PE10X-X-X-A0S
OPERATOR’S MANUAL
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
RELEASED: 9-15-04
REVISED:
(REV.06)
11-13
-10
1” DIAPHRAGM PUMP
1:1 RATIO (METALLIC)
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
SERVICE KITS
Refer to Model Description Chart to match the pump material options.
637401-XXforfluidsectionrepair(seepage4).NOTE:Thiskitalsocon-
tains several air motor seals which will need to be replaced.
637412 for air section repair (see page 6).
PUMP DATA
Models . . . . . . . . . . . . . see Model Description Chart for “-XXX”.
Pump Type . . . . . . . . . . MetallicAirOperatedDoubleDiaphragm
Material . . . . . . . . . . . . . see Model Description Chart.
Weight . . . PE10R-XAX-XXX-A0S . . . 17.87 lbs (8.11 kgs)
PE10R-XCX-XXX-A0S . . . 34.77 lbs (15.77 kgs)
PE10R-XHX-XXX-A0S . . . 39.17 lbs (17.77 kgs)
PE10R-XSX-XXX-A0S . . . 37.77 lbs (17.13 kgs)
Figure 1
add 5.26 lbs (2.39 kg) for Aluminum air motor section
add 11.43 lbs (5.18 kg) for Stainless Steel air motor section
MODEL DESCRIPTION CHART
Maximum Air Inlet Pressure . . . . . . . . . 120 p.s.i.g. (8.3 bar)
Maximum Material Inlet Pressure . . . . . 10 p.s.i.g. (0.69 bar)
Maximum Outlet Pressure . . . . . . . . . . 120 p.s.i.g. (8.3 bar)
Maximum Flow Rate (flooded inlet) . . . . 52.2 g.p.m. (197.6 l.p.m.)
Displacement / Cycle @ 100 p.s.i.g. . . . 0.232 gal. (0.88 lit.)
Maximum Particle Size . . . . . . . . . . . . 1/8” dia. (3.3 mm)
Maximum Temperature Limits (diaphragm / ball / seal material)
E.P.R. / EPDM . . . . . . . . . . . -60_to280_F (-51_to 138_C)
HytrelR . . . . . . . . . . . . . . . -20_ to 150_ F (-29_ to 66_ C)
Nitrile . . . . . . . . . . . . . . . . . 10_ to 180_ F (-12_ to 82_ C)
Polypropylene . . . . . . . . . . . 35_ to 175_ F (2_to79_ C)
SantopreneR . . . . . . . . . . . -40_to225_F (-40_to 107_C)
PTFE . . . . . . . . . . . . . . . . . 40_ to 225_ F (4_ to 107_ C)
VitonR . . . . . . . . . . . . . . . . -40_to350_F (-40_to 177_C)
Dimensional Data . . . . . . . . . . . . . . . . see page 8
PE10 X - X X X - X X X - A0S
Center Section Material
A - Aluminum
R - Polypropylene
S - Stainless Steel
Fluid Connection
A - 1 - 11-1/2 N.P.T.F. - 1
B - 1 - 11 BSP
Fluid Caps & Manifold Material
A - Aluminum
C - Cast Iron
Hardware Material
P - Plated Steel
S - Stainless Steel
H - Hastelloy - C
S - Stainless Steel
Mounting Dimension . . . . . . . . 4”x6.25”(101.6mmx158.8mm)
Noise Level @ 70 p.s.i., 60 c.p.m. . . . . . 80.6 db(A){
Seat Material
A - Santoprene
C - Hytrel
E - Carbon Steel
F - Aluminum
G - Nitrile
H - Hard 440 Stainless Steel
L - Hastelloy - C
S - 316 Stainless Steel
The pump sound pressure levels published here have been updated to an Equivalent
Continuous Sound Level (L ) to meet the intent of ANSI S1.13-1971, CAGI-PNEU-
Aeq
ROP S5.1 using four microphone locations.
