to extreme temperatures or humidity.
...in direct sunlight.
...in a dusty environment.
...in an environment where strong magnetic fields are generated.
...on a surface that is unstable or subject to vibration.
2. DO NOT block the VCR’s ventilation openings.
3. DO NOT place heavy objects on the VCR or on the Remote.
4. DO NOT place anything which might spill on the top of the VCR
or on the Remote.
5. AVOID violent shocks to the VCR during transport.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
For Customer Use:
Enter below the Model No. and Serial No. which are located
on the rear of cabinet. Retain this information for future
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
reference.
Model No.
Serial No.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
UNIT TO RAIN OR MOISTURE.
• Cassettes marked “VHS” (or “S-VHS”) can be used with this video
cassette recorder. However, S-VHS recording is not possible with
this model.
• This model is equipped with SQPB (S-VHS QUASI PLAYBACK)
that makes it possible to play back S-VHS recordings with
regular VHS resolution.
• HQ VHS is compatible with existing VHS equipment.
• As an Energy Star® Partner, JVC has determined that this
product or product model meets the Energy Star® guidelines for
energy efficiency.
CAUTION:
This video cassette recorder should be used with AC 120V~, 60Hz
only.
To prevent electric shocks and fire hazards, DO NOT use any other
power source.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG
TO WIDE SLOT, FULLY INSERT.
ATTENTION:
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME
LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides guidelines
for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
d. If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to restore
the product to its normal operation.
Buttons, Connectors and Indicators
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in performance—
this indicates a need for service.
Front Panel
REC
3. Replacement Parts
POWER
When replacement parts are required, be sure the service technician
has used replacement parts specified by the manufacturer or which
have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or other hazards.
STOP/EJECT
Cassette loading slot
PLAY
PLAY
4. Safety Check
Upon completion of any service or repairs to this product, ask the
service technician to perform safety checks to determine that the
product is in safe operating condition.
POWER
REW
FF
STOP/EJECT
CH
VIDEO (MONO)
L
–
AUDIO
–
R
TV/VCR
TIMER
REC
POWER
REC
How to use the Remote
Before use, insert two AAA size batteries into the Remote with the
VIDEO/AUDIO input
connectors
CH–/+
FF
polarity ( and ) matched correctly as indicated on the battery
REW
compartment or on the lid.
TV/VCR indicator
TIMER indicator POWER indicator
REC indicator
Remote sensor
• Point the Remote toward the remote sensor on the target
component.
• The maximum operating distance of the remote control is about 5
m.
NOTE:
If the Remote does not work properly, remove its batteries, wait for a
few seconds, replace the batteries and then try again.
Rear Panel
Video heads cleaning
AC power cord
Use a dry cleaning cassette — TCL-2— when:
• Rough, poor picture appears while a tape is played back.
• The picture is unclear or no picture appears.
UHF/VHF IN (ANT)
UHF/VHF
OUT
IN(ANT)
VIDEO
L
OUT(TV)
AUDIO
CH
R
3
4
AUDIO/VIDEO OUT
3/4 CHANNEL
SELECTTOR SWITCH
UHF/VHF OUT (TV)
– Buttons, Connectors and Indicators –
Remote
Connections and VCR channel
Setting
POWER
POWER
Check contents
Make sure the package contains all of the accessories listed
in “Specifications”.
1
1
4
7
2
5
8
3
6
9
Number keys
CH–/+
Situate VCR
2
AUX
REC
Place the VCR on a stable, horizontal surface.
+
–
CH
0(AUX)
PAUSE
PLAY
Connect VCR to TV
3
REC
PAUSE
PLAY
REW
Antenna or cable
Coaxial cable
REW
FF
FF
STOP
ENTER
TIMER
MENU
ENTER
STOP
SET
MENU
Flat feeder
+
–
Matching transformer
(not supplied)
CANCEL
C.RESET
SP/EP
CANCEL
SET–/+
TV/VCR
TV/VCR
TIMER
SP/EP
–
C.RESET
DISPLAY
+
A.MONITOR
TV POWER
INPUT
UHF/VHF
IN(ANT)
OUT
A.MONITOR
TV CH
DISPLAY
VIDEO
TV POWER
INPUT
–
+
TV VOL
AC power cord
L
TV CH–/+
OUT(TV)
AUDIO
TV VOL–/+
R
CH
3
4
V)
AUD
R
This Remote transmit A code
signals only; it is not applicable
to B code signals.
