®
Shielded Indoor/Outdoor
Monitor Speaker
Control 25AV
Professional Series
Key Features:
᭤
Video shielded for use near video
monitors.
᭤
᭤
Extremely smooth frequency response.
Stainless steel grille for harsh
environments.
᭤
60 Watt transformer for 70V or 100V
lines, with 8⍀ thru.
TM
᭤
᭤
SonicGuard overload protection.
130 mm (5¼") polypropylene coated
woofer, 10 mm (¾") titanium coated
horn-loaded tweeter.
᭤
Includes InvisiBall® mounting
hardware and sealed input panel cover.
᭤
᭤
Screw-down input terminals.
100° x 100° high frequency horn.
®
The Control 25AV utilizes a deep
cabinet, high power components and
complex network to achieve extremely
smooth high fidelity performance from a
compact 2-way loudspeaker.
Premium performance capability and
even coverage ensures excellent sound
quality throughout the listening area.
Specifications:
1
Freq. Range (-10 dB) : 70 Hz - 23 kHz
2
Midrange ( 1.5 dB, typical) : 130 Hz - 14 kHz
3
100 Hr Power Capacity : 200 Watts Continuous Program Power
100 Watts Continuous Pink Noise
Nominal Coverage: 100° x 100°
Nominal Sensitivity : 87 dB SPL, 1W @ 1 m (3.3ft)
Nominal Coverage: 100° x 100°
4
Maximum SPL @ 1m: 113 dB continuous peak pink noise
107 dB continuous average pink noise
Magnetic shielding allows use of the
speaker in close proximity to video moni-
tors.
The top-quality transformer, with
reduced saturation, allows use on either
70 volt or 100 volt distributed speaker
lines, with similar performance fidelity. In
the bypass position, the high 8⍀ imped-
ance allows use of more speakers on a
loudspeaker line.
103 dB continuous average music or speech
Directivity Factor (Q): 4.9, averaged 500 Hz to 4 kHz
Directivity Index (DI): 6.9 dB, averaged 500 Hz to 4 kHz
Nominal Impedance: 8 ohms
Minimum Impedance: 6.7 ohms at 230 Hz
Crossover Type: Second Order Lowpass, Second Order Highpass, Complex
Optimization for Maximally Flat Response
Transformer Taps: 170V: 60W, 30W, 15W, 7.5W taps (Taps #4,#3, #2 & #1)
100V: 60W, 30W, 15W taps (Taps #3, #2, & #1)
Thru position: 8⍀ nominal
Transducers:
Physical:
Low-Frequency: 130 mm (5.25 in) polypropylene-coated paper with WeatherEdge
surround, 25 mm (1 in) voicecoil on kapton former
High-Frequency: 20 mm (.75 in) titanium coated PEI
The unique, global patent pending
®
InvisiBall mounting method is simple to
install, aims easily, and provides a high
degree of theft deterrence.
Enclosure Material: High Impact polystyrene
Grille: Painted stainless steel, black or white to match cabinet, paintable
Overload Protection: Full-range power limiting to protect network and transducers. Internal
fuse to protect during exceptional overload condition
The cabinet accepts a variety of paints
to match any décor.
Weather resistance is maximized by a
stainless steel grille, which is paintable.
Coating the woofer in polypropylene and
terminating its circumference in JBL’s
WeatherEdgeTM, a seamless, butyl rubber
extension of the woofer surround, pro-
tects critical transducer elements. The
polycarbonate tweeter diaphragm is rein-
forced with a thin film of titanium for
added rigidity and endurance. Nickel/zinc
rust-resistant terminals ensure a secure
input connection.
JBL’s exclusive SonicGuard overload
protection is virtually inaudible to the lis-
tener, ensuring reliability while providing
full fidelity sound.
The Control 25AV can be used full
range or low frequencies can be further
augmented with the addition of one of
the Control Contractor subwoofer models.
Environmental: Exceeds Mil Spec 810 for humidity, salt spray, temperature & UV. IEC
529 IP-X4 splashproof rating
Termination: Screw-down terminal strip, zinc-plated copper base, nickel plated
metal screws/washers, accepts up to 9 mm outside 4 mm inside open
lug (#6, #8 or #10), plus bare wire. (up to 12 AWG)
Safety Agency Rating: Transformer is listed per UL1876
Colors: Black or white (-WH)
Rotation: Against wall on InvisiBall Base: 37° vertical 44° horizontal
On bracket: 44° all directions
Dimensions (H x W x D): 236 x 186 x 159 mm (9.3 x 7.4 x 6.3 in)
Net Weight (ea): 4.0 kg (9 lbs)
Shipping Weight (pair): 9.0 kg (20 lbs) per pair
Included Accessories: 1 Pr MTC-PC input panel cover, InvisiBall mounting base, 6 mm x 100
mm InvisiBall hex wrench
Optional Accessories: MTC-25V for vertical columnar mounting of up to 3 speakers
MTC-25/23H for horizontal splaying of 2 speakers. Three brackets
array either 3 or 6 speakers in a hanging array module for 360°
horizontal coverage.