Ball Material
A - Santoprene
C - Hytrel
NOTICE: All possible options are shown in the chart, however, certain
combinations may not be recommended, consult a representative or the
factory if you have questions concerning availability.
S - 316 Stainless Steel
T - PTFE
V - Viton
G - Nitrile
Diaphragm Material
A - Santoprene
C - Hytrel
M - Medical Grade Santoprene
T - / Santoprene
V - Viton
G - Nitrile
FLUID SECTION SERVICE KIT SELECTION
PE10X - XXX - X X X - A0S
637401 - X X
EXAMPLE: Model # PE10A-ASP-AAA-A0S
Fluid Section Service Kit # 637401-AA
Ball
Diaphragm
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET -- BRYAN, OHIO 43506
(800) 276-4658 D FAX (800) 266-7016
E2010
CCN 15214133
GENERAL DESCRIPTION
OPERATING INSTRUCTIONS
The ARO diaphragm pump offers high volume delivery even at low air
pressure and a broad range of material compatibility options available.
Refer to the model and option chart. ARO pumps feature stall resistant
design, modular air motor / fluid sections.
Air operated double diaphragm pumps utilize a pressure differential in
theairchamberstoalternatelycreatesuctionandpositivefluidpressure
in the fluid chambers, ball checks insure a positive flow of fluid.
Pump cycling will begin as air pressure is applied and it will continue to
pump and keep up with the demand. It will build and maintain line pres-
sure and will stop cycling once maximum line pressure is reached (dis-
pensing device closed) and will resume pumping as needed.
S Always flush the pump with a solvent compatible with the material
being pumped ifthe materialbeing pumpedissubjectto “settingup”
when not in use for a period of time.
S Disconnecttheairsupplyfromthepumpifitistobeinactiveforafew
hours.
PARTS AND SERVICE KITS
Refertothepartviewsanddescriptionsasprovidedonpage4through7
for parts identification and Service Kit information.
S Certain ARO “Smart Parts” are indicated which should be available
for fast repair and reduction of down time.
S Service kits are divided to service two separate diaphragm pump
functions: 1. AIR SECTION, 2. FLUID SECTION. The FLUID SEC-
TION is divided further to match typical part MATERIAL OPTIONS.
AIR AND LUBE REQUIREMENTS
WARNING EXCESSIVE AIR PRESSURE. Can cause pump
damage, personal injury or property damage.
S Afiltercapableoffilteringoutparticleslargerthan50micronsshould
beusedontheairsupply. Thereisnolubricationrequiredotherthan
the “O” ring lubricant which is applied during assembly or repair.
S Iflubricatedairispresent,makesurethatitiscompatiblewiththe“O”
rings and seals in the air motor section of the pump.
MAINTENANCE
S Provide a clean work surface to protect sensitive internal moving
partsfrom contaminationfrom dirtand foreignmatter duringservice
disassembly and reassembly.
S Keep good records of service activity and include pump in preven-
tive maintenance program.
S Before disassembling, empty captured material in the outlet man-
ifold by turning the pump upside down to drain material from the
pump.
INSTALLATION
S Verify correct model / configuration prior to installation.
S Retorque all external fasteners per specifications prior to start up.
S Pumpsaretestedinwateratassembly. Flushpumpwithcompatible
fluid prior to installation.
FLUID SECTION DISASSEMBLY
S When the diaphragm pump is used in a forced-feed (flooded inlet)
situation, it is recommended that a “Check Valve” be installed at the
air inlet.
1. Remove (61) outlet manifold, (60) inlet manifold.
2. Remove (22) balls, (19 and 33) “O” rings (if applicable) and (21)
seats.
S Material supply tubing should be at least the same diameter as the
pump inlet manifold connection.
3. Remove (15) fluid caps.
S Material supply hose must be reinforced, non-collapsible type com-
patible with the material being pumped.