Back of VCR
AC outlet
On-screen display
To audio/video input connectors
If you press DISPLAY on the Remote, you can see the current VCR
status on the TV screen. Press DISPLAY again to exit on-screen
display.
The indications are not recorded even if the VCR is in the recording
mode.
Audio/video cable
(not supplied)
WHILE WATCHING TV
RF cable
(supplied)
TV
To 75 Ω terminal
RF Connection
DAY AND CLOCK TIME
8 : 30 AM THU
STEREO SAP
CH 125
CHANNEL
1
Disconnect the TV antenna from the TV.
Connect the TV antenna cable to the UHF/VHF IN
terminal on the rear of the VCR.
2
STEREO AND
SEPARATE AUDIO
PROGRAM (SAP)
3
Connect the supplied RF cable between the UHF/VHF
OUT terminal on the rear of the VCR and the TV’s
antenna input terminal.
TAPE
OUTPUT
STEREO
00 : 00 : 00 SP
SPEED
SELECTION
REAL TIME COUNTER
AV Connection
WHILE OPERATING A TAPE
(improves picture quality during tape playback.)
If your TV is equipped with audio/video input connectors
OPERATING MODE
1
Connect the antenna, VCR and TV as shown in the
8 : 30 AM THU
CH 125
illustration.
HI-FI
HI-FI STEREO
2
Connect an audio/video cable between the AUDIO/
VIDEO OUT connectors on the rear of the VCR and the
audio/video input connectors on the TV.
• Even if you are using audio/video cables to connect your
VCR to your TV, you must also connect it using the RF
cable. This will ensure that you can record one show while
watching another.
AUTO REPEAT
TAPE IN
AUTO TRACKING
AUTO TR.
STEREO
00 : 00 : 00 SP
OUTPUT
SELECTION
– Connections and VCR channel Setting –
Initial Settings
4
Set VCR channel
To view playback of a recorded tape, or to watch a program
selected by the VCR's channel selector, the TV must be set to
channel 3 or 4 (video channel) when a TV is connected with
the 75 ohm coaxial cable only.
Language Setting
MENU
CLOCK SET
TIMER REC SET
AUTO REPEAT
CH SET UP
SAP
The default setting is “ENGLISH”.
ON OFF
ON OFF
Access Menu screen
1
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
Press MENU on the Remote. Press
SET –/+ to select “LANGUAGE”, then
press ENTER.
1
Set the 3/4 Channel selector switch (Rear of the VCR) to
CH 3 or 4.
Turn ON the TV and set to CH 3 or 4 to correspond with
the channel selected in 1.
ON OFF
⟨+/–/ENTER/MENU⟩
2
Select language
2
LANGUAGE/IDIOMA/LANGUE
ENGLISH
3
4
Press POWER to turn on the VCR.
The POWER indicator will light.
This VCR offers you the language
choice to view menus and some
messages — in English, Spanish or
French. Press SET –/+ to select your
desired language, then press ENTER.
ESPAÑOL
FRANCAIS
Press TV/VCR to select the VCR
⟨
+ – ⟩
/ /ENTER/MENU
position.
CH 125
The TV/VCR indicator will light.
Press MENU twice to return to normal screen.
5
Select any channel to receive a
TV station in your area.
Clock Setting
Preparations
You must set the date and time for timer recording.
The channel number will appear
on the screen for about 4 seconds.
MENU
CLOCK SET
Access Menu screen
1
TIMER REC SET
AUTO REPEAT
CH SET UP
SAP
ON OFF
ON OFF
Press MENU on the Remote. Press
SET –/+ to select “CLOCK SET”, then
press ENTER.
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
⟨+/–/ENTER/MENU⟩
Set month, day, year and time
2
MONTH
DAY
10
1
(SUN)
Press SET –/+ until the desired month
appears, then press ENTER. Set the
day, year and time in the same way.
YEAR
TIME
2000
12
:
00 AM
+ —
/
/ENTER/CANCEL/MENU
3 Start clock
Press MENU twice and normal screen
appears.
⟨
⟩
To make corrections any time during the process
Press CANCEL repeatedly until the item you want to change
blinks, then press SET –/+.
NOTE:
After a power failure or disconnection of the power, the
timer settings will be lost. In this case, reset the present time.
– Initial Settings –
Tuner Setting
Setting channels manually
– Manual Channel Set
This VCR is equipped with a channel memory feature which
allows channels to skip up or down to the next channel set
into memory, skipping over unwanted channels. Before
selecting channels, they must be programmed into the VCR’s
memory. In addition to normal VHF and UHF channels, this
VCR can receive up to 113 Cable TV channels. To use this
VCR with an antenna, set the TV/CATV menu option to the
TV mode. When shipped from the factory, this menu option
is in the CATV mode.