MTC-28/25CM to install speaker down from the ceiling.
Check JBL Control Contractor Bracket and Adapter Handbook.
MTC-xxWMG WeatherMax™ Stainless Steel Grille with a three-layer
backing, including vapor barrier to break up driving precipitation.
Available in black or white (-WH).
1
2
In half-space (on wall).
In full-space
3
Continuous Pink Noise rating is IEC-shaped pink noise with a 6 dB crest factor for 100 hours continuously.
Continuous program power is a conservative expression of the system’s ability to handle normal speech and music
program material and is defined as 3 dB above the Continuous Pink Noise Rating.
4
Half-space (on wall) averaged 100 Hz to 10 kHz.
Available in black or white (-WH)
JBL continually engages in research related to product improvement. Changes introduced into existing products with-
out notice are an expression of that philosophy.
Horizontal 1/3 Octave Polars
Architectural Specifications:
The loudspeaker shall consist of a 135 mm (5-1/4 in) low frequency
transducer, 20 mm (3/4 in) high frequency transducer, and frequency
dividing network installed in ported enclosure. The low frequency voice
coil shall be 25 mm (1 in) in diameter.
Performance specifications of a typical unit shall be as follows: Usable
frequency response shall extend from 70 Hz to 23 kHz (10 dB below
rated sensitivity, in half-space, with no external equalization) and the
speaker shall be flat from 130 Hz to 14 kHz (typically 1.5 dB). Rated
power shall be at least 200 watts continuous program power for 100
continuous hours duration (defined a 3 dB above a test signal of filtered
random pink noise conforming to international standard IEC268-5).
Measured sensitivity shall be at least 87 dB-SPL (at 1m [3.3ft] with 2.83V
input, averaged from 100 Hz to 10 kHz).
The input shall be switchable for use either at nominal 8 ohms, or on
a 70.7V or 100V distributed speaker line via a built-in 60W transformer.
Selectable taps shall allow operation nominally at 15W, 30W or 60W
from either a 70.7V or 100V distributed speaker line, plus 7.5W from a
70.7V line only.
The system shall be protected against damage from occasional over-
powering via full range limiting that limits the power to the network and
transducers. The limiting system shall be inaudible during activation. The
high frequency transducer shall be horn-loaded to more evenly cover a
nominal 90° horizontal by 90° vertical area.
The enclosure shall be constructed of high-impact polystyrene and the
grille shall be made of treated stainless steel for protection against the
elements in outdoor applications, and for easy paintability of both cabi-
net and grille. The grille shall be secured via screws to keep it in place
when facing downward.
The low frequency transducer shall have a polypropylene-coated cone
and a butyl rubber surround which shall extend seamlessly over the
edge of the speaker frame to protect against the elements. The high fre-
quency transducer shall be constructed of polycarbonate, reinforced with
a titanium film for additional weather resistance. The system shall with-
stand Mil Spec 810 testing with specified durations for exposure to the
following environments with no effect on its acoustical performance or
structural integrity: salt spray (method 509.3), temperature (method 501.3
and 502.3), humidity (method 507.3) and ultra-violet (method 505.3).
The system shall have an IEC 529 splashproof rating of IP-X4.
For theft deterrence, the installation access area shall be hidden
behind a snap-out cover, and the access area shall be on the front of the
loudspeaker for ease of installation and adjustment. The loudspeaker
shall be rotatable over a minimum of 35° in all directions via a ball-
type mounting system. The ball mechanism shall be internal to the cabi-
net to allow low-profile mounting and better stability via short moment
arm. The logo shall be rotatable for proper orientation when the loud-
speaker is mounted horizontally or vertically.
The external wiring connectors shall be screw-down terminals. Overall
cabinet dimensions shall be no greater than 236 high x 186 wide x 159
mm deep (9.3 x 7.4 x 6.3 in). and shall weigh no more than 4.0 kg (9
lb). The finish shall be lightly textured black or white.
The system shall be the JBL Model Control 25AV (or Control 25AV-
TM
WH) with included InvisiBall mounting system.
®
᭤ Control 25AV
Vertical 1/3 Octave Polars
JBL Professional
8500 Balboa Boulevard, P.O. Box 2200
Northridge, California 91329 U.S.A.
A Harman International Company
SS Control 25AV
CRP 15M
11/01
|