NOTE: Only PTFE diaphragm models use a primary diaphragm (7) and
a backup diaphragm (8). Refer to the auxiliary view in the Fluid Section
illustration.
S Piping must be adequately supported. Do not use the pump to sup-
port the piping.
4. Remove the (14) screw, (6) diaphragm washer, (7) or (7 / 8) dia-
phragms, and (5) backup washer.
NOTE: Do not scratch or mar the surface of (1) diaphragm rod.
S Use flexible connections (such as hose) at the suction and dis-
charge. These connections should not be rigid piped and must be
compatible with the material being pumped.
S Secure the diaphragm pump legs to a suitable surface (level and
flat) to insure against damage by vibration.
FLUID SECTION REASSEMBLY
S Pumpsthat needto be submersed must have bothwet and non-wet
components compatible with the material being pumped.
S Submersed pumps must have exhaust pipe above liquid level. Ex-
haust hose must be conductive and grounded.
S Flooded suction inlet pressure must not exceed 10 p.s.i.g. (0.69
bar).
S Reassemble in reverse order. Refer to the torque requirements on
page 5.
S Clean and inspect all parts. Replace worn or damaged parts with
new parts as required.
S Lubricate (1) diaphragm rod and (144) “U” cup with LubriplateR
FML-2 grease (94276 grease packet is included in service kit).
S FormodelswithPTFEdiaphragms:Item(8)Santoprenediaphragm
is installed with the side marked “AIR SIDE” towards the pump cen-
ter body. Install the PTFE diaphragm (7) with the side marked
“FLUID SIDE” towards the (15) fluid cap.
S Re-check torque settings after pump has been re-started and run a
while.
S VitonR and HytrelR are trademarks of the DuPont Company S KynarR is a registered trademark of Penwalt Corp. S LoctiteR is a registered trademark of Henkel Loctite Corporation S
S SantopreneR is a registered trademark of Monsanto Company, licensed to Advanced Elastomer Systems, L.P. S LubriplateR is a registered trademark of Lubriplate Division (Fiske Brothers) S
PE10X-X-X-A0S
Page 3 of 8
PARTS LIST / PE10X-X-X-A0S FLUID SECTION
L 637401-XX FLUID SECTION SERVICE KITS INCLUDE: BALLS (see Ball Option, refer to -XX in Service Kit chart below), DIAPHRAGMS (see Diaphragm
Option, refer to -XX in Service Kit chart below), and items 19, 70, 144, 175 and 180 (listed below) plus 94276 Lubriplate FML-2 grease (page 6).
SEAT OPTIONS PE10X-XXX-XXX-A0S
BALL OPTIONS PE10X-XXX-XXX-A0S
“21”
L “22” (1-1/4” dia.)
-XXX Seat
Qty [Mtl]
(4) [SP]
-XXX Seat
Qty [Mtl]
(4) [B]
(4) [SH]
(4) [Ha]
(4) [SS]
-XXX Ball
Qty [Mtl]
(4) [SP]
-XXX Ball
Qty [Mtl]
(4) [SS]
-AXX 96152-A
-CXX 96152-C
-EXX 96158
-FXX 96156
-GXX 96152-G
-HXX 94706
-LXX 95836
-SXX 96151
-XAX 93278-A
-XCX 93278-C
-XGX 93278-2
-XSX 92408
-XTX 93278-4
-XVX 93278-3
(4)
(4)
(4)
[H]
[C]
[A]
(4)
(4)
[H]
[B]
(4)
(4)
[T]
[V]
DIAPHRAGM OPTIONS PE10X-XXX-XXX-A0S
L Service Kit
-XX = (Ball)
-XXX -XX = (Diaphragm) Diaphragm Qty [Mtl] Diaphragm Qty [Mtl] Gasket
L “7”
L “8”
L “19” (1/8” x 2-1/8” o.d.)
L “33” (1/8” x 1-5/8” o.d.)