You can add the channels you want or delete the channels
you do not want manually.
MENU
Access Menu screen, then CH
Set Up screen
1
CLOCK SET
TIMER REC SET
AUTO REPEAT
CH SET UP
SAP
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
ON OFF
Press MENU on the Remote. Press
SET –/+ to select “CH SET UP”, then
press ENTER.
ON OFF
⟨+/–/ENTER/MENU⟩
– TV/CATV Selection
CH SET UP
Access ADD/DELETE Mode
2
TV CATV
AUTO CH MEMORY
ADD/DELETE
Access Menu screen, then CH
Set Up screen
MENU
CLOCK SET
TIMER REC SET
AUTO REPEAT
CH SET UP
SAP
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
Press SET –/+ to select “ADD/
DELETE”, then press ENTER.
1
ON OFF
ON OFF
Press MENU on the Remote. Press
SET –/+ to select “CH SET UP”, then
press ENTER.
⟨
+ – ⟩
/ /ENTER/MENU
ON OFF
⟨+/–/ENTER/MENU⟩
Add or Delete desired channels
3
ADD
CH 012
Perform TV/CATV Selection
CH SET UP
2
1
Press SET –/+ on the Remote to
select a channel number you
want to add or delete.
TV CATV
AUTO CH MEMORY
ADD/DELETE
Press SET –/+ to select “TV/CATV”,
then press ENTER to select the TV
or CATV mode. The arrow indicates
the selected mode.
⟨
+ – ⟩
/ /ENTER/MENU
2
To add channels
⟨
+ – ⟩
/ /ENTER/MENU
Press ENTER until “ADD” appears on the screen to set to
add the unmemorized channel.
TV
- VHF/UHF channels
CATV - CABLE TV channels
To delete channels
Press ENTER until “DELETE” appears on the screen to set
to delete the channel from memory.
Press MENU twice to return to normal screen.
Repeat to to add or delete other channel.
1
2
Setting channels automatically
– Auto Channel Memory
3
Press MENU three times three times to return to normal
screen.
The VCR can receive a maximum of
MENU
CLOCK SET
TIMER REC SET
AUTO REPEAT
CH SET UP
SAP
181 channels by presetting the
channels into memory.
NOTE: You can’t select “CH SET UP” if you set the channel
ON OFF
ON OFF
to “L”.
Access Menu screen, then CH
Set Up screen
1
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
⟨+/–/ENTER/MENU⟩
Press MENU on the Remote. Press
SET –/+ to select “CH SET UP”, then
press ENTER.
CH SET UP
TV CATV
AUTO CH MEMORY
ADD/DELETE
2
Perform Auto Channel Memory
Press SET –/+ to select “AUTO CH
MEMORY”, then press ENTER.
⟨
+ – ⟩
/ /ENTER/MENU
3
Complete Auto Channel Memory
The auto tuning will start. The
channel display will count up and
when finished, the screen returns to
normal.
CH 001
Playback
Slow-motion
Press PLAY ( ) on the
Remote.
• Playback will proceed at
1/10 th of the normal speed.
• Press PLAY ( ) to resume
normal playback.
OR Press Play ( ) on the
Basic Playback
VCR.
Load a cassette
1
PLAY
NOTE:
During slow motion picture, some noise might appear on
the TV screen. Use the SET–/+ on the Remote to eliminate
the noise.
POWER
REW
FF
STOP/EJECT
CH
VIDEO (MONO)
L
–
AUDIO
–
R
TV/VCR
TIMER
REC
POWER
REC
However, the VCR will turn to the default setting once a
power failure occurs.
Make sure the window side is up, the rear
label side is facing you and the arrow on
the front of the cassette is pointing
towards the VCR.
Speed search
Press REW (
) or FF
OR Press REW (
) or
(
) on the Remote.
FF ( ) on the VCR.
• Do not apply too much pressure when
inserting.
• Press PLAY ( ) to resume
normal playback.
• The VCR turns on, and the counter on
the on-screen display is reset, automatically.
Variable speed search
• If the cassette’s record safety tab has been removed, playback
begins automatically.
Press REW (
) or FF
OR Press REW (
) or FF
Start playback
2
(
) repeatedly on the
(
) repeatedly on
Remote.
the VCR.
Press PLAY (
).
• Press PLAY ( ) to resume
normal playback.
• Each time you press REW
(
) or FF (
) the
playback speed changes.
During playback
Stop playback
TAPE SPEED
PICTURE SEARCH SPEED
PRESS ONCE
PRESS TWICE
5X
15X
OR Press STOP/EJECT (■/
on the VCR.
Press STOP ( ) on the
SP
EP
3X
9X
)
Remote.
When the tape is not running
Rewind/fast-forward
OR Press REW (
) or FF
Press REW (
) or FF
(
) on the VCR.
(
) on the Remote.
Pause playback and view still picture
Press PAUSE.
• Press PLAY ( ) to resume
normal playback.
Eject the tape
Press STOP/EJECT (■/ ) on
the VCR.
Pause and Frame-by-Frame playback
• You can also eject the
cassette when the VCR is
turned off.
Press PAUSE to pause, then
press PAUSE repeatedly.
Press PLAY ( ) to resume
normal playback.
Turn off the VCR
Press POWER on the
Remote.
OR Press POWER ( /l) on
the VCR.
– Playback –
Playback Features
Recording
It may be unlawful to record or play back copyrighted
material without the consent of the copyright owner.
Accidental erasure prevention
Adjusting tracking condition
– Tracking Adjustment
Automatic tracking adjustment
Whenever you insert a tape and start playback, automatic
tracking starts working and continuously analyzes the signal
to enable optimum picture quality during playback.
Manual tracking adjustment
If automatic tracking cannot eliminate noises well during
playback, press SET –/+ on the Remote to eliminate the
noises. Press it briefly for a fine adjustment, or press and
hold for a coarse adjustment.
To prevent accidental recording on a recorded cassette,
remove its record safety tab. To record on
it later, cover the hole with adhesive
tape.
Record safety tab
Basic Recording
Load a cassette
1
Make sure the record safety tab is
intact. If not, cover the hole with
adhesive tape before inserting the
cassette.
• Press SP/EP on the Remote again to reactivate automatic
tracking.
• The VCR turns on, and the counter
is reset, automatically.
2 Select recording channel
Press CH–/+ or the Number keys on
the Remote [CH–/+ on the VCR].
CH 001
Playing back tape repeatedly
– Auto Repeat Play
• If you connect the TV and the VCR
only using the RF connection, press
TV/VCR on the Remote so that the
TV/VCR indicator lights to view the program to be
recorded.
MENU
CLOCK SET
TIMER REC SET
AUTO REPEAT
CH SET UP
SAP
Access Menu screen
Press MENU on the Remote.
1
ON OFF
ON OFF
Press SET –/+ to select “AUTO
REPEAT”.
LANGUAGE/IDIOMA/LANGUE
Set tape speed
Press SP/EP.
3
NO NOISE BACKGROUND
ON OFF
⟨+/–/ENTER/MENU⟩
MENU
CLOCK SET
TIMER REC SET
AUTO REPEAT
CH SET UP
SAP
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
Select ON/OFF
Press ENTER to select “ON” or
“OFF”.
Press MENU to return to normal
screen.
2
3
00 : 00 : 00 SP
ON OFF
ON OFF
4
Start recording
CH 110
ON OFF
On the VCR, press REC. Or on the
⟨+/–/ENTER/MENU⟩
Remote, while holding REC, press
PLAY ( ).
Start Auto Repeat Play
Press PLAY. The tape will play
over and over until the repeat
mode is canceled.
The REC indicator will light.
During recording
Pause recording
Press PAUSE.
• Press PAUSE to resume recording.
• You can select channel in the
recording pause mode.
Stop recording
OR Press STOP/EJECT
(■/ ) on the VCR.
Press STOP ( ) on the
Remote.
– Recording –
Recording Features
Timer Recording
Specifying recording length
Timer recording can be programmed on-screen with
the remote control. The built-in timer allows automatic
unattended recording of up to 8 programs within 1
month.
- One Touch Timer Recording (OTR)
The One-touch Timer Recording feature provides a
simple and convenient way to make a timed
recording.
NOTES:
EXAMPLE: One-touch Timer Recording for 30 minutes.
• After timer recording is completed, the VCR turns off
automatically.
When a TV is connected with an audio/video cable, turn the
TV on and select the video input mode on the TV.
• You can program the timer recording while a regular
recording is in progress; the menu screens will not be
recorded.
• The timer recording will start at 20 seconds before the
time you predetermined.
Load a cassette tape with the
erase prevention tab intact.
1
EXAMPLE: Program a timer recording for the 26th day,
channel 125 (CATV), 11:00 - 11:30 PM on timer program
number 1 (Tape speed: EP).