Qty [Mtl] Gasket
Qty [Mtl]
-XXA 637401-XA
-XXC 637401-XC
-XXG 637401-XG
-XXM 637401-XM
-XXT 637401-XT
-XXV 637401-XV
96267-A
96267-C
96267-G
96267-M
96146-T
95989-3
(2)
(2)
(2)
[SP] - - - - -
- - -
- - -
- - -
- - -
- - - 93280
(4)
(4)
(4)
(4)
(4)
(4)
[E] 93279
(4)
(4)
(4)
(4)
(4)
(4)
[E]
[V]
[B]
[T]
[T]
[V]
[H]
[B]
- - - - -
- - - - -
- - - Y327-225
- - - Y325-225
- - - 93282
[V] Y327-220
[B] Y325-220
[T] 93281
[T] 93281
[V] Y327-220
(2) [MSP] - - - - -
(2)
(2)
[T]
[V]
96145-A
- - - - -
(2) [SP] 93282
- - - - - - Y327-225
NOTE: Gasket items 19 and 33 are not required with seat options -AXX, -CXX and -GXX.
CENTER SECTION OPTIONS PE10X-XXX-XXX-A0S
MATERIAL CODE
[A] = Aluminum
[B] = Nitrile
[C] = Carbon Steel
[CI] = Cast Iron
[Co] = Copper
PE10A-X-X-A0S
PE10R-X-X-A0S
PE10S-X-X-A0S
Item Description (size)
28 Washer (8.5 mm i.d.)
43 Ground Lug (see page 7)
68 Air Cap
Qty Part No.
[Mtl] Part No.
- - - 96217
[Co] - - - - -
[A] 96104-3
[A] 96104-4
[SS] 93832-3
[C] - - - - -
- - - 96216
[Co] - - - - -
- - - 96292
[SS] 95879
[Mtl] Part No.
[Mtl]
- - -
(4) - - - - -
(1) 93004
(1) 95994-4
(1) 95994-3
(2) Y17-51-S
(4) 96001
(4) - - - - -
(4) 96006
(8) - - - - -
(4) 96005
[SS] - - - - -
- - - 93004
[P] 96007-3
[P] 96007-4
[K] Y17-51-S
- - - 96001
[SS] - - - - -
- - - 96006
[B] - - - - -
[SS] 96005
[E] = E.P.R.
[H] = Hytrel
[Co]
[SS]
[SS]
[SS]
[C]
[Ha] = Hastelloy-C
[K] = PVDF (KynarR)
[MSP]=MedicalGradeSantoprene
[P] = Polypropylene
[SH] = Hard Stainless Steel
[SP] = Santoprene
[SS] = Stainless Steel
[T] = PTFE
[V] = Viton
69 Air Cap
74 Pipe Plug (1/4 - 18 N.P.T. x 7/16”)
131 Screw (M8 x 1.25 - 6g x 95 mm)
(M8 x 1.25 - 6g x 100 mm)
- - -
[Co]
- - -
n 180 Washer
L n “O” Ring (2.5 mm x 12 mm o.d.)
195 Nut (M8 x 1.25 - 6h)
[SS]
MANIFOLD / FLUID CAP MATERIAL OPTIONS PE10X-XXX-XXX-A0S
PE10X-XAX-
PE10X-XCX-
PE10X-XHX-
PE10X-XSX-
Item Description (size)
Qty Part No. [Mtl] Part No.
[Mtl] Part No.
[C] 95990-1
[C] 95990-2
[SS] 96161
[SS] 96159
[CI] 96148
[CI] 96150-[z]
[CI] 96149-[z]
[SS] - - - - -
[Mtl] Part No.
[SS] 95990-1
[Ha] 95990-1
[Ha] 93189-1
[Ha] 95997
[Mtl]
[SS]
[SS]
[SS]
[SS]
[SS]
[SS]
[SS]
[SS]
[SS]
5
6
9
Backup Washer
Diaphragm Washer
Washer (0.505” i.d.)