Press SP/EP to select the desired
tape speed SP or EP.
The counter and SP or EP will
appear on the screen for about 4
seconds.
2
3
4
When a TV is connected with an audio/video cable, turn the
TV and this VCR on and select the video input mode on the
TV.
00 : 00 : 00 SP
CH 125
MENU
Press MENU on the Remote.
1
CLOCK SET
TIMER REC SET
AUTO REPEAT
CH SET UP
SAP
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
Press the Number keys or CH –/+
to select the channel to be
recorded.
The channel number will appear
on the screen and display for
about 4 seconds.
Check the “TIMER REC SET”
option is selected, then press
ENTER.
ON OFF
ON OFF
ON OFF
⟨+/–/ENTER/MENU⟩
Press SET –/+ to select one
of the program lines, then
press ENTER.
2
DATE START
END
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
CH
– –
– –
– –
– –
– –
– –
– –
– –
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
–
–
–
–
–
–
–
–
OTR 0 : 30
CH 125
Press REC on the VCR or while
Press SET –/+ to select the
date, then press ENTER.
3
4
holding REC, press PLAY ( ) on
the Remote to begin recording.
Press REC on the VCR again to
stop recording after 30 minutes.
Each additional press of REC will
increase recording time as shown
in the chart below, up to a
maximum of 5 hours. The OTR
and recording time will appear on
screen for about 4 seconds.
⟨
+ –
⟩
/
/ENTER/CANCEL/MENU
Set the start time, end time,
channel and tape speed as in
step 3.
DATE
START END
CH
---
26(SU)
-
-:-- -:--
------ -:-- -:-- ---
------ -:-- -:-- ---
------ -:-- -:-- ---
------ -:-- -:-- ---
------ -:-- -:-- ---
------ -:-- -:-- ---
------ -:-- -:-- ---
-
-
-
-
-
-
-
NOTE: To record from external
source, press SET –/+
and set the channel to
"L". "L" will appear
+
⟨
/–/ENTER/CANCEL/MENU⟩
next to CH 125 (or 69).
NOTES: • Press REC to increase
the time needed for
recording (See the
Press Recording time
once
twice
NORMAL REC
To enter other programs,
repeat step 2 through 4. Or,
press MENU twice to return
to the normal screen.
5
6
0:30
chart ).
• To cancel OTR, press
STOP ( ) or turn off
the power.
3 times
4 times
5 times
6 times
7 times
8 times
1:00
1:30
2:00
3:00
4:00
5:00
Press TIMER on the Remote.
The power will go off, the
TIMER indicator will light and
the VCR stands by for
recording.
9 times NORMAL REC
Watching one program while recording another
During recording…
• If you connect the TV and the VCR only using the RF
connection to view pictures from the VCR, press TV/VCR
on the Remote so that VCR indicator goes off. (The TV
broadcast being recorded disappears.)
To use the VCR while it is in timer recording standby mode
Press TIMER. After you use the VCR, press TIMER again
to put the VCR into timer recording standby mode.
• If you are using the AV connection to view pictures from
the VCR, change the TV’s input mode from AV to TV.
Then, select the channel you want to watch, on the TV.
– Timer Recordings –
IF THE PROGRAM OVERLAPS ANOTHER
TO CORRECT THE SETTINGS
When setting the Timer Recording, press ENTER until the
desired setting blinks, then re-enter the setting using SET –/+.
When finished, press ENTER.
NOTE: Do not overlap programs as portions of the
conflicting programs will be lost. The first
recording time has priority over the next recording
time as shown in the diagram.
NOTES: • The VCR cannot be used while the TIMER
indicator is lit.
8 : 00
9 : 00
10 : 00
11 : 00
• After a power failure or disconnection of the
power plug, all programmed recording settings
must be reset upon resumption of power. In this
case, reset the clock and reprogram any timer
recordings.
• Press CANCEL to move cursor backward for
correction.
Program 1
Program 2
Deleted Parts
Program 3
Non Recorded Portion Parts
Recording
Control Settings
Prog.1
Prog.2
Prog.3
NOTES: • The everyday/every week recording can be made
continuously until the recording is canceled or
the tape reaches the end.
TO SET DAILY/WEEKLY TIMER
When setting the date in step 3 in the Setting the Timer
Recording section on the previous page, press SET –
repeatedly.
• During timer recording, the automatic rewinding
mechanism does not function.