(2) 95990-3
(2) 95990-3
(2) 93189-1
(2) 95997
[C] 95990-3
[C] 95990-3
[SS] 93189-1
[SS] 95997
14 Screw (M12 x 1.75 - 6g x 25 mm)
15 Fluid Cap
(2) 95935
[A] 95831
[Ha] 96010
60 Inlet Manifold
61 Outlet Manifold
(1) 95936-[z]
(1) 95960-[z]
(2) Y17-125
(2) 96160-2
[A] 95829-[z]
[A] 95830-[z]
[A] Y17-55-S
[A] 96160-1
[Ha] 96008-[z]
[Ha] 96009-[z]
- - - Y17-55-S
- - - 96160-1
63 Pipe Plug (1 N.P.T.) (PE10X-AXX-XXX-A0S)
(R 1) (PE10X-BXX-XXX-A0S)
[SS] - - - - -
z For N.P.T.F. thread models (PE10X-AXX-XXX-A0S), use “-1”
z For BSP thread models (PE10X-BXX-XXX-A0S), use “-2”
EXTERNAL HARDWARE OPTIONS PE10X-XXX-XXX-A0S
COMMON PARTS
PE10X-XXP-
PE10X-XXS-
Item
Description (size)
Qty Part No.
Mtl
[C]
[B]
[B]
Item Description (size)
Qty Part No.
Mtl Part No.
[C] 95880
[C] 95896
[C] 95879
Mtl
1
Rod
(1) 95995
(2) 95843
26 Screw (M8 x 1.25 - 6g x 30 mm)
27 Bolt (M8 x 1.25 - 6g x 40 mm)
29 Hex Flange Nut (M8 x 1.25 - 6h)
n Air Section Service Kit Parts, see page 6.
(8) 95880-1
(20) 95896-1
(20) 95879-1
[SS]
[SS]
[SS]
L n 70 Gasket
Ln 144 “U” Cup (3/16” x 1-1/8” o.d.)
Ln 175 “O” Ring (3/32” x 13/16” o.d.)
(2) Y186-49
(2) Y325-114 [B]
Page 4 of 8
PE10X-X-X-A0S
PARTS LIST / PE10X-X-X-A0S FLUID SECTION
. TORQUE REQUIREMENTS ,
3
1
COLOR CODE
DIAPHRAGM
COLOR
NOTE: DO NOT OVERTIGHTEN FASTENERS.
ALL FASTENERS ARE METRIC.
BALL
COLOR
5
8
MATERIAL
(14) screw, tighten to 25 - 30 ft lbs (33.9 - 40.7 Nm).
(26) screws, 20 - 25 ft lbs (27.1 - 33.9 Nm).
(29) nuts, 15 - 20 ft lbs (20.3 - 27.1 Nm).
Hytrel
Nitrile
Cream
Black
Tan
Cream
Red (S)
Tan
9
10
Santoprene
Santoprene
(Backup)
PTFE
(131) screws, 12 - 17 ft lbs (16.3 - 23.0 Nm).
Green
N / A
White
Yellow (-)
(-) Dash
White
Yellow (S)
(S) Dot
LUBRICATION / SEALANTS
Viton
7
6
k
ApplyLubriplateFML-2greasetoall“O”rings,“U”Cups&matingparts.
x Apply LoctiteR 242 to threads at assembly.
2
4
- Apply PTFE tape to threads at assembly.
~ Apply Loctite 271 to threads at assembly.
Torque Sequence
U Apply anti-seize compound to threads and bolt and nut flange heads
which contact pump case when using stainless steel fasteners.
s Not used with PE10X-XXX-AXX-A0S, -CXX and -GXX.
Z Lubriplate FML-2 is a white food grade petroleum grease.