The setting changes as follows:
Example
The current day (Friday)
SU-SA (Sunday to Saturday)
MO-SA (Monday to Saturday)
MO-FR (Monday to Friday)
WKL-TH (Weekly Thursday)
One month later
minus one day
WKL-WE
(Weekly Wednesday)
TO CONFIRM THE SETTINGS
Press SET –/+ to select the
DATE START
END
CH
(
)
26 WE 11:00PM 11:30PM 125 EP
“TIMER REC SET” option in the
– – – – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– –
– –
– –
– –
– –
– –
– –
–
–
–
–
–
–
–
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
MENU. Then press ENTER to
display the timer program list.
Press MENU twice to return to
the normal screen.
⟨
+ –
⟩
/
/ENTER/CANCEL/MENU
TO CANCEL A PROGRAM
Press the SET –/+ to select the
“TIMER REC SET” option in the
MENU. Then press SET –/+ to
select the unnecessary program,
and press CANCEL to cancel the
program.
DATE START
END
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
CH
– –
– –
– –
– –
– –
– –
– –
– –
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
– : – –
–
–
–
–
–
–
–
–
⟨
+ –
⟩
/
/ENTER/CANCEL/MENU
Other Functions
BLUE BACK — ON/OFF
SEPARATE AUDIO PROGRAM (SAP)
Your VCR is fitted with an SAP broadcast system which
enables you to switch to a SEPARATE AUDIO PROGRAM
when viewing a selected channel.
This function applies only when the program is
broadcast in multi-languages through the SAP broadcast
system.
When this function is set to “ON”, the TV screen becomes all
blue in the following cases:
When receiving a channel not in use.
When stopping playback.
1
Press MENU on the remote. Press SET –/+ to select
“NO NOISE BACKGROUND”.
2 Press ENTER to select “ON”.
When a TV is connected with an audio/video cable, turn the
TV and this VCR on, and select the video input mode the TV.
Press MENU to return to normal screen.
3
MENU
CLOCK SET
Press MENU.
STEREO RECORDING AND PLAYBACK
TIMER REC SET
1
AUTO REPEAT
CH SET UP
SAP
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
ON OFF
ON OFF
Press on the Remote SET –/+ to
RECORDING STEREO BROADCASTS
select “SAP” option.
The VHS Hi-Fi audio system permits high fidelity recording
of MTS STEREO TV broadcasts.
ON OFF
⟨+/–/ENTER/MENU⟩
Press ENTER to select “ON”
position.
2
3
When a MTS STEREO broadcast is
STEREO
received, the STEREO will appear on
the screen and the program can be
viewed or recorded in stereo.
The Hi-Fi STEREO recording proce-
dure is the same as for normal
recordings.
MENU
CLOCK SET
TIMER REC SET
AUTO REPEAT
CH SET UP
SAP
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
Press MENU to return to
normal screen.
ON OFF
ON OFF
ON OFF
⟨+/–/ENTER/MENU⟩
NOTE: When using a CATV system, stereo TV programs
may be transmitted over a mono cable channel. In
this case the word "STEREO" will not appear and the
sound will be in mono.
LISTENING TO SAP
When the VCR is turned on or a channel selection is made,
make certain "SAP" appears on the screen.
This means that the "Separate Audio Program" broadcast-
ing is available.
OUTPUT SELECTION
When viewing an MTS STEREO TV program, or playing a
prerecorded VHS Hi-Fi STEREO videotape, press
A.MONITOR to select how the audio will be heard through
the speakers. Normally set to the Hi-Fi STEREO position, this
button can be set to the MONO position if the stereo
broadcast or videotape audio is of poor quality. The "R" and
"L" positions allow the audio from the Right or Left Hi-Fi
channel to be heard over both TV speakers. This button has
no effect when viewing a MONO videotape or TV program.
Each time when you press the button, OUTPUT SELECTION
display appears on the screen for several seconds. Refer to
the chart below.
STEREO SAP
SAP
OR
OUTPUT
SELECTION
SOUND HEARD ON BOTH
SPEAKERS
JVC TV Remote Control
This Remote can control some functions (TV POWER,
INPUT, TV CH –/+ and TV VOL –/+) of a remote
controllable JVC TV without setting.
STEREO
L ch
R ch
STEREO
LEFT CHANNEL AUDIO
RIGHT CHANNEL AUDIO
MONO
NOTE:
MONO
• It’s not possible to operate a unit not equipped with a
remote sensor.
NOTES: • When playing back a tape that is not recorded in
Hi-Fi stereo mode, the audio will automatically be
monaural.
• This Remote can control a JVC TV only.
• When listening to a VHS Hi-Fi video tape or MTS
broadcast through the VHF/UHF jack (Audio/
Video cord not connected), the sound will be
monaural.
Editing
You can use your VCR as the playback or recording VCR.
You can use a camcorder as the playback VCR and your VCR
as the recording VCR. Refer also to the other components’
instruction manuals for connection and its operations.
1
Make connections
Example: When using this VCR as the playback VCR
This VCR (for playback)
To audio/video out
Audio/video cable (not
supplied)
To audio/video input
Another VCR (for recording)
• When using this VCR as the recording VCR, connect this
VCR’s audio/video input connectors to the audio/video
output connectors on the other VCR. If the playback VCR
is monaural, connect the audio output connector on the
playback VCR to the left audio input connector on this
VCR.
2 Load cassettes
Insert the playback cassette into the playback VCR and the
cassette to be recorded on into the recording VCR.
3
Select input mode on recording VCR
Select the correct external input on the recording VCR.
On this VCR (when using this VCR as the recording VCR);
Select “L” — when connecting the other VCR to the audio/video
input connectors on the front panel.
Press O (AUX) or CH–/+ on the Remote [CH–/+ on the VCR].
4
Start playback
Press PLAY ( ) on the playback VCR.
5
Start recording
Press REC on the recording VCR.
Before Requesting Service
Make sure by first checking the following points.
SYMPTOM
POWER
CAUSE
POSSIBLE SOLUTION
Connect the AC power cord to the AC
outlet.
Insert a video cassette.
The AC power cord is not connected.
Cassette is not inserted.
No power.
Although the power is on, it
does not operate.
TV BROADCAST RECEPTION
Antenna connection is not correct.
Antenna cable is disconnected.
The video channel is not in the correct
position.
Connect it correctly.
Reconnect the antenna cable.
Set it to CH 3 or 4.
A TV program that is selected by
the VCR does not appear on the
screen.
The TV is not set to the video channel
3 or 4.
Set the TV channel selector to the 3 or 4
position.
The TV/VCR selector is set at TV mode
(The TV/VCR indicator is not lit).
Press the TV/VCR selector button (The TV/
VCR indicator will light).
INPUT is set to the LINE mode.
Press the Number key or CH –/+ button to
select your desired TV program.
The TV/CATV menu option setting.
A TV program selected by the
VCR does not appear in color.
Set the TV/CATV menu option to select TV
or CATV mode.
RECORDING
Place a piece of vinyl tape over the gap.
The erase prevention tab of the video
cassette is broken off.
TV recording does not work.
Press the Number key or CH –/+ button to
select your desired TV program.
INPUT is set to the LINE mode.
Reset the present time.
The time is not set correctly.
The recording start/end time is not set
correctly.
Set the start/end time.
Timer recording does not work.
Press the TIMER button (The TIMER
indicator is lit).
The TIMER button has not been
pressed (The TIMER indicator is not lit).
PLAYBACK
No picture on screen when
playing back a recorded tape.
The TV is not set to the video channel 3
or 4.
Set to the video channel 3 or 4 or
adjust the fine tuning button on your
TV set.
Tracking adjustment beyond range of
automatic tracking circuit.
Video heads are dirty.
Adjust tracking manually using the SET – or
+ buttons on the remote control.
Noise bars on screen.
Have the video heads cleaned.
Try another tape.
The tape is worn or damaged.
REMOTE CONTROL
It is not aimed at the remote sensor.
Aim it at the remote sensor.
Distance too far or too much light in
the room.
Operate within 15 feet (5 meters) reduce
the light in the room.
There is an obstacle in the path of the
beam.
Clear the path of the beam.
Remote control does not work.
The batteries are weak.
The +, – polarity of the batteries are
not inserted correctly.
Replace the batteries.
Insert correctly.
TV programs cannot be seen
using the TV selector.
Set to TV, or turn off the VCR power
button.
The TV/VCR function is in the VCR
mode.
Specifications
GENERAL
:
AC 120 V, 60 Hz
Power requirement
Power consumption
Power on
:
:
9 W
1.7 W
Power off
Temperature
Operating
:
:
:
:
:
:
5°C to 40°C (41°F to 104°F)
–20°C to 60°C (–4°F to140°F)
Horizontal only
360 mm x 95 mm x 224 mm (14-3/16" x 3-3/4" x 8-13/16")
3.2 kg (7.1 lbs)
VHS NTSC standard
Storage
Operating position
Dimensions (W x H x D)
Weight
Format
Maximum recording time
SP
:
:
210 min. with ST-210 video cassette
630 min. with ST-210 video cassette
EP
VIDEO/AUDIO
:
NTSC-type color signal and EIA monochrome signal, 525 lines/60 fields
Signal system
Recording/Playback
system
:
:
:
DA-4 (Double Azimuth) head helical scan system
42 dB
230 lines
Signal-to-noise ratio
Horizontal resolution
Frequency range
Normal audio
Hi-Fi audio
:
:
:
100 Hz to 10,000 Hz
20 Hz to 20,000 Hz
RCA connectors (IN x 1, OUT x 1)
Input/Output
TUNER
:
Frequency-synthesized tuner
Tuning system
Channel coverage
VHF
:
:
:
:
Channels 2–13
Channels 14–69
UHF
113 Channels
CATV
RF output
Channel 3 or 4 (switchable; preset to Channel 3 when shipped) 75 ohms,
unbalanced
TIMER
:
:
:
Quartz
Clock reference
1-month programmable timer/8 programs
Approx. 5 sec.
Program capacity
Memory backup for timer
ACCESSORIES
:
RF cable (F-type), Infrared remote control unit, “AAA” battery x 2
Provided accessories
Specifications shown are for SP mode unless specified otherwise.
E. & O.E. Design and specifications subject to change without notice.
FOR SERVICING (Only in U.S.A.)
HOW TO LOCATE YOUR JVC SERVICE CENTER
TOLL FREE: 1-800-537-5722
Dear Customer,
In order to receive the most satisfaction from your purchase, please read the instruction booklet before operating the unit. In the
event that repair is necessary, or for the address nearest your location within the Continental United States, please call 1-800-
Warranty Service.
— JVC
JVC SERVICE & ENGINEERING
COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.
Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering and
production of the wide array of JVC products, service is the key to maintaining the high level performance for which JVC is
world famous. The JVC service and engineering organization stands behind our products.
NATIONAL HEADQUARTERS
JVC SERVICE & ENGINEERING COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.
10 New Maple Avenue
Pine Brook, NJ 07058-9641
Don’t service the product yourself.
ACCESSORIES
To purchase accessories for your JVC product, you may
contact your local JVC Dealer.
From the 48 Continental United States call toll free:
CAUTION
To prevent electrical shock, do not open the cabinet. There
are no user serviceable parts inside.
Please refer to qualified service personnel for repairs.
WARRANTY (Only in U.S.A.)
LIMITED WARRANTY
CONSUMER VIDEO 1-90
JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINAL
PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original retail purchase
for the period as shown below. (“The Warranty Period”)
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND IN COMMON-
WEALTH OF PUERTO RICO.
WHAT WE WILL DO:
If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner. Such repair and
replacement services shall be rendered by JVC during normal business hours at JVC authorized service centers. Parts used for
replacement are warranted only for the remainder of the Warranty Period. All products and parts thereof may be brought to a JVC
authorized service center on a carry-in basis except for Television sets having a screen size 25 inches and above which are covered
on an in-home basis.
WHAT YOU MUST DO FOR WARRANTY SERVICE:
Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized service
center, please call toll free: (800) 537-5722.
If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy of your bill
of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center, the name and location of which will be
given to you by the toll-free number.
If you have any questions concerning your JVC Product, please contact our Customer Relations Department.
WHAT IS NOT COVERED:
This limited warranty provided by JVC does not cover:
1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation,
lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by JVC to render such service,
or if affixed to any attachment not provided with the products, or if the model or serial number has been altered, tampered with,
defaced or removed;
2. Initial installation and installation and removal for repair;
3. Operational adjustments covered in the Owner’s Manual, normal maintenance, video and audio head cleaning;
4. Damage that occurs in shipment, due to act of God, and cosmetic damage;
5. Signal reception problems and failures due to line power surge;
6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of purchase;
7. Accessories;
8. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase);
There are no other express warranties except as listed above.
THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS LIMITED TO
THE DURATION OF THE EXPRESS WARRANTY HEREIN.
JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHER DAMAGES,
WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE TO TAPES, RECORDS OR
DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. ALL EXPRESS
AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE,
ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied warranty lasts,
so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other
rights which vary from state to state.
JVC COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.
1700 Valley Road
Wayne, New Jersey 07470
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR DETAILS OF REFUR-
BISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION PACKAGED
WITH EACH REFURBISHED PRODUCT.
For customer use:
Enter below the Model No. and Serial No. which is located either on the rear, bottom or side of the cabinet. Retain this
information for future reference.
Model No.:
Serial No.:
Purchase date:
Name of dealer:
|