63 - k
61
FOR THE
26 , U
AIR MOTOR SECTION
SEE PAGES 6 & 7
70 k
68
144 k
131 ,x
A
70 k 29 ,
195
B
69
7
9
22
19 s
21
33 s
27 U
A
15
175 k
74 -
144 k
175 k
B
29 ,
27 U 1 k 180 k
5
22
63 - k
26 , U
60
6
14 , ~
19 s
21
Figure 2
33 s
AUXILIARY VIEW B-B
(models PE10R-XXX-XXX-A0S)
AUXILIARY VIEW A-A
(models PE10R-XXX-XXX-A0S)
View of two piece PTFE diaphragm
k 180
28
180 k
195
Santoprene 8
PTFE 7
PE10X-X-X-A0S
Page 5 of 8
PARTS LIST / PE10X-X-X-A0S AIR SECTION
n Indicates parts included in 637412 Air Section Service Kit shown below and items (70), (144), (175) and (180) shown on page 4.
AIR MOTOR PARTS
Item
Description (size)
Qty Part No.
(1) 95888
(1) 95970
(1) 95901
(1) 96000
(2) 96323
(1) 96170
[Mtl]
Item
Description (size)
Qty Part No.
(1) 96171
(2) Y325-123
(2) 95845
(4) Y178-52-S
(1) 93139
(1) 350-568
(1) 94276
637308
[Mtl]
[B]
101 Center Body (PE10A-X)
(PE10R-X)
[A]
n 166 Gasket
[P]
n 173 “O” Ring (3/32” x 1-3/8” o.d.)
n 176 Diaphragm (check valve)
181 Roll Pin (5/32” o.d. x 1/2” long)
201 Muffler (PE10R-X)
[B]
(PE10S-X)
[SS]
[D]
[SP]
[SS]
[P]
103 Bushing
121 Plug
[D]
n 132 Gasket
[B]
(PE10A-X and PE10S-X)
133 Washer (M6) (PE10A-X and PE10S-X) (3) 95931
[SS]
[SS]
[SS]
[SS]
[SS]
[A]
L n Lubriplate FML-2 Grease
Lubriplate Grease Packets (10)
(PE10R-X)
134 Screw (M6 x 1 - 6g x 25 mm)
(PE10A-X and PE10S-X)
(6) 95931
(6) 96340
(4) 96340
(6) 96340
(1) 96325
MATERIAL CODE
[D] = Acetal
[P] = Polypropylene
[A] = Aluminum
[B] = Nitrile
[SP] = Santoprene
[SS] = Stainless Steel
(PE10R-X)
160 Air Manifold
K
Fluid Section Service Kit Parts, see page 4.
AIR MOTOR SECTION SERVICE
AIR MOTOR SECTION DISASSEMBLY
GENERAL REASSEMBLY NOTES:
1. Remove (160) air manifold, exposing (132 and 166) gaskets and
S Air Motor Section Service is continued from Fluid Section repair.
S Inspect and replace old parts with new parts as necessary. Look for
deep scratches on surfaces, and nicks or cuts in “O” rings.
S Take precautions to prevent cutting “O” rings upon installation.
S Lubricate “O” rings with Lubriplate FML-2 grease.
S Do not over-tighten fasteners, refer to torque specification block on
view.
(176) checks.
2. Remove (121) plugs.
AIR MOTOR SECTION REASSEMBLY
1. Clean and lubricate parts not being replaced from service kit.
2. Replace (173) “O” rings and assemble (121) plugs.
3. Assemble (132 and 166) gaskets and (176) checks to (101) body.
4. Assemble (160) air manifold to (101) body, securing with (134)
screws. NOTE: See “Torque Requirements”, page 7.
S Re-torque fasteners following restart.
Page 6 of 8
PE10X-X-X-A0S
PARTS LIST / PE10X-X-X-A0S AIR SECTION
166 k 121
173 k
173 k
121
160
133
U . 134
43
132 k
176 k
101 181 103
201
Figure 3
. TORQUE REQUIREMENTS ,
NOTE: DO NOT OVERTIGHTEN FASTENERS.
ALL FASTENERS ARE METRIC.
Models PE10A-XXX-XXX-A0S
PE10S-XXX-XXX-A0S
PE10A-X and PE10S-X: Torque (134) screws to 40 - 50 in. lbs (4.5 - 5.6 Nm).
PE10R-X: Torque (134) screws to 35 - 40 in. lbs (4.0 - 4.5 Nm).
Models PE10R-XXX-XXX-A0S
LUBRICATION / SEALANTS
k
U
Apply Lubriplate FML-2 grease to “O” rings, “U” Cups & mating parts.
Apply anti-seize compound to threads at assembly.
166 k 121
173 k
173 k
121
133
160
U . 134
132 k
176 k
101 181 103
201
Figure 4
PE10X-X-X-A0S
Page 7 of 8
TROUBLE SHOOTING
Product discharged from exhaust outlet.
S Check for diaphragm rupture.
S Check tightness of (14) diaphragm screw.
Low output volume, erratic flow, or no flow.
S Check air supply.
S Check for plugged outlet hose.
S Check for kinked (restrictive) outlet material hose.
S Check for kinked (restrictive) or collapsed inlet material hose.
S Check for pump cavitation -- suction pipe should be sized at least as
large as the inlet thread diameter of the pump for proper flow if high
viscosity fluids are being pumped. Suction hose must be a non-col-
lapsing type, capable of pulling a high vacuum.
S Check all joints on the inlet manifolds and suction connections.
These must be air tight.
Air bubbles in product discharge.
S Check connections of suction plumbing.
S Check “O” rings between intake manifold and inlet side fluid caps.
S Check tightness of (14) diaphragm screw.
Motor blows air or stalls.
S Check (176) check valve for damage or wear.
S Check for restrictions in valve / exhaust.
S Inspectthepumpforsolidobjectslodgedinthediaphragmchamber
or the seat area.
DIMENSIONAL DATA
(Dimensions shown are for reference only, they are displayed in inches and millimeters (mm).
1 - 11-1/2 N.P.T.F. - 1 (PE10X-AXX-XXX-A0S)
1 - 11 BSP (PE10X-BXX-XXX-A0S)
Exhaust Port 3/4 - 14 N.P.T.
A
S
E
E
Q
T
F
P
L
Outlet
G
B
R
M
Inlet
D
K
N
H
Air Inlets 1/4 - 18 N.P.T.F. - 1
C
J
DIMENSIONS
A - 12-11/32” (313.2 mm)
F - see below
L - 1-1/2” (38.1 mm)
M - 6-3/32” (154.8 mm)
N - see below
P - see below
Q - see below
R - 3/4” (19.1 mm)
S - 17/32” (13.3 mm)
T - 1-3/64” (26.6 mm)
B - 11-9/16” (293.7 mm)
C - 4” (101.6 mm)
D - 1-1/4” (31.8 mm)
E - see below
G - 12-7/16” (315.9 mm)
H - 6-1/4” (158.8 mm)
J - 7-5/16” (185.7 mm)
K - 13/32” (10.3 mm)
“E”
“F”
“N”
“P”
“Q”
PE10A-X-X-A0S
12-3/4” (323.3 mm)
8-1/8” (206.4 mm)
8-5/16” (211.1 mm)
8-3/16” (207.9 mm)
PE10X-XAX-X-A0S
PE10X-XCX-X-A0S
PE10X-XSX-X-A0S
1/4” (6.4 mm)
9/32” (7.1 mm)
9/32” (7.1 mm)
5-27/32” (148.2 mm)
5-15/16” (150.2 mm)
5-27/32” (148.2 mm)
12” (304.8 mm)
12-3/32” (306.8 mm)
12” (304.8 mm)
PE10R-X-X-A0S 9-25/32” (248.5 mm)
PE10S-X-X-A0S 12-25/32” (340.1 mm)
Figure 4
PN 97999-1088
PE10X-X-X-A0S
Page 8 of 8